Edgecore Networks ECWO3324 802.11b/g/n Outdoor 2.4GHz Access Point User Manual Quick Start Guide

Edgecore Networks Corporation 802.11b/g/n Outdoor 2.4GHz Access Point Quick Start Guide

Contents

User manual

– 1 –Quick Start Guide802.11ac Outdoor Stand-Alone/Cloud-Based Access PointECWO3300, 4300, 5300 SeriesThe ECWO3300/4300/5300 Series are a family of single- and dual-band (2.4/5 GHz) access points (APs) that are housed in a waterproof enclosure for mounting outdoors. The units include a built-in mounting bracket for attaching to a 1.5 to 6-inch pole and they can be powered through their Ethernet cable connection from a power injector module that is installed indoors.The ECWO3300/4300/5300 Series includes these models:ECWO3320 — 2.4 GHz stand-alone AP with internal antennasECWO3320-L — 2.4 GHz controller-based AP with internal antennasECWO3324 — 2.4 GHz stand-alone AP with external antennasECWO3324-L — 2.4 GHz controller-based AP with external antennasECWO4320 — 5 GHz stand-alone AP with internal antennasECWO4320-L — 5 GHz controller-based AP with internal antennasECWO4324 — 5 GHz stand-alone AP with external antennasECWO4324-L — 5 GHz controller-based AP with external antennasECWO5320 — Dual-band stand-alone AP with 5 GHz internal antennasECWO5320-L — Dual-band controller-based AP with 5 GHz internal antennasECWO5324 — Dual-band stand-alone AP with external antennasECWO5324-L — Dual-band controller-based AP with external antennas Note: For Safety and Regulatory information, refer to the Safety and Regulatory Information document included with the AP.E052014-CS-R01150200000891Awww.edge-core.comECWO3320-C — 2.4 GHz cloud-based AP with internal antennasECWO3324-C — 2.4 GHz cloud-based AP with external antennasECWO4320-C — 5 GHz cloud-based AP with internal antennasECWO4324-C — 5 GHz cloud-based AP with external antennasECWO5320-C — Dual-band cloud-based AP with 5 GHz internal antennasECWO5324-C — Dual-band cloud-based AP with external antennas
– 1 –Safety and Regulatory Information802.11ac Outdoor Stand-Alone/Cloud-Based Access PointECWO3300, 4300, 5300 SeriesThis document provides information on switch safety, regulatory statements and compliances. It includes these sections:◆“Compliances and Safety Statements” on page 1◆“Warnings and Cautionary Messages” on page 7Compliances and Safety StatementsFCC Class B This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:◆Reorient or relocate the receiving antenna◆Increase the separation between the equipment and receiver◆Connect the equipment into an outlet on a circuit different from that to which the receiver is connected◆Consult the dealer or an experienced radio/TV technician for helpFCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. E052014-CS-R01150200000892Awww.edge-core.com
Safety and Regulatory Information– 2 –This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Operation within the 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range is restricted to an indoor environment. The 5600-5650MHz band is disabled by software during manufacturing and cannot be changed by the end user. This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body.Professional Installation Instructions1. Installation personal This product is designed for specific applications and needs to be installed by a qualified person who has RF and related rules knowledge. The general user shall not attempt to install or change the settings.2. Installation location The product shall be installed at a location where the radiating antenna can be kept 20 cm from nearby persons in normal operation conditions to meet regulatory RF exposure requirements.3. External antenna Use only the antennas that have been approved by the applicant. Non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power, which may lead to the violation of FCC/IC limits and is prohibited.4. Installation procedure Please refer to user's manual for details.5. Warning Please carefully select the installation position and make sure that the final output power does not exceed the limits set forcth in relevant rules. Violation of the rules could lead to serious federal penalties.Instructions d'installation professionnelle1. Installation Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s'y rapportant. L'installation et les reglages ne doivent pas etre modifies par l'utilisateur final.
Safety and Regulatory Information– 3 –2. Emplacement d'installationEn usage normal, afin de respecter les exigences reglementaires concernant l'exposition aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 20 cm entre l'antenne emettrice et les personnes.3. Antenn externe.Utiliser uniiquement les antennes approuvees par le fabricant. L'utilisation d'autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit.4. Procedure d'installationConsulter le manuel d'utilisation.5. AvertissementChoisir avec soin la position d'installation et s'assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales.CE Mark CE Mark Declaration of Conformance for EMI and Safety (EEC)This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.National RestrictionsThis device is intended for home and office use in all EU countries (and other countries following the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:Note: Do not use the product outdoors in France.Country Restriction Reason/RemarkBulgaria None General authorization required for outdoor use and public serviceFrance Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHzMilitary Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012italy None If used outside of own premises, general authorization is requiredLuxembourg None General authorization required for network and service supply(not for spectrum)Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-ÅlesundRussian Federation None Only for indoor applications
