Ecolink Intelligent Technology WST102 Wireless Security Keychain Remote Transmitter User Manual
Ecolink Intelligent Technology, Inc. Wireless Security Keychain Remote Transmitter
User Manual
WST-102 Four Button Wireless Remote
Specifications
Frequency: 345MHz Operating Temperature: 32°-120°F (0°-49°C)
Battery: 3V lithium CR2032 Operating Humidity: 5-95% RH non condensing
Battery life: 5 years Compatible with Honeywell receivers (standard mode)
Enrolling
Each product has a unique serial number printed on the back and each button has a unique loop number
assigned to it as indicated below. You must assign each button to an individual zone and configure it as a BR
(button type) input. Once prompted for the serial number press and release the desired button twice to assign
that button to the zone. Refer to your specific alarm control panel or receiver instructions for details.
Operation
Assigning Users to Remotes (Vista Panels)
When a zone is configured to arm or disarm the system with a wireless remote, that zone must be assigned to
a user code in the control panel for it to operate. Refer to the User Code programming section of your specific
control panel for details on assigning users to buttons.
Replacing the Battery
When the battery is low a signal will be send to the control panel, or when a button is pressed the LED will
appear dim or will not turn on at all. Follow these simple steps to replace the battery
1. With a key or small screwdriver, push up on the black tab located at the bottom of the remote (fig.1)
and slide the chrome trim off.
2. Carefully separate the front and back piece of plastic to reveal the battery
3. Replace with a CR2032 battery ensuring the + side of the battery faces up (fig.2)
4. Re-assemble the plastics and ensure they click together
5. Ensure the notch in the chrome trim is aligned with the back of the plastic. It will only go on one way.
(fig.3)
Figure 1
Figure 2
Figure 3
Away Arming (Loop 3)
Press this button to arm your system when
no one will be home. All the sensors in the
systems will be in the armed mode.
Stay Arming (Loop 4)
Press this button to arm your system while
you are still at home. All the doors and
window will be armed but the motion
detectors will remain in standby mode.
Disarm (Loop 2)
Press this button to disarm your system. You do
not have to enter your access code when you
use this key to disarm the system.
Aux (Loop 1)
Press this button to activate the auxiliary
function assigned to this button. Refer to your
specific panel instructions for the available
options.
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC Rules. This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Re-orient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment to an outlet on a different circuit from the receiver
Consult the dealer or an experienced radio/TV contractor for help.
Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc. could void
the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est
soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et (2) c’et
appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de la dispositif.
FCC ID:XQC-WST102 IC: 9863B-WST102
Warranty
Ecolink Intelligent Technology Inc . warrants that for a period of 5 years from the date of purchase that this
product is free from defects in material and workmanship. This warranty does not apply to damage caused by
shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper
maintenance, failure to follow instructions or as a result of any unauthorized modifications.
If there is a defect in materials and workmanship under normal use within the warranty period Ecolink
Intelligent Technology Inc. shall, at its option, repair or replace the defective equipment upon return of
the equipment to the original point of purchase.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink
Intelligent Technology Inc. neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or
liability concerning this product.
The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for any warranty issue
shall be limited to a replacement of the defective product . It is recommended that the customer check their
equipment on a regular basis for proper operation.
© 2013 Ecolink Intelligent Technology Inc. PN WST102 R1.00
2055 Corte Del Nogal
Carlsbad, California 92011
1-855-632-6546
www.discoverecolink.com