EM Microelectronic Marin EMBC01 Blue tooth low energy proximity beacon User Manual 7788

Download:
Mirror Download [FCC.gov]
Document ID	2440189
Application ID	RlWEnoFZPsiug+VOumbWlA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.57kB (632074 bits)
Date Submitted	2014-11-10 00:00:00
Date Available	2014-11-10 00:00:00
Creation Date	2014-09-30 14:53:51
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-09-30 14:53:51
Document Title	7788
Document Creator	Microsoft® Word 2010
Document Author:	mbe

EM MICROELECTRONIC - MARIN SA
PRELIMINARY
DRAFT A
PRODUCT USER MANUAL
EMBC01
TABLE OF CONTENTS
1.
2.
3.
4.
5.
PURPOSE ..........................................................................................................................................................2
USER INSTRUCTIONS......................................................................................................................................3
2.1. STATE MACHINE DEFINITION ....................................................................................................................3
BATTERY REPLACEMENT INSTRUCTIONS ..................................................................................................4
FCC & IC AUTHORIZATION .............................................................................................................................5
CE AUTHORIZATION ........................................................................................................................................5
This document is the property of EM MICROELECTRONIC-MARIN SA upon the condition that all rights originating in the information, whether patented or not, will be
respected.
EMBC01 User Manual v0.1 September-2014
PRELIMINARY
DRAFT A
1. PURPOSE
This is the product user manual. It contains FCC/CE/IC information, battery replacement instructions and a general
user’s guide.
This document is the property of EM MICROELECTRONIC-MARIN SA upon the condition that all rights originating in the information, whether patented or not, will be
respected.
EMBC01 User Manual v0.1 September-2014
PRELIMINARY
DRAFT A
2. USER INSTRUCTIONS
EMBC01 is a Bluetooth low-energy proximity beacon. It is controlled by a push button switch operated by pressing
on the center section of the coin like disc. Two LEDs, one red and one green will flash to indicate the state that the
beacon is in according to the state machine description given below. The standard firmware provided with each
beacon is V2.5.0, and implements the state machine described below, other state machines and beacon
operations can be defined by reprogramming the EMBC01.
2.1. STATE MACHINE DEFINITION
The state-diagram for the EMBC01 is shown in Figure 1. The firmware implements the following modes:
 Self-test
 Sleep-mode
 ID Short Range Mode
 ID Medium Range Mode
 ID Long Range Mode
 Lock Mode
Upon insertion of the battery, a self-test is performed, and the EMBC01 then enters a low-power sleep mode. On
subsequent short button presses (less than 2 seconds), the green LED flashes once and iterates through ID Short
Range Mode, ID Medium Range Mode, and ID Long Range Mode. On the next short button press, the red LED
flashes once and then the EMBC01 enters the low power sleep mode again. Subsequent short presses iterates
through these four modes again. In any state, if a long button press is performed (longer than 2 seconds), the
green LED will flash twice and the EMBC01 will stay in that mode until the end of battery life.
Figure 1: EMBC01 State-Diagram
This document is the property of EM MICROELECTRONIC-MARIN SA upon the condition that all rights originating in the information, whether patented or not, will be
respected.
EMBC01 User Manual v0.1 September-2014
PRELIMINARY
DRAFT A
3. BATTERY REPLACEMENT INSTRUCTIONS
The EMBC01 is powered by a single CR2032 battery. When the beacon stops functioning the battery will
need to be replaced. The step-by-step sequence to replace the expired battery with a fresh one is given in
the steps below.
Step 1: Open the beacon housing. Grasp the unit by the edges and pry the top off, exposing the circuit
board, battery and battery holder.
Step 2: Remove the battery. Slide the battery out from the holder.
Step 3: Replace the battery with a new Renata CR2032 Lithium 3V battery. Reverse the sequence in step2
above. Care must be taken to insert with a slight downward pressure so as not to damage the metal dome
switch that is located under the battery. On initial battery insertion both the red and green LEDs will flash
momentarily to indicate the start-up diagnostics have been completed successfully.
Step 4: Reassemble the case making sure the top is securely positioned around the bottom housing.
This document is the property of EM MICROELECTRONIC-MARIN SA upon the condition that all rights originating in the information, whether patented or not, will be
respected.
EMBC01 User Manual v0.1 September-2014
PRELIMINARY
DRAFT A
4. FCC & IC AUTHORIZATION
This device complies with FCC Part 15 and Industry Canada license exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement
This device complies with Health Canada’s Safety Code. The installer of this device should ensure that RF
radiation is not emitted in excess of the Health Canada’s requirement.
Cet appareil est conforme avec Santé Canada Code de sécurité 6. Le programme d’installation de cet appareil
doit s’assurer que les rayonnements RF n’est pas émis au-delà de I ’exigence de Santé Canada.
“Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.”
"Les changements ou modifications non expressément approuvés par la partie responsable de la conformité
pourraient annuler l'autorité de l'utilisateur à utiliser cet équipement."
5. CE AUTHORIZATION
Hereby, EM Microelectronic – Marin SA, declares that this EMBC01 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Par la présente EM Microelectronic – Marin SA déclare que l'appareil EMBC01 est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
The complete Declaration of Conformity can be found at
http://www.emmicroelectronic.com/products/wireless-rf
This document is the property of EM MICROELECTRONIC-MARIN SA upon the condition that all rights originating in the information, whether patented or not, will be
respected.
EMBC01 User Manual v0.1 September-2014

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
Language                        : en-US
Tagged PDF                      : Yes
Title                           : 7788
Author                          : mbe
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:09:30 14:53:51-06:00
Modify Date                     : 2014:09:30 14:53:51-06:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools