EVOLIS 0030 RFID IDENTIFY THE RIBBON AND SET THE PARAMETERS User Manual UserGuide Badgy100200 EN 2
EVOLIS RFID IDENTIFY THE RIBBON AND SET THE PARAMETERS UserGuide Badgy100200 EN 2
EVOLIS >
User Manual
USER GUIDE
Evolis Card Printer © 201 All rights reserved. March 201.
Ref. KU-%'*1-0-ENG Rev. A0
Ev
Copyright
Evolis Card Printer © March 201. All rights reserved.
Copyright notice
Users must observe the copyright regulations applicable in their country. This manual must not be photocopied, translated, reproduced
or transmitted, in whole or in part, for any reason and by any electronic or mechanical means whatsoever without the express written
consent of the Evolis Card Printer company.
All the information contained in this document is subject to change without prior notice.
Evolis Card Printer cannot be held liable for any errors that may be found in this manual, or for any loss or damage arising accidentally or
as a result of dissemination or use of this manual.
Trademarks
, Evolis Premium Suite and Evolis High Trust are trademarks of Evolis Card Printer. All other trademarks belong to their respective
holders.
Warranty
Refer to the warranty notice supplied with your printer for warranty terms and conditions and limitations.
Environmental information
Evolis is committed to helping the environment by reducing the energy consumption of its products.
(YROLVSULQWHUVKDYHEHHQFHUWLÀHG(1(5*<67$5GXHWRWKHLUORZSRZHUFRQVXPSWLRQ
Recycling of end-of-life products
The manufacture of the equipment that you have purchased required the extraction and use of natural resources. It may contain
materials that are hazardous to health and the environment.
To prevent the dispersal of such materials into our environment and reduce the pressure on our natural resources, we recommend that
you use existing collection systems. These systems will appropriately re-use or recycle most of the materials in your end-of-life equipment.
The crossed-out dustbin symbol on your device is a reminder to use these systems.
If you need further information on collection, re-use and recycling systems, contact your local or regional waste management body.
'R QRW KHVLWDWH WR FRQWDFW XV WR ÀQG RXW PRUH E\ YLVLWLQJ RXU ZHEVLWH DW www.evolis.com or by emailing the following address:
info@evolis.com.
2
About your new printer
Thank you for choosing an Evolis printer.
Using your new printer, you will be able to create a wide variety of high-quality cards and badges which can be printed in various
thicknesses, colours and styles. This printer uses consumables and accessories available from Evolis. For further details, visit our website at
www.evolis.com.
Warranty registration
Please register on line at www.evolis.com to receive our special offers and general information.
Once on the website, click on Drivers and Support then on Register your printerDQGÀOOLQDOOWKHÀHOGVJLYLQJLQSDUWLFXODUWKHPRGHODQG
serial number found on your printer.
Getting started
The purpose of this user guide is to guide you, step by step, through your printer and how it works. Take some time to read it in order to
better understand your printer and its features, and to save time during installation and use.
$VZLWKDOO(YROLVSURGXFWVDJUHDWGHDORIFDUHKDVEHHQWDNHQRYHUWKLVPDQXDO6KRXOG\RXÀQGDQHUURUKRZHYHUSOHDVHOHWXVNQRZE\
emailing us at info@evolis.com.
Contents
The bookmarks found top left of your screen can be used to navigate between the various sections in this user guide.
Icons
The following icons are used in this manual to highlight important information:
Information providing further details or depth about certain points in the main text.
Indicates that failing to take the recommended action is liable to damage your printer.
This symbol indicates that a video showing the procedure is available on the www.evolis.com website and
clicking on it takes you straight to on-line help.
This symbol links to Evolis Print Center, accessible from your computer, which you can use to administer and
manage you printer and change its settings.
3
Getting started
1-1 Unpacking
<RXUSULQWHULVVXSSOLHGZLWKVHYHUDODFFHVVRULHVWKDWZHDVN\RXWRORRNDWFORVHO\
This list may vary depending on your location.
The printer is shipped in special packaging designed to prevent any damage in transit. If you notice any visible damage, do not hesitate
to contact the shipper and immediately inform your Evolis dealer, who will tell you the procedure to follow.
Evolis takes great care over the quality of its packaging and we ask that you keep this packaging somewhere clean and dry.
You will be asked for the full original packaging (outer box, inner wedges and protective bags) in the event that
the printer is returned. If the printer is returned without its original packaging and components are damaged in
transit, these components will no longer be covered by the warranty. You will be charged for new packaging
for shipping the printer back to you.
Accessories supplied with your printer:
Q
Q
Q
Q
Q
Power supply unit - SWITCHBOX Type F10723-ARU&:7W\SH.3/0.
Mains power cable.
USB cable.
Installation, documentation and software CD-ROM.
4XLFNLQVWDOODWLRQJXLGH
If any of these components is missing, please contact your Evolis dealer.
Use only the power supply unit supplied with your Evolis printer.
SWITCHBOX Type F10723-ARU&:7W\SH.3/0.
Use only the USB cable supplied with your Evolis printer.
The Evolis printer must be placed in a dry location, protected from dust and draughts but well-ventilated. Take
FDUHWRNHHS\RXUSULQWHURQDÁDWVWXUG\VXUIDFHDEOHWREHDULWVZHLJKW
4
1
A - Card input feeder
B - Output hopper
& - Control panel
' - USB connectors
( - Power cable socket
) - Kensington lock
1-2 Description of the printer and its functions
5
1
&DUGVDQG
ULEERQ
3ULQWHU
3XVKEXWWRQ
$FFHVV WR WKH VLGH SDQHOV RI WKH PDFKLQH DQG WKH RSWLRQ PRGXOH ÀWWLQJUHPRYDO DUHDV LV UHVWULFWHG WR \RXU
UHWDLOHULQVWDOOHURUWRH[SHULHQFHGXVHUV7KHPDFKLQHVKRXOGDOZD\VEHGLVFRQQHFWHGIURPWKHSRZHUVXSSO\
(unplugged) before carrying out any work on it.
