Dyson Airblade Tap Technical Specifications
2015-08-14
: Dyson Dyson-Airblade-Tap-Technical-Specifications-800080 dyson-airblade-tap-technical-specifications-800080 dyson pdf
Open the PDF directly: View PDF 
.
Page Count: 4
Product range
AB09 Short AB10 Long AB11 Wall
Electrical
Input voltage/Frequency: 220-253V 50 Hz
Rated power: 1600 W
Motor type: Dyson digital motor – brushless DC Motor
Motor switching rate: 6,000 per second
Motor speed: 90,000 rpm
Operating temperature range: 0° – 40°C
Heater type: None
Standby power consumption: Less than 0.5 W
Construction
Tap construction: Stainless steel (brushed)
Under counter motor assembly construction: Moulded ABS (main unit)
Exterior screw type: Torx T15
Water ingress protection to IP35
Filter
HEPA filter (glass fibre and fleece prelayer)
Bacteria removal 99.9%
Operation
Touch-free infra-red activation
Hand dry time measurement: 12 seconds (Measurement based
on National Sanitation Foundation Protocol P.335)
Operation lock-out period: 30 seconds
Airspeed at apertures: 430 mph
Operating airflow: Up to 30 l/s
Maximum altitude: 2,000 metres
Water operation
Water flow rate: 4 l/min
Tap Aerator: Aerated water outlet
Tap power supply: Mains supply
Water temperature control: Thermostatic mixer recommended (not supplied)
Water pressure required: 1-8 Bar
Logistics
Serial number prefix: AB09 EC1; AB10 EC2; AB11 EC3
Single unit order code: AB09 25818-01; AB10 25819-01; AB11 25820-01
Net weight: AB09 4.3kg; AB10 4.6kg; AB11 9.0kg
Packaged weight: AB09 5.7kg; AB10 6.1kg; AB11 11.4kg
Packaged dimensions: AB09 H303 × W284 × D286 mm
AB10 H276 × W437 × D280 mm; AB11 H302 × W610 × D375 mm
Unit barcode: AB09 5025 1550 1577 3;
AB10 5025 1550 1578 0; AB11 5025 1550 1579 7
Sink specification
The Dyson Airblade Tap hand dryer is compatible with most sink types.
Ensure plugs are not installed in the sinks.
Sink dimensions: All sink measurements are internal unless stated otherwise.
Width of sink – Minimum: 350mm, Front to back – Minimum: 300mm
Depth of sink – Minimum: 100mm
Maximum depth of sink for AB10 only: 200mm (External measurement
of vessel sink).
Sink materials: Sinks with highly polished surfaces should be avoided e.g.
reflective chrome. Porcelain or brushed metal are ideal. When multiple taps
are installed side-by-side, tap centres should be a minimum of 580mm apart.
Standard guarantee
5 year guarantee
For further information please contact Dyson.
0800 345 7788 (UK) 01-401-8300 (IE)
www.dysonairblade.com
The NSF logo is a registered trade mark of NSF International.
The Carbon Reduction Label is the registered trade mark of the Carbon Trust.
HACCP International non-food certification mark is the registered trademark of
HACCP International. HACCP International have certified Dyson products based
on their recommended installation and operating conditions. Licensed by Dyson.
TECHNICAL SPECIFICATION
SIDE ELEVATIONFRONT ELEVATION
Fixing
locations
(4) Fixing
locations
(4)
Water
entry point
All dimensions shown
in mm (+/-5mm)
Rear cable
entry point
Floor
Minimum clearance
Z 100mm clearance from floor.
Tap dimensions
AB09 Height 159mm Width 297mm Depth 286mm
Motor bucket dimensions
AB09 Height 266mm Width 142mm Depth 189mm
FLOOR
142
266
297 286
52.2
50.8
For further information please contact Dyson.
0800 345 7788 (UK) 01-401-8300 (IE)
www.dysonairblade.com
297
309
286
142
266
52.2
50.8
TECHNICAL SPECIFICATION
FRONT ELEVATION SIDE ELEVATION
Fixing
locations
(4)
Fixing
locations
(4)
Water
entry point
All dimensions shown
in mm (+/-5mm)
Rear cable
entry point
Floor
Minimum clearance
Z 100mm clearance from floor.
Tap dimensions
AB10 Height 309mm Width 297mm Depth 286mm
Motor bucket dimensions
AB10 Height 266mm Width 142mm Depth 189mm
FLOOR
FRONT ELEVATION
TECHNICAL SPECIFICATION
SIDE ELEVATION
Fixing
locations
Water
entry
point
Cable
entry
point
Tap dimensions
AB11 Length 312mm Width 297mm
Motor bucket dimensions
AB11 Height 266mm Width 142mm Depth 189mm
FLOOR
