Edimax Technology Co 9574791415 802.11ac Dual Band Concurrent Wall-Mount AP User Manual

Edimax Technology Co Ltd 802.11ac Dual Band Concurrent Wall-Mount AP

user manual

Download: Edimax Technology Co 9574791415 802.11ac Dual Band Concurrent Wall-Mount AP User Manual
Mirror Download [FCC.gov]Edimax Technology Co 9574791415 802.11ac Dual Band Concurrent Wall-Mount AP User Manual
Document ID2502797
Application ID3eR0BvAinXy1VHhXeFNp3g==
Document Descriptionuser manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize182.34kB (2279290 bits)
Date Submitted2015-01-16 00:00:00
Date Available2015-01-16 00:00:00
Creation Date2015-01-14 14:32:56
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2015-01-14 14:42:06
Document Titleuser manual
Document CreatorMicrosoft® Office Word 2007
Document Author: Joey Su

AC1200 Wireless LAN 11ac
Dual-Band Concurrent
Wall Mount Access Point
User’s Manual
EW-7679WAUser Manual
05-2014 / v1.0
Version: 1.0
(October, 2014)
CONTENTS
I. Product Information .............................................................................. 1
I-1.
I-2.
I-3.
I-4.
I-5.
I-6.
I-7.
I-8.
Package Contents ........................................................................................................1
System Requirements ..................................................................................................2
Hardware Overview .....................................................................................................2
LED Status ....................................................................................................................3
Reset ............................................................................................................................3
Magnetic Wall Mount ..................................................................................................4
Console ........................................................................................................................5
Safety Information .......................................................................................................6
II. Quick Setup ........................................................................................... 7
II-1.
II-2.
II-3.
Initial Setup ..................................................................................................................7
Basic Settings ...............................................................................................................9
Wi-Fi Protected Setup (WPS) ...................................................................................13
III. Hardware Installation ...........................................................................13
IV. Browser Based Configuration Interface .................................................14
IV-1.
IV-1-1.
IV-1-2.
Information ..............................................................................................................17
System Information .................................................................................................17
Wireless Clients........................................................................................................21
IV-1-3.
IV-1-4.
IV-2.
IV-2-1.
IV-2-2.
IV-2-3.
IV-3.
IV-3-1.
IV-3-1-1.
IV-3-1-2.
IV-3-1-3.
Wireless Monitor .....................................................................................................23
Log ............................................................................................................................24
Network Settings .....................................................................................................26
LAN-Side IP Address .................................................................................................26
LAN Port ...................................................................................................................28
VLAN ........................................................................................................................29
Wireless Settings......................................................................................................30
2.4GHz 11bgn...........................................................................................................30
Basic ...........................................................................................................................31
Advanced ...................................................................................................................34
Security ......................................................................................................................36
IV-3-1-3-1.
IV-3-1-3-2.
IV-3-1-3-3.
IV-3-1-3-4.
IV-3-1-3-5.
IV-3-1-3-6.
IV-3-1-4.
No Authentication ...................................................................................................37
WEP ..........................................................................................................................38
IEEE802.1x/EAP ........................................................................................................38
WPA-PSK ..................................................................................................................38
WPA-EAP ..................................................................................................................39
Additional Authentication .......................................................................................39
WDS ...........................................................................................................................41
IV-3-2.
IV-3-2-1.
IV-3-2-2.
5GHz 11ac 11an .......................................................................................................43
Basic ...........................................................................................................................43
Advanced ...................................................................................................................46
IV-3-2-3.
IV-3-2-4.
IV-3-3.
IV-3-3-1.
IV-3-3-2.
IV-3-3-3.
IV-3-4.
IV-3-5.
IV-4.
IV-4-1.
Security ......................................................................................................................48
WDS ...........................................................................................................................50
RADIUS .......................................................................................................................52
RADIUS Settings .........................................................................................................53
Internal Server ...........................................................................................................54
RADIUS Accounts .......................................................................................................56
MAC Filter ................................................................................................................58
WMM .........................................................................................................................60
Management ...........................................................................................................62
Admin .......................................................................................................................62
IV-4-2.
IV-4-3.
IV-4-4.
IV-5.
IV-5-1.
IV-5-2.
IV-5-3.
IV-5-4.
IV-5-5.
Date and Time ..........................................................................................................65
Syslog Server ............................................................................................................67
I’m Here ...................................................................................................................68
Advanced .................................................................................................................69
LED Settings .............................................................................................................69
Update Firmware .....................................................................................................70
Save/Restore Settings ..............................................................................................72
Factory Default ........................................................................................................75
Reboot .....................................................................................................................76
V. Appendix .............................................................................................77
V-1.
V-1-1.
V-1-2.
V-1-3.
V-1-4.
V-1-5.
V-1-6.
V-2.
V-3.
Configuring your IP address .....................................................................................78
Windows XP .............................................................................................................78
Windows Vista .........................................................................................................80
Windows 7 ...............................................................................................................82
Windows 8 ...............................................................................................................89
Mac ..........................................................................................................................89
Glossary......................................................................................................................91
Hardware Specification............................................................................................94
ENVIRONMENT & PHYSICAL ....................................................................................94
I. Product Information
I-1. Package Contents
1.
2.
3.
Access Point
Antennas x 2
Magnetic Wall Mount x 1
& Screws
4.
5.
6.
Quick Installation Guide
Power Cord
Power Adapter
I-2. System Requirements
- Existing cable/DSL modem & router
- Computer with web browser for access point configuration
I-3. Hardware Overview
A 12V DC IN
C LAN 2
D Reset
B LAN 1 (PoE)
A.
B.
C.
D.
12V DC port to connect the power adapter
LAN port with Power over Ethernet (PoE PD, IN)
LAN port with Power over Ethernet (PoE PSE, OUT)
Reset the access point to factory default settings
I-4. LED Status
LED Status
Description
Off
The access point is off.
Blue
The access point is on.
Amber
The access point is starting up.
I-5. Reset
If you experience problems with your access point, you can reset the device
back to its factory settings. This resets all settings back to default.
1.
Press and hold the reset button on the access point for at least 10 seconds
than release the button.
You may need to use a pin or similar sharp object to push the
reset button.
2.
Wait for the access point to restart. The access point is ready for setup
when the LED is blue.
I-6. Magnetic Wall Mount
The access point includes a magnetic wall mount which requires some
assembly.
1.
Attach the two magnetic wall mount strips to your wall using the included
screws, as shown below.
2.Press the back of your access point firmly against the two wall mounted
magnetic strips, with the access point’s in the correct position, upright
orientation as displayed above.
Ensure your access point is securely attached to the magnetic
strips.
I-7. Console
The access point can be configured via the “Console” port located on the
access point’s side panel using a terminal-emulation program (e.g.
HyperTerminal).
Use the following configuration settings for terminal-emulation programs:
Baud Rate
Data
Parity
Stop
Flow Control
115200
8 bit
None
1 bit
None
I-8. Safety Information
In order to ensure the safe operation of the device and its users, please read
and act in accordance with the following safety instructions.
1. The access point is designed for indoor use only; do not place the access
point outdoors.
2. Do not place the access point in or near hot/humid places, such as a kitchen
or bathroom.
3. Do not pull any connected cable with force; carefully disconnect it from the
access point.
4. Handle the access point with care. Accidental damage will void the
warranty of the access point.
5. The device contains small parts which are a danger to small children under
3 years old. Please keep the access point out of reach of children.
6. Do not place the access point on paper, cloth, or other flammable materials.
The access point may become hot during use.
7. There are no user-serviceable parts inside the access point. If you
experience problems with the access point, please contact your dealer of
purchase and ask for help.
8. The access point is an electrical device and as such, if it becomes wet for
any reason, do not attempt to touch it without switching the power supply
off. Contact an experienced electrical technician for further help.
9. If you smell burning or see smoke coming from the access point or power
adapter, then disconnect the access point and power adapter immediately,
as far as it is safely possible to do so. Call your dealer of purchase for help.
