Edimax Technology Co 9572381208 150N WLAN Dual Band Concurrent Router User Manual

Edimax Technology Co Ltd 150N WLAN Dual Band Concurrent Router

user manual

Wireless 150N Dual Band Concurrent Repeater User Manual Version: 1.0a (Aug, 2012)
COPYRIGHT Copyright ©2011/2012 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents thereof without obligation to notify any person of such revision or changes.
Federal Communication Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio technician for help. FCC Caution This equipment must be installed and operated in accordance with provided instructions and a minimum 20 cm spacing must be provided between computer mounted antenna and person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate equipment. Federal Communication Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches) during normal operation. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment version marketed in US is restricted to usage of the channels 1-11 only. For operation within 5.15 ~ 5.25GHz frequency range, it is restricted to indoor environment.
R&TTE Compliance Statement This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000. Safety This equipment is designed with the utmost care for the safety of those who install and use it. However, special attention must be paid to the dangers of electric shock and static electricity when working with electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to ensure the safe use of the equipment. EU Countries Intended for Use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United Kingdom. The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and Switzerland. EU Countries Not intended for use None.
C A T A L O G Chapter I: Product Information ...................................................................... 1 1-1 Introduction and safety information ................................................................ 1 1-2 Safety Information ........................................................................................... 2 1-3 System Requirements ...................................................................................... 3 1-4 Package Contents ............................................................................................. 4 1-5 Familiar with your new wireless repeater ........................................................ 5 CHAPTER II: Setup your Repeater ............................................................ 8 2-1 Quick Installation Guide .................................................................................. 8 2-1-1 Hardware WPS button setup ................................................................ 9 2-1-2 Web browser quick setup ................................................................... 11 2-2 Advanced setup .............................................................................................. 16 2-2-1 WPS Setting ....................................................................................... 16 2-2-2 Advance Settings ................................................................................ 16 Chapter X: Appendix ................................................................................... 20 5-1 Configuring TCP/IP on PC ............................................................................ 20 5-1-1 Windows XP IP address setup: ........................................................... 20 5-1-2 Windows Vista/Windows 7 IP address setup: ..................................... 21 5-2 Specification .................................................................................................. 24 5-3 Glossary ......................................................................................................... 26
1 Chapter I: Product Information 11Introductionandsafetyinformation Thank you for purchasing this mini 802.11a/b/g/n wireless repeater! The ultra-compact design with power built-in allows you to install this repeater everywhere, and the dual-band wireless providing excellent network performance to extend the Wi-Fi signal and wireless coverage. Other features of this wireless repeater including:  Extend the wireless signal inside your home or office.  Ultra-compact design while maintaining excellent network performance.  Dual-band provide user to the best compatibility to the wireless router.  LED signal indicator to easily realize the best location placement to extend WiFi signal and secure better wireless performance.  The device can support Repeater mode and AP client mode  WPS (Wi-Fi Protected Setup) hardware button for easy installation and secure wireless security.
2 12SafetyInformation In order to keep the safety of users and your properties, please follow the following safety instructions: 1. This wireless repeater is designed for indoor use only. DO NOT expose this device to direct sun light, rain, or snow. 2. DO NOT put this at or near hot or humid places, like kitchen or bathroom. Also, do not left this Wireless repeater in the car in summer. 3. Do not allow kids to put any small parts of this wireless repeater in their mouth, and it could cause serious injury or could be fatal. If they throw this wireless repeater, it will be damaged. PLEASE KEEP THIS WIRELESS REPEATER OUT THE REACH OF CHILDREN! 4. This Wireless repeater will become hot when being used for long time (This is normal and is not a malfunction). DO NOT put the Wireless repeater on a paper, cloth, or other flammable objects after the Wireless repeater has been used for a long time. 5. There’s no user-serviceable part inside the Wireless repeater. If you found that the Wireless repeater is not working properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the Wireless repeater by yourself, warranty will be void. 6. If the Wireless repeater falls into water, DO NOT USE IT AGAIN BEFORE YOU SEND THE CARD TO THE DEALER OF PURCHASE FOR INSPECTION.