Look at the getting started video described in the following section.
* - Thermal print head +- Serial number label
6
1
1-3 Installation
1-3a CONNECTING THE PRINTER
³ Connection to the power supply
The printer must be connected to a properly protected and earthed electrical installation.
FI: Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan.
NO: Apparatet må tilkoples jordet stikkontakt.
SE: Apparaten skall anslutas till jordat uttag.
Connect the power cable to the power supply unit, then plug the power supply unit
connector into the printer.
1H[WSOXJWKHHQGRIWKHSRZHUFDEOHLQWRDQHDUWKHGSRZHUVRFNHW
The printer is powered on: the control panel lights up showing the printer is working
properly. If the control panel does not light, then either installation has not been
carried out correctly or the printer is not working properly. Check the installation.
Before attempting any maintenance, ensure that the power cable is always unplugged. For your personal safety,
ensure that the cable and power supply unit remain easy to access, especially in the event of an emergency.
To save energy, the printer will automatically switch itself to standby mode after 10 minutes of inactivity. The printer
switches to hibernation mode after 30 minutes in standby mode.
7KHVWDQGE\WLPHVFDQEHFRQÀJXUHGLQWKH(YROLV3ULQW&HQWHU,QVWDQGDUGVWDQGE\PRGHVHQGLQJDSULQWUHTXHVW
UHVWDUWVWKHSULQWHUDQGTXLFNO\SUHVVLQJIRUVHFRQGRQWKHEXWWRQH[LWVWKHSULQWHUIURPKLEHUQDWLRQPRGH.
³ Connecting the USB cable
Under no circumstances should you connect the USB data cable before installation of the printer driver is
complete.
Refer to the section on printer driver installation for further details, and follow the instructions carefully.
7
1
1-3b RIBBONS
Evolis original High Trust ribbons optimise your printer’s operation and avoid causing damage to it. The use of ribbons from other suppliers
is liable to damage your printer and voids the manufacturer’s warranty for the printer.
For optimum print quality, Evolis recommends that the printer is fully cleaned every time the ribbon is changed. See the Servicing and
Maintenance section of this manual.
³ Fitting the ribbon
The printer automatically recognises the ribbon inserted.
Open the cover.
Insert the ribbon as shown.
Close the cover and press until a click is heard.
8
1
1-3c CARDS
)RURSWLPXPTXDOLW\WKHFDUGVXVHGPXVWEH,62FHUWLÀHG
Use only the card types recommended by Evolis.
'RQRWWRXFKWKHSULQWDEOHVXUIDFHRIWKHFDUGVLQRUGHUWRSUHVHUYHSULQWTXDOLW\
'RQRWXVHFDUGVWKDWKDYHEHHQGDPDJHGIROGHGHPERVVHGRUGURSSHGRQWKHÁRRU
Keep your cards protected from dust.
³ Loading the cards
Open the card feeder.
Insert the cards, a maximum of 50 cards of thickness 0.76 mm. Ensure the cards are positioned as illustrated in the diagram.
Close the feeder.
9
9
1
³ Removing printed cards
Once the print cycle is complete, cards are delivered into the output hopper below the card feeder. This output hopper is designed to
collect the printed and/or encoded cards. The printer is equipped with an output hopper with a maximum capacity of 20 x 0.76 mm
cards.
10
1
Printing
2-1 Installing the print driver
1HZDGYDQFHGIXQFWLRQVDXWRPDWHSULQWHUFRQÀJXUDWLRQDIWHUWKHSULQWGULYHUKDVEHHQLQVWDOOHG
<RXUSULQWHULVGHOLYHUHGZLWKD&'FRQWDLQLQJWKHSULQWGULYHUVIRU:LQGRZVDQG0DFLQWRVKSODWIRUPV
To install a print driver, insert the CD into your computer and select the print driver menu. A program will guide you through the entire
installation process.
Do not connect your USB cable to your computer until prompted to do so by the installation program.
For the connection procedure, see the section on Connecting the Printer.
)ROORZWKHLQVWDOODWLRQSURFHGXUHVFUXSXORXVO\$OOYHUVLRQVRI:LQGRZVDQG0DFLQWRVKUHTXLUHWKHXVHUWRKDYH
administrator rights to install the driver.
2
2-2 Managing the print settings
Once the ribbon has been installed, your Evolis printer will automatically adapt its parameters and settings to suit the ribbon.
$JUDSKLFDSSOLFDWLRQFDOOHG(YROLV3ULQW&HQWHULVDYDLODEOHWRKHOS\RXLIQHFHVVDU\WRFKDQJHFHUWDLQSUHGHÀQHGVHWWLQJV
To access this application:
QFrom the Start button on the bottom left of your screen in the Windows task bar, select All programs, Evolis Card Printer, Evolis Premium
Suite, Evolis Print Center
Q The application displays all connected Evolis printers.
2
Q Select the desired printer.
Q Right click the name of the printer, select Properties to access the settings or double (left) click the name of the printer.
3D\DWWHQWLRQWRWKHVHWWLQJVGHÀQHGXQGHUWKHSULQWGULYHU3URSHUWLHVDQGGRQRWKHVLWDWHWRFRQWDFW\RXU(YROLV
dealer for any advice and assistance needed before making any changes.
