ES Gear GSM-EXP GSM / GPRS expansion module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3515141
Application ID	4quMshtBzQRmzsA2N+VtJg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.62kB (145277 bits)
Date Submitted	2017-08-17 00:00:00
Date Available	2017-08-17 00:00:00
Creation Date	2017-07-21 20:37:38
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2017-08-04 19:25:02
Document Title	Microsoft Word - 1. PRODUCT MANUAL GSM for FCC June'2017
Document Creator	PScript5.dll Version 5.2.2
Document Author:	Administrator

PRODUCT MANUAL
Product name: GSM / GPRS Module
June, 2017
I. Description
The Industruino GSM / GPRS expansion module adds remote internet connectivity and SMS control to any
Industruino IND.I/O or Industruino PROTO.
The features include:






Connect to the internet via GPRS
Send/Receive SMS messages
Micro-SD card slot (up to 2GB)
RS-232 port + 14P IDC port
DIN-rail mountable
Fully enclosed
The module supports three installation modes:



Power+Data via IDC connector. Primary UART connected to GSM functions, secondary UART connected to
RS232 interface.
Power+Data via IDC connector. Secondary UART connected to GSM functions, prinary UART connected to
RS232 interface.
Power via external 2-pin connector, data via RS232 interface. In this mode the module functions as a
standard GSM/GPRS modem, allowing you to test commands via a PC.
II. Operation instructions
Before using the Industruino kit, please read the manual carefully and pay full attention to safety to handle the
product correctly.
For the latest instructions regarding installation, usage and operation of the Industruino kit please visit:
www.industruino.com/support
Safety Instructions
WARNINGS:
• Do not connect any part of the device to voltages higher than 32V.
• Always switch off power before you connect or disconnect an external device or accessory.
• Avoid circuit or wire exposure. Do not touch exposed connections or components when the device is powered
on or when devices connected to it are powered on.
• Use only with cables and accessories that are approved or recommended by Industruino.
• Do not operate with suspected failures. If suspected damage occurs with the device, have it inspected by
qualified service personnel before further operations.
• Do not operate in an explosive atmosphere.
• Do not use in wet/damp conditions.
• Keep device surfaces clean and dry.
• Use only for applications described in the catalog and the manual, and only with third party devices or
components if they have been approved or recommended by Industruino.
• The device can only function correctly and safely if it is transported, stored, set up, and installed correctly, and
operated and maintained as recommended.
• The device must be installed and wired by a trained technician following the applicable local safety standards
and regulations.
Conditions of use
(1) Industruino GSM / GPRS module (“the PRODUCT”) shall be used in conditions;
i) where any problem, fault or failure occurring in the PRODUCT, if any, shall not lead to any major or serious accident;
and
ii) where the backup and fail-safe function are systematically or automatically provided outside of the PRODUCT for the
case of any problem, fault or failure occurring in the PRODUCT.
(2) The PRODUCT has been designed and manufactured for the purpose of being used in general industries.
ES GEAR LTD. OR ITS DISTRIBUTORS SHALL HAVE NO RESPONSIBILITY OR LIABILITY (INCLUDING, BUT NOT
LIMITED TO ANY AND ALL RESPONSIBILITY OR LIABILITY BASED ON CONTRACT, WARRANTY, TORT, PRODUCT
LIABILITY) FOR ANY INJURY OR DEATH TO PERSONS OR LOSS OR DAMAGE TO PROPERTY CAUSED BY the
PRODUCT THAT ARE OPERATED OR USED IN APPLICATION NOT INTENDED OR EXCLUDED BY INSTRUCTIONS,
PRECAUTIONS, OR WARNING CONTAINED IN ES GEAR LTD. OR ITS DISTRIBUTORS’ USER, INSTRUCTION
AND/OR SAFETY MANUALS, TECHNICAL BULLETINS AND GUIDELINES FOR the PRODUCT.
(“Prohibited Application”)
Prohibited
Applications
the PRODUCT in;
include,
but
not
limited
to,
the
use
of
Nuclear Power Plants and any other power plants operated by Power companies, and/or any other cases in which the