Safety and Regulatory Information– 4 –Europe - EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:◆EN 60950-1:2006 + A11: 2009Safety of Information Technology Equipment.◆EN 300 328 V1.7.1: 2006-10Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using wide band modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive.◆EN 301 489-17 V1.8.1/ 2008-04EN 301 489-17 V2.1.1/ 2009-05Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment.◆EN 55022: 2006 + A1: 2007Limits and methods of measurement of radio disturbance characteristics of information technology equipment.◆EN 55024: 1998 + A1: 2001 + A2: 2003Information technology equipment immunity characteristics limits and methods of measurement.◆EN 62311: 2008Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz - 300 GHz).This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 - 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.
Safety and Regulatory Information– 5 –The Declaration of Conformity (DoC) can be obtained from www.edge-core.com -> support -> download -> declarations & certifications.This equipment may be operated in:BulgarianБългарскиС настоящето, Edge-Core декларира, че това безжично устройство е в съответствие със съществените изисквания и другите приложими разпоредби на Директива 1999/5/EC.CzechČeskyEdge-Core tímto prohlašuje, že tento Radio LAN device je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.DanishDanskUndertegnede Edge-Core erklærer herved, at følgende udstyr Radio LAN device overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EFDutchNederlandsHierbij verklaart Edge-Core dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EGBij deze Accton dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.English Hereby, Edge-Core, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.EstonianEestiKäesolevaga kinnitab Edge-Core seadme Radio LAN device vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.FinnishSuomiValmistaja Edge-Core vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.FrenchFrançaisPar la présente Edge-Core déclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CEGermanDeutschHiermit erklärt Edge-Core, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)Hiermit erklärt Edge-Core die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)GreekΕλληνικήμε την παρουσα Edge-Core δηλωνει οτι radio LAN device συμμορφωνεται προσ τισ ουσιωδεισ απαιτησεισ και τισ λοιπεσ σχετικεσ διαταξεισ τησ οδηγιασ 1999/5/εκ.HungarianMagyarAlulírott, Edge-Core nyilatkozom, hogy a Radio LAN device megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.ItalianItalianoCon la presente Edge-Core dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.LatvianLatviskiAr šo Edge-Core deklarē, ka Radio LAN device atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Safety and Regulatory Information– 6 –NCC Statement(Taiwan)經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。5.25 ~ 5.35GHz 限室內使用 專業安裝警語 ( 固定式點對點操作 )此器材須經專業安裝並限用於固定式點對點操作。” 本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者 ”LithuanianLietuviųŠiuo Edge-Core deklaruoja, kad šis Radio LAN device atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.MalteseMaltiHawnhekk, Edge-Core, jiddikjara li dan Radio LAN device jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.PolishPolskiNiniejszym Edge-Core oświadcza, że Radio LAN device jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.PortuguesePortuguêsEdge-Core declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.RomanianRomanăEdge-Core declară că acest dispozitiv fără fir respectă cerinţele esenţiale precum şi alte dispoziţii relevante ale Directivei 1999/5/EC.SlovakSlovenskyEdge-Core týmto vyhlasuje, že Radio LAN device spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES.SlovenianSlovenskoEdge-Core izjavlja, da je ta radio LAN device v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES.SpanishEspañolPor medio de la presente Edge-Core declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CESwedishSvenskaHärmed intygar Edge-Core att denna Radio LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.TurkishTurkEdge-Core bu kablosuz cihazın temel gereksinimleri ve 1999/5/EC yonergesindeki ilgili koşulları karşıladığını beyan eder.
Safety and Regulatory Information– 7 –Warnings and Cautionary MessagesWarning: This product does not contain any serviceable user parts.Warning: Installation and removal of the unit must be carried out by qualified personnel only.Warning: When connecting this device to a power outlet, connect the field ground lead on the tri-pole power plug to a valid earth ground line to prevent electrical hazards.Caution: Wear an anti-static wrist strap or take other suitable measures to prevent electrostatic discharge when handling this equipment.Caution: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Caution: Use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.Caution: The planning and installation of the AP requires professional personnel that are trained in the installation of radio transmitting equipment. The user is responsible for compliance with local regulations concerning items such as antenna power, use of lightning arrestors, grounding, and radio mast or tower construction. Therefore, it is recommended to consult a professional contractor knowledgeable in local radio regulations prior to equipment installation.Caution: Do not install the power injector outdoors. The unit is for indoor installation only.Caution: Install lightning protection at the power injector end of the Ethernet cable, use a lightning arrestor immediately before the cable enters the building.Caution: Be sure that grounding is available and that it meets local and national electrical codes. Grounding the AP must be performed by a professional installer.Caution: Grounding the outdoor-rated Ethernet cable must be performed by a professional installer in conformance with local safety regulations.
