Dynamco TX11 Remote Relay Transmitter User Manual

Download:
Mirror Download [FCC.gov]
Document ID	150621
Application ID	TiBiSrmNhw3RZ/fRZkeQ4Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	234.78kB (2934785 bits)
Date Submitted	2001-05-18 00:00:00
Date Available	2001-05-18 00:00:00
Creation Date	2001-05-18 18:20:11
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-05-18 18:20:13
Document Title	User Manual

NoslzmImmobiliserUserlnslmclions l‘ ‘ 3
NOSTART
USER
MANUAL
GENERAL DESCRIPTION
The NOSTART relay system is designed to replace existing vehicle relays in order to
provide vehide immottilieation. No installation work is required, all compatible vehicle
relays are removed from the factory designed socket and a NOSTART relay is simply
inserted into the empty socket. Specific vehicle notes may be found at
mwmnogtettoom
SYSTEM TYPES
NOSTART systems use either sophisticated code super-position techniques or pseudo
random RF code encryption to disarm ltie relay. Once the relay is disanned. it‘s normally
closed contade are cloned to complete the immobilised circuit.
DISARMING
Remote systems: to disarm a NOSTART relay. simptytum the vehicle's ignition switch to
the ON position and press the main button on a valid remote control.
Digitally Coded Key (DiCK): to disarm the NOSTART relay sinply insert the DiCK into the
vehicle's cigarette lighter socket and start the engine.
ARMING
There is no need to arm the NOSTART relay. All arming functions are controlled by the
controller contained inside the relay.
- While pm is applied to either pins A or B. while grounding any other pin, the
NOSTART is powered up.
~ While power is applied to either C or D, while grounding any other pin. the NOSTART is
powered up with ignition ON.
~ The NOSTART will arm immediately when all power is removed. It will re-arm after 30
seconds it the power remains on and ¢12VDC is not detected on pins C or D.
EMERGENCY OVERRIDE
In cases of lost. stolen or Vault remotes. the NOSTART system comes complete with an
over-ride procedure.
1. Simpty insert the vehicle's ignition key into the ignition switch.
2. Turn to the ON position tor a minimum of five seconds. then switch OFF.
3. Repeat step #2 a total 01 five times.
Nostart Immobiliser User Instructions ' 2 3 ,
The NOSTART system will disarm immediately. allowing the engine to start. The
NOSTART will re—ann automatimlly as per normal once the ignition is switched oft. To re»
start the engine, repeat the entire over-ride procedure.
REPLACING BATTERIES IN REHQ‘I’ E CONTROLS
Using a small Phillips-head screw driver.
removethethreescrewaatthe backofthe
remote and carefully separate the no body
houshgstakingtakecarencttodiehnbthe
circuit board. Remove the old balmy Miltst
paying attention to the orientation of the
positive and negative terminals, Insert new
battery in identical fashion to the original and
reassemble remote. Replace news and test
remote control by precelng main button. For further information, please contact your local
Identimarlr service centre. Remote battery type 27a.
SYSTEH DECRIPHON and INSTALLATION CRITERIA
The NOSTART is designed to replace any normally open automotive relay, where the
connect current does not esceed 20ampe. Different pin layouts are required for different
relay manufacturers. Please order as per vehicle requirements.
RELAY CONT ACT DESCRIPTIONS
ALL PINS - each pin of the NOSTART relay is used to pickup power or ground when
either is applied. This process is automatic, hence no polarity considerations are
necessary.
A PIN: Normally open contact. this pin will act as the output of the relay. Any signal
injected into pin 8 will appear on pin A when the NOSTART is disarmed and 4>12VDC is
detected on pins C or D.
a s12VDC or ground on this pin will act it the same manner and the power supply to
a ncnnal immobiliser.
8 PIN : Common contact. this pin will act as the input to the relay contacts. Signals
applied to this pin will only appear on pin A when the NOSTART is disarrned and
+12VDC is detected on pins C or D.
- - Any HZVDC or ground on this pin will act in the same manner and the power
supply to a normal immoblllser.
C PIN: Coil input, this pin activates the coil inside the NOSTART. If the NOSTART is
disam-ed, any 012VDC on this pin will cause the relay contacts to close.
- Any +12VDC on this pin will act in the same manner and the ignition to a normal
immobiliser
a Also any +12VDC or ground on this pin will act in the same manner and the power
supply to a normal inmobiliser.
D PIN Coil input, this pin aarvates the coil inside the NOSTART. II the NOSTART is
disanned. any ~12VDC on this pin will cause the relay contacts to close
L)
..
Noslarl lmmohiliscr User Instructions
- Any 012VDC on this pin will act in the same manner and the ignition to a normal
immobiliser.
- Also any +12VDC or ground on this pin will act in the same manner and the power
supply to a numial immobiliser.
NORMALLY OPEN CONTACT
WEN/GROUND
iGNITlON/GROUND
C lGNlTlON/GROUND
RELAY COIL SUPPLY RELAY co||_ SUPPLY
POWER/GROUND
COMMON CONTACT
Information to user : Changes of modifications not expressly
approved by the manufacture could void the user's
authority to operate the equipment.
This device complies with Part l5 of the FCC Rules. Operation is subject to the
following two condilions: (I) this device may not cause
harmful inlerfcrcncc‘ and (2) this device musl acccpl any interference
received, including interference that may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:05:18 18:20:11
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:05:18 18:20:13-04:00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools