EMS Technologies 0B2L2C1900 MULTIMODE PCS SIGNAL ENHANCER User Manual 03 0089 Revised Manual
EMS Technologies MULTIMODE PCS SIGNAL ENHANCER 03 0089 Revised Manual
users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 386171 |
| Application ID | bixxjIHyYCiVLc9SvcBoOg== |
| Document Description | users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 57.58kB (719754 bits) |
| Date Submitted | 2004-01-05 00:00:00 |
| Date Available | 2003-12-30 00:00:00 |
| Creation Date | 2003-07-23 14:18:27 |
| Producing Software | Acrobat Distiller 5.0.5 (Windows) |
| Document Lastmod | 2003-07-23 10:19:13 |
| Document Title | Microsoft Word - 03-0089 Revised Manual.doc |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | Sam Wismer |
Type Acceptance Test Report Multimode PCS Repeater FCC Rule Parts: 2, 15 & 24 ACS Report Number: 03-0089-24TA Manufacturer: EMS Wireless Model: Link2Cell Installation Guide 5015 B.U. Bowman Drive Buford, GA 30518 USA Voice: 770-831-8048 Fax: 770-831-8598 Link2Cell™-19 SOHO Signal Enhancer Small Office – Home Office SIGNAL ENHANCER OPERATOR’S MANUAL 2850 Colonnades Court NW Norcross, GA 30071 Phone: 770-582-0555 Fax: 770-729-0075 Email: www.emswireless.com Preliminary Document Confidential EMS Wireless Disclaimer Every attempt has been made to make this material complete, accurate, and up-to-date. Users are cautioned, however, that EMS Wireless reserves the right to make changes without notice and shall not be responsible for any damages, including consequential, caused by reliance on the material presented, including, but not limited to, typographical, arithmetical, or listing errors. Copyright Information © EMS Wireless EMS Wireless Norcross, Georgia Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless WARNINGS, CAUTIONS, AND GENERAL NOTES This product conforms to FCC Part 15. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • • • • Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.” In accordance with FCC regulations regarding human exposure to radiofrequency energy, this device shall be installed such that a minimum separation distance of 20cm is maintained between it and general population. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other transmitter. This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareillage numérique de la classe B répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. L'opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l'interférence nocive, et (2) ce dispositif doit accepter n'importe quelle interférence reçue, y compris l'interférence qui peut causer l'opération peu désirée. Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless Safety Considerations When installing or using this product, observe all safety precautions during handling and operation. Failure to comply with the following general safety precautions and with specific precautions described elsewhere in this manual violates the safety standards of the design, manufacture, and intended use of this product. EMS Wireless assumes no liability for the customer's failure to comply with these precautions. WARNING WARNING Calls attention to a procedure or practice, which if ignored, may result in damage to the system or system component. Do not perform any procedure preceded by a WARNING until described conditions are fully understood and met. If You Need Help If you need additional copies of this manual, or have questions about system options, or need help with installation and using of the system, please contact EMS Wireless’ Sales Department. EMS Wireless Sales Dept. 2850 Colonnades Court NW, Norcross, GA 30071 Tel: 770 582 0555 Extension 5310 Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless Service Do not attempt to modify or service any part of this product other than in accordance with procedures outlined in this Operator's Manual. If the product does not meet its warranted specifications, or if a problem is encountered that requires service, notify EMS Wireless’ sales department. Service will be rendered according the EMS Wireless’ warranty and repair policy. The product shall not be returned without contacting EMS Wireless and obtaining a return authorization number from the Sales department When returning a product for service, include the following information: Owner, Model Number, Serial Number, Return Authorization Number (obtained in advance from EMS Wireless Customer Service Department), service required and/or a description of the problem encountered. The EMS Wireless Quality Plan includes product test and inspection operations to verify the quality and reliability of our products. EMS Wireless uses every reasonable precaution to ensure that every device meets published electrical, optical, and mechanical specifications prior to shipment. Customers are asked to advise their incoming