10. Operating temperature when using power adapter is 0°C to 40°C,
Operating temperature when using PoE switch is 0°C to 50°C.
II. Quick Setup
II-1.
Initial Setup
1. Connect the access point to a computer via Ethernet cable.
2. Connect the power adapter to the access point’s 12V DC port and plug the
power adapter into a power supply using the included cable.
3. Please wait a moment for the access point to start up. The access point is
ready when the LED is blue.
4. Set your computer’s IP address to 192.168.2.x where x is a number in the
range 3 – 100. If you are unsure how to do this, please refer to V-1.
Configuring your IP address for more information.
Please ensure there are no other active network connections on
your computer (disconnect Wi-Fi connections and Ethernet
cables).
5. Enter the access point’s default IP address 192.168.2.2 into the URL bar of
a web browser.
6. You will be prompted for a username and password. Enter the default
username “admin” and the default password “1234”.
7. You will arrive the “System Information” screen shown below.
8. Next, please follow the instructions below in II-2. Basic Settings to
configure the access point’s basic settings.
For more advanced configurations, please refer to IV. Browser
Based Configuration Interface.
II-2.
Basic Settings
The instructions below will help you to configure the following basic settings
of the access point:
LAN IP Address
2.4GHz & 5GHz SSID & Security
Administrator Name & Password
Time & Date
It is recommended you configure these settings before using the
access point.
1.
To change the access point’s LAN IP address, go to “Network Settings” >
“LAN-side IP Address” and you will see the screen below.
2.
Enter the IP address settings you wish to use for your access point. You
can use a dynamic (DHCP) or static IP address, depending on your network
environment. Click “Apply” to save the changes and wait a few moments
for the access point to reload.
When you change your access point’s IP address, you need to use
the new IP address to access the browser based configuration
interface instead of the default IP 192.168.2.2.
3.
To change the SSID of your access point’s 2.4GHz wireless network(s), go
to “Wireless Setting” > “2.4GHz 11bgn” > “Basic”. Enter the new SSID for
your 2.4GHz wireless network in the “SSID1” field and click “Apply”.
To utilize multiple 2.4GHz SSIDs, open the drop down menu
labelled “Enable SSID number” and select how many SSIDs you
require. Then enter a new SSID in the corresponding numbered
fields below, before clicking “Apply”.
4.
To configure the security of your access point’s 2.4GHz wireless
network(s), go to “Wireless Setting” > “2.4GHz 11bgn” > “Security”. Select
an “Authentication Method” and enter a “Pre-shared Key” or “Encryption
Key” depending on your choice, then click “Apply”.
If using multiple SSIDs, specify which SSID to configure using the
“SSID” drop down menu.
5.
10
Go to “Wireless Setting” > “5GHz 11ac 11an” and repeat steps 3 & 4 for
the access point’s 5GHz wireless network.
6.
To change the administrator name and password for the browser based
configuration interface, go to “Management” > “Admin”.
7.
Complete the “Administrator Name” and “Administrator Password” fields
and click “Apply”.
8.
To set the correct time for your access point, go to “Management” >
“Date and Time”.
9.
Set the correct time and time zone for your access point using the drop
down menus. The access point also supports NTP (Network Time Protocol)
so alternatively you can enter the host name or IP address of a time server.
Click “Apply” when you are finished.
11
You can use the “Acquire Current Time from your PC” button if
you wish to set the access point to the same time as your PC.
10.
The basic settings of your access point are now configured. Please
refer to III. Hardware Installation for guidance on connecting your access
point to a router or PoE switch.
12
II-3.
III. Hardware Installation
1.
Connect a router or PoE switch to the access point’s LAN 1 port using an
Ethernet cable. PoE switches must be connected to the access point’s LAN
1 port.
2.
If you are using a router, then connect the power adapter to the access
point’s 12V DC port and plug the power adapter into a power supply.
3.
If you are using a PoE (Power over
Ethernet) switch then it is not necessary
to use the included power adapter, the
access point will be powered by the PoE
switch.