3 13SystemRequirements  Wireless network card which is compatible with 802.11b/g/n or 802.11a/b/g/n wireless network standard.  Windows 2000, 2003, XP, Vista, or Windows 7 operating system  CD-ROM drive  At least 100MB of available disk space
4 14PackageContents Before you start to use this wireless repeater, please check if there’s anything missing in the package, and contact your dealer of purchase to claim for missing items: □ Wireless Repeater (1 pcs) …………………………..…………… 1 □ Quick Installation Guide (1 pcs) …………………………………. 2 □ User Manual CDROM (1 pcs) …………………………………… 3
5 15Familiarwithyournewwirelessrepeater Interface Descriptions Item Item Name Description A LAN 10/100Mbps Ethernet LAN Port with Auto-MDI/MDI-X. Connecting to computer, switch or hub for local network sharing. B WPS / Reset button This button support 2 functions: 1. Hold the button 2 seconds to start WPS function 2. Hold the button 10 seconds to reset all the values to the factory default. C ON/OFF switch If you want to switch off the repeater, switch it to Off mode. ABC
6 LED Definitions LED Color LED Status Description 2.4G Signal Amber Steady ON Good signal reception (signal strength 100%~50%). Blinking Normal signal reception Slow blinking (50%~25%) Poor signal reception Quick blinking (<25%) Off Wireless network is switched off/ or LED off mode. 5G Signal Amber Steady ON Good signal reception (signal strength 100%~50%). Blinking Normal signal reception Slow blinking (50%~25%) Poor signal reception Quick blinking (<25%) Off Out of signal or disconnected/ or LED off mode. Power Green Steady ON Power is turned on. In LED off mode. (except power LED is on, other LEDs are off *) *If user selects to enable “LED OFF
7 mode”, power LED On/Off depends on user’s selection, user can select to leave only power LED on or turn off all LEDs including this power LED. Slow Blinking Ready for “Reset to factory default”, power LED is blinking. Off power is turned off. WPS Green Steady ON When WPS connection is successful, turn on for 5 minutes. Blinking WPS is in progress of waiting router’s connection, blinking (0.2 second on, 0.1 second off) for 2 minutes. Quick blinking WPS error, blinking (0.1 second on, 0.1 second off) Off NO WPS is in progress/ LED off modeLAN Green Steady ON LAN port is connected. Blinking LAN port is active (transferring or receiving data). Off LAN port is not connected/ or LED off mode 
8 CHAPTERII:  SetupyourRepeaterThis repeater is your Wi-Fi range extender! It can extend your wireless signal and coverage and help you to solve wireless dead zone problem. This chapter will show you how to quickly install this device by using quick setup and web UI. 21QuickInstallationGuideFor the first time setup and easy installation, you can move this device close to the Wireless Broadband Router or wireless router you wish to connect, after installation done and wireless connection is built, you can move this repeater device to the place you wish to use. Insert this device into power outlet on the wall, and switch wireless repeater’s power switch to ‘ON’ (1). You should see ‘Power’ LED light up in few seconds (2). If not, please check if the power outlet you’re using is working. You can build wireless connection via ‘Hardware WPS button’ or ‘Web browser’. If your wireless router supports ‘WPS button’, we recommend you to use WPS button to establish connection, it is the fast and secure way without computer. Using WPS button - please go to section 2-1-1 Using Web browser - please go to section 2-1-2 (2)(1)
9 211HardwareWPSbuttonsetup (1) Press and hold WPS button on repeater for 2 seconds, ‘WPS’ LED will start flashing. (2) Press WPS button on the wireless router you wish to connect within 2 minutes. WPS LEDWPS buttonNOTE: this WPS button position on wireless router is for example, different device may have different WPS button position.