Please refer to the Evolis Print Center manual for more detail on the meanings of each of the settings.
2
1RWLÀFDWLRQRIPHVVDJHVDQGZDUQLQJV
The Evolis Printer Manager has an additional function allowing the printer to communicate with the user ZLWKQRWLÀFDWLRQV.
7KHUHDUHVHYHUDOW\SHVRIQRWLÀFDWLRQV
Q Messages about the maintenance of the printer.
Q Messages and alerts associated with the ribbons, their compatibility with your printer or the nature of your print requests.
Q Warnings about problems which have stopped the printer.
When the Evolis Printer Manager is active, a small icon is displayed in the bar on the bottom right of your screen.
The colour of the icon varies according to the status of the printer:
Q *UHHQ: Printer ready
Q Orange: Information message issued - printing stopped
Q Red: Warning message issued - printing stopped
Q *UH\: Printer in hibernation mode, disconnected or communication interrupted.
:KHQDQRWLÀFDWLRQLVLVVXHGLWLVGLVSOD\HGLQDZLQGRZRIWKHIROORZLQJW\SH
Depending on the type of message, you can either:
*HWDGGLWLRQDOKHOSIURPWKH(YROLVVXSSRUWVLWHUHTXLUHVDQ,QWHUQHWFRQQHFWLRQ
Interrupt the printing task.
Restart the task.
The Evolis Printer Manager service can be disabled by right-clicking the Evolis icon on the status
bar.
,QWHUUXSWLQJWKH(YROLV3ULQWHU0DQDJHUVHUYLFHLVRQO\UHFRPPHQGHGLIWKHUHLVDFRQÁLFWZLWKRWKHUDSSOLFDWLRQV
installed on your computer. The Evolis Printer Manager service is the best way of monitoring your printer effectively
from your workstation.
2
2-4 Printing a card
$ODUJHQXPEHURI:LQGRZVDSSOLFDWLRQVDOORZGRFXPHQWVWREHSULQWHGIRUH[DPSOHWKHWRROVLQ0LFURVRIW·V2IÀFHVXLWHLH06:RUG
MS-Access, Ms-Excel, MS-PowerPoint).
7RJDLQIDPLOLDULW\ZLWKWKHOD\RXWRIDFDUGDQGFRQÀJXULQJLWVIRUPDWWLQJDQGSULQWLQJZHVXJJHVWWKHIROORZLQJH[DPSOH
³ In Microsoft® Word
After having set the Evolis printer as the default:
Q Start the MS-Word application
Q Click on the File in the menu bar, then on Page Setup
Q In the Margins tab, set all margins to ‘0’, then in the Orientation section, select Landscape.
Q The Paper tab has a Paper Size option, select CR80 Card
Q For Word 2010: click the Page layout tab, then click on Size and select ‘CR80 Card‘
Q Close the window by clicking OK.
Your Word window should now look like this:
<RXDUHUHDG\WRFXVWRPLVH\RXUFDUGE\DGGLQJWKHYDULRXVLWHPVWKDWJRWRPDNH
up a card:
Q Logo and Illustration
Q,GHQWLÀFDWLRQSKRWR
Q Fixed and variable texts
Q Bar Code, etc.
Once ready, click on File and then on Print.
2
Maintenance
3-1 General warranty information
<RXU(YROLVSULQWHUKDVEHHQGHVLJQHGWRJLYH\RXORQJVHUYLFHDQGQHHGVRQO\PLQLPDOUHJXODUPDLQWHQDQFH3OHDVHFRPSO\ZLWKWKH
instructions given below to ensure that it runs satisfactorily.
Keep your warranty cover!
The manufacturer’s warranty is subject to strict adherence to the routine servicing and maintenance instructions,
and in particular the printer cleaning cycles.
Any failure to follow the maintenance and servicing procedures described in this section voids the print head warranty.
Evolis declines any liability where there has been a failure to carry out required maintenance on the printer.
The print head is a wearing part and an extremely sensitive printer component. Its useful life can be seriously curtailed by the presence of
dust, liquids or solids in the printer’s immediate environment, on the print head or on the cards. Users must take all necessary precautions
to insert only clean cards, free of dust deposits or foreign bodies, into the machine.
The frequency and quality of cleaning are decisive factors enabling users to extend the print head’s useful life and to ensure excellent
print quality. Particular care must therefore be taken with cleaning. Users must comply with the servicing and maintenance instructions
as fully described in this section.
In addition, the use of Evolis brand ribbons (‘Evolis High Trust’) also ensures that your equipment operates properly. Use of ribbons not
approved by Evolis may as a consequence affect the quality and reliability of print jobs, produce low quality printed output and even
affect the printer’s operation. The manufacturer’s warranty does not cover physical damage or quality problems caused by using non-
Evolis approved ribbons.
Evolis provides replacement parts and consumables that you can refer to within this user guide or by visiting the website at
www.evolis.com.
3
3-2 Routine printer cleaning
The print head warranty is directly linked to routine cleaning of your printer.
,I\RXGRQRWFDUU\RXWWKLVFOHDQLQJDWWKHUHTXLUHGWLPHVWKHSULQWKHDGZDUUDQW\ZLOOFHDVHWREHYDOLG
Recommended cleaning cycle: whenever the ribbon is changed
Mandatory cleaning cycle: when the cleaning warning is triggered
Servicing accessory: 7VKDSHG cleaning card.
<RXUSULQWHULVÀWWHGZLWKDFOHDQLQJZDUQLQJV\VWHPZKLFKLVWULJJHUHGDIWHUDFHUWDLQQXPEHURIFDUGVKDYH
been inserted.
You should proceed with the routine cleaning of your printer as soon as the warning is triggered.
If you continue to run the printer despite the warning and if the warning light remains lit, the print head warranty
will be automatically voided owing to a failure to comply with your contractual maintenance obligations.
3
Follow the procedure below to ensure you have carried out regular cleaning properly:
Repeatedly running the adhesive card through the printer cleans the cleaning roller in order to maintain print quality and increases the
service life of the print head.
Remove the cover from the printer as shown.
Using the lever, set the card thickness to the MAX position.
Remove the ribbon as shown on the diagram.
Close the cover and check it has clicked shut.
3
Open the feeder.
Remove any cards present in the feeder.
Close the feeder.
Double click the cleaning button on the control panel before inserting the cleaning card.
¡5HPRYHWKHÀOPIURPWKHDGKHVLYHFDUG and insert the cleaning card into the manual feeder as shown, adhesive
side up . Cleaning starts.
¢ The used cleaning card is ejected automatically by the manual feeder.
Routine cleaning may also be carried out from the Evolis Print Center by clicking on "Start cleaning".
Before using your printer, remember to reset the gauge to the desired card thickness.
¡ ¢
3
¢
The used cleani
ng
c
tarts.
is e
je
cted automatical
ly
b
y
the manual
¡
¢
3-3 SERVICING THE PRINT HEAD
Recommended cleaning cycle: every 5 routine cleaning cycles.
Servicing accessory: cleaning pen
Unplug the printer from its power supply before cleaning the print head.
Follow the cleaning cycles scrupulously.
Avoid any contact between the print head and any metal or sharp objects.
$YRLGWRXFKLQJWKHSULQWKHDGGLUHFWO\ZLWK\RXUÀQJHUVDVWKLVFRXOGDIIHFWSULQWTXDOLW\RUSHUPDQHQWO\GDPDJH
the print head.
The cleaning pen can be used up to 8 times for cleaning the print head.
Follow the procedure below:
Remove the cover from the cleaning pen.
8QSOXJWKHSRZHUVXSSO\FDEOHRSHQWKHFRYHUWKHQÀQGWKHSULQWKHDG
*HQWO\UXEWKHSHQIURPOHIWWRULJKWDORQJWKHSULQWKHDGIRUDIHZVHFRQGV
Close the cover. Reconnect the printer.
Wait for 2 minutes after cleaning before using your printer.
3
Help
This section gives a number of suggestions allowing problems that may arise when using your printer to be pinpointed. If you do not
manage to solve your problem, this section also explains how to contact Evolis technical support.
4-1 Warnings and diagnosis
Although the Evolis printer was designed to work independently, keeping user involvement to a minimum, it may nonetheless prove useful
to gain some familiarity with the main warnings.
4-1a CONTROL PANEL WARNINGS
See section 1 - Description of the printer and its functions for further details about the control panel.
OFF
STEADY LIGHT
FLASHING
Pushbutton
Cards and ribbon
4
3ULQWHU
Q The printer is ready to
receive data.
Q1RULEERQLQWKHSULQWHU
O End of ribbon.
Q The ribbon is not correctly
ÀWWHG
Q The ribbon is torn.
Q The ribbon is not
recognized.
Check the condition of the
ribbon in the printer. If you
have a print job in progress,
this restarts with a new card.
Q The printer is receiving
data.
Q1RFDUGVLQWKHFDUG
feeder.
Put cards back into the
feeder - the process starts
again.
PRINTER READY
RIBBON
PROCESSING
CARDS
Q Card loading error.
Check cards have been
loaded. For any other problem
contact your Evolis dealer.
4
Q The printer cover is open.
Close the cover again. The
printer starts up.
PRINTER COVER OPEN
Q Card jammed in the
printer.
Q Mechanical component
fault.
Open the cover and hold
down the pushbutton in
order to eject the jammed
card. For more details, refer
to section 4-3b.
If the problem persists,
contact your Evolis dealer
for assistance.
MECHANICAL ERROR
4
Q The cooling system has
been activated.
The printer pauses for a few
seconds and restarts once
it has returned to its normal
operating temperature.
Q The printer is updating its
Firmware.
The printer restarts following
the update.
COOLING MODE FIRMWARE UPDATE
4-2 Diagnosis help
,QWKLVVHFWLRQ\RXZLOOÀQGDOOWKHLQIRUPDWLRQ\RXQHHGWRFDUU\RXWDIHZVLPSOHFKHFNVWKDW\RXPD\EHDVNHGWRUXQE\\RXU(YROLVGHDOHU
to help you as effectively as possible.
4-2a PRINTING A TECHNICAL TEST CARD
We recommend that you print a technical test card to ensure that your printer is working properly. This card shows various items of
WHFKQLFDOLQIRUPDWLRQFRQFHUQLQJWKHPDFKLQHVHULDOQXPEHUÀUPZDUHFOHDQLQJRSHUDWLRQVSULQWKHDGHWF<RXPD\EHDVNHGIRU
these by your dealer.
³ Printing a technical test card
:DLWIRUDQ\FXUUHQWSULQWMREVWRÀQLVK
Check that there is a ribbon and card in the printer.
Press the pushbutton for four seconds. All the warning lights go out.
Press and hold down the pushbutton again.
The pushbutton light comes on.
5HOHDVHWKHSXVKEXWWRQRQFHWKHOLJKWÁDVKHV
7KHWHVWFDUGLVSULQWHGLQFRORXULIDFRORXUULEERQLVÀWWHGLQWKHSULQWHURUPRQRFKURPHLIWKHULEERQLVPRQRFKURPH
The printed card is ejected into the output hopper.
