Edimax Technology Co 9574361310 N300 Smart Wi-Fi Extender User Manual

Edimax Technology Co Ltd N300 Smart Wi-Fi Extender

user manual

Download: Edimax Technology Co 9574361310 N300 Smart Wi-Fi Extender User Manual
Mirror Download [FCC.gov]Edimax Technology Co 9574361310 N300 Smart Wi-Fi Extender User Manual
Document ID2218055
Application ID7EIWuiSdUJbhnLy62BksHg==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize215.75kB (2696922 bits)
Date Submitted2014-03-18 00:00:00
Date Available2014-03-18 00:00:00
Creation Date2014-02-12 15:17:19
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2014-03-18 09:26:50
Document Titleuser manual
Document CreatorMicrosoft® Office Word 2007
Document Author: Joey Su

EW-7438RPn Air
User Manual
Product Information
I-1. Package Contents
- EW-7438RPn Air
- CD with multi-language QIG & user manual
- Quick installation guide (QIG)
- Access key card
I-2. System Requirements
- Wi-Fi extender/Wi-Fi bridge mode: Existing 2.4GHz wireless network
- Access point mode: Cable/DSL modem
- Computer with 2.4GHz 802.11/b/g/n Wi-Fi adapter, and web browser for
software configuration (Internet Explorer 8® or above, Google Chrome®,
Firefox® or Safari® latest version)
I-3. Safety Information
In order to ensure the safe operation of the device and its users, please read
and act in accordance with the following safety instructions.
1. The device is designed for indoor use only; do not place it outdoors.
2. Do not place the device in or near hot/humid places, such as a kitchen or
bathroom.
3. Do not pull any connected cable with force; carefully disconnect it from the
EW-7438RPn Air.
4. Handle the device with care. Accidental damage will void the warranty of
the device.
5. The device contains small parts which are a danger to small children under
3 years old. Please keep the device out of reach of children.
6. Do not place the device on paper, cloth, or other flammable materials. The
device may become hot during use.
7. There are no user-serviceable parts inside the device. If you experience
problems with the device, please contact your dealer of purchase and ask
for help.
8. The device is an electrical device and as such, if it becomes wet for any
reason, do not attempt to touch it without switching the power supply off.
Contact an experienced electrical technician for further help.
9. If you smell burning or see smoke coming from the EW-7438RPn Air then
unplug the device immediately, as far as it is safely possible to do so. Call
your dealer of purchase for help.
10. This product should work for a long time, and provide round-the-clock
Wi-Fi service.
I. Installation
1. Plug the EW-7438RPn Air into a power socket and switch it on.
2. The red power LED will flash while the system is booting up. The device is
ready when the red power LED displays on.
3. Use a Wi-Fi device (e.g. computer, tablet, smartphone) to search for a
Wi-Fi network with the SSID “EdimaxEXT.Setup” and connect to it.
If you are using a computer, please disconnect any Ethernet
cables. For mobile devices, iOS 4.3 or Android 4.x or above is
required.
The last two characters of the SSID (EdimaxEXT.Setup**) will be
unique numbers according to your device e.g.”EdimaxEXT.Setup
c1”. Your unique SSID is displayed on the product label along with
the included access key card.
4. Open a web browser and if you do not automatically arrive at the “Get
Started” screen shown below, enter the URL http://edimaxext.setup and
click “Get Started” to begin the setup process.
If you cannot access http://edimaxext.setup, please make sure
your computer is set to use a dynamic IP address. For more
information please refer to VII-1. Configuring your IP address.
5. Select an operating mode for your EW-7438RPn Air and follow the
on-screen instructions for your selected mode to complete setup. Refer to
the appropriate chapter for more guidance on setup for each mode.
II-1.
1.
Wi-Fi Extender Mode
Select your Wi-Fi network from the list and enter the security
key/password. You can also enter a new Wi-Fi network name (SSID) if you
wish. Click “Next” to continue.
By default, the Wi-Fi extender’s new wireless network name
( SSID) is your existing router/access point’s SSID + _2EX. For
example if your router’s SSID is “Your SSID” then the EW-7438RPn
Air ’s SSID will be “Your SSID_2EX”. You can change your
extender’s new SSID in the “Extender Device SSID” field.
If the Wi-Fi network you wish to connect to does not appear, try
clicking “Refresh”.
