Edelbrock 5419 Users Manual C 357 B Three Deuce Intake Manifold For Small Block Chevy

: Edelbrock Edelbrock-5419-Users-Manual-537684 edelbrock-5419-users-manual-537684 edelbrock pdf

Open the PDF directly: View PDF .
Page Count: 2

Catalog #5419

Rev. 5/05 - RS/mc ©2005 Edelbrock Corporation

Brochure #63-0402Page 1of 2

C-357-B THREE-DEUCE INTAKE MANIFOLD

For Pre-1986 262-400 c.i.d. Small Block Chevrolet V8

Catalog #5419

INSTALLATION INSTRUCTIONS

PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common

tools and procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable

performing this installation, it is recommended to have the installation completed by a mechanic. If you have any questions or

problems, please call our Technical Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through

Friday or e-mail us at edelbrock@edelbrock.com.. PLEASE complete and mail your warranty card. Be sure to write the model

number of this product in the "Part #____" space. THANK YOU.

•DESCRIPTION: Because of the current high demand for multiple carburetion, Edelbrock has reintroduced the C-357-B three

two-barrel manifold #5419 for small-block Chevrolets. This manifold is primarily designed for street rod applications. Please

note “Brackets” section below for your particular installation. NOTE: HEI distributors will not fit. Stock point-type distributors

may require re-phasing to provide adequate clearance for ignition timing adjustment.

•EGR SYSTEMS: Intake manifold will not accept stock EGR (Exhaust Gas Recirculation) equipment. EGR systems are used on

most 1972 and later model vehicles. Check local laws for requirements.

•ACCESSORIES & INSTALLATION ITEMS: Major recommendations are listed below. See our catalog for details. To order a

catalog, call (800) FUN-TEAM, or visit www.edelbrock.com.

•CARBURETOR RECOMMENDATIONS:

CAUTION: Use only small 2 GC Rochester carburetors. For carburetors, linkage and fuel lines, we recommend that you contact

Automotion Rochester Carburetor Service, 837- 36th Avenue Northeast, Great Falls, MT, 59404- (406) 453-5395 (phone and fax).

•THROTTLE &ACCESSORY BRACKETS: The throttle and kickdown bracket on some vehicles may require modification to fit.

This manifold will not accept any alternator bracket assembly which mounted to the OEM manifold (check with aftermarket

suppliers of alternator brackets such as B&M, Mr. Gasket, TD Performance Products, etc.). It has no provision for ignition coil,

and will accept front (early style) oil filler tube. Valve covers with adequate ventilation provisions are required (PCV valve and

breather recommended).

•GASKETS: Do not use competition style intake gaskets for this street manifold. Due to material deterioration over time, internal

leakage of vacuum, oil, and coolant may occur.

INTAKE MANIFOLD REFERENCE RECOMMENDED GASKET

5419 (None) Edelbrock #7201 Port: 1.28” x 2.09”, .060” Thickness

A-Carburetor will work with non-EGR or pre-emission control systems.

I-Carburetor has no provisions for evaporative canister.

CARBURETOR (Qty. 3) REFERENCE PARTS REQUIRED FOR INSTALLATION

Rochester 2GC Type (2bbl) A, I Custom throttle linkage required, refer to CAUTION above for details.

NOTE: To ensure maximum performance and a proper seal, Edelbrock gaskets which are

specifically designed and manufactured for use with Edelbrock parts must be used.

Catalog #5419

Rev. 5/05 - RS/mc ©2005 Edelbrock Corporation

Brochure #63-0402Page 2of 2

•PREP AND TUNING FOR POWER:

1. Specific applications may show an increase in power by tuning the fuel mixture.

2. Aftermarket distributor curve kits may be used with this intake manifold. HEIdistributors WILL NOT fit.

3. Use modified or high performance cylinder heads such as our Performer or Performer RPM.

4. Installation of aftermarket headers, camshafts or both may lean carburetor calibration. Should this condition occur,

recalibrate with a richer jet.

•CAMSHAFT AND HEADERS: Three-Deucemanifolds are compatible with aftermarket camshafts and headers. Header primary

tube diameter should be 1-5/8” to 1-3/4" depending on the specific engine combination. Edelbrock has developed two

camshafts for use with this intake manifold - Performer-Plus #2103 or Torker-Plus #5002. Please check the catalog or website

for rpm and application guidelines.

INSTALLATION INSTRUCTIONS

1) Use only recommended intake gaskets set when installing this intake manifold.

2) Fully clean the cylinder head intake flanges and the engine block end seal surfaces.

3) Apply Edelbrock Gasgacinch sealant P/N 9300 to both cylinder head flanges and to the cylinder head side of

the gaskets, allow to air dry, and attach the intake gaskets.

4) Do not use cork or rubber end seals. Use RTV silicone sealer instead. Apply a ¼" high bead across each block

end seal surface, overlapping the intake gasket at the four corners. This method will eliminate end seal

slippage.

5) Install the intake manifold and hold-down bolts. Torque all of the manifold bolts in two steps by the sequence

shown in Figure 1 to 25 ft/lbs.

Edelbrock Corporation • 2700 California St. • Torrance, CA 90503

Tech Line: 800-416-8628 • E-Mail: Edelbrock@Edelbrock.com

Figure 2 - 262-400 c.i.d. Small Block Chevy Firing Order

Firing Order: 1-8-4-3-6-5-7-2

Turn Distributor Counter-Clockwise to Advance Timing

Figure 1 - 262-400 c.i.d. Small Block Chevy Torque Sequence

Torque Bolts to 25 ft/lbs.

87910 23

12 6

511 1

4