Printing the technical test card can also be launched from the Evolis Print Center.
4-2b PRINTING A GRAPHIC TEST CARD
The graphic test card is used to check the print quality in colour or monochrome, the offsets and whether the ribbon is synchronised
correctly.
7RSULQWWKHJUDSKLFWHVWFDUGFKHFNÀUVWRIDOOWKDWDULEERQDQGDFDUGDUHSUHVHQWLQWKHSULQWHU
*RWREvolis Print Center, select System information and click on the Test cards tab. Then click the Graphic test card button. The card is
printed and the printed card is ejected into the output hopper.
Printing the graphic test card can only be launched from the Evolis Print Center.
4
F,'(17,)<,1*,167$//('62)7:$5(9(56,216
<RXFDQLGHQWLI\GLUHFWO\WKHV\VWHPYHUVLRQVLQVWDOOHGSULQWGULYHUVHWHWF
In Evolis Print Center, double click the name of the printer to display its Properties.
Click System information, then System information.
4
4-3 Troubleshooting
Do not attempt to use tools or other items to repair your printer in the event of problems, in case major damage
is caused.
4-3a PRINTING PROBLEMS
³ Nothing prints
Check the print driver
&KHFNWKDWWKHUHLVDSULQWGULYHUIRU\RXUSULQWHULQWKH:LQGRZVFRQÀJXUDWLRQ
Check that the printer is selected as the default printer.
Check the printer's power supply
Check that the power cable is correctly connected to the printer and to a working electrical socket.
Check that the printer is on and that the pushbutton is lit.
Make sure you are using the power supply unit supplied with the printer.
Check the USB cable
Check that the USB cable is connecting the printer to your computer.
Check the ribbon
&KHFNWKDWWKHULEERQLVÀWWHGFRUUHFWO\DQGWKDWWKHFRYHULVFORVHG
Check the cards
Check that there are cards in the card feeder.
Check that no cards are jammed in the printer.
Print a test card
See elsewhere in this section for the procedure to be followed.
³ Blank card ejected
Check the ribbon
&KHFNWKDWWKHULEERQLVQRWÀQLVKHGRUGDPDJHG5HSODFHLWRUUHLQVWDOOLWLIQHFHVVDU\
The print head may be damaged
Print a test card.
If the test card does not print, contact an Evolis dealer for technical support or visit the website at www.evolis.com.
4
³ Poor print quality
Small blemishes on the card
Q The card surface may be dirty.
Check that your cards are perfectly clean.
Use new cards.
Q Cleaning roller or print head clogged.
Run a cleaning cycle.
Horizontal white lines
Q 7KHULEERQLVQRWFRUUHFWO\ÀWWHG
Check that there are no wrinkles on the ribbon surface.
Q Print head dirty or damaged.
Clean or replace the print head.
Blurred image
Q 7KHULEERQLVQRWFRUUHFWO\ÀWWHG
Check that the ribbon is correctly positioned in the printer.
Q Poor ribbon synchronisation.
Open and close the printer cover to synchronise the ribbon.
Q Dirty printer or cleaning roller.
Clean the printer
Q Use of incompatible cards.
&KHFNWKDWWKHFDUGVXVHGPDWFKWKHVSHFLÀFDWLRQV
We recommend that you obtain your cards from an Evolis dealer.
8VHRIFDUGVREWDLQHGHOVHZKHUHLVOLDEOHWRDGYHUVHO\DIIHFWSULQWTXDOLW\DQGRUGDPDJHWKHSULQWKHDG
4
³ Partial or incorrect printing
Check the print settings
Check that no area of the card design to be printed is outside the print margins.
&KHFNWKHGRFXPHQWRULHQWDWLRQSRUWUDLWRUODQGVFDSHLQWKH(YROLV3ULQW&HQWHUFRQÀJXUDWLRQ
Check the interface cable
If irregular characters are printed, check that you are in fact using the USB cable supplied with your printer.
Check the connection between the computer and the printer.
Try using another cable of the same type.
Check that the printer is clean
Clean the printer, especially the cleaning roller.
See the maintenance section.
Check that the cards are clean
Store your cards protected from dust.
Check the ribbon
&KHFNWKDWWKHULEERQLVÀWWHGFRUUHFWO\
Check that the ribbon spools freely.
Check the print head
Should horizontal straight lines appear on printed cards, it is likely that the print head is dirty or damaged.
See the section on maintenance and troubleshooting. If the problem persists, contact an Evolis dealer or visit the
website at www.evolis.com.
4
4-3b FREEING JAMMED CARDS
Control panel displays:
Do not turn off your printer as this cancels pending print jobs in the printer’s memory.
Remove the card as follows:
Open the printer cover and remove the ribbon.
Press the pushbutton to turn the card transport rollers. If the card is still stuck inside the printer, slide it manually towards
WKHSULQWHURXWSXW,IWKHUHLVPRUHWKDQRQHFDUGDOZD\VSXVKWKHWRSRQHÀUVW
Replace the ribbon, then close the printer cover.
To prevent card jams:
Check that the card thickness gauge is correctly adjusted.
&KHFNWKDWWKHWKLFNQHVVRIWKHFDUGVXVHGPDWFKHVWKHVSHFLÀFDWLRQVVHWRXWLQ$SSHQGL[$´7HFKQLFDOVSHFLÀFDWLRQVµ
in this manual.