10 (3) If WPS connection is successfully established, ‘WPS’ LED will light for 5 minutes; if ‘WPS’ LED flashes fast, there’s something error, please wait for 2 minutes until ‘WPS’ LED off, and try from step(1) again. When connection is created, the 5G or 2.4G signal LED will turn on. (4) Please move repeater to the place you wish to use (a better place will be the center of your house) and insert this repeater into power outlet on the wall, the wireless connection will be established automatically. You can check “Wireless signal LED” status to understand signal reception level. Steady light: Excellent, Flash: Good, Fast flash: poor. The quick installation setup is completely done, you can refer to ‘2-2 Repeater mode Advanced Settings’ to login in web UI for other advanced settings. WPS LEDWireless signal LEDNOTE: If the Signal LED is off, it means this place is out of the wireless signal of your wireless router, please move this repeater closer to wireless router until repeater device can receive signal from wireless router and extend its signal.
11 212Webbrowserquicksetup Before you can connect to the repeater and start configuration procedures, your computer must be able to get an IP address automatically (use dynamic IP address). If it’s set to use static IP address, or you’re unsure, please refer to ‘Chapter X: Appendix, 5-1 Configuring TCP/IP on PC’ to set your computer to use dynamic IP address. (1)Use Ethernet cable to connect your computer’s Ethernet port and wireless repeater’s Ethernet port. Or use your computer’s wireless configuration utility to search for wireless router named ‘repeater0003’ and get connected. (The default SSID of this repeater device is ‘repeater0003’, 0003 is an example, it is the last 4 digits of device MAC number. Each device has different MAC number, please find it on your device label.) NOTE: this default SSID ‘repeater0003” is for example, different device may have different last 4 digits.
12 If you are using wireless connection in Windows 7 and encountered the following screen, please click “Connect the network without setting it up” on the blue line then you can successfully link to repeater. Do NOT click “OK “. In case you click ‘OK’, Windows 7 will ask for security key, please click “Cancel” to back to this page. (2) Open web browser, it will redirect to web UI setting page. (or you can input the default IP address ‘http://repeater0003’ in address bar) (3)Wireless repeater will prompt you to input username and password. Default username is ‘admin’ and password is ‘1234’. Click ‘OK’ button to continue. NOTE: this ‘repeater0003” is for example, 0003 is the last 4 digits of device MAC number. Each device has different MAC number, please find it on your device label.) You can also input default IP ‘http://192.168.2.254 instead of repeaterxxxx if your PC is not Windows OS.
13 (4)All wireless routers nearby will be displayed on the list. Select one wireless router you want to connect and click ‘Next’ button to continue. If the wireless router you wish to connect does not appear here, please click ‘Refresh’ until it appears on the list, or try to move wireless repeater closer to the wireless router you wish to connect. If you want to connect to a hidden wireless router, you can select to input SSID manually.
14 (5)You can select the connect frequency to wireless router by enable the option on the bottom of this page. (6)You’ll be prompted to input wireless router’s wireless security key, input it in ‘KEY’ field and click ‘Next’ to continue. (7) It will start to verify the wireless key with your associated wireless router and show you result within 20 seconds. Please follow the instruction to continue setup. (8) When key is correct, wireless repeater will display the connection information for you. ‘Device SSID’ will be XXX_YGre (XXX is the SSID of the wireless
15 router you connected, Y is the wireless band) We recommend you to copy your ‘firmware URL’ (for example: http://repeater.setup ) to you bookmark for quickly login into setting page next time. (9)Please wait for few seconds for wireless repeater to reboot. (10) After reboot complete, you can close browser and use your computer to connect to this repeater by the SSID you set in last step and start using network. NOTE: After the wireless connection of this repeater and wireless router is built, repeater is DHCP client and will get IP address from wireless router automatically. If you want to login Web UI of repeater, please refer to ‘2-2 Repeater mode Advanced Settings’ for more functions or learn how to login web UI again.
16 22AdvancedsetupAfter you connect to the repeater from wireless, Please open the browser, and input the URL as you copied in the quick setup (default: http://repeater.setup ) 221WPSSettingYou can enable or disable WPS function, and also start WPS with software PBC (Push Button Communication) or PIN method in this page 222AdvanceSettingsA. WLAN 2,4G Settings: Setup extended SSID, Encryption and channel to 2.4G connection manually, you can also disable the 2.4G radio in this page.