Do not use the power adapter if you
are using a PoE switch.
4.
Connect a local network client or switch to the access point’s LAN 2 port
as required.
The access point’s LAN 2 port can support another powered
device(PD).
13
IV. Browser Based Configuration Interface
The browser-based configuration interface enables you to configure the
access point’s advanced features. The EW-7679WAC features a range of
advanced functions such as MAC filtering, MAC RADIUS authentication, VLAN
configurations, up to 32 SSIDs and many more. To access the browser based
configuration interface:
1.
Connect a computer to your access point using an Ethernet cable.
2.
Enter your access point’s IP address in the URL bar of a web browser. The
access point’s default IP address is 192.168.2.2.
3.
You will be prompted for a username and password. The default
username is “admin” and the default password is “1234”, though it was
recommended that you change the password during setup (see II-2. Basic
Settings).
If you cannot remember your password, reset the access point
back to its factory default settings. Refer to I-5. Reset
4.
14
You will arrive at the “System Information” screen shown below.
5.
6.
Use the menu across the top and down the left side to navigate.
Click “Apply” to save changes and reload the access point, or “Cancel” to
cancel changes.
Please wait a few seconds for the access point to reload after you
“Apply” changes, as shown below.
15
7.
16
Please refer to the following chapters for full descriptions of the browser
based configuration interface features.
IV-1.
Information
Screenshots displayed are examples. The information shown on
your screen will vary depending on your configuration.
IV-1-1.
System Information
The “System Information” page displays basic
system information about the access point.
17
System
Model
Product Name
Uptime
Boot From
18
Displays the model number of the access
point.
Displays the product name for reference,
which consists of “AP” plus the MAC address.
Displays the total time since the device was
turned on.
Displays information for the booted
hardware, booted from either USB or internal
Version
MAC Address
Management VLAN
ID
IP Address
Default
Gateway
DNS
DHCP Server
memory.
Displays the firmware version.
Displays the access point’s MAC address.
Displays the management VLAN ID.
Displays the IP address of this device. Click
“Refresh” to update this value.
Displays the IP address of the default
gateway.
IP address of DNS (Domain Name Server)
IP address of DHCP Server.
Wired LAN Port Settings
Wired LAN Port
Specifies which LAN port (1 or 2).
Status
Displays the status of the specified LAN port
(connected or disconnected).
VLAN Mode/ID
Displays the VLAN mode (tagged or untagged)
and VLAN ID for the specified LAN port. See
IV-2-3. VLAN
Wireless 2.4GHz (5GHz)
Status
Displays the status of the 2.4GHz or 5GHz
wireless (enabled or disabled).
MAC Address
Displays the access point’s MAC address.
Channel
Displays the channel number the specified
wireless frequency is using for broadcast.
Transmit Power
Displays the wireless radio transmit power
level as a percentage.
Wireless 2.4GHZ (5GHz) / SSID
SSID
Displays the SSID name(s) for the specified
frequency.
Authentication
Displays the authentication method for the
Method
specified SSID. See IV-3. Wireless Settings
Encryption Type
Displays the encryption type for the specified
SSID. See IV-3. Wireless Settings
VLAN ID
Displays the VLAN ID for the specified SSID.
See IV-2-3. VLAN
19
Additional
Authentication
Wireless Client
Isolation
Displays the additional authentication type for
the specified SSID. See IV-3. Wireless Settings
Displays whether wireless client isolation is in
use for the specified SSID. See IV-2-3. VLAN
Wireless 2.4GHZ (5GHz) / WDS Status
MAC Address
Displays the peer access point’s MAC address.
Encryption Type
Displays the encryption type for the specified
WDS. See IV-3-1-4. WDS
VLAN Mode/ID
Displays the VLAN ID for the specified WDS.
See IV-3-1-4. WDS
Refresh
20
Click to refresh all information.
IV-1-2.
Wireless Clients
The “Wireless Clients” page displays information about all wireless clients
connected to the access point on the 2.4GHz or 5GHz frequency.