Do not check “Connect to a hidden network” unless you wish to
connect to a hidden SSID instead.
2.Please wait while the EW-7438RPn Air tests the connection.
If your Wi-Fi extender cannot obtain an IP address (below) from
your existing router/access point then click the “Static IP” button
to assign an IP address to the extender. For more guidance please
refer to the VII-1. Configuring your IP address.
3.When the connection test is complete, click “Apply” to restart the
extender.
4.
Please wait a moment until the extender is ready.
5.A final congratulations screen will indicate that setup is complete. The
EW-7438RPn Air is working and ready for use - the Blue signal strength LED
should display on or flash depending on your signal strength.
6.Please close the browser window. You can now connect to the extender’s
new SSID on a wireless device within range such as a computer,
smartphone or tablet. Do not connect to your router’s SSID instead!
The password for your Wi-Fi extender’s SSID is the same as for
your router’s SSID.
For more advanced configurations, use the browser based
configuration interface (refer to III. Browser Based
Configuration Interface).
II-4. WPS Setup
The WPS button is a quick and easy method to establish a secure connection
between your EW-7438RPn Air and wireless router/access point.
If your wireless device supports WPS (Wi-Fi Protected Setup) then you can use
this method to setup the EW-7438RPn Air in extender mode, instead of the
setup wizard described in II. Installation.
Please do not hold the WPS button for too long – this may reset
your device.
1. Press the WPS button on your wireless router/access point for the correct
length of time to activate its WPS.
Please check the instructions for your wireless device for how long
you need to hold down its WPS button to activate WPS.
2. Within two minutes, press the WPS button on the EW-7438RPn Air for 2 –
5 seconds to activate WPS. The green WPS LED will flash to indicate that
WPS is active.
Press for two
seconds
3. The devices will establish a connection. The green WPS LED on the
EW-7438RPn Air will display on for 30 second then reboot device once.
4. After WPS connection is sucessful, you can see the Blue signal strength
LED should display on or flash depending on your signal strength.
II-5.
Reset to Factory Default Settings
If you experience problems with your extender or if you want to change the
extender to a different operating mode, you can reset the device back to its
factory settings. This resets all settings back to default.
1.
Press and hold the WPS/Reset button for at least 10 seconds until the red
power LED is flashing.
2.Wait for the extender to restart. The extender is ready for setup when the
red power LED displays on.
10
II. Browser Based Configuration Interface
After you have setup the EW-7438RPn Air as detailed in II. Installation or the
included Quick Installation Guide, you can use the browser based
configuration interface to configure advanced settings.
Please ensure that your computer is set to use a dynamic IP
address. Refer to VII-1. Configuring your IP address for more
information.
III-1.
Login
1.
To access the browser based configuration interface enter
http://edimaxext.setup into the URL bar of a browser on a network device
connected to the same Wi-Fi network as the EW-7438RPn Air.
2.
You will be prompted for a username and password. The default
username is “admin” and the default password is “1234”.
11
3.
You will arrive at the “Status and Information” screen. Use the menu
down the left side to navigate.
12
III. Extender Mode
IV-1.
Home
The “Status” page displays basic system information
about the device, arranged into three categories:
system, wireless configuration & LAN configuration.
Screenshots displayed are examples.The information shown on
your screen will vary depending on your configuration.
Uptime
Displays the total time since the device was
turned on.
13
Hardware Version
Firmware Version
Mode
ESSID
Channel Number
Security
BSSID (MAC)
Associated Clients
Status
Signal Strength
IP Address
Subnet Mask
Default
Gateway
MAC address
Displays the hardware version.
Displays the firmware version.
Displays the operating mode.
Displays the EW-7438RPn Air’s ESSID,
sometimes also known as SSID. The
ESSID/SSID is the name used to identify a
wireless network.
Displays the current wireless channel number.
Displays the current wireless security setting.
Displays the device’s BSSID. The BSSID
identifies the EW-7438RPn Air in the network,
and is the same as the device’s MAC address.
Displays the number of clients connected to
the EW-7438RPn Air. Click “Show Active
Clients” to display a new window showing
information about wireless clients.
Displays the current connection status of the
EW-7438RPn Air.
Displays the signal strength for the specified
Wi-Fi network.
Displays the IP address of this device.
Displays the subnet mask of the IP address.