&KHFNWKDWWKHFDUGVDUHÁDW.HHSWKHPLQDKRUL]RQWDOSRVLWLRQ
&KHFNWKDWWKHFDUGVDUHQRWVWXFNWRJHWKHU6KXIÁHWKHFDUGVEHIRUHORDGLQJWKHP
Q Card jammed in the printer. Print jobs are interrupted.
MECHANICAL ERROR
4
4-3c REPLACING THE PRINT HEAD
The print head is a sensitive component of your equipment. It determines the print quality, and regular servicing along with an immediate
HQYLURQPHQW IUHH IURP GXVW RU RWKHU SDUWLFOHV HQVXUH D OHQJWK\ XVHIXO OLIH 1RQHWKHOHVV WKH SULQW KHDG PD\ VRPHWLPHV QHHG WR EH
replaced. Evolis has designed a unique device enabling users to undertake such replacement with no tools needed, simply by following
the instructions very carefully.
Before doing anything else, please contact your Evolis dealer in order to check the advisability of replacing the print head. The dealer will
supply a new print head if need be.
For more information on print head warranties, refer to the Evolis warranty booklet.
4
To exchange the print head, please proceed as follows:
Before changing the print head, please unplug the power cable.
³ Step 1 - Removing the defective print head
Open the printer cover.
Locate the print head.
Press on the plastic part behind the head (pressure plate) and pull on the head with the other hand as shown in the
diagram in order to free the lugs from the holding fork, then remove the lugs from their slots.
Tilt the head carefully downwards and disconnect the connector linked to the cable without using force on the
mechanism.
4
mechanis
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
m.
³ Step 2 - Installing the new print head
1RWHWKHFRGHVKRZQRQWKHZKLWHODEHOVWXFNRQWKHSULQWKHDG<RXZLOOEHDVNHGIRUWKLVFRGHLQ6WHS
Take the new head and insert it vertically (white connector upwards) raising it in the two guides so as to trap the lugs of
the fork in their slots . Then lower it by pressing on the two forks , a click will be heard.
Connect the cable into its socket, making sure it is the right way round. Do not use any force, as this part is relatively
fragile. Press down on each side of the connector to ensure a good connection is made.
The head is back in position.
&ORVHWKHFRYHU7KHSULQWKHDGLVQRZÀWWHG
4
³6WHS&RQÀJXULQJWKHQHZSULQWKHDG
Power up the printer and check that it is properly connected to a computer on which the printer’s Evolis Print Center is
installed.
In Maintenance of Evolis Print Center, click on the Change print head tab.
(QWHUWKH3.1QXPEHURIWKHSULQWKHDGNLWLQEnter PKN no., the number you noted down in step 2. Then click &RQÀUP.
If the print head kit number is not entered correctly, printer malfunctions may occur and the warranty may be
voided.
4
4-3d UPDATING THE FIRMWARE (under Windows)
8SGDWLQJWKHÀUPZDUHLVDVLPSOHRSHUDWLRQEXWRQHZKLFKLIQRWSURSHUO\FRPSOHWHGFDQUHVXOWLQ\RXUSULQWHUEUHDNLQJGRZQ
Before any update, please contact your Evolis dealer who will be able to guide you on the advisability or otherwise of carrying out an
XSJUDGH,QJHQHUDOVXFKXSGDWHVDUHRQO\UHTXLUHGLQWKHHYHQWRISUREOHPRUPDOIXQFWLRQWKDWKDVEHHQFOHDUO\LGHQWLÀHGE\\RXU(YROLV
dealer.
Updates can be downloaded from the website at www.evolis.com:
*RWRWKHSupport & Drivers menu, then select your printer model and click on the Print drivers and Firmware link.
7KHQFOLFNRQWKHÀOHIRUWKHFRUUHVSRQGLQJ)LUPZDUH
$FFHSWWKHGRZQORDGWKHQVDYHWKHÀOHLQDGLUHFWRU\RQ\RXUKDUGGULYH7KHÀUPZDUHLVVWRUHGFRPSUHVVHGDVD]LS
ÀOHZKLFK\RXZLOOQHHGWRH[WUDFW
7KHQGRXEOHFOLFNRQWKHÀOHLQWKHGLUHFWRU\LQRUGHUWRUXQWKHÀUPZDUHLQVWDOODWLRQSURJUDP
When requested by the program, follow the instructions in order to select the printer and start the operation. The
ÀUPZDUHGRZQORDGLVLQSURJUHVV
$IWHUDERXWWKLUW\VHFRQGVWKHÀUPZDUHKDVWUDQVIHUUHGWRWKHSULQWHUDQGWKHRSHUDWLRQLVFRPSOHWH
,IWKHSULQWHULVQRWVKRZLQJD¶5($'<·VWDWXVWKLVPHDQVWKDWWKHXSGDWHKDVQRWEHHQFDUULHGRXWFRUUHFWO\RUSRVVLEO\
that the printer is not working properly. Check the connection cables and run a new update.
The update is complete, and your equipment is ready to customise your cards.
Never interrupt the transfer between computer and printer during the download phase (powering off the printer
or computer, unplugging a cable). This would result in a complete inability to restart the printer. Should such an
incident occur, please contact your Evolis dealer, who will replace your printer’s processing board.
7KHXSGDWHRIWKHÀUPZDUHFDQEHFDUULHGRXWIURPWKH(YROLV3ULQW&HQWHU
4
4-3e UPDATING THE PRINT DRIVER
8SGDWLQJWKHSULQWGULYHULVDWDVNWKDWLVUHTXLUHGLQRUGHUWRÀ[PDOIXQFWLRQVRUJDLQWKHEHQHÀWRIQHZRSWLRQV
Before any update, please contact your Evolis dealer who will be able to guide you on the advisability or
otherwise of carrying out an upgrade.