Refresh time
Auto Refresh Time
Manual Refresh
Select a time interval for the client table list to
automatically refresh.
Click refresh to manually refresh the client
table.
2.4GHz (5GHz) WLAN Client Table
SSID
Displays the SSID which the client is
connected to.
MAC Address
Displays the MAC address of the client.
Tx
Displays the total data packets transmitted by
the specified client.
Rx
Displays the total data packets received by
the specified client.
21
Signal (%)
Connected Time
Idle Time
Vendor
22
Displays the wireless signal strength for the
specified client.
Displays the total time the wireless client has
been connected to the access point.
Client idle time is the time for which the client
has not transmitted any data packets i.e. is
idle.
The vendor of the client’s wireless adapter is
displayed here.
IV-1-3.
Wireless Monitor
Wireless Monitor is a tool built into the access
point to scan and monitor the surrounding
wireless environment. Select a frequency and click “Scan” to display a list of
all SSIDs within range along with relevant details for each SSID.
Wireless Monitor
Site Survey
Channel Survey
Result
Site Survey Results
Ch
SSID
MAC Address
Security
Signal (%)
Type
Vendor
23
Select which frequency (or both) to scan, and
click “Scan” to begin.
After a scan is complete, click “Export” to save
the results to local storage.
Displays the channel number used by the
specified SSID.
Displays the SSID identified by the scan.
Displays the MAC address of the wireless
router/access point for the specified SSID.
Displays the authentication/encryption type
of the specified SSID.
Displays the current signal strength of the
SSID.
Displays the 802.11 wireless networking
standard(s) of the specified SSID.
Displays the vendor of the wireless
router/access point for the specified SSID.
IV-1-4.
Log
The system log displays system operation information such as up time and
connection processes. This information is useful for network administrators.
When the log is full, old entries are overwritten.
Save
Clear
Refresh
24
Click to save the log as a file on your local
computer.
Clear all log entries.
Refresh the current log.
The following information/events are recorded by the log:
 USB
Mount & unmount
 Wireless Client
Connected & disconnected
Key exchange success & fail
 Authentication
Authentication fail or successful.
 Association
Success or fail
 Change Settings
 System Boot
Displays current model name
 NTP Client
 Wired Link
LAN Port link status and speed status
 Proxy ARP
Proxy ARP module start & stop
 Bridge
Bridge start & stop.
 SNMP
SNMP server start & stop.
 HTTP
HTTP start & stop.
 HTTPS
HTTPS start & stop.
 SSH
SSH-client server start & stop.
 Telnet
Telnet-client server start or stop.
 WLAN (2.4G)
WLAN (2.4G] channel status and country/region status
 WLAN (5G)
WLAN (5G) channel status and country/region status
 ADT
25
IV-2.
Network Settings
Screenshots displayed are examples. The information shown on
your screen will vary depending on your configuration.
IV-2-1.
LAN-Side IP Address
The “LAN-side IP address” page allows you to configure your access point on
your Local Area Network (LAN). You can enable the access point to
dynamically receive an IP address from your router’s DHCP server or you can
specify a static IP address for your access point, as well as configure DNS
servers.
The access point’s default IP address is 192.168.2.2.
LAN-side IP Address
IP Address
Select “DHCP Client” for your access point to
Assignment
be assigned a dynamic IP address from your
router’s DHCP server, or select “Static IP” to
manually specify a static/fixed IP address for
your access point (below).
26
IP Address
Subnet Mask
Default Gateway
Specify the IP address here. This IP address
will be assigned to your access point and will
replace the default IP address.
Specify a subnet mask. The default value is
255.255.255.0
For DHCP users, select “From DHCP” to get
default gateway from your DHCP server or
“User-Defined” to enter a gateway manually.
For static IP users, the default value is blank.
DHCP users can select to get DNS servers’ IP address from DHCP or manually
enter a value. For static IP users, the default value is blank.