inspection, assembly, and test personnel as to the precautions required in handling and testing ESD sensitive components. Physical damage to the external surfaces voids warranty. These products are covered by the following warranties: 1. General Warranty EMS Wireless warrants to the original purchaser all standard products sold by EMS Wireless to be free of defects in material and workmanship for the duration of the warranty period of one (1) year from date of shipment from EMS Wireless. During the warranty period, EMS Wireless’ obligation, at our option, is limited to repair or replacement of any product that EMS Wireless proves to be defective. This warranty does not apply to any product, which has been subject to alteration, abuse, improper installation or application, accident, electrical or environmental over-stress, negligence in use, storage, transportation or handling. 2. Specific Product Warranty Instructions All EMS Wireless products are manufactured to high quality standards and are warranted against defects in workmanship, materials and construction, and to no further extent. Any claim for repair or replacement of a device found to be defective on incoming inspection by a customer must be made within 30 days of receipt of the shipment, or within 30 days of discovery of a defect within the warranty period. This warranty is the only warranty made by EMS Wireless and is in lieu of all other warranties, expressed or implied, except as to title, and can be amended only by a written instrument signed by an officer of EMS Wireless. EMS Wireless sales agents or representatives are not authorized to make commitments on warranty returns. In the event that it is necessary to return any product against the above warranty, the following procedure shall be followed: Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless a. Return authorization shall be received from the EMS Wireless Customer Service prior to returning any device. Advise the EMS Wireless Customer Service of the model, serial number, and the discrepancy. The device shall then be forwarded to EMS Wireless, transportation prepaid. Devices returned freight collect or without authorization may not be accepted. b. Prior to repair, EMS Wireless Customer Service will advise the customer of EMS Wireless test results and will advise the customer of any charges for repair (usually for customer caused problems or out-of-warranty conditions). If returned devices meet full specifications and do not require repair, or if non-warranty repairs are not authorized by the customer, the device may be subject to a standard evaluation charge. Customer approval for the repair and any associated costs will be the authority to begin the repair at EMS Wireless. Customer approval is also necessary for any removal of certain parts, such as connectors, which may be necessary for EMS Wireless testing or repair. c. 3. Repaired products are warranted for the balance of the original warranty period, or at least 90 days from date of shipment. Limitations of Liabilities EMS Wireless’ liability on any claim of any kind, including negligence, for any loss or damage arising from, connected with, or resulting from the purchase order, contract, or quotation, or from the performance or breach thereof, or from the design, manufacture, sale, delivery, installation, inspection, operation or use of any equipment covered by or furnished under this contract, shall in no case exceed the purchase price of the device which gives rise to the claim. EXCEPT AS EXPRESSLY PROVIDED HEREIN, EMS WIRELESSMAKES NO WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED, WITH RESPECT TO ANY GOODS, PARTS AND SERVICES PROVIDED IN CONNECTION WITH THIS AGREEMENT INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. EMS WIRELESSSHALL NOT BE LIABLE FOR ANY OTHER DAMAGE INCLUDING, BUT NOT LIMITED TO, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH FURNISHING OF GOODS, PARTS AND SERVICE HEREUNDER, OR THE PERFORMANCE, USE OF, OR INABILITY TO USE THE GOODS, PARTS AND SERVICE. EMS Wireless test reports or data indicating mean-time-to-failure, mean-timebetween-failure, or other reliability data are design guides and are not intended to imply that individual products or samples of products will achieve the same results. These numbers are to be used as management and engineering tools, and are not necessarily indicative of expected field operation. These numbers assume a mature design, good parts, and no degradation of reliability due to manufacturing procedures and processes. Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless Handling the Link2Cell™ -19 1. Use ESD precautions when dealing with the modules within the Link2Cell™ -19 so that units are not damaged. 2. Opening the unit voids warranty. 