Displays the IP address of the default
gateway.
Displays the device’s MAC address. The MAC
address is a unique, fixed ID for this device, it
cannot be modified.
14
IV-2.
iQ Setup
You can run the setup wizard again to reconfigure the
basic settings of the device. Please refer to II-1. Wi-Fi
Extender Mode Step 2 onwards for guidance.
If you wish to change the operating mode, please reset the
EW-7438RPn Air back to factory default settings.
15
IV-3.
WPS Settings
Wi-Fi Protected Setup is a simple way to establish
connections between WPS compatible devices. When
WPS is activated in the correct manner and at the correct time for two
compatible devices, they will automatically connect. PIN code WPS includes
the use of a PIN code between the two devices for verification.
The WPS Settings page displays settings for WPS between your extender and a
wireless client. For WPS Setup between your extender and router/access
point, please use the WPS button as described in II-4. WPS Setup.
WPS Status
Self PIN Code
Configuration
Mode
Configure via Push
Button
Input Client PIN
Code
Displays “Configured” or “unConfigured”
depending on whether WPS and SSID/security
settings for the device have been configured or
not, either manually or using the WPS button.
Displays the WPS PIN code of the device.
The configuration mode of the device’s WPS
setting is displayed here. “Registrar” means
the device acts as an access point for a wireless
client to connect to and the wireless client(s)
will follow the device’s wireless settings.
Click “Start PBC” (Push-Button Configuration)
to activate WPS on the access point. WPS will
be active for 2 minutes.
Enter the wireless client’s PIN code here and
click “Start PIN” to activate PIN code WPS.
Refer to your wireless client’s documentation if
you are unsure of its PIN code.
16
IV-4.
Wireless Advanced
In “Wireless Advanced” you adjust the power output
and LED operation of the EW-7438RPn Air. The
submenu also allows you to configure security, as well
as various administrative and management functions.
This product should work for a long time, and provide
round-the-clock Wi-Fi service.
Tx Power
Enable LED Off
Mode
You can adjust the level of wireless output
power as a percentage. Depending on the size
of your location and required coverage, you
may not require 100% output power.
Reducing the output power can enhance
security since your Wi-Fi signal will not extend
to potential malicious/unknown users in
distant areas.
Check this box to enable “LED Off Mode”
which allows you to select “Turn off all LED
indicators” or “Turn off all LED indicators
except the power LED” accordingly.
17
IV-4-1.
WLAN 2.4GHz Security
Broadcast SSID
Device SSID
Security Type
Enable or disable ESSID broadcast. When
enabled, the ESSID will be visible to clients as
an available Wi-Fi network. When disabled,
the ESSID will not be visible as an available
Wi-Fi network to clients – clients must
manually enter the ESSID in order to connect.
A hidden (disabled) ESSID is typically more
secure than a visible (enabled) SSID. WPS
(Wi-Fi Protected Setup) is also disabled when
SSID broadcast is disabled.
This is the name of your Wi-Fi network for
identification, also sometimes referred to as
“SSID”. The SSID can consist of any
combination of up to 32 alphanumerical
characters.
The security/encryption type of your
EW-7438RPn Air’s wireless network is
displayed here. The security/encryption type
is the same as your existing router/access
point.
18
IV-4-2. Administration Utility
You can change the password used to login to the browser-based
configuration interface here. It is advised to do so for security purposes. You
can also configure the EW-7438RPn Air’s IP address.
Please make a note of the new password. In the event that you
forget the password and are unable to login to the browser
based configuration interface, see II-5. Reset to factory default
settings for how to reset the device.
Current Password
Enter your current password.
New Password
Enter your new password.
Confirmed Password Confirm your new password.
IP Address
Subnet Mask
Gateway Address
Specify an IP address here. This IP address will
be assigned to yourEW-7438RPn Air.
Input the subnet mask of the new IP address.
Input the network’s gateway IP address.
19
IV-4-3.
Configuration Tools
The “Configuration Tools” menu allows you to backup the EW-7438RPn Air’s
settings, restore the settings to a previous version or restore the EW-7438RPn
Air back to its factory default state. You can also upgrade the firmware,
reboot the device and export the system log.
Backup Settings
Restore Settings
Restore to Factory
Default
Click “Save” to save the current settings on
your computer as config.bin file.