DNS Servers
Primary Address
DHCP users can select “From DHCP” to get
primary DNS server’s IP address from DHCP or
“User-Defined” to manually enter a value. For
static IP users, the default value is blank.
Secondary Address Users can manually enter a value when DNS
server’s primary address is set to
“User-Defined”.
27
IV-2-2.
LAN Port
The “LAN Port” page allows you to configure the settings for your access
point’s two wired LAN (Ethernet) ports.
Wired LAN Port Settings
Wired LAN Port
Identifies LAN port 1 or 2.
Enable
Enable/disable specified LAN port.
Speed & Duplex
Select a speed & duplex type for specified LAN
port, or use the “Auto” value. LAN ports can
operate up to 1000Mbps and full-duplex
enables simultaneous data packets
transfer/receive.
Flow Control
Enable/disable flow control. Flow control can
pause new session request until current data
processing is complete, in order to avoid
device overloads under heavy traffic.
802.3az
Enable/disable 802.3az. 802.3az is an Energy
Efficient Ethernet feature which disables
unused interfaces to reduce power usage.
28
IV-2-3.
VLAN
The “VLAN” (Virtual Local Area Network) enables you to configure VLAN
settings. A VLAN is a local area network which maps workstations virtually
instead of physically and allows you to group together or isolate users from
each other. VLAN IDs 1 – 4094 are supported.
VLAN IDs in the range 1 – 4094 are supported.
VLAN Interface
Wired LAN
Port/Wireless
VLAN Mode
VLAN ID
Identifies LAN port 1 or 2 and wireless SSIDs
(2.4GHz or 5GHz).
Select “Tagged Port” or “Untagged Port” for
specified LAN interface.
Set a VLAN ID for specified interface, if
“Untagged Port” is selected.
Management VLAN
VLAN ID
Specify the VLAN ID of the management VLAN.
Only the hosts belonging to the same VLAN can
manage the device.
29
IV-3.
Wireless Settings
Screenshots displayed are examples. The information shown on
your screen will vary depending on your configuration.
IV-3-1.
2.4GHz 11bgn
The “2.4GHz 11bgn” menu allows you to view and configure information for
your access point’s 2.4GHz wireless network across four categories: Basic,
Advanced, Security and WDS.
30
IV-3-1-1. Basic
The “Basic” screen displays basic settings for
your access point’s 2.4GHz Wi-Fi network (s).
31
2.4GHz Basic Settings
Wireless
Enable or disable the access point’s 2.4GHz
wireless radio. When disabled, no 2.4GHz
SSIDs will be active.
Band
Select the wireless standard used for the
access point. Combinations of 802.11b,
802.11g & 802.11n can be selected.
Enable SSID Number Select how many SSIDs to enable for the
2.4GHz frequency from the drop down menu.
A maximum of 16 can be enabled.
SSID#
Enter the SSID name for the specified SSID (up
to 16). The SSID can consist of any
combination of up to 32 alphanumeric
characters.
VLAN ID
Specify a VLAN ID for each SSID.
Auto Channel
Enable/disable auto channel selection. Auto
channel selection will automatically set the
wireless channel for the access point’s 2.4GHz
frequency based on availability and potential
interference. When disabled, select a channel
manually as shown in the next table.
Auto Channel Range Select a range from which the auto channel
setting (above) will choose a channel.
Auto Channel
Specify a frequency for how often the auto
Interval
channel setting will check/reassign the
wireless channel. Check/uncheck the “Change
channel even if clients are connected” box
according to your preference.
Channel Bandwidth Set the channel bandwidth: 20MHz (lower
performance but less interference), 40MHz
(higher performance but potentially higher
interference) or Auto (automatically select
based on interference level).
BSS BasicRateSet
Set a Basic Service Set (BSS) rate: this is a
series of rates to control communication
frames for wireless clients.
32
When auto channel is disabled, select a wireless channel manually:
Channel
Channel Bandwidth
BSS BasicRate Set
33
Select a wireless channel from 1 – 11 (1-13).
Set the channel bandwidth: 20MHz (lower
performance but less interference), 40MHz
(higher performance but potentially higher
interference) or Auto (automatically select
based on interference level).
