ELITEGROUP COMPUTER SYSTEMS 6000IABG Notebook User Manual 600 E V1

Download:
Mirror Download [FCC.gov]
Document ID	539884
Application ID	SXt3Lv0SQt+Wl29ZiJOE9Q==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	167.45kB (2093147 bits)
Date Submitted	2005-05-05 00:00:00
Date Available	2005-05-05 00:00:00
Creation Date	2005-05-05 16:36:33
Producing Software	Acrobat PDFWriter 5.0 for Windows NT
Document Lastmod	2005-05-05 16:36:55
Document Title	600 _E_ V1.doc
Document Creator	600 (E) V1 - Microsoft Word
Document Author:	Cathy

VGA UTILITIES
After you have restarted Windows, open the “Control Panel” and double
click on the “Display” icon. From the “Display Properties” window,
select the “Settings” tab and click on the “Advanced” tab to enter the
“(Multiple Monitors) on ATi MOBILITY RADEON X700 Series
Properties" window.
51
ATI OpenGL
ATI’s Display
The ATI’s Display driver allows three simultaneous outputs to LCD,
CRT, LCD/CRT, TV/LCD, LCD/TV and CRT. Before proceeding, be
sure the monitor is connected to the computer. User can also use hotkeys
by typing the name that corresponds with the combinations mentioned
above.
52
53
Color
You can adjust the right resolution for your screen display.
54
Options
Display all the items concerning the ATI related function.
55
Overlay
56
ATI PowerPlay
57
Direct 3D
58
VIEWING LIVE VIDEO (OPTION)
The Utility allows you to access the entire range of display controls and
configuration options. Its live video can co-exist with other applications
running at the time. In addition, you have the choice of keeping the
default video window size, scaling it to any other size or using the entire
screen for video display. You can either sit in front of your monitor,
controlling the video with menu commands, toolbar buttons as well as the
TV Tuner, or lay back in your chair with the remote control pad in your
hand.
For more detailed information on the function for each
individual mode on the Remote Control, please refer to the
Remote Control Guide user’s manual.
59
Using the Remote Control
The Remote Control comes with three
multimedia
softwares:
WinDVR,
WinDVD, and WinRip. These softwares
use only one remote control; the function
of each buttons will vary on different
software.
• DVR Mode Button - Press the DVR
button if you want to use the
WinDVR software. “WinDVR” gives
you high-quality digital recording of
your favorite TV shows on your PC.
• DVD Mode Button - Press the DVD
button if you want to use the
WinDVD software. “WinDVD” uses
the power of your PC to bring DVDs
to life.
• RIP Mode Button - Press the
Music/Audio DJ button if you want to
use the WinRIP software.
WinDVR Mode
Cable Connection
Your notebook supports three video standard namely: NTSC, PAL and
SECAM. Ask your local dealer on the type of standard being used in
your respective country of origin.
•
•
60
Remove the cover on the cable TV connector at the rear of the
computer with the aid of a screwdriver .
Connect one end of the cable wire to the RF connector of the
computer while the other end is connected to the wall socket or
directly to the antenna.
Defining the Video Source
Select the PAL, NTSC or SECAM, depending
on which standard the selected source is using.
The factory default is the standard used by your
purchase country, and normally there is no need
to change this setting.
If you are working outside your country, you
are required to adjust the setting of our video
source. From the WinDVR window, click on
your mouse right button and select the “Setup”
item.
From the “Setup” dialog window, click on the
“Standard” selection items and drag down the
arrow to select on the type of TV standard
based on your respective country of origin.
61
Application buttons in DVR mode
Ø TV - Launch the WinDVR application
Ø Channel Surfing - Surf channels by displaying 16 channels at
once.
Ø Full screen - Change display size to full screen.
Ø Mute - Mute or restore sound when watching TV.
Ø C.C. (Close Caption) - Display overlay text caption.
Ø MTS/SAP - Switch TV sound mode to mono stereo or SAP
Ø Scan (Auto scan) - Scans all available channels for context.
Ø Arrow Up and Down - Navigates up or down.
Ø Arrow Left and Right - Navigates left or right.
Ø Cancel - Cancel last operation.
Ø Select - Selection.
62
Ø CH Up & Down - Selects next
higher or lower channel in channel
memory.
Ø Replay – Playback previous sequel
after pressing the TimeShift.