Click “Browse” to find a previously saved
config.bin file and then click “Upload” to
replace your current settings.
Click “Reset” to restore settings to the factory
default. A pop-up window will appear and ask
you to confirm and enter your log in details.
Enter your username and password and click
“Ok”. See below for more information.
20
Upgrade Firmware
You can upgrade the system firmware to a more recent version. You can
download the latest firmware from the Edimax website. After the upgrade,
the system will restart.
Do not switch off or disconnect the device during a firmware
upgrade, as this could damage the device. It is recommended that
you use a computer for a firmware upgrade.
Browse
Open a new window to locate and select the
firmware file in your computer.
21
Reboot
In the event that the router malfunctions or is not responding, then it is
recommended that you restart the device.
Rebooting the EW-7438RPn Air will not affect the current
configuration/settings of the device.
Apply
Click “Apply” to reboot the device. A status
bar will indicate the progress of the reboot
and you will see a confirmation screen when
the reboot is complete.
22
System Log
You can export the system log to a separate file if you require.
Export system log
Click to open a new window and select a
location to save the log file.
23
IV. Appendix
VII-1. Configuring your IP address
For first time access to the URL http://EdimaxEXT.Setup please ensure your
computer is set to use a dynamic IP address. This means your computer can
obtain an IP address automatically from a DHCP server. You can check if your
computer is set to use a dynamic IP address by following VII-1-1. How to
check that your computer uses a dynamic IP address.
Static IP users can also temporarily modify your computer’s IP address to be
in the same IP address subnet e.g. 192.168.9.x (x = 3 – 254) as the
EW-7438RPn Air in order to access http://Edimax.Setup.
The EW-7438RPn Air’s default IP address is 192.168.9.2.
The procedure for modifying your IP address varies across different operating
systems; please follow the guide appropriate for your operating system in
IV-1-2. How to modify the IP address of your computer.
Static IP users please make a note of your static IP before you
change it.
You can assign a new IP address to the device which is within the subnet of
your network during setup or using the browser based configuration interface,
so that you can access the URL http://EdimaxEXT.Setup in future without
modifying your IP address.
Please remember to change your IP address back to its original
value after the device is properly configured.
24
VII-1-1.
How to check that your computer uses a dynamic IP address
Please follow the instructions appropriate for your operating system.
VII-1-1-1. Windows XP
1.
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”. Double-click the “Network and
Internet Connections” icon, click “Network Connections”, and then
double-click “Local Area Connection”. The “Local Area Connection Status”
window will then appear, click “Properties”.
2.
“Obtain an IP address automatically” and “Obtain DNS server address
automatically” should be selected.
25
26
VII-1-1-2. Windows Vista
1.
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”. Click “View Network Status and
Tasks”, then click “Manage Network Connections”. Right-click “Local Area
Network”, then select “Properties”. The “Local Area Connection Properties”
window will then appear, select “Internet Protocol Version 4 (TCP / IPv4)”,
and then click “Properties”.
2.
Select “Obtain an IP address automatically” and “Obtain DNS server
address automatically” should be selected.
27
28
VII-1-1-3. Windows 7
1.
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”.
2.
Under “Network and Internet” click “View network status and tasks”.
3.
Click “Local Area Connection”.
29
4.
Click “Properties”.
5.
Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
30
6.
Select “Obtain an IP address automatically” and “Obtain DNS server
address automatically” should be selected.
31
VII-1-1-4. Windows 8
1.
From the Windows 8 Start screen, you need to switch to desktop mode.
Move your curser to the bottom left of the screen and click.
2.
In desktop mode, click the File Explorer icon in the bottom left of the
screen, as shown below.
3.
Right click “Network” and then select “Properties”.
32
4.
5.
In the window that opens, select “Change adapter settings” from the left
side.
Choose your connection and right click, then select “Properties”.
33
6.
7.
Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
Select “Obtain an IP address automatically” and “Obtain DNS server
address automatically” should be selected.
34
35
VII-1-1-5. Mac OS
1.
2.
Have your Macintosh computer operate as usual, and click on “System
Preferences”.
In System Preferences, click on “Network”.
3.
Click on “Wi-Fi” in the left panel and then click “Advanced” in the lower
right corner.
4.
Select “TCP/IP” from the top menu and “Using DHCP” in the drop down
menu labeled “Configure IPv4” should be selected.