17 B. WLAN 5G Settings: Setup extended SSID, Encryption and channel to 5G connection manually, you can also disable the 5G radio in this page. C. MAC address filtering: It’s a security settings for access control, you can deny the user with specified MAC in the list, please follow the ways the setup the MAC address filtering: a. Enable the option “Enable Wireless Access Control” b. Fill in the MAC address ( 10 characters) and comments (not necessary) in the slot on the bottom of this page. c. Press “Add” button to increase the MAC address to the table. d. Press “Apply” button to make it effect. e. In the MAC address table, you can select one or select all to delete in the list .
18 D. Admin Utility a. Password settings: Change the default password to login the repeater. b. Management IP: The IP address to login the repeater, You can select “Obtain the IP address automatically” (default value) or set the IP address manually by select “Use the following IP address” c. DHCP Server: Setup the DHCP server manually, it’s disable in the default, if you want to setup this function, you select “Use the following IP address” in the Management IP option. E. Configuration :
19 a. Configuration Tool: to save (download) , upload or reset all the settings to factory default value here. b. WEB Upgrade: to use the “Browse” button to select the firmware file, then press “APPLY” button, you can start to update the firmware to this repeater, while you update the firmware, please do not turn off the power of the repeater. c. Reset: Reset this repeater without change any settings.
20 ChapterX:Appendix51ConfiguringTCP/IPonPC511WindowsXPIPaddresssetup: 1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-click Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection, Local Area Connection Status window will appear, and then click ‘Properties’
21 2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server address automatically’, then click ‘OK’. 512WindowsVista/Windows7IPaddresssetup: 1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select ‘Properties’. Local Area Connection Properties window will appear, select ‘Internet Protocol Version 4 (TCP / IPv4), and then click ‘Properties’
22 2. Select ‘Obtain an IP address automatically’ and ‘Obtain DNS server address automatically’, then click ‘OK’.
23
24 52SpecificationSoC + RF: Realtek RTL8196CS+ RTL8192DR Flash: 4MB SDRAM: 32MB LAN Port: 10/100M UTP Port x 1 Power: 5VDC, 1.2A Switching Power Module Inside Dimension: 46.5(W) x 73(H) x 41(D) mm excluding power plug Transmit Power: 2.4G Data Rate Channel Power (±1.5dBm) 11b 1Mbps Ch 7 18 dBm 11Mbps Ch 7 16 dBm 11g 6Mbps Ch 7 16 dBm 54Mbps Ch 7 14 dBm 11n20M MCS0 Ch 7 15 dBm MCS7 Ch 7 13 dBm 11n40M MCS0 Ch 7 15 dBm MCS7 Ch 7 13 dBm 5G Data Rate Channel Power (±1.5dBm) 11a 6Mbps Ch36 12 dBm Ch64 12 dBm Ch100 13 dBm Ch140 13 dBm Ch149 13 dBm Ch165 13 dBm 54Mbps Ch36 13 dBm Ch64 12 dBm Ch100 13 dBm Ch140 13 dBm Ch149 13 dBm Ch165 13 dBm 11a20M MCS0 Ch36 11 dBm
25 Ch64 11 dBm Ch100 11 dBm Ch140 11 dBm Ch149 11 dBm Ch165 11 dBm MCS7 Ch36 11 dBm Ch64 11 dBm Ch100 11 dBm Ch140 11 dBm Ch149 11 dBm Ch165 11 dBm 11a40M MCS0 Ch36 11 dBm Ch64 11 dBm Ch100 11 dBm Ch140 11 dBm Ch149 11 dBm Ch165 11 dBm Temperature: 32~104°F (0 ~ 40°C) Humidity: 10-90% (NonCondensing) Certification: FCC, CE
26 53Glossary 1. What is the IEEE 802.11g standard? 802.11g is the new IEEE standard for high-speed wireless LAN communications that provides for up to 54 Mbps data rate in the 2.4 GHz band. 802.11g is quickly becoming the next mainstream wireless LAN technology for the home, office and public networks. 802.11g defines the use of the same OFDM modulation technique specified in IEEE 802.11a for the 5 GHz frequency band and applies it in the same 2.4 GHz frequency band as IEEE 802.11b. The 802.11g standard requires backward compatibility with 802.11b. The standard specifically calls for: A. A new physical layer for the 802.11 Medium Access Control (MAC) in the 2.4 GHz frequency band, known as the extended rate PHY (ERP). The ERP adds OFDM as a mandatory new coding scheme for 6, 12 and 24 Mbps (mandatory speeds), and 18, 36, 48 and 54 Mbps (optional speeds). The ERP includes the modulation schemes found in 802.11b including CCK for 11 and 5.5 Mbps and Barker code modulation for 2 and 1 Mbps. B. A protection mechanism called RTS/CTS that governs how 802.11g devices and 802.11b devices interoperate. 