3. Disconnecting any component within the Link2Cell™-19 when powered can damage or destroy the equipment and will void the warranty. Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless Link2Cell™-19 Manual Description The Link2Cell™-19 SOHO, (Small Office-Home Office) Signal Enhancer, is a PCS band, bidirectional amplifier unit and was designed to provide enhanced RF coverage for wireless systems in small facilities. Usage includes providing coverage in retail stores, offices, warehouses, restaurants, homes, etc. The Link2Cell™-19 is housed in an indoor mountable enclosure, and is powered with a regulated wall mountable power supply. The Link2Cell™-19 supports all system protocols including CDMA, GSM/PCS1900 and TDMA and a single model will cover all licensed 1.9 GHz PCS bands A through F. The Link2Cell™-19 features Auto set-up, lightweight compact enclosure with internal antennas, local alarming, and excellent electrical specifications, high reliability with cost effective pricing. Functionality The Link2Cell™-19 is capable of automatically adjusting its own signal gain levels up to the maximum output power levels. The Link2Cell™-19 detects the downlink output power and adjusts the level for 2 dBm composite output power and continues to monitor and reset the gain as required for proper system performance. For example, when CDMA protocol system is being amplified, there could be an error in set up initially resulting from only pilot sync, and paging Walsh codes being present on the RF carrier. The Link2Cell™-19 will reduce the system gain until no signal is received that will exceed the output power setting. This prevents the Link2Cell™-19 from setting up to a higher in power level than actually desired if all of the Walsh codes were present. The gain does not continually change to maintain an output power of 2 dBm AGC (Automatic Gain Control) since this would defeat the benefits of power control in the service providers system. The Link2Cell™ has 40 dB of gain control in the uplink and downlink signal paths. This gain is controlled by a microprocessor that monitors the system operation on a real time basis. The uplink and downlink attenuators are controlled by the internal microprocessor to adjust for maximum gain in both paths. The uplink and dowlink signal paths are adjusted to the same setting by the microprocessor unless the system determines this is not optimum for the units operation. Alarming Alarming monitoring is accomplished in the Link2Cell™ by the microprocessor, which will detect a failure in gain or a system oscillation. This is indicated to the user by a solid constant Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless Red indicator. User can try recycling the power which will allow the unit to go thru its automatic set up operation but if the problem persists contact your service provider. Indicators The Link2Cell™-19 is equipped with three LED indicators on the end of the unit which provide the following information: During normal operation: Indicator Green Red State Description Off Solid Indication Flashing Indication No DC Input Power Applied DC Power on, normal function System Initialization, Auto Set Up Flashing Indication Warning, fault condition (Unit will reset gain to stable operation) Alarm (Contact your Service Provider) Solid Indication Amber Flashing Indication No RF Signal Detected (<-90 dBm) Solid Indication Weak RF Signal (>-85 dBm) Initial System Automatic Set Up: (First 2-3 minutes of DC power being applied) Indicator State Description Green Flashing Indicator System Initialization, Auto Set Up Amber/Red Solid On, Both >76 dB Gain Amber Solid On Indication >73 dB Gain Red Solid On Indication >70 dB Gain Amber/Red Flashing Both >67 dB Gain Amber/Red Off, both <64 dB Gain *Green Indicator will go to a solid indication once the initial set up is complete. Link2CellTM-19 Manual Preliminary Document Confidential EMS Wireless Primary Power The Link2Cell™ Unit operates on 9 VDC input power @ 1 Amp. This is supplied with a regulated wall mount supply, which is UL, and CSA listed. These are available to operate on AC input voltage of 115 VAC. Donor/Server Antenna Internal donor and server antenna are each 13 dB nominal gain. The donor antenna must be orientated to point in the direction of the Service Providers cell site location. Beam width of the antennas is approximately 60 degrees wide so it is necessary for the antenna to point toward the cell site. The indicators will provide a reference of the strongest RF power strength when the antenna is located in the optimum location. Link2CellTM-19 Manual 10 Preliminary Document Confidential EMS Wireless Installation: Note 1: The user is cautioned that modification or changes to this device not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. Note 2: Manufacturer’s rated composite output power, individual channel power