36
37
VII-1-2.
How to modify the IP address of your computer
Please follow the instructions appropriate for your operating system. In the
following examples we use the IP address 192.168.9.20 though you can use
any IP address in the range 192.168.9.x (x = 3 – 254) in order to access iQ
Setup/browser based configuration interface.
Please make a note of your static IP before you change it.
VII-1-2-1.
1.
2.
Windows XP
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”. Double-click the “Network and
Internet Connections” icon, click “Network Connections”, and then
double-click “Local Area Connection”. The “Local Area Connection Status”
window will then appear, click “Properties”.
Select “Use the following IP address”, then input the following values:
Your existing static IP address will be displayed in the “IP
address” field before you replace it. Please make a note of this IP
38
address, subnet mask, default gateway and DNS server
addresses.
IP address: 192.168.9.20
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
39
VII-1-2-2.
1.
2.
Windows Vista
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”. Click “View Network Status and
Tasks”, then click “Manage Network Connections”. Right-click “Local Area
Network”, then select “Properties”. The “Local Area Connection Properties”
window will then appear, select “Internet Protocol Version 4 (TCP / IPv4)”,
and then click “Properties”.
Select “Use the following IP address”, then input the following values:
Your existing static IP address will be displayed in the “IP
address” field before you replace it. Please make a note of this IP
address, subnet mask, default gateway and DNS server
addresses.
IP address: 192.168.9.20
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
40
VII-1-2-3.
1.
Windows 7
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”.
41
2.
Under “Network and Internet” click “View network status and tasks”.
3.
Click “Local Area Connection”.
42
4.
Click “Properties”.
5.
Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
43
6.
Select “Use the following IP address”, then input the following values:
Your existing static IP address will be displayed in the “IP
address” field before you replace it. Please make a note of this IP
address, subnet mask, default gateway and DNS server
addresses.
IP address: 192.168.9.20
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
44
45
VII-1-2-4.
Windows 8
1.
From the Windows 8 Start screen, you need to switch to desktop mode.
Move your curser to the bottom left of the screen and click.
2.
In desktop mode, click the File Explorer icon in the bottom left of the
screen, as shown below.
46
3.
4.
Right click “Network” and then select “Properties”.
In the window that opens, select “Change adapter settings” from the left
side.
47
5.
Choose your connection and right click, then select “Properties”.
6.
Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
48
7.
Select “Use the following IP address”, then input the following values:
Your existing static IP address will be displayed in the “IP
address” field before you replace it. Please make a note of this IP
address, subnet mask, default gateway and DNS server
addresses.
IP address: 192.168.9.20
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
49
VII-1-2-5.
1.
2.
Mac
Have your Macintosh computer operate as usual, and click on “System
Preferences”
In System Preferences, click on “Network”.
3.
Click on “Wi-Fi” in the left panel and then click “Advanced” in the lower
right corner.
4.
Select “TCP/IP” from the top menu and select “Manually” from the drop
down menu labeled “Configure IPv4”, then click “OK”.
50
Your existing static IP address will be displayed in the “IP
address” field before you replace it. Please make a note of this IP
address, subnet mask, default gateway and DNS server
addresses.
5.
In the “IPv4 Address” and “Subnet Mask” field enter IP address
192.168.9.20 and subnet mask 255.255.255.0. Click on “OK”.
51
6.
Click “Apply” to save the changes.
52
VII-1-3.
How to Find Your Network Security Key
To find your network security key, please follow the instructions appropriate
for your operating system.
If you are using Windows XP or earlier, please contact your ISP or
router manufacturer to find your network security key.
VII-1-3-1. Windows 7 & Vista
1.
Open “Control Panel” and click on “Network and Internet” in the top
menu.
2.
Click on “View network status and tasks” which is under the heading
“Network and Sharing Center”.
3.
Click on “Manage wireless networks” in the left menu.
53
4.
You should see the profile of your Wi-Fi network in the list. Right click on
your Wi-Fi network and then click on “Properties”.
5.Click on the “Security” tab, and then check the box labeled “Show
characters”. This will show your network security key. Click the “Cancel”
button to close the window.
54
VII-1-3-2. Mac
1.
Open a new Finder window, and select “Applications” from the menu on
the left side. Open the folder labeled “Utilities” and then open the
application “Keychain Access”.
2.
