user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1310116 |
| Application ID | Tup6Oht8HjtBOxrKiq7ZOA== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 178.53kB (2231563 bits) |
| Date Submitted | 2010-07-13 00:00:00 |
| Date Available | 2010-07-16 00:00:00 |
| Creation Date | 2010-07-12 13:29:01 |
| Producing Software | Adobe Acrobat 7.1 Image Conversion Plug-in |
| Document Lastmod | 2010-07-12 13:29:01 |
| Document Title | user manual |
| Document Creator | Adobe Acrobat 7.1 |
cyclops Seoul-iv Systems as? E.- n“. -N_ Mann-ii -AU_AM=H. ToolGuard'" 11510000 Quick- start Installa n Guide Introduction Congratulations onpurcnasing a TGADDO'“ Alarm to protect gour toolbox or truck- bed contents. For installation of the memo“ Alarm, you will need the following basic tools: ~ A small Phillips-head or "Star" screw- driuer, ~ An alcohol based cleaner like Meth lated Spirits to ensure the instal tion surface is free of dlrt, dust and moisture A Proper care e; safety precautions should be taken when using any cleaning fluids Installation Guide Before the TGhooo'“ will operate, a new set of 3 x AA Alkaline batteries must be inserted into the batterg compartment, Awarnlng! This Alarm is extremely loud Please use aare wnen testing and wnen inserting batlenesto auoid nearing damage . Remoue the two top retaining screws from the TGhooo'“ case. ~ Slide the lid towards the edge of the case Note tne battery polarity markings inside the compartment, ~ Insert and slide the left-most and right- most batteries into position. ~ Leuer the middle batterg between the outer two. ~ Slide the lid into its Original location and replace the two retaining screws to hold the lid closed, suitable Location for Fi ing The Tattoos“ Alarm was designed to be mounted on the inside of a toolbox lid or truck tray couer, and is effectiue forany lid or couer that tilts uerticallg. For a Toolbox, we recommend that the alarm be installed inside the lid, reasonably close to the opening edge Mounting the Alarm Special high-strength double-sided tape is supplied and is the preferred method of installation as it is quick, easy and uery strong. Wipe the mounting area with Meth lated Spirits or similar, to ensure the su ace is clean and free of oil, dlrt and moisture. A Proper care e; safety precautions should be taken when using any cleaning fluids carefullg remoue the non-stick coating from one side of the double-sided tape and stick the strips of tape to the back of the alarm towards each side. Testing the 766000“ A The following procedure causes the siren to sound. please taire all precautions to preuenl hearing damage we suggest meanng ear—plugs or passrue protection eur—mufis To test the TGAOOO‘“ has been installed and is functioning correctly, please follow these steps: . Close the toolbox or hatch on which the alarm has been mounted, ~ Press the button on the remote control that was supplied in the kit. The siren will chirp twice. - Wait for a minimum or 5 seconds to allow the alarm to establish its reference angle. ~ Open the lid or hatch. The siren will sound for thirty seconds, or until the remote control is pressed once more. Usu- Guide Arming To Arm the TGADOO'“, simply press the button on tne remote control. The siren will emit two short chrrps to confirm. The alarm calculates its reference an le during the lst four seconds, after which any real tilt will trigger the siren. Disarming To disarm the alarm, simply- press the button on the remote contro The siren willemitasinglechirptooonnrm disarm. Triggering The TGADDO‘” resets its reference angle each time the alarm is armed. Any change in angle with respect to the reference angle will cause the siren to sound for 30 seconds. The sirm will then reset (remain quiet) and the alarm will reset the reference angle to its new an Le, ready to trigger upon t e next change, his cycle will continue until the alarm is disarmed. Troubleshooting mourn solution My alarm fails 1 Ensure the remote battery to rspond is not flat Red LED on remote to remote should glow ongntly control 1 Reprogrom the remote ta the alarm, see “Programming a new Remote Control” section in the full online document" 3 Check correct installatian of the alarm batteries Why does my this is a low battery alarm chirp warning and Indicates that three times your alarm requires new after I disarm? batteries Why does my This is also a low battery alarm pulse warning that inrorrris the the siren rather user that the battery has than sounding dropped since arming a tanstant Siren tone? Technical Support “ V|s|t wwwtoolguardcom to see the full uersion of the User and installation Guide and for further technical information. Warn-mtg Please register your serial number to receiue your warrantg certificate by going to wwwtoolguardcom/register YOUR SERIAL NUMBER IS: MAHE'O txcluswt ovclors SPEIFIGAVIONS IN cmm mans VENDING rrr. wimmnn um mu or hand wu’wiy mmtri.iimrisiixlcussflaiul-awiu puruurlm m o aiir- roc not not. «or m M ir rrr. macmvimwrirt tan a our. rcc non owner mom p tr. Mow-ii; lwa we". itmn am. no, riotous. Wehrma- w 1mm om. nun mu m, harm. more momma no at“ untamed oar-nan u 5 6 8 3 0 0 0 2 0 0 5 TooIGuard TG4000 >ibox Alannjimer IriSSi'Llril indd 2 15/05/10 3 44 P
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes XMP Toolkit : 3.1-702 Modify Date : 2010:07:12 13:29:01+08:00 Create Date : 2010:07:12 13:29:01+08:00 Metadata Date : 2010:07:12 13:29:01+08:00 Creator Tool : Adobe Acrobat 7.1 Format : application/pdf Document ID : uuid:f49e9009-2892-44b4-9061-a04d713cc442 Instance ID : uuid:be3dbfba-d011-49cd-ba9c-8469bbd2c7f5 Producer : Adobe Acrobat 7.1 Image Conversion Plug-in Page Count : 2 Creator : Adobe Acrobat 7.1EXIF Metadata provided by EXIF.tools