public could be affected if any problem or fault occurs in the PRODUCT.
Railway companies or Public service purposes, and/or any other cases in which establishment of a special quality
assurance system is required by the Purchaser or End User.
Aircraft or Aerospace, Medical applications, Train equipment, transport equipment such as Elevator and Escalator,
Incineration and Fuel devices, Vehicles, Manned transportation, Equipment for Recreation and Amusement, and Safety
devices, handling of Nuclear or Hazardous Materials or Chemicals, Mining and Drilling, and/or other applications where
there is a significant risk of injury to the public or property.
Notwithstanding the above, restrictions ES Gear Ltd. may in its sole discretion, authorize use of the PRODUCT in one or
more of the Prohibited Applications, provided that the usage of the PRODUCT is limited only for the specific applications
agreed to by ES Gear Ltd. and provided further that no special quality assurance or fail-safe, redundant or other safety
features which exceed the general specifications of the PRODUCTs are required. For details, please contact an ES Gear
Ltd. representative.
III. Regulatory
CE Compliance
This product meets the essential requirements of applicable European Directives as follows:
Directive 2014/53/EU; Radio Equipment Directive (RED)
2011/65/EU; Restriction of Hazardous Substances Directive (RoHS).
WEEE Compliance
All Industruino products that are subject to the WEEE directive shipped from
the WEEE marking requirement.
September 1, 2014 are compliant with
Such products are marked with the “crossed-out wheelie bin’’ WEEE symbol (shown, above) in accordance with European
Standard EN50419.
IV. Mode Guidance
IDC mode 1:
• SIM800 module connected to second UART (“Serial1” on D21G, Software serial D5/D10 on 32u4).
• SIM800 power on/off controlled using pin “D6”.
• SIM800 “ring indicator” connected to pin “D7”.
• RS232 interface connected to first UART
(“Serial” on D21G, “Serial1” on 32u4/1286).
• Module powered from IDC connector.
IDC mode 2:
• SIM800 module connected to first UART
(“Serial” on D21G, “Serial1” on 32u4/1286).
• SIM800 power on/off controlled using pin “D6”.
• SIM800 “ring indicator” connected to pin “D7”.
• RS232 interface connected to second UART (“Serial1” on D21G, Software serial D5/D10 on 32u4).
• Module powered from IDC connector.
External mode:
• RS232 interface connector to SIM800.
• SIM800 power on/off controlled using RS232 “RTS” line.
• SIM800 “ring indicator” connected to RS232 “RI” line.
• Module powered from external power supply.
V. Programming Guide
This GSM/GPRS module is based on the SIMCOM SIM800H module, and is controlled with AT commands.
The AT commands can be issued via the RS-232 port or via the TTL UART ports on the 14pin IDC connector.
For an overview of supported AT commands please download the “SIM800 Series_AT Command Manual_V1.10” from
the SIMCOM website: http://simcomm2m.com/En/module/detail.aspx?id=75
For ease of use below is a list of Arduino libraries which wrap all AT commands in easy to use function:
• TinyGSM library
• Adafruit FONA library
• Freematics SIM800 library
VI. Packing List
The product comes with a cable to connect to Industruino control. Power is supplied either from 14 pin IDC cable or
separately as external Vin.
Micro SD and SIM card holders are accessed by opening the top shell of the enclosure.
6
Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the
condition that this device does not cause harmful interference.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Administrator
Create Date                     : 2017:07:21 20:37:38+08:00
Modify Date                     : 2017:08:04 19:25:02+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2017:08:04 19:25:02+08:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - 1. PRODUCT MANUAL GSM for FCC June'2017
Creator                         : Administrator
Document ID                     : uuid:fc89109c-08cf-43e8-996f-0f1bd911ddcb
Instance ID                     : uuid:43ca209b-55c2-4f8a-b580-939d25888821
Page Count                      : 7

EXIF Metadata provided by EXIF.tools