Ø Skip - Skip the recorded program.
Ø Volume (Volume up and down) Increase and decrease sound.
Ø Stop - Stops functions such as
record, play, rewind, forward and
pause.
Ø Play/Pause - Plays or pauses a
scene.
Ø Record - Records TV and encodes
it into MPEG I/II format.
Ø TimeShift - Pauses live TV.
Ø Real Screen (Go Live) – Stop
timeshift.
Ø Snapshot - Captures a favorite
screen shots from the program.
Ø Numeric Keypad (0-9) - Select a
channel up to 99 by pressing two
numbers.
63
Application buttons in DVD mode
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
64
DVD - Launch the WinDVD application.
Audio Selection - Selects a language.
Subtitle - Activates language subtitles.
Full screen - Change display size to
full screen.
Angle (Angle Selection) - Allows
multiple angle viewing
Mute - Mute or restore sound when
watching CD title or MPEG file.
Arrow Up and Down - Navigates up
or down.
Arrow Left and Right - Navigates left
or right.
Cancel - Cancel last operation.
Select - Selection.
Speed - Speed up the play.
CHAPTER (Previous & Next) Selects previous or next chapter.
Volume (Volume up and down) Increase and decrease sound.
REW - Play disc in fast reverse mode.
FWD - Play disc in fast forward mode.
Stop - Stops the current play.
Play/Pause - Starts or pause the disc.
Step Forward Single frame advance while in pause mode.
Bookmark - Instantly mark your favorite scene.
Menu - Opens DVD title main menu.
SnapShot - Captures still images of current playback.
Numeric Keypad (0-9) - Inputs chapter number to playback.
Please take note that when you are playing the DVD
applicaton, you will only be able to use the Remote Control
DVD button if your system support the InterVideo WinCinema
application.If your system support the WinXPMCE application,
you will have to use the “Microsoft Remote Control” that
comes with your package.
Use Lunch key to chosoe between these two applications,
please proceed to BIOS Setup and select the “Advanced”
menu. From the “Shortcut Key Working With” selection item,
select the “InterVideo” if your system only support the
”InterVideo” application or the “WinXP MCE” application if
your system support the Microsoft’s WinXP MCE application.
Limitation when playing DVD files
The computer allows you to connect external devices such as monitor and
TV to your notebook computer. Open the “Control Panel” and double
click on the “Display” icon. From the “Display Properties” window,
select the “Settings” tab and click on the “Advanced” tab to enter the
“(Multiple Monitors) on ATi MOBILITY RADEON X700 Series
Properties" window.
65
Click on the “Displays” tab to set the monitor or TV or LCD as your
“Primary” display device to play the DVD files.
The VGA driver default value set the LCD as Primary display
device. If the LCD is set as “Primary” display therefore the
video image will not display on the monitor or TV. However, if
you wish to have the video image display on your external
display devices, set the monitor or TV as your “Primary”
display device.
66
Application buttons in Music mode
Ø Music - Launch the WinRIP
application.
Ø DSP Toggle – Let you enable or
disable the DSP window when the
WinRIP application is launched.
Ø Mute - Mute or restore sound when
playing music.
Ø Arrow Up and Down - Navigates up
or down.
Ø Arrow Left and Right - Navigates left
or right.
Ø Cancel - Cancel last operation.
Ø Select - Selection.
Ø Track (Previous & Next) - Plays
previous or next track in the list.
Ø Volume (Volume up and down) Increase and decrease sound.
Ø Shuffle - Play tracks in random order.
Ø Repeat - Repeat current track or all
tracks.
Ø Stop - Stop playback.
Ø Play/Pause - Play or pause a music
track.
67
68
T ROUBLESHOOTING
This chapter describes locating and solving problems that you may
encounter while using your computer.
Locating a Problem
Problems with your computer can be caused by something as minor as an
unplugged power cord – or as major as a damaged hard disk. The
information in this chapter is designed to help you find and solve minor
problems. If you try all the suggested solutions and you still have a
problem, make a list of what steps you have taken to correct the problem
and contact your dealer.
Successful troubleshooting is the result of careful observation, deductive
reasoning, and an organized approach to solving the problem.
The problems that you will encounter can be divided into two basic
categories: hardware problems and software problems. Hardware
problems can be further divided into electrical and mechanical problems.
You will know you have a hardware problem if the screen is dark, the
computer cannot read the disk drives, or you get an error message during
the Power-On Self Test (POST).