Select “Passwords” from the sub-menu labeled “Category” on the left side,
as shown below. Then search the list in the main panel for the SSID of your
network. In this example, the SSID is “EdimaxWireless” – though your SSID
will be unique to your network.
55
3.
Double click the SSID of your network and you will see the following
window.
4.
Check the box labeled “Show password” and you will be asked to enter
your administrative password, which you use to log into your Mac. Enter
your password and click “Allow”.
56
Your network security password will now be displayed in the field next to
the box labeled “Show password”. In the example below, the network
security password is “edimax1234”. Please make a note of your network
security password.
57
VII-1-4.
How to Find Your Router’s IP Address
To find your router’s IP address, please follow the instructions appropriate for
your operating system.
VII-1-4-1. Windows XP, Vista & 7
1.
Go to “Start”, select “Run” and type “cmd”, then press Enter or click “OK”.
2.
A new window will open, type “ipconfig” and press Enter.
58
3.
Your router’s IP address will be displayed next to “Default Gateway”.
59
VII-1-4-2. Windows 8
1.
From the Windows 8 Start screen, move your curser to the top right
corner of the screen to display the Charms bar.
2.
Click “Search” and enter “cmd” into the search bar. Click the “Command
Prompt” app which be displayed on the left side.
60
3.
A new window will open, type “ipconfig” and press Enter.
61
4.Your router’s IP address will be displayed next to “Default Gateway”.
62
VII-1-4-3. Mac
1.
Launch “System Preferences” and click on “Network”.
2.
If you are using an Ethernet cable to connect to your network, your
router’s IP address will be displayed next to “Router”.
3.
If you are using Wi-Fi, click “Wi-Fi” in the left panel, and then “Advanced”
in the bottom right corner.
63
4.
Click the “TCP/IP” tab and your router’s IP address will be displayed next
to “Router”.
64
VII-2. Connecting to a Wi-Fi network
For help connecting to your device’s Edimax.Setup SSID for initial setup, or to
connect to your device’s new Wi-Fi network (SSID) after setup is complete,
follow the guide below:
Below is an example of how to connect using Windows Vista – the
process may vary slightly for other versions of Windows.
1.
Click the network icon (
to a network”.
2.
Search for the SSID of your EW-7438RPn Air and then click “Connect”. If
you set a password for your network, you will then be prompted to enter it.
or ) in the system tray and select “Connect
65
3.
After correctly entering your password, you will be successfully connected
to the EW-7438RPn Air’s wireless network.
66
VII-3. Troubleshooting
If you are experiencing problems with your wireless extender, please refer to
this troubleshooting guide before contacting your dealer of purchase for help.
Scenario
I can’t log onto the
browser-based
configuration
interface.
Solution
a. Please check that the extender is correctly inserted
into a power socket and check the LEDs on the
front panel. If the extender is initializing after being
switched off or restarted, wait for a 2 minutes and
try again.
b. Make sure you are using the full, correct URL:
http://edimaxext.setup
c. If you are using a MAC or IP address filter, try to
connect the wireless extender using a different
computer.
d. Set your computer to obtain an IP address
automatically (DHCP), and see if your computer can
obtain an IP address.
e. Ensure that all other Wi-Fi/Ethernet adapters are
disabled or disconnected.
f. Password is case-sensitive. Make sure the “Caps
Lock” light is not illuminated.
g. b. If you do not know your password, restore the
device to factory settings.
I can’t establish a
a. If encryption is enabled, please re-check WEP or
connection to my
WPA passphrase settings on your wireless client.
wireless extender.
The password is case-sensitive. Make sure the
“Caps Lock” light is not illuminated.
b. Try moving closer to the wireless extender.
c. Switch off the extender and switch it back on after
10 seconds.
d. Please check that the extender is correctly inserted
into a power socket and check the LEDs on the
front panel.
File downloads are
a. Reset the wireless extender
very slow or
b. Try again later. Your local network may be
frequently
experiencing technical difficulties or very high
interrupted.
usage.
c. Change channel number.
The wireless extender a. It is normal for the wireless extender to heat up
67
is extremely hot.
during frequent use. If you can safely place your
hand on the wireless extender, the temperature of
the device is at a normal level.
b. If you smell burning or see smoke coming from
wireless extender then disconnect the extender
immediately, as far as it is safely possible to do so.