Updates can be downloaded from the website at www.evolis.com:
*RWRWKHSupport & Drivers menu, then select your printer model and click on the Print drivers and Firmware link.
7KHQFOLFNRQWKHÀOHIRUWKHFRUUHVSRQGLQJSULQWGULYHU
$FFHSWWKHGRZQORDGWKHQVDYHWKHÀOHLQDGLUHFWRU\RQ\RXUKDUGGULYH7KHÀUPZDUHLVVWRUHGFRPSUHVVHGDVD]LS
ÀOHZKLFK\RXZLOOQHHGWRH[WUDFW
7KHQGRXEOHFOLFNRQWKHVHWXSH[HÀOHWKDW\RXKDYHMXVWGRZQORDGHGLQRUGHUWRUXQWKHLQVWDOODWLRQSURJUDP
For more details about the procedure, please see the Installing the print driver section.
4
4-4 Technical support
,I\RXDUHKDYLQJGLIÀFXOWLHVLQFRQÀJXULQJDQGXVLQJ\RXUSULQWHUUHDGWKLVPDQXDOFDUHIXOO\
If you do not manage to solve your problem, you can obtain further information and help from the Evolis partner network.
4-4a EVOLIS PARTNER NETWORK
For any unresolved technical problem, contact an Evolis dealer. If you do not know any Evolis dealers, visit the www.evolis.com website
and send us your question. Evolis will pass on the contact details of your nearest Evolis dealer. When calling an Evolis dealer, you do need
to be close to your computer and ready to provide the following information:
<RXUSULQWHUPRGHODQGVHULDOQXPEHU
7KHFRQÀJXUDWLRQDQGRSHUDWLQJV\VWHPWKDW\RXDUHXVLQJ
A description of the incident that has occurred
A description of the steps that you have taken to resolve the problem.
,QDGGLWLRQWRHQDEOH\RXWRÀQGDQVZHUVWR\RXUTXHVWLRQVWKHwww.evolis.com website includes a number of aspects related to
day-to-day use of your printer.
4-4b FINDING INFORMATION ON WWW.EVOLIS.COM
,I\RXQHHGDGGLWLRQDOWHFKQLFDOKHOS\RXZLOOÀQGDJUHDWGHDO RILQIRUPDWLRQRQXVLQJDQG WURXEOHVKRRWLQJ(YROLVSULQWHUVXQGHUWKH
Drivers and Support section on the Evolis website at www.evolis.com.
7KLVVHFWLRQRIIHUVGRZQORDGVRIWKHODWHVWYHUVLRQVRIÀUPZDUHSULQWGULYHUVDQGXVHUPDQXDOVYLGHRVDERXWXVLQJDQGPDLQWDLQLQJ(YROLV
printers, and an FAQ* section giving answers to the most frequently asked questions.
*FAQ: Frequently Asked Questions
4
Appendix A
$7HFKQLFDOVSHFLÀFDWLRQV
This section presents your printer’s technical printing properties.
³ General technical features
Q
Q
Q
Q
Q
Single side print module, edge-to-edge printing
Colour sublimation and monochrome thermal transfer
0 dpi print head (11.8 dots/mm)
16 million colours
16MB RAM
³ Printing speed
Full card print%DGJ\
Q<0&.2
Q0RQRFKURPH
FDUGVKRXU
FDUGVKRXU
³ Card management and technical data
Q
Q
Q
Q
Q
Automatic feeder
Feeder capacity: 50 cards (0.76 mm – 30 mil)
Output hopper capacity: 20 cards (0.76 mm – 30 mil)
Card types: PVC and composite PVC cards, recycled PET cards, PET, ABS1 and special clear overlaid cards1
Card format: ISO CR80 - ISO 7810 (53,98 mm x 85,60 mm)
1 8QGHUVSHFLÀFFRQGLWLRQV
A
Full card print%DGJ\
Q<0&.2
Q0RQRFKURPH
FDUGVKRXU
FDUGVKRXU
³ Ribbons
To maximise the quality and lifetime of the printed cards, the service life of your print head and the overall reliability of your printer, use
Evolis High Trust ribbons.
Q$XWRPDWLFLGHQWLÀFDWLRQDQGVHWWLQJ
Q Ribbon inserted in a cassette to make handling easier
Q*UDSKLFQRWLÀFDWLRQRIWKHULEERQOHYHODOPRVWÀQLVKHGÀQLVKHG
Q Integrated ribbon saving for monochrome printing
Q Ribbon:
<0&.2SULQWVUROO
.2SULQWVUROO
0RQRFKURPHULEERQVXSWRSULQWVUROO1
+RORJUDPULEERQSULQWVUROO
1 8QGHUVSHFLÀFFRQGLWLRQV
³ Ports/connectivity
Q USB 1.1 (compatible 3.0)
Q Ethernet port available as an option.
