Ecolink Intelligent Technology WST201 Wireless Security Door/Window Contact User Manual WST201 manualx

Download:
Mirror Download [FCC.gov]
Document ID	1872271
Application ID	+0rNb9Xmwq26MvNnUB1K9Q==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	5.71kB (71344 bits)
Date Submitted	2012-12-31 00:00:00
Date Available	2013-06-29 00:00:00
Creation Date	2012-12-19 13:26:02
Producing Software	Nitro PDF PrimoPDF
Document Lastmod	2012-12-19 13:26:02
Document Title	Microsoft Word - WST201 manual.docx
Document Creator	PrimoPDF http://www.primopdf.com
Document Author:	andrew

WST-201 Wireless Contact
Specifications
Frequency: 319.5MHz
Battery: 3V lithium CR2032
Battery life: 5-8 years
th
Magnet gap: 5/8 inch max
Operating Temperature: 32°-120°F (0°-49°C)
Operating Humidity: 5-95% RH non condensing
Compatible with GE/Interlogix receivers
Supervisory signal interval: 60min (approx.)
Enrolling
To enroll the sensor, set your panel into program mode, then go to the Learn Sensors menu. Refer
to your specific alarm panel manual for details on these menus. To activate the case tamper
simply slide the cover up and down, you will hear a click when the case latches are engaging and
disengaging. Continue until the panel responds to the sensor. Then select the appropriate sensor
group and number.
Mounting
Included with the contact is double sided tape for the contact and the magnet. For reliable
bonding ensure the surface is clean and dry. Apply the tape to the sensor and then to the desired
location. Apply firm pressure for several seconds. It is not recommended to mount the tape at
temperatures below 50°F, although after 24 hours the bond will hold at low temperatures.
One side of the sensor is marked with 3 lines; this indicates the location of the reed switch. The
magnet should be mounted facing this side of the sensor, and it must be no further than 5/8 of an
inch from the sensor.
Interchangeable covers
The contact comes from the factory assembled with a white cover, but included are option brown
covers. To change the cover simply slide the front cover to disengage it from the sensor then
remove. Replace with the brown cover ensuring the Top (as marked on the inside of the cover)
points away from the battery. You should hear a click when the cover engages and disengages
from the sensor. You do not need to replace the back plastic because once mounted the back is
not visible.
To replace the magnet cover you will need to gently pry the white cover off with a flat head screw
driver and snap the brown cover in place.
Replacing the Battery
When the battery is low a signal will be sent to the control panel. To replace the battery:
1.
2.
3.
Slide the top cover to disengage it from the sensor, then remove to reveal the battery.
Replace with a CR2032 battery ensuring the + side of the battery faces towards you.
Re-attached the cover, ensure the Top (as marked on the inside of the cover) points away
from the battery. You should hear a click when the cover engages properly.
Note: Removing the cover will trigger a zone tamper signal to the control panel
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Re-orient or relocate the receiving antenna
•
Increase the separation between the equipment and receiver
•
Connect the equipment to an outlet on a different circuit from the receiver
•
Consult the dealer or an experienced radio/TV contractor for help.
Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc. could void
the user’s authority to operate the equipment.
Industry Canada Compliance Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est
soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et (2) c’et
appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de la dispositif.
FCC ID: XQC-WST201
IC:9863B-WST201
2055 Corte Del Nogal
Carlsbad, California 92011
1-855-632-6546
www.discoverecolink.com
© 2012 Ecolink Intelligent Technology Inc.
PN WST201 R1.01
Warranty
Ecolink Intelligent Technology Inc. warrants that for a period of 5 years from the date of purchase that this
product is free from defects in material and workmanship. This warranty does not apply to damage caused by
shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper
maintenance, failure to follow instructions or as a result of any unauthorized modifications.
If there is a defect in materials and workmanship under normal use within the warranty period Ecolink
Intelligent Technology Inc. shall, at its option, repair or replace the defective equipment upon return of
the equipment to the original point of purchase.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink
Intelligent Technology Inc. neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or
liability concerning this product.
The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for any warranty issue
shall be limited to a replacement of the defective product . It is recommended that the customer check their
equipment on a regular basis for proper operation.
2055 Corte Del Nogal
Carlsbad, California 92011
1-855-632-6546
www.discoverecolink.com
© 2012 Ecolink Intelligent Technology Inc.
PN WST201 R1.01

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Page Count                      : 3
Producer                        : Nitro PDF PrimoPDF
Create Date                     : 2012:12:19 13:26:02+08:00
Modify Date                     : 2012:12:19 13:26:02+08:00
Title                           : Microsoft Word - WST201 manual.docx
Creator                         : PrimoPDF http://www.primopdf.com
Author                          : andrew

EXIF Metadata provided by EXIF.tools