Call your dealer of purchase for help.
My network device
a. Ensure that your broadband router is fully
can’t access the
functional.
Internet.
b. Switch off both your network device and wireless
extender and switch back on again.
c. Ensure that the wireless extender is powered on
(check the PWR LED).
d. On the browser based configuration interface home
page, check “Status” under “Wireless
Configuration”. It should be “Connected” – if it is
“Disconnected” then this means the wireless
extender is not connected to your router/access
point.
My wireless extender The best location to place the Wi-Fi extender is one
has a poor signal
which is an open space, roughly in the middle
from my access
between your router and the Wi-Fi dead zone, and
point/router.
where the Wi-Fi extender LED displays “Excellent”
signal strength.
Can I use the same
SSID as my current
gateway router for
my Wi-Fi extender?
a. Keep the extender away from other radio devices
such as microwaves or wireless telephones.
b. Do not put the extender in the corner of a room or
under/nearby metal.
c. It is recommended to plug the extender directly
into a wall socket.
d. Ensure there are as few obstacles as possible
between the extender and the access point/router.
Yes, but it is not recommended as it will be difficult to
distinguish between two SSIDs with the same name.
68
COPYRIGHT
Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission from Edimax Technology Co., Ltd.
Edimax Technology Co., Ltd. makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability, or fitness for any particular purpose. Any software described in this
manual is sold or licensed as is. Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer) assumes the
entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Edimax Technology Co., Ltd. reserves the right
to revise this publication and to make changes from time to time in the contents hereof
without the obligation to notify any person of such revision or changes.
The product you have purchased and the setup screen may appear slightly different from
those shown in this QIG. The software and specifications are subject to change without
notice. Please visit our website www.edimax.com for updates. All brand and product
names mentioned in this manual are trademarks and/or registered trademarks of their
respective holders.
69
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the
authority to operate equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels
is not possible. This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND
THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual
recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to
ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI
version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and
Switzerland.
EU Countries Not Intended for Use
None
70
EU Declaration of Conformity
English:
This equipment is in compliance with the essential requirements and other relevant
provisions of Directive 2006/95/EC, 2011/65/EC.
Français:
Cet équipement est conforme aux exigences essentielles et autres dispositions de la
directive 2006/95/CE, 2011/65/CE.
Čeština:
Toto zařízení je v souladu se základními požadavky a ostatními příslušnými ustanoveními
směrnic 2006/95/ES, 2011/65/ES.
Polski:
Urządzenie jest zgodne z ogólnymi wymaganiami oraz szczególnymi warunkami
określonymi Dyrektywą UE 2006/95/EC, 2011/65/EC..
Română:
Acest echipament este în conformitate cu cerinţele esenţiale şi alte prevederi relevante ale
Directivei 2006/95/CE, 2011/65/CE.
Русский:
Это оборудование соответствует основным требованиям и положениям Директивы
2006/95/EC, 2011/65/EC.
Magyar:
Ez a berendezés megfelel az alapvető követelményeknek és más vonatkozó irányelveknek
(2006/95/EK, 2011/65/EK).
Türkçe:
Bu cihaz 2006/95/EC, 2011/65/EC direktifleri zorunlu istekler ve diğer hükümlerle ile
uyumludur.
Українська: Обладнання відповідає вимогам і умовам директиви 2006/95/EC, 2011/65/EC.
Slovenčina: Toto zariadenie spĺňa základné požiadavky a ďalšie príslušné ustanovenia smerníc
2006/95/ES, 2011/65/ES.
Deutsch:
Dieses Gerät erfüllt die Voraussetzungen gemäß den Richtlinien 2006/95/EC, 2011/65/EC.
Español:
El presente equipo cumple los requisitos esenciales de la Directiva 2006/95/EC,
2011/65/EC.
Italiano:
Questo apparecchio è conforme ai requisiti essenziali e alle altre disposizioni applicabili
della Direttiva 2006/95/CE, 2011/65/CE.
Nederlands: Dit apparaat voldoet aan de essentiële eisen en andere van toepassing zijnde bepalingen
van richtlijn 2006/95/EC, 2011/65/EC..
Português: Este equipamento cumpre os requesitos essênciais da Directiva 2006/95/EC, 2011/65/EC.
Norsk:
Dette utstyret er i samsvar med de viktigste kravene og andre relevante regler i Direktiv
2006/95/EC, 2011/65/EC.