³ Display
Q LEDs
Q*UDSKLFSULQWHUQRWLÀFDWLRQV1:
)HHGHUHPSW\
5LEERQQHDUO\ÀQLVKHGÀQLVKHGZDUQLQJ
(WF
1 Dependant on your version of Windows
³ Software
Q Supplied with Evolis Premium Suite for Windows:
3ULQWHUGULYHU
(YROLV3ULQW&HQWHUIRUWKHDGPLQLVWUDWLRQPDQDJHPHQWDQGFRQÀJXUDWLRQRIWKHSULQWHU
(YROLV3ULQWHU0DQDJHUIRUWZRZD\JUDSKLFQRWLÀFDWLRQ1
&RPSDWLEOHZLWK:LQGRZV;3639LVWD:2:
Q Other platforms:
/LQX[RQUHTXHVW
15HTXLUHVQHWFOLHQWSURÀOHYHUVLRQ
2 For older versions of Windows, upon request only
A
³ Warranty conditions
Q
Q
years' warranty (printer and print head)
Warranty extensions available (contact your Evolis reseller)
³ Dimensions and weight
Q
Q
Dimensions (H x W x L): 1 x 20 x mm
Weight: kg
³ Acoustics (tested in accordance with ISO 7779)
Q Sound pressure in assistant positions LpAmFRORXUPRGH<0&.2
,QRSHUDWLRQG%$
6WDQGE\PRGHEDFNJURXQGQRLVHOHYHO
³ Security
Q Kensington security lock
Q Data encryption for magnetic encoding1
1 Available for the ‘Expert’ range and above
³(FRGHVLJQDQGFHUWLÀFDWLRQV
Q Standby mode and reduced power consumption
Q Printer (1(5*<67$5FHUWLÀHG
Q Printer meets the Energy Related Products Directive, ErP, 2009/125/EC
³ Contents of the packaging
Q
Q
Q
Q
Q
Printer
CD-ROM with printer driver, user manuals
USB cable
Power supply unit
Power supply lead (differs according to region)
A
³ Options & accessories
Q
Q
&RORXUVDYDLODEOH)LUHUHGDQG*UH\%URZQ
Ethernet TCP-IP1
³&HUWLÀFDWLRQVDQGGHFODUDWLRQRIFRQIRUPLW\
³ Power supply
Q
Q
3RZHUVXSSO\PRGXOH9ROWV$&+]$
3ULQWHU9ROWV'&$
³ Environment
Q Min/max operating temperature: 15° / 30 °C (59° / 86 °F)
Q Humidity: 20% to 65% without condensation
Q Min/max storage temperature: –5° / +70 °C (23° / 158 °F)
Q Storage humidity: 20% to 70% without condensation
Q Ventilation in operation: open air
³ Other
Q Resident fonts
$ULDO$ULDOEROG
%DUFRGHVFRGHFRGH($1LQWHUZHDYHG
A
CE, FCC, IEC, VCCI, CCC, KC
ErP 2009/125/CE, (1(5*<67$5, RoHS
Q
Q
Appendix B
B1 - Compliance statements
In this section, you will nd the certications for your Evolis printer.
Compliance statements
Concerning Safety and Electromagnetic Compatibility of Radio
Equipment (R&TTE 1999/5/CE, 2006/95/CE and 2004/108/CE Directives)
Manufacturer name: Evolis Card Printer
Manufacturer address: 14, avenue de la Fontaine
Equipment name:
Z.I. Angers Beaucouzé
49070 Beaucouzé, France
Badgy100 & Badgy200
Year of manufacture: 2014
I, the undersigned,
Serge Olivier,
Declare under my own responsibility, that the product described above
complies with the essential applicable requirements of the 1999/5/CE,
2006/95/CE and 2004/108/CE directives:
Article 3.1 b: (electromagnetic compatibility protection requirement)
Safety standard applied EN60950-1:2006 + A11: 2009 + A1: 2010 + A12: 2011
EN50364:2001
EN62311:2008
Article 3.1 b: (electromagnetic compatibility protection requirements)
EMC standard applied EN55022:2006 + A1
EN55024:1998 + A1 + A2
EN61000-3-2:2006
EN61000-3-3:2008
EN301489-3:V1.4.1
Article 3.2: (Good use of the radio frequency spectrum to avoid undesirable interferences)
EMC standard applied EN302291-2 V1.1.1
Full name: Serge Olivier
Position: R&D Director
Date: 2014
Signature:
EUROPE - Norway Only: This product is designed for IT power system with phase-
to-phase voltage 230V. Earth grounding is via the polarized, 3-wire power cord.
FI: “Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan”
SE: “Apparaten skall anslutas till jordat uttag”
NO: “Apparatet må tilkoples jordet stikkontakt”
FCC Federal Communications Commission notice
Radio frequency interference in the United States
The Badgy100 and Badgy 200 models complie with the following
specification: FCC Part 15, Subpart A, Section 15.107(a) and
Additional information:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try the following measures: - Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the radio or television.
- Connect the equipment to a circuit other than that to which the receiver is connected.
- Consult the supplier or an experienced radio/TV technician.
Use of a shielded twisted pair cable is necessary to comply with the restrictions laid down by part 15 of the FCC Rules
for Class B digital devices.
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications made to this equipment without the
express, written consent of Evolis Card Printer may cause harmful interference and void the FCC authorisation
to operate this equipment.
This equipment complies with FCC’s radiation exposure limits set forth for an uncontrolled environment under the
following conditions :
1.This equipment should be installed and operated such that a minimum separation distance of 20 cm is maintained
between the radiator (antenna) and user’s/nearby person’s body at all times.
2.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with the Industry Canada CNRs applicable to licence-exempt audio devices. Their use is
authorised subject to the following two conditions: (1) the device must not cause interference and (2), the user of the
device must accept any radio interference to which they may be subject even if the jamming is liable to adversely
affect operation.
Japanese radio frequency interference (VCCI)
This equipment is Class B information technology equipment based on the rules
laid down by the Voluntary Control Council For Interference by Information
Technology Equipment (VCCI). Its use in or close to a residential area may
cause radio interference, in which case, you must take appropriate steps.
41
B
Section 15.109(a) Class B Digital device