Software errors can occur at several levels. The ROM BIOS and the
operating system can give you a large number of error messages. On top
of this, each application software package has its own set of error
messages. It is important to determine whether the software error me ssage
you are getting is from the application or the operating system. Once you
know this, you can look in the respective manual for a solution to the
problem.
Checking Cables and Connections
Start by performing a careful visual inspection of the exterior of the
computer. If no LEDs are illuminated, make sure that your computer and
its peripherals are getting power and communicating with each other
properly.
To check the power cables, and connections:
69
1.
2.
3.
4.
If you have been using battery power, connect the Notebook to an
external power source and make sure that the battery has a charge.
If you are using the Notebook with the AC adapter, check the power
outlet, the power cord, and any power switches that may affect your
computer.
• Check the wall outlet or power strip with an item that you
know is functioning properly. A lamp or radio is a
convenient item for checking the power. You may also
need to check the fuses and breakers in your electric box.
• If the outlet is controlled by a wall switch, make sure that
the switch is on.
• If the outlet is controlled by a dimmer switch, use a
different outlet.
• If your computer is plugged into a power strip with an
On/Off switch, make sure the switch is on.
With the computer’s power switched off, check all cable connections.
If the computer is connected to any peripheral devices, look for loose
or disconnected cables.
• If the computer is too close to a wall, a cable connection
may be loose or the cables may be crimped.
• Do not substitute cables for different devices (other than
the manufacturer recommended cables) even if they look
exactly alike. The wiring inside the cable may be
different.
When you are certain that you have power available and all
connections are good, turn the computer on again. If the computer
still does not start, you may have a hardware problem.
The Power-On Self Test
The Power-On Self Test (POST) runs every time you turn on or reset the
Notebook. The POST checks memory, the main system board, the display,
the keyboard, the disk drives, and other installed options.
A few seconds after you turn on your computer, a copyright message
appears on your display screen. A memory test message appears next; as
the test continues, memory size increases until all installed memory is
tested. Normally, the only test routine visible on the screen will be the
memory test.
Two classifications of malfunctions can be detected during the POST:
• Error messages that indicate a failure with either the hardware, the
70
software, or the Basic Input/Output System (BIOS). These critical
malfunctions prevent the computer from operating at all or could
cause incorrect and apparent results. An example of a critical error
is microprocessor malfunction.
• Messages that furnish important information on the power-on and
boot processes (such as memory status). These non-critical
malfunctions are those that cause incorrect results that may not be
readily apparent. An example of a non-critical error would be a
memory chip failure.
In general, if the POST detects a system board failure (a critical error),
the computer halts and generates a series of beeps. If failure is detected in
an area other than the system board (such as the display, keyboard, or an
adapter card) an error message is displayed on the screen and testing is
stopped. It is important to remember that the POST does not test all areas
of the computer, only those that allow it to be operational eno ugh to run
diagnostic programs.
If your system does not successfully complete the POST, but displays a
blank screen, emits a series of beeps, or displays an error code, consult
your dealer.
General Hardware Problems
A few common hardware problems and suggested solutions are presented
in the table below:
Problem: The capacity of the battery is between 95 to 99% but
can not fully charged.
Solution: Please discharged to less than 95% of its capacity
then recharge the battery.
Problem: Failure in the installation of the Audio driver.
Solution: Be sure to first remove the current audio device from
your system. Please follow the instruction on the installation of
audio driver.
Problem: The display screen is dark
Solution: Make sure that the computer is not in Suspend mode.
Check the Brightness controls for the screen. If the controls are
turned too far down, the screen will be dark.
Problem: An incorrect date and time are displayed.
Solution: Correct the date and time using the DOS DATE and
TIME commands or the options in the Setup Utility. If the date and
time become incorrect after a short time, your CMOS battery may
71
be depleted. Contact your dealer to change the battery.
Problem: You hear irregular beeps during operation of the
Notebook and the system halts.
Solution: The problem is beyond the scope of this manual.
Contact technical support.
Problem: An unidentified message is displayed.
Solution: Reboot the computer and run the BIOS system setup.
Confirm the Setup parameters. If the same message is displayed
after booting up again, contact technical support for assistance.
Problem: The system cannot access the DVD-ROM drive.
Solution: Check that a CD is properly inserted in the drive.