Svenska:
Denna utrustning är i överensstämmelse med de väsentliga kraven och övriga relevanta
bestämmelser i direktiv 2006/95/EG, 2011/65/EG.
Dansk:
Dette udstyr er i overensstemmelse med de væ sentligste krav og andre relevante
forordninger i direktiv 2006/95/EC, 2011/65/EC.
suomen kieli: Tämä laite täyttää direktiivien 2006/95/EY, 2011/65/EY oleelliset vaatimukset ja muut
asiaankuuluvat määräykset.
----------------------------------------------------------------------------------------------------------------------WEEE Directive & Product Disposal
At the end of its serviceable life, this product should not be treated as household or general waste. It
should be handed over to the applicable collection point for the recycling of electrical and electronic
equipment, or returned to the supplier for disposal.
71
Notice According to GNU General Public License Version 2
This product includes software that is subject to the GNU General Public License version 2. The program is free software and
distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more
than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source
code.
Das Produkt beinhaltet Software, die den Bedingungen der GNU/GPL-Version 2 unterliegt. Das Programm ist eine sog. „Free
Software“, der Autor stellt das Programm ohne irgendeine Gewährleistungen zur Verfügung. Wir bieten Ihnen für einen
Zeitraum von drei Jahren an, eine vollständige maschinenlesbare Kopie des Quelltextes der Programme zur Verfügung zu
stellen – zu nicht höheren Kosten als denen, die durch den physikalischen Kopiervorgang anfallen.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General
Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free
for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other
program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser
General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make
sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive
source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that
you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender
the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you
modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights
that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms
so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for
this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they
have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a
free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have
made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be
distributed under the terms of this General Public License. The ‘“Program’“, below, refers to any such program or work, and a
‘“work based on the Program’“ means either the Program or any derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term ‘“modification’“.) Each licensee is addressed as ‘“you’“.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The
act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a
work based on the Program (independent of having been made by running the Program). Whether that is true depends on
what the Program does.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that
you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep
72
intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the
Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in
exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and
copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these
conditions:
a)
You must cause the modified files to carry prominent notices stating that you changed the files and the date of any
change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the
Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this
License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started
running for such interactive use in the most ordinary way, to print or display an announcement including an
appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty)
and that users may redistribute the program under these conditions, and telling the user how to view a copy of
this License. (Exception: if the Program itself is interactive but does not normally print such an announcement,
your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms,
do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as
part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License,
whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote
it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent
is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the
Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under
the terms of Sections 1 and 2 above provided that you also do one of the following:
a)
Accompany it with the complete corresponding machine-readable source code, which must be distributed under
the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than
your cost of physically performing source distribution, a complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for
software interchange; or,
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This
alternative is allowed only for noncommercial distribution and only if you received the program in object code or
executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work,
complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus
the scripts used to control compilation and installation of the executable. However, as a special exception, the source code
distributed need not include anything that is normally distributed (in either source or binary form) with the major
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component
itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering
equivalent access to copy the source code from the same place counts as distribution of the source code, even though third
parties are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any
attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights
under this License. However, parties who have received copies, or rights, from you under this License will not have their
licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to
modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License.
Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of
this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
73
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license
from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not
impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing
compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent
issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy
simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by
all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License
would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is
intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity
of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system,
which is implemented by public license practices. Many people have made generous contributions to the wide range of
software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to
decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces,
the original copyright holder who places the Program under this License may add an explicit geographical distribution
limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such
case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time.
Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies
to it and ‘“any later version’“, you have the option of following the terms and conditions either of that version or of any later
version published by the Free Software Foundation. If the Program does not specify a version number of this License, you
may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different,
write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the
Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software
generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT
PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE PROGRAM ‘“AS IS’“ WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY
OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
74
75

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : Joey Su
Create Date                     : 2014:02:12 15:17:19+08:00
Modify Date                     : 2014:03:18 09:26:50+08:00
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Joey Su
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2014:03:18 09:26:50+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:6e23f309-9bd0-4b4c-b783-931e003a4d89
Instance ID                     : uuid:3144d27a-28a7-4469-bf56-acb6c8339015
Page Count                      : 75
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NDD9574361310

Navigation menu