Dynamco TX97 Remote Relay (Transmitter) User Manual
Dynamco Pty. Ltd. Remote Relay (Transmitter) Users Manual
Dynamco >
Users Manual
JR4RALJEHHQZ75
USERINSTRUCTYOAS
GUR/
a“ {A
CYC LQPS
H’sre“
Proudly designed and engineered in
Australia by Dynameo Pty Ltd. "
Proudly
Australian
Immobiliser Vehicle MM"
S ”t S t
cyifip‘iilltméfif’" cchPs
. w’srefig
User Instructions
Congratulations on having one of the world's most advanced
and unique Australian designed and engineered vehicle security
systems, installed in your vehicle!
The Cyclops Paralyser 275 has been tested to and meets
Australian Standards 460121999.
ARMING AND DISARMING
To arm or disarm the system, press the main button on the remote control.
Arming the system is accompanied by two flashes from the indicators
and one flash for disarming (indicator connection is an optional extra).
AUTO-ARMING
The system is designed to automatically immobilise the vehicle. The engine will be
immobilised within 40 seconds after the ignition switch has been turned off. If
disarmcd by remote control, the system will rc-arm (immobilisc) itselfwithin the same
time period.
ENGINE IMMOBILISATION
When the system is amied the engine is immobilised. The two independent, normally
open circuits of immobilisation ensures the engine is starved of either fuel or spark.
Iinniobilisatiori points vary fioni vehicle to vehicle, common engine kill places include
fuel injection. fuel pump. fuel cut-ofl' solenoids, main ignition feed. low-tension
distributor supplies and starter motor solenoids. etc.
.3.
OVERRIDE
The system can be overridden by means of a Personal Identification Number (PIN). Every unit is supplied
with its own PIN. It is important to make a note ofthis PIN or keep the card supplied with the unit in a safe
p 1 ace as it also has the PIN detailed on it.
"* Any digit marked ‘0', indicates 10 flashes.
OVERRIDE PROCEDURE
- Insert the ignition key into the ignition switch and turn to the ON position. The red status LED mounted on
the dash Will glow constantly.
- Turn the ignition key back to tlieACC position, the status LED will begin to flash slowly. Count the number
of flashes for the first digit in the PIN of the P275. Return the key to the ON position when the correct
numberis counted.
chcut 5th 2 for the remaining digits in the PIN. When all four digits are entered. the indicators/ status LED
will flash once, the P275 will then disarm. NB: lfthe engine is not started with 40 seconds ofovei-riding,
the P275 with immobilise the engine.
PROBLEM SOL VING
Unit won’t arm/disarm
- Make sure that ignition sw1teh is in the OFF position.
1 Make sure the vehicle hatteiy is not flat
. Try your spare remote transmitter unit. 4
The remote fails to operate
If the LED does not light up when a remote control button is pressed. change the battery
BA TTER Y REPLA CEMENT
Using a small Phillips—head screwdriver, remove the three screws at the back of the remote and carefully
separate the two body housings taking take care not to disturb the circuit board. Remove the old battery whilst
paying attention to the orientation of the positive and negative terminals Insert new battery in identical
fashion to the original and rc-assemble remote. Replace sciews and test remote control by pressuig main
button For further information, please Contact your local Cyclops servicecentre‘
Remote battery type is CR2032 - 3Volt Lithium.
SPECIFICATIONS
Manufactured by Dynamco Pty Ltd
Model number Paralyscr 275
mi} 1999
i wSAupply voltage +liVDC 7 7
‘ Cuiieiitconsuiiiptioii flu; devme may no! cause mum xmexiexeuce. and (z) um dnicc mm accept any interference
rectum. inchv‘hng unerference llw may came “named operation
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2006:05:25 20:16:13+08:00 Create Date : 2006:05:25 20:15:27+08:00 Creator : Acrobat 5.0 Scan Plug-in for Windows Page Count : 5 Mod Date : 2006:05:25 20:16:13+08:00 Creation Date : 2006:05:25 20:15:27+08:00 Producer : Acrobat 5.0 Scan Plug-in for Windows Metadata Date : 2006:05:25 20:16:13+08:00EXIF Metadata provided by EXIF.tools