Ecolink Intelligent Technology WST221 Recessed Door Sensor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2425884
Application ID	k/x1JaQTt7JGh9AFYABTdA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	17.96kB (224491 bits)
Date Submitted	2014-10-23 00:00:00
Date Available	2015-04-21 00:00:00
Creation Date	2014-09-10 11:33:28
Producing Software	Microsoft® Word 2010
Document Lastmod	2014-09-10 11:33:28
Document Title	User manual
Document Creator	Microsoft® Word 2010
Document Author:	Quinto

WST-221 Wireless Recessed Contact
Specifications
Frequency: 319.5MHz
Battery: 3V lithium CR-2
Battery life: 5 years
Magnet gap: 1 inch max
Operating Temperature: 32°-120°F (0°-49°C)
Operating Humidity: 5-95% RH non condensing
Compatible with GE/Interlogix receivers
Supervisory signal interval: 60min (approx.)
Enrolling
To enroll the sensor, set your panel into program mode, then go to the Learn Sensors menu. Refer
to your specific alarm panel manual for details on these menus. To activate the case tamper
simply slide the cover up and down, you will hear a click when the case latches are engaging and
disengaging. Continue until the panel responds to the sensor. Then select the appropriate sensor
group and number.
Mounting
The recessed sensor and magnet are designed to fit snuggly in a ¾ inch hole and a small flange on
the outer rim ensures the case cannot be pushed too far into a hole.
Choose a suitable location for the sensor, drill a ¾ inch by 2.5 inch hole in the door for the sensor.
Mark the location for the magnet in the frame directly in line with the sensor and drill a ¾ inch by
½ inch hole for the magnet.
Installing /Replacing the Battery
When the battery is low a signal will be sent to the control panel. To install/replace the battery:
1.
2.
3.
4.
5.
6.
7.
Remove the cap on the transmitter.
Take note of how the circuit board fits into groves on the side of the case.
Carefully slide out the circuit board.
Inspect the battery holder to determine which side the battery is inserted/removed.
Install /replace with a CR-2 battery ensuring the + side of the battery faces towards the
circuit board.
Re-insert the circuit board so that the board slides within groves in the plastics.
Once in, replace the cap.
Note: Removing the cover will trigger a zone tamper signal to the control panel
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is
encouraged to try to correct the interference by one or more of the following measures:

Re-orient or relocate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment to an outlet on a different circuit from the receiver

Consult the dealer or an experienced radio/TV contractor for help.
Warning: Changes or modifications not expressly approved by Ecolink Intelligent Technology Inc. could void
the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
C’et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est
soumis aux deux conditions suivantes: (1) c’et appareil ne peut pas provoquer d'interférences, et (2) c’et
appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de la dispositif.
FCC ID:XQC-WST221
IC: 9863B-WST221
Warranty
Ecolink Intelligent Technology Inc. warrants that for a period of 5 years from the date of purchase that this
product is free from defects in material and workmanship. This warranty does not apply to damage caused by
shipping or handling, or damage caused by accident, abuse, misuse, misapplication, ordinary wear, improper
maintenance, failure to follow instructions or as a result of any unauthorized modifications.
If there is a defect in materials and workmanship under normal use within the warranty period Ecolink
Intelligent Technology Inc. shall, at its option, repair or replace the defective equipment upon return of
the equipment to the original point of purchase.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other
warranties, whether expressed or implied and of all other obligations or liabilities on the part of Ecolink
Intelligent Technology Inc. neither assumes responsibility for, nor authorizes any other person
purporting to act on its behalf to modify or to change this warranty, nor to assume for it any other warranty or
liability concerning this product.
The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for any warranty issue
shall be limited to a replacement of the defective product . It is recommended that the customer check their
equipment on a regular basis for proper operation.
2055 Corte Del Nogal
Carlsbad, California 92011
1-855-632-6546
www.discoverecolink.com
© 2014 Ecolink Intelligent Technology Inc.
PN WST221 R1.00

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Tagged PDF                      : Yes
Author                          : Quinto
Creator                         : Microsoft® Word 2010
Create Date                     : 2014:09:10 11:33:28-07:00
Modify Date                     : 2014:09:10 11:33:28-07:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools