Ecolink Intelligent Technology TLSZWAVE5 Z-Wave Plus Single Gang Toggle Wireless Light Switch User Manual
Ecolink Intelligent Technology, Inc. Z-Wave Plus Single Gang Toggle Wireless Light Switch
User manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3391490 |
| Application ID | D54li02RAZ36tywDgTJzAw== |
| Document Description | User manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 51.92kB (648941 bits) |
| Date Submitted | 2017-05-15 00:00:00 |
| Date Available | 2017-06-29 00:00:00 |
| Creation Date | 2017-05-08 13:02:15 |
| Producing Software | Microsoft® Word 2013 |
| Document Lastmod | 2017-05-08 13:02:15 |
| Document Title | User manual |
| Document Creator | Microsoft® Word 2013 |
| Document Author: | Bailey |
Z-Wave Plus Toggle Light Switch Installation Instructions Product Overview Z-Wave Plus™ enabled device which can be used turn a light switch on or off Z-Wave Plus™ enabled device which can be used sense status of a light switch Product Specifications For indoor use only Operating frequency: 908.42 MHz Operating temperature: 0° – 49°C, 32° – 120°F (ambient temperature) Operating humidity 5-95% non-condensing 2 AA batteries Battery Life: 1 year Network Inclusion The Z-Wave Plus Toggle Light Switch must be added to a Z-Wave Plus network prior to use. To include the device in a network both the device and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controller’s inclusion mode. 1) 2) 3) 4) 5) Verify that the Z-Wave Plus controller you are using is compatible with the Z-Wave Plus Toggle Light Switch. Locate the light switch desired to be used with the Z-Wave Plus Toggle Light Switch. Put your Z-Wave Plus Controller into add (inclusion) mode. Press the inclusion / exclusion button on the Z-Wave Plus Toggle Light Switch. (Figure 1) The LED on the front of the unit will turn off if successful included into a network. Network Exclusion 1) Any Z-Wave Plus Device can be removed from any Z-Wave Plus controller. Follow the directions to put your Z-Wave Plus Controller into exclusion mode. 2) Press the inclusion / exclusion button on the Z-Wave Plus Toggle Light Switch. Network Inclusion/Exclusion: Key Points to Remember Controller inclusion mode must be activated BEFORE starting sensor inclusion or exclusion mode. The device can only be included into one controller network at a time, and must be excluded from one network before inclusion in another Exclusion mode on the senor is initiated following the same exact procedure as inclusion. © 2017 Ecolink Intelligent Technology Inc. PN TLS-ZWAVE5 R2 LED Status The Z-Wave Plus Toggle Light Switch is equipped with a red LED. The state of the LED will change based on the state of the device. LED Blinking LED On LED blink - Device not included into a network. - Device In Learn mode. - Device in lower power mode. Remote control disabled. Battery State The Z-Wave Plus Toggle Light Switch will alert the user when the batteries become low. While the batteries are low, the user will be unable to change the light state remotely. The Z-Wave Plus toggle Light Switch will continue reporting the state of the switch until the batteries are completely depleted. Factory Default The Z-Wave Plus device is automatically factory defaulted when removed from a Z-Wave Plus network. Please use this procedure only when the network primary controller is missing or otherwise inoperable. Inclusion / Exclusion button Figure 1 Installation The package contains the following: Ecolink Z-Wave Plus Toggle Light Switch Screw for the Z-Wave Plus Toggle Light Switch 2 AA batteries © 2017 Ecolink Intelligent Technology Inc. PN TLS-ZWAVE5 R2 STEP ONE Identify Location for Z-Wave Plus Toggle Light Switch: STEP TWO Remove the switch plate cover from the Light Switch you wish to install the device on. Save the screws for step three. STEP THREE Replace the switch plate cover with the Z-Wave Plus Decora Light Switch using the screws from step two. Figure 2 STEP FOUR Follow the Network Inclusiuon steps on page 1. STEP FIVE Place the cover on the Z-Wave Light Switch. Z-Wave Plus Specific Information © 2017 Ecolink Intelligent Technology Inc. PN TLS-ZWAVE5 R2 Z-Wave Plus is a wireless mesh network and data protocol that allows devices from many different manufacturers to interoperate. This device implements ZWave Plus functionality, Network Wide Inclusion, The following information is intended for software engineers working on Z-Wave Plus controllers and home automation enthusiasts to integrate the Z-Wave Plus device into their system. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Generic Device Class GENERIC_TYPE_BINARY_SWITCH Specific Device Class SPECIFIC_TYPE_POWER_SWITCH_ BINARY v2 v2 v2 v1 v1 v1 v2 v1 v1 v2 Device Classes Command Classes COMMAND_CLASS_ZWAVEPLUS_INFO COMMAND_CLASS_VERSION COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_BATTERY COMMAND_CLASS_SWITCH_BINARY COMMAND_CLASS_ASSOCIATION COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_BASIC COMMAND_CLASS_FIRMWARE_UPDATE_MD Manufacturer ID 0x014A Product Type 0x00 06 Product ID 0x00 02 Z-Wave Plus Command Class Basic For backwards compatibility with older Z-Wave Plus Controllers, the Basic Command Class is supported in the following manner. A Basic Set of 0xFF will turn on the light switch. A basic set of 0x00 will turn off the light switch. Command Class Association © 2017 Ecolink Intelligent Technology Inc. PN TLS-ZWAVE5 R2 This Z-Wave Plus Toggle Light switch has two Association groups of 5 nodes. Group one – Group one is the lifeline group. The Light Switch will send Switch Binary Reports with a value of 0x00 if the light is turned off and 0xFF if the light is turned on to all nodes in group 2. Group two – The light switch will send basic reports with a value of 0x00 if the light is turned off and 0xFF if the light is turned on to all nodes in group 2. Network Wide Inclusion This device also supports Network Wide Inclusion such that the device can be included into the Z-Wave network over the mesh network and not directly near the main controller. This mode is automatically activated after regular inclusion was not successful. FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Re-orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment to an outlet on a different circuit from the receiver Consult the dealer or an experienced radio/TV contractor for help. Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc. could void the user’s authority to operate the equipment. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et (2) c’et appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de la dispositif. FCC ID: XQC-TLSZWAVE5 IC: 9863B-TLSZWAVE5 © 2017 Ecolink Intelligent Technology Inc. PN TLS-ZWAVE5 R2 LIMITED WARRANTY This limited warranty is provided by Ecolink Intelligent Technology (“Ecolink”) to you as the original purchaser of the product. Ecolink warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of original purchase. The determination of whether the product is defective shall be made by Ecolink in its sole discretion with consideration given to the overall performance of the product. If Ecolink determines that any product is defective, Ecolink’s sole obligation and your sole and exclusive remedy shall be that Ecolink will replace the product. This warranty does not apply to damage caused by shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or as a result of any unauthorized modifications. The foregoing limited warranty is and shall be in lieu of any and all other warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink. Ecolink neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product. It is recommended that the customer check their equipment on a regular basis for proper operation. DISCLAIMER AND LIMITATION OF LIABILITY OTHER THAN THE LIMITED WARRANTY ABOVE, ECOLINK MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. YOU ACKNOWLEDGE THAT YOU ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE INTENDED USE. IN NO EVENT SHALL ECOLINK OR ANY OF ITS AFFILIATES BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, CONSEQUENTIAL, OR MULTIPLE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOST PROFITS, LOSS OR DAMAGE TO SOFTWARE OR DATA, OR DAMAGE TO EQUIPMENT ARISING OUT OF THE USE OF ANY PRODUCT, EVEN IF ECOLINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. FURTHER, IN NO EVENT SHALL THE LIABILITY OF ECOLINK OR ITS AFFILIATIES EXCEED THE INDIVIDUAL PRICE OF THE PRODUCT ON WHICH LIABILITY IS ASSERTED. By the act of use, setup or assembly of the product, you accept all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the product, you are advised to return the product immediately in new and unused condition to the place of purchase. Some states do not allow the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. RETURN POLICY Please visit us at www.discoverecolink.com/returns to view our return policy. This product covered by one or more claims of patents found at: http://sipcollc.com/patent-list/ © 2017 Ecolink Intelligent Technology Inc. PN TLS-ZWAVE5 R2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 6 Language : en-US Tagged PDF : Yes Author : Bailey Creator : Microsoft® Word 2013 Create Date : 2017:05:08 13:02:15-07:00 Modify Date : 2017:05:08 13:02:15-07:00 Producer : Microsoft® Word 2013EXIF Metadata provided by EXIF.tools