Make sure that you are using the correct program for that kind of
CD. For example, the system cannot read a data CD using an
audio program.
Problem: You cannot operate the printer.
Solution: Check the printer USB cable connection. Ensure that
the printer power switch is turned on. Confirm that the printer is
on-line.
Problem: You cannot use the mouse.
Solution: Check the cable connection.
Check the mouse with another application to see if there is a
software incompatibility problem.
If possible, check the mouse with another computer to see if it
works. If it doesn’t operate on a different system, the mouse might
be broken.
Problem: The fan does not stop operating when the system
enters the suspend mode.
Solution: Before entering the suspend mode, the fan still
operates in full speed to lower down the temperature of the system.
When the system temperature reduces into normal condition then
the fan will gradually slow down into its normal speed.
Contacting Your Dealer
If you still have a problem after reading the preceding sections, the next
step is to contact your dealer. Your dealer can determine if the problem is
something that requires the computer to be taken to the shop. Before you
call your dealer, however, prepare the following information:
• How is your computer configured? Your dealer needs to know what
72
•
•
•
peripheral devices you are using.
What messages, if any, are on the screen?
What software were you running at the time?
What have you done already to try to solve the problem? If you
have overlooked a step, your dealer may be able to solve the
problem over the phone.
73
Page intentionally left blank
74
HOW DO I EXPAND MY
NOTEBOOK
Turn off the computer; disconnect the AC adapter and all peripherals.
With your computer turning upside down, remove all the screws that are
encircled and shown on the illustration.
75
Upgrading your Memory
1.
2.
3.
4.
5.
76
If you need to install a higher capacity module, gently push the edge
clips on both sides to release the module.
Angle the card slightly upward and gently slide it from its edge
connector slot. Store the card in the anti-static bag that contains your
new module(s).
To install the new memory card, hold the card with its gold edge
connector toward the edge connector slot of the compartment. To
help you orient the cards, the edge connector has been made with
two unequal-length sections. You will only be able to insert the c ard
in one direction.
Insert the edge connector into the slot. The gold edge connector of
the card should not be visible when the card is fully inserted.
Press the card downward where you should hear an audible click as
the latches of the connector secure the card in place.
Easy to Upgrade HDD Module
The hard drive in your notebook computer is made to be easily swapped
out for upgrading.
How to Remove your Hard Drive
1. Remove the screw that secure the compartment cover and set them in
a safe place.
2. Remove the HDD cover from the compartment.
3. The drive is attached to a special bracket that secures it to the
notebook computer.
4. Gently hold the grip of the HDD, Πlift it up to release from its
compartment.
5. Push the • HDD slightly in the direction of the arrow as shown in
the illustration to release it from the pins of the drive.
77
How to install your New Hard Drive
1. You will need to align the tabs on the drive bracket with the slots on
the bay.
2. Press down gently on the drive bracket until it engages with the
system. Do not force the drive into place this can bend the pins on
the hard drive.
3. Secure the cover with the screw.
78
SPECIFICATION
Detailed Notebook Specifications
Core Logic
•
•
•
•
•
•
Intel® Pentium® M processor Dothan 1.86GHz
478pin mFCPGA package
Microsoft® Windows ® XP Professional Edition
Microsoft® Windows ® XP Home Edition
Microsoft® Windows ® XP Media Center Edition
Intel® 915PM (Alviso)+ ICH6-M
Memory
•
512MBx2
LCD Display
•
Video &
Graphics
•
Hard Drive
•
Optical Drive
•
15.4” WXGA (1280 x 800; 16:10) TFT LCD
display (185nit/glare 220nit)
Graphic controller: ATi ® Mobile X300/X700,
X16 PCI Express, DX9 compliant
External video memory up to 64/128/256MB
