Edifier EDF24 5.8G Wireless Audio Transceiver/Receiver Module User Manual
Edifier International Limited 5.8G Wireless Audio Transceiver/Receiver Module
Edifier >
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2691476 |
| Application ID | dNoBqUOw8ksMzSx7oJ2NiQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 96kB (1199944 bits) |
| Date Submitted | 2015-07-24 00:00:00 |
| Date Available | 2015-07-24 00:00:00 |
| Creation Date | 2015-06-29 20:23:48 |
| Producing Software | |
| Document Lastmod | 2015-07-03 15:56:41 |
| Document Title | User Manual |
| Document Creator |
5.8G Wireless Audio Transceiver/Receiver Module DWHP83 1. Module dimensions and a layout 20mm 40mm 2. 7mm 15mm Model：DWHP83 FCC ID: Z9G-EDF24 IC: 10004A-EDF24 Antenna info Brand: EDIFIER PCB Antenna type: Max Peak gain: 5.36 dBi 3. Feature: DARR83 Wireless Aud dio Process or 5.8GHz RFF Transceive er Embedded d antennas Digital aud dio interfaces (I2S and//or S/PDIF) I2C contro ol interface 26 pins heeader conne ector for poower, digitall audio and control inteerface and GPIOs Built-in 1M MB SPI interrface Flash 4. How to usse this module dded for SouundBar/Wo oofer transfer audio signal DWHP83 was design to embed n the power of the Hosst device. (FFor example, SoundBar/ use, while uuser turn on woofer or oother mobile e device), DWHP83 will pair p automaatically, and transfer audio signal bby the radiated signal. 1. Pin assignm men: TThe device can c be configured as beelow: Pin TX RX 3.3V 3.3 3V GND GN ND MCLK MCLK RF_Pairing _btn AM_ _IFO Pairin ng_LED 24V_EN NABLE INT PAIRING G_LED MUTE EN_B BUF Quick suspend AMP_ _RST DARR83 3_GPIO_3 I2C SDA A MST 10 DARR83_GPIO_15 I2C SCLL MST 11 GND GN ND 12 GND GN ND 13 DARR83_GPIO_24 (MON N_TXD) RF_PAIR R_BTN 14 DARR83_GPIO_14 POWER_SB 15 DARR83_GPIO_16 MON_ _TXB 16 NC NC 17 RF_E ENABLE RF_Reset 18 I2C SCL S SLV NC 19 I2C SDA SLV NC 20 DARR83_G GPIO_12 (Z ) DE_ _5V 21 DARR83_G GPIO_11 (X ) DEV_ _3V3 22 DARR83_GPIO_10_LRCCK DAO1_LR RCLK_RF 23 GND GN ND 24 DARR83_G GPIO_8_SCLLK DAO1_SCLK_RF 25 DARR83_ _SR_RF (Y) DAO1_SR_RF 26 DARR83_SUB_MIX (W W) DAO1_SUB B_MIX_RF Federal Comm municatiion Com mmissio on Interf rference Statemen nt Thiss equipme ent has bee en tested a and found to t comply with w the lim mits for a Class B d digital device, pursuant to Parrt 15 of th he FCC Rules. Theese limits are dessigned to provide rea asonable protection against harmful inteerference in a resiidential insstallation. This equi pment gen nerates, us ses and cann radiate ra adio freq quency en nergy and, if not in nstalled an nd used in accordaance with the insttructions, may cause harmfu ul interferrence to radio com mmunicatio ons. How wever, there is no gu uarantee th hat interference will not occur in a partic cular insttallation. If this equ uipment do oes cause e harmful interferencce to radio o or tele evision rece eption, which can be determine ed by turnin ng the equ ipment off and on, the user iss encourag ged to try tto correct the interference by oone or morre of the following measures: Reorientt or relocatte the rece eiving antenna. Increase e the separration betw ween the equipment and a receivver. Connectt the equip pment into o an outlet on a circuit differennt from tha at to which th he receiver is conneccted. Consult the dealerr or an exp perienced radio/TV te echnician foor help. FCC C Caution: Any changes or m modification ns not exp pressly appproved by the part rty responssible for compliance ccould void the user's authority tto operate this equ uipment. Thiss device co omplies with Part 15 of the FCC C Rules. Operation iss subject to o the follo owing two conditions s: (1) this device ma ay not cause harmfuul interferen nce, and d (2) thiss device must acccept any interference receivved, includ ding inte erference th hat may ca ause undessired opera ation. Thiss device and its antenna(s) must no ot be co-lo ocated orr operating g in con njunction with w any oth her antenn a or transm mitter. PORTANT NOTE: IMP FCC C Radiatio on Exposu ure Statem ment: Thiss equipme ent complie es with FC CC radiatio on exposure limits seet forth for an unccontrolled environme ent. This e equipment should be e installed and opera ated with h minimum m distance 20cm betw ween the ra adiator & your body. Thiss device iss restricted to indoor use when operated i freq quency ran nge. Hz The e final end product must be labe eled in a visible area a with the foollowing " Con ntains TX F 4 ". This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the IC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains IC: 10004AEDF24” any similar wording that expresses the same meaning may be used. The module is limited to OEM installation ONLY. The OEM integrator is responsible for ensuring that the end-user has no manual instruction to remove or install module. The module is limited to installation in mobile application; A separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and difference antenna configurations. There is requirement that the grantee provide guidance to the host manufacturer for compliance with Part 15B requirements.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00 Create Date : 2015:06:29 20:23:48 Creator Tool : Google Modify Date : 2015:07:03 15:56:41+08:00 Metadata Date : 2015:07:03 15:56:41+08:00 Thumbnail Width : 184 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 6633 bytes, use -b option to extract) Producer : Google N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 209.980292 Max Page Size H : 297.038889 Max Page Size Unit : Millimeters Font Name : Calibri, MicrosoftYaHei, FZY1JW--GB1-0 Font Family : Calibri, 微软雅黑, FZY1JW -GB1-0 Font Face : Regular, Regular, -GB1-0 Font Type : Open Type, Open Type, Unknown Font Version : Version 1.02, Version 5.00, Version 5.010;PS 5.005;hotconv 1.0.57;makeotf.lib2.0.21895 Font Composite : False, False, False Font File Name : CALIBRI.TTF, MSYH.TTF, AdobeHeitiStd-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Format : application/pdf Rendition Class : proof:pdf Document ID : uuid:4d1ed016-318e-49d9-ab8c-e2df5f5305c2 Instance ID : uuid:76a3bd85-92af-43db-8877-d026517a6b24 Page Count : 5 Creator : Adobe Illustrator(R) 15.0 For : tech.tech09, Title : 5.8 模组使用说明书 加FCC IC 警告语.pdf Bounding Box : 0 0 596 842 Container Version : 11 Creator Version : 15 Image Height : 842 Image Width : 596 Image Size : 596x842 Megapixels : 0.502EXIF Metadata provided by EXIF.tools