will vary depending on the number of channels and distance from each cell site being received Note 3: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. Introduction Link2Cell™-19 is quick and easy to install, using a set of common tools. This section will provide the basic steps to performing the installation of Link2Cell™ . Please read complete instructions before beginning assembly. Placement of the Unit Unit must be positioned with the donor antenna facing the direction of the cell site and the opposite side of the unit with LED indicators facing the intended coverage area. Signal strength at this location should be adequate to make a call with the subscriber unit for the SOHO, (Small Office-Home Office) signal enhancer to provide additional coverage and service in the facility. (See optional mounting configurations in figure 2.) The signal enhancer provides improved signal performance by amplifying radio frequency signals being received from the base station and the subscriber unit (mobile phone). The model Link2Cell™ provides signal enhancement for the entire PCS band only, see the Link2Cell specifications for details on equipment. Link2Cell™ is designed to automatically set up its own gain and will improve performance in most applications as long as a signal is received at the window location. Actual area of coverage that will be improved will vary depending on the signal level received, and blockage to the signals in the desired area of coverage. Blockages to RF signals include walls, people, equipment and furniture, etc. Amount of signal attenuation by each of these blockages will vary depending upon their size and composition. If additional area of coverage is required, additional Link2Cell™ units can be cascaded inside of the facility to provide this. There is a practical limit to the number of signal enhancers that can be cascaded and provide enhanced system performance. If greater than three total Link2Cell units are required you should call your system provider for additional solutions that are available. Link2CellTM-19 Manual 11 Preliminary Document Confidential EMS Wireless Getting Started: Unpack all of the boxes and insure all of the material is included for your installation requirements and undamaged in shipment. Quantity Part Description Link2Cell™ SOHO Signal Enhancer Loctite Thread locker Power Converter Mounting Base Mounting Posts Wall Anchors Mounting Screws Link2Cell Repeater LOCTITE Threadlocker Power Converter Mounting Base Mounting Posts (2) Wall Anchors (4) Mounting Screws (4) Figure 1 Package Contents Link2CellTM-19 Manual 12 Preliminary Document Confidential EMS Wireless Link2Cell™-19 Unit Orientation & Installation Link2Cell™ is designed for optimum use as an in-door signal enhancer. The housing is not weather resistant and the automatic set up procedure assumes sufficient isolation between antennas. Since the Link2Cell™ has a total of 53 dB active gain and an isolation of 73 dB must be obtained between the internal donor and the server antenna. Should adequate isolation not be obtained the unit will automatically reduce its gain until adequate isolation is obtained for the unit to operate properly. Isolation between the antennas is reduced by several conditions near or around the antennas, metal or conductive material, and movement of people near the antennas. Mounting the Link2Cell™-19 Link2Cell™-19 must be mounted so the Donor antenna is orientated to receive and transmit to the cell site. The Donor antenna is located on the opposite side of the unit of the LED indicators of the Link2Cell™-19 with the LED’s either at the bottom or the top to keep the orientation of the Donor antenna correct with respect to the direction of the cell site and which wall you desire to mount the unit on. 9 VDC input is located on the side of the Link2Cell™19 housing shown above. The Link2Cell™-19 may also sit on top of a book case, cabinet or on the floor as long as adequate signal is received by the unit to provide the desired coverage enhancement. As was previously discussed, these cabinets and bookcases should not be metal since this will effect the performance of the unit. OR OR Plug Power Converter into Unit Plug Power Converter into 110V Outlet Vertical Mounting Surfaces Horizontal Mounting Surfaces Figure 2 Optional Mounting Configurations Link2CellTM-19 Manual 13 Preliminary Document Confidential EMS Wireless -Select the window that provides the strongest signal strength from the cell site to your portable phone by viewing the number of bars displayed on the face of the phone. - Select the location in the window that provides the strongest signal strength from the cell site to your portable phone which will indicate how to position the Link2Cell™ (donor antenna) signal enhancer unit -Remove the 2 protective caps of the