flexible frame buffer DDR SDRAM memory
40GB, 2.5" 9.5mm height, ATA33/66/100 or
Serial ATA Dual support
DVD Dual (DVD+/-RW),
Processor
Operating
System
Compliance
•
81
AV Feature Built-in
•
TV Tuner
•
•
Remote Control
•
Pointing Device •
•
Application
Launch Key
•
LED Status
Indicator
•
Keyboard
•
Interface Ports
•
•
•
PCMCIA
•
Audio
•
•
AC Adapter
Battery
•
•
•
Battery Charge
•
•
Battery Life
•
BIOS
•
82
Mini PCI TV Tuner w/ Coaxial connector,
support PAL, NTSC, SECAM
Support capture function to record the TV
programs into Hard Disk
Multi-function remote control to enjoy TV
program
Power on the system, Play TV, DVD play,
Music
Synaptics touchpad with 4 way scrolling button
E-mail, Internet, WLAN, TV, DVD hot keys
Power, Suspend/Resume, Battery charging
status, WLAN status, Hard Disk Access,
NumLock mode, CapsLock mode, Scroll Lock
mode
3.0mm travel, inverted-T, 88 keys with
windows key
Left – PCMCIA slot, 4 in 1 Card Reader, 1394
(Mini Jack)
Right – VGA connector, TV out connector,
LAN port, Modem port, USB 2.0 port*2,
Coaxial SPDIF out, Mic-in
Rear – USB 2.0 port*2, TV-in connector
(cable), MCE port
One Type II PCMCIA slot, support CardBus
AC’97 2.2, SPDIF out, 5.1 channel support
Built-in two high quality stereo speakers on
sides of K/B
Input: 100-240V AC, 50-60Hz, 1.5A, Universal
Output: 19V DC, 4.74A, 90W
8 cell Li-Ion battery pack
3.5 hrs charge time to 100% capacity while
system off (TBD)
4 hrs charge time to 100% capacity while
system on (TBD)
More than 2 hours by 8 cell Li-Ion battery pack
AMI, Support PnP, password, Bootable from
USB Disk
Card Reader
•
Communication
•
•
•
•
•
USB Disk
4 in 1 Card Reader (SD/MS/MS Pro/MMC
card)
10/100/1000Mbps Gigabit Ethernet on board
Intel® PRO/Wireless 2915ABG (802.11a/b/g)
network connection
TV-Turner Mini-PCI interface, support
PAL/NTSC (optional)
MDC combo: V9.0/9.2 56Kbps Fax/Modem
Web CAM/CMOS sensor, 0.3 Mega pixel
resolution CMOS image (optional)
Four USB2.0 ports, up to 480Mbit/s
USB Connector
•
Power
Management
•
ACPI 2.0 compliance, Support Stand-by,
Suspend to Disk, Suspend to RAM
Size
•
Weight
•
363.0(W) x 281.0(D) x 27.0(H) mm/30.0 mm
(front/back)
3 kg with 15.4” panel, Li-Ion battery and
Optical drive installed
Accessories
Packing
•
Factory Option
•
•
Quick Guide, Support CD (Driver, Utility,
Manual), AC Adapter, Power Cord, Battery
Pack
TV-Turner Mini-PCI interface, support
PAL/NTSC
Intel® PRO/Wireless 915ABG network
connection
802.11a/802.11b/802.11g WLAN
•
MDC combo: V9.0/9.2 56Kbps Fax/Modem
•
Web CAM/CMOS sensor, 0.3 Mega pixel
resolution CMOS image
Optical Device: CD-ROM, DVD-ROM, Combo
Drive (DVD-ROM+CD-RW), DVD Dual
(DVD+/-RW)
DVD Multi (DVD-RW+DVD-RAM), DVD Super
Multi (DVD+/-RW+DVD-RAM)
Bootable external USB1.1 FDD
•
•
•
•
83
Spec subject to change without notice
Battery life will vary depending on your specific hardware and
software configuration
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE: FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body. To maintain compliance with FCC RF exposure
compliance requirements, please avoid direct contact to the transmitting antenna during
transmitting. For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor
environment, and the antenna of this device must be integral.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
ECS declares that the 600 (FCC ID: SA66000IABG) is limited in CH1~CH11 by specified
firmware controlled in the USA.
84

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Print, Copy, Fill forms, Extract, Assemble, Print high-res
Modify Date                     : 2005:05:05 16:36:55+08:00
Create Date                     : 2005:05:05 16:36:33+08:00
Title                           : 600 _E_ V1.doc
Author                          : Cathy
Creator                         : 600 (E) V1 - Microsoft Word
Producer                        : Acrobat PDFWriter 5.0 for Windows NT
Page Count                      : 32
Mod Date                        : 2005:05:05 16:36:55+08:00
Creation Date                   : 2005:05:05 16:36:33+08:00
Metadata Date                   : 2005:05:05 16:36:55+08:00
Has XFA                         : No

EXIF Metadata provided by EXIF.tools