2. What is the IEEE 802.11b standard? The IEEE 802.11b Wireless LAN standard subcommittee, which formulates the standard for the industry. The objective is to enable wireless LAN hardware from different manufactures to communicate. 3. What does IEEE 802.11 feature support? The product supports the following IEEE 802.11 functions: z CSMA/CA plus Acknowledge Protocol z Multi-Channel Roaming z Automatic Rate Selection z RTS/CTS Feature z Fragmentation z Power Management 4. What is Ad-hoc? An Ad-hoc integrated wireless LAN is a group of computers, each has a Wireless LAN card, Connected as an independent wireless
27 LAN. Ad hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation. 5. What is Infrastructure? An integrated wireless and wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to central database, or wireless application for mobile workers. 6. What is BSS ID? A specific Ad hoc LAN is called a Basic Service Set (BSS). Computers in a BSS must be configured with the same BSS ID. 7. What is WEP? WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40 bit shared key algorithm, as described in the IEEE 802 .11 standard. 8. What is TKIP? TKIP is a quick-fix method to quickly overcome the inherent weaknesses in WEP security, especially the reuse of encryption keys. TKIP is involved in the IEEE 802.11i WLAN security standard, and the specification might be officially released by early 2003. 9. What is AES? AES (Advanced Encryption Standard), a chip-based security, has been developed to ensure the highest degree of security and authenticity for digital information, wherever and however communicated or stored, while making more efficient use of hardware and/or software than previous encryption standards. It is also included in IEEE 802.11i standard. Compare with AES, TKIP is a temporary protocol for replacing WEP security until manufacturers implement AES at the hardware level. 10. Can Wireless products support printer sharing? Wireless products perform the same function as LAN products. Therefore, Wireless products can work with Netware, Windows 2000, or other LAN operating systems to support printer or file sharing. 11. Would the information be intercepted while transmitting on air? WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread Spectrum technology, it has the inherent security feature of scrambling. On the software side, WLAN series offer the encryption function (WEP) to enhance
28 security and Access Control. Users can set it up depending upon their needs. 12. What is DSSS? What is FHSS? And what are their differences? Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes frequency in a pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration impulse noise. Direct-sequence spread-spectrum (DSSS) generates a redundant bit pattern for each bit to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip is, the greater the probability that the original data can be recovered. Even if one or more bits in the chip are damaged during transmission, statistical techniques embedded in the radio can recover the original data without-the need for retransmission. To an unintended receiver, DSSS appears as low power wideband noise and is rejected (ignored) by most narrowband receivers. 13. What is Spread Spectrum? Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communication systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread –spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and Frequency Hopping Spread Spectrum (FHSS). 14. What is WPS? WPS stands for Wi-Fi Protected Setup. It provides a simple way to establish unencrypted or encrypted connections between wireless clients and access point automatically. User can press a software or hardware button to activate WPS function, and WPS-compatible wireless clients and access point will establish connection by themselves. There are two types of WPS: PBC (Push-Button Configuration) and PIN code.

Navigation menu