mounting holes from the selected side of the Link2Cell™, taking into consideration the 3 LED’s must be facing you or the desired area of coverage. Remove Protective Caps from Mounting Holes -Apply Loctite to the threads of the mounting posts and install (hand tighten only) into the open mounting holes of Link2Cell™ unit. Apply LOCTITE to Threads of Mounting Posts in Accordance with Manufacturers Instructions and Install into Link2Cell Unit. Hand-Tighten Only Link2CellTM-19 Manual 14 Preliminary Document Confidential EMS Wireless -Attach Mounting Base (with the open U potion in an upward ? position) to the selected position mounting surface area using the appropriate mounting hardware, (4 Wall anchors and 4 mounting screws). Slide Link2Cell Unit into Mounting Base Attach Mounting Base to Mounting Surface Using Appropriate Mounting Hardware -In a downward ? sliding motion, hook the Link2Cell™ Unit onto the secured mounting base. -Connect the Power Converter into the Link2Cell™ unit and the plug power converter into an 110V outlet. Plug Power Converter into Unit Plug Power Converter into 110V Outlet Link2CellTM-19 Manual 15 Preliminary Document Confidential EMS Wireless IMPORTANT: Before performing any maintenance or changing the position or location of the unit, make sure power plug is removed from the 110 AC wall socket. Once the unit is repositioned, the power should be plugged into the 110 wall socket, this will insure the unit is set to maximum gain and performance. System Set Up Instructions: -After installing unit, apply power and Link2Cell™ unit will automatically set up. The system initialization will require 1 – 2 minutes for setup completion. -Note: Since the Link2Cell™ is a broadband unit, it will improve the service for all system providers with cell sites in the direction the donor antenna is positioned. Specifications for Model: Link2Cell™-19 Downlink Operating Frequency, Uplink Operating Frequency, Downlink EIRP Transmit Power Uplink EIRP Transmit Power System Gain Gain Flatness Noise Figure Spurious Output @ Rated Power FCC Regulations @Fc +/− 885 KHz (CDMA only) @Fc +/− 1.25 MHz 2 tone @ -1 dBm each, DL 1 dB Compression IP3 Operating Temperature, degrees Power Source: Mechanical Dimensions, H x W x D, MTBF Indicators, Green LED Red LED MHz MHz dBm dBm dB dB dB 1930 to 1990 1850 to 1910 15 28 40 to 79 +/− 2 ≤6 dB dBc dBc dBc dBm dBm ≤ -13 ≤ 45 ≤ 26 ≤ 60 UL 22, DL 22 UL 41, DL 41 0° to +50° (115 VAC) 9 VDC@ 1 amp, External AC to DC 14.25 x 14.25 x 6.0 80,000 Solid, Normal Operation Flashing, Signal Overdrive Solid, Auto Off, Contact Service Provider Flashing, No Signal Detected, ≤ 90 dB Solid, Weak Signal, ≤ 85 dB Upon Power Up Green, Flashing during set up Amber/Red ≥ 76 dB Solid Amber ≥ 73 dB Solid Red ≥ 70 dB Solid Amber/Red ≥ 67 dB Flashing Both OFF = 64 dB FCC, UL, CSA inches hours Yellow LED Automatic System Set Up System Gain Indications upon Power Up For first 3 minutes Certifications, *Meets or exceeds the EIA/TIA system requirements for CDMA, TDMA or GSM system protocols. Link2CellTM-19 Manual 16 Preliminary Document Confidential EMS Wireless Trouble Shooting: The Link2Cell™-19 has no field replaceable parts; repair is limited to improper mounting location with respect to the cell site, insufficient RF signal levels, and installation or defective units. Problem No Power Check Power Source Power Source OK Alarm Indication Amber Flashing Amber Solid Indicator No change No RF signal Detected No Change No Change Weak RF Signal Weak RF Signal No Change Green Flashing Indication No signal improvement to subscriber unit Recycle power to unit Gain Settings, Amber or Amber/red Red, amber/red solid or flashing, or off No Change Corrective Action Reconnect or repair Replace Unit Recycle AC Power Replace Unit Recycle AC Power Check Antenna alignment with cell site Replace Unit New Installation, Check Antenna alignment with cell site and recycle power Previously working, recycle power. Replace Unit Unit is in initial system initialization, if still flashing after 5 minutes replace unit Watch indicators for gain settings. OK, check antenna alignment with cell site. Insufficient isolation between antennas in the unit possibly. Move unit and try again. Unit operation can be effected if placed to close to metal objects or equipment. Consult your Service Provider For Customer Service Call, Tel: 770 583-0555 Extension 5310 Link2CellTM-19 Manual 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:07:23 14:18:27Z Modify Date : 2003:07:23 10:19:13-04:00 Page Count : 18 Creation Date : 2003:07:23 14:18:27Z Mod Date : 2003:07:23 10:19:13-04:00 Producer : Acrobat Distiller 5.0.5 (Windows) Author : Sam Wismer Metadata Date : 2003:07:23 10:19:13-04:00 Creator : Sam Wismer Title : Microsoft Word - 03-0089 Revised Manual.docEXIF Metadata provided by EXIF.tools