Quick Start Guide– 2 –Follow the steps in this guide to install the AP in your network.Caution: The planning and installation of the AP requires professional personnel that are trained in the installation of radio transmitting equipment. The user is responsible for compliance with local regulations concerning items such as antenna power, use of lightning arrestors, grounding, and radio mast or tower construction. Therefore, it is recommended to consult a professional contractor knowledgeable in local radio regulations prior to equipment installation.1. Unpack the AP Unpack the AP and check the package contents.◆ECWO3300, 4300, or 5300 Series Outdoor Access Point◆Pole-mounting kit — includes two steel-band clamps◆PoE power injector with power cord — either US, Continental Europe or UK◆Documentation —Quick Start Guide and Regulatory and Safety Information2. Mount the AP After planning your installation, mount the unit on a pole, mast, or tower using the included two steel-band clamps. Also install the external antennas required for your wireless service.Pole MountingFeed the steel-band clamps through the integrated pole-mount bracket points on the back of the AP.Fasten the steel-band clamps around the pole to secure the AP to the pole.1212
Quick Start Guide– 3 –Note: The number of available 2.4 GHz or 5 GHz external antenna connectors depends on the specific model.3. Connect Cables Connect outdoor-rated Ethernet cable to the 1000BASE-T RJ-45 ETH0 (PoE) port on the unit. 4. Connect Power Install the PoE power injector indoors. Connect the power injector to the Ethernet cable from the AP, to a port on a local LAN switch, and then to an AC power source.Caution: The power injector module is designed for indoor use only. Never mount the power injector outside with the AP unit. Attach External AntennasRemove the front port cover by pushing the locking tab up and then sliding the cover off.Connect external antennas to the AP’s 5 GHz RP-SMA connectors using RF coaxial cable provided in the antenna package.Connect external antennas to the AP’s 2.4 GHz RP-SMA connectors using RF coaxial cable provided in the antenna package.123231 Connect outdoor-rated Category 5e or better cable to the left-side RJ-45 ETH0 (PoE) port.(Optional) Connect a local LAN switch or computer to the right-side ETH1 100BASE-TX RJ-45 port.Pass the cables through the access holes at the bottom of the AP.Replace the port cover on the AP and push the locking tab down to secure it in place.12344321
Quick Start Guide– 4 –Note: Connecting the Ethernet cable from the AP to the injector module powers on the unit.5. Verify AP Operation Verify basic AP operation by checking the system LEDs. The power LED should be on green, the ETH0 port LED on/blinking green, and the 2.4GHz/5GHz wireless LED on/blinking green (2.4 GHz) or blue (5 GHz). Connect the Ethernet cable from the AP to the “POE” port on the power injector.Connect Ethernet cable from the “LAN” port on the power injector to a LAN switch.Connect the power cord to a nearby AC power source (100-240 VAC, 50/60 Hz).123321 2.4GHz/5GHz signal strength LEDs.2.4GHz/5GHz link/activity LED.ETH1 port link/activity LED.ETH0 (PoE) port link/activity LED.Power LED.1234554321
Quick Start Guide– 5 –6. Connect to the WebUser InterfaceThe stand-alone APs offer a web-based management interface for the configuration of all the unit’s features. You can make initial configuration changes by connecting a PC directly to the AP’s ETH1 RJ-45 port. The AP has a default management IP address of 192.168.2.1 and a subnet mask of 255.255.255.0. You must set your PC IP address to be on the same subnet as the AP (that is, the PC and AP addresses must both start 192.168.2.x).Log in to the web interface using the default settings:◆Login Name — root◆Password — admin123For more information on stand-alone AP configuration using the web interface, refer to the Management Guide.For more information on cloud-based AP configuration, refer to the relevant wireless controller documentation.
Quick Start Guide– 6 –Hardware SpecificationsItem SpecificationChassisSize (H x W x D:) 280.86 x 91.85 x 50.35 mm (11.06 x 3.62 x 1.98 inches)Weight 0.75 kg (1.65 lb)Temperature Operating: -20 °C to 65 °C (-4 °F to 149 °F)Storage: -30 °C to 80 °C (-22 °F to 176 °F)Humidity Operating: 15% to 95% (non-condensing)Waterproof/Dustproof IP55Network InterfacesPorts ETH0 (PoE) RJ-45 Port: 1000BASE-T, passive PoEETH1 RJ-45 Port: 100BASE-TX2.4 GHz Radio IEEE 802.11b/g/n5 GHz Radio IEEE 802.11a/n/acRadio Frequencies 2400 ~ 2483.5 MHz2412 ~ 2472 MHz5745 ~ 5825 MHz (China)5180 ~ 5320 MHz (ETSI)5500 ~ 5700 MHz (ETSI)Power SupplyPoE Input Power 24 VDC, 1.0 APower Consumption 24 W maximumPower Injector Module 100-240 VAC, 50-60 Hz, auto-sensingRegulatory CompliancesRadio EN 300 328 V1.8.1:2012EN 301 893 V1.7.1:2012EN 301 489-1 V1.9.2 (2011-09)EN 301 489-7 V1.3.1:2005FCC Part 15C 15.247/15.207 (2.4-2.4835GHz, 5.725-5.850GHz)FCC Part 15E 15.407 (5.150GHz-5.250GHz)Emissions EN 55022 2010+AC:2011EN 61000-3-2 2006+A1:2009+A2:2009FCC Class B Part 15Immunity EN 55024 : 2010EN 61000-4-2 : 2009Safety UL/CUL (CSA/UL60950-1, CSA/UL60950-22)CB (IEC60950-1, IEC60950-22)

Navigation menu