Set a Basic Service Set (BSS) rate: this is a
series of rates to control communication
frames for wireless clients.
IV-3-1-2. Advanced
These settings are for experienced users only.
Please do not change any of the values on this
page unless you are already familiar with these functions.
Changing these settings can adversely affect the performance of
your access point.
2.4GHz Advanced Settings
Contention Slot
Select “Short” or “Long” – this value is used for
contention windows in WMM (see IV-3-6.
WMM).
Preamble Type
Set the wireless radio preamble type. The
preamble type in 802.11 based wireless
communication defines the length of the CRC
(Cyclic Redundancy Check) block for
communication between the access point and
roaming wireless adapters. The default value is
“Short Preamble”.
Guard Interval
Set the guard interval. A shorter interval can
improve performance.
34
802.11g Protection
Enable/disable 802.11g protection, which
increases reliability but reduces bandwidth
(clients will send Request to Send (RTS) to
access point, and access point will broadcast
Clear to Send (CTS), before a packet is sent
from client.)
802.11n Protection Enable/disable 802.11n protection, which
increases reliability but reduces bandwidth
(clients will send Request to Send (RTS) to
access point, and access point will broadcast
Clear to Send (CTS), before a packet is sent
from client.)
DTIM Period
Set the DTIM (delivery traffic indication
message) period value of the wireless radio.
The default value is 1.
RTS Threshold
Set the RTS threshold of the wireless radio. The
default value is 2347.
Fragment
Set the fragment threshold of the wireless
Threshold
radio. The default value is 2346.
Multicast Rate
Set the transfer rate for multicast packets or
use the “Auto” setting.
Tx Power
Set the power output of the wireless radio. You
may not require 100% output power. Setting a
lower power output can enhance security since
potentially malicious/unknown users in distant
areas will not be able to access your signal.
Beacon Interval
Set the beacon interval of the wireless radio.
The default value is 100.
Station idle
Set the interval for keepalive messages from
timeout
the access point to a wireless client to verify if
the station is still alive/active.
35
IV-3-1-3. Security
The access point provides various security options
(wireless data encryption). When data is
encrypted, information transmitted wirelessly cannot be read by anyone who
does not know the correct encryption key.
It’s essential to configure wireless security in order to prevent
unauthorised access to your network.
Select hard-to-guess passwords which include combinations of
numbers, letters and symbols, and change your password
regularly.
36
2.4GHz Wireless Security Settings
SSID Selection
Select which SSID to configure security settings
for.
Broadcast SSID
Enable or disable SSID broadcast. When
enabled, the SSID will be visible to clients as an
available Wi-Fi network. When disabled, the
SSID will not be visible as an available Wi-Fi
network to clients – clients must manually
enter the SSID in order to connect. A hidden
(disabled) SSID is typically more secure than a
visible (enabled) SSID.
Wireless Client
Enable or disable wireless client isolation.
Isolation
Wireless client isolation prevents clients
connected to the access point from
communicating with each other and improves
security. Typically, this function is useful for
corporate environments or public hot spots
and can prevent brute force attacks on clients’
usernames and passwords.
Load Balancing
Load balancing limits the number of wireless
clients connected to an SSID. Set a load
balancing value (maximum 50).
Authentication
Select an authentication method from the drop
Method
down menu and refer to the information
below appropriate for your method.
Additional
Select an additional authentication method
Authentication
from the drop down menu and refer to the
information below (IV-3-1-3-6.) appropriate for
your method.
IV-3-1-3-1. No Authentication
Authentication is disabled and no password/key is required to connect to the
access point.
Disabling wireless authentication is not recommended. When
disabled, anybody within range can connect to your device’s SSID.
37
IV-3-1-3-2. WEP
WEP (Wired Equivalent Privacy) is a basic encryption type. For a higher
level of security consider using WPA encryption.
Key Length
Select 64-bit or 128-bit. 128-bit is more secure
than 64-bit and is recommended.
Key Type
Choose from “ASCII” (any alphanumerical
character 0-9, a-z and A-Z) or “Hex” (any
characters from 0-9, a-f and A-F).
Default Key
Select which encryption key (1 – 4 below) is
the default key. For security purposes, you
can set up to four keys (below) and change
which is the default key.
Encryption Key 1 – 4 Enter your encryption key/password
according to the format you selected above.
IV-3-1-3-3. IEEE802.1x/EAP
Key Length
Select 64-bit or 128-bit. 128-bit is more secure
than 64-bit and is recommended.
IV-3-1-3-4. WPA-PSK
WPA-PSK is a secure wireless encryption type with strong data
protection and user authentication, utilizing 128-bit encryption keys.
WPA Type
Key Renewal
Interval
Select from WPA/WPA2 Mixed Mode-PSK,
WPA2 or WPA only. WPA2 is safer than WPA
only, but not supported by all wireless clients.
Please make sure your wireless client supports
your selection.
Select “TKIP/AES Mixed Mode” or “AES”
encryption type.
Specify a frequency for key renewal in
minutes.
Pre-Shared Key
Choose from “Passphrase” (8 – 63
Encryption
38
Type
Pre-Shared Key
alphanumeric characters) or “Hex” (up to 64
characters from 0-9, a-f and A-F).
Please enter a security key/password according
to the format you selected above.
IV-3-1-3-5. WPA-EAP
WPA Type
Encryption
Key Renewal
Interval
Select from WPA/WPA2 Mixed Mode-EAP,
WPA2-EAP or WPA-EAP.
Select “TKIP/AES Mixed Mode” or “AES”
encryption type.
Specify a frequency for key renewal in
minutes.
WPA-EAP must be disabled to use MAC-RADIUS authentication.
IV-3-1-3-6. Additional Authentication
Additional wireless authentication methods can also be used:
MAC Address Filter
Restrict wireless clients access based on MAC address specified in the MAC
filter table.
See IV-3-5.MAC Filter to configure MAC filtering.
MAC Filter & MAC-RADIUS Authentication
Restrict wireless clients access using both of the above MAC filtering &
RADIUS authentication methods.
MAC-RADIUS Authentication
Restrict wireless clients access based on MAC address via a RADIUS server, or
password authentication via a RADIUS server.
See IV-3-4.RADIUS to configure RADIUS servers.
WPS must be disabled to use MAC-RADIUS authentication. See
IV-3-3. for WPS settings.
39
MAC RADIUS
Password
40
Select whether to use MAC address or
password authentication via RADIUS server. If
you select “Use the following password”, enter
the password in the field below. The password
should match the “Shared Secret” used in
IV-3-4. RADIUS.
IV-3-1-4. WDS
Wireless Distribution System (WDS) can
bridge/repeat access points together in an
extended network. WDS settings can be configured as shown below.
When using WDS, configure the IP address of each access point to
be in the same subnet and ensure there is only one active DHCP
server among connected access points, preferably on the WAN
side.
WDS must be configured on each access point, using correct MAC addresses.
All access points should use the same wireless channel and encryption
method.
41
2.4GHz
WDS Functionality
Select “WDS with AP” to use WDS with access
point or “WDS Dedicated Mode” to use WDS
and also block communication with regular
wireless clients. When WDS is used, each
access point should be configured with
corresponding MAC addresses, wireless
channel and wireless encryption method.
Local MAC Address Displays the MAC address of your access point.
WDS Peer Settings
WDS #
WDS VLAN
VLAN Mode
VLAN ID
Enter the MAC address for up to four other
WDS devices you wish to connect.
Specify the WDS VLAN mode to “Untagged
Port” or “Tagged Port”.
Specify the WDS VLAN ID when “Untagged
Port” is selected above.
WDS Encryption method
Encryption
Select whether to use “None” or “AES”
encryption and enter a pre-shared key for AES
consisting of 8-63 alphanumeric characters.
42
IV-3-2.
5GHz 11ac 11an
The “5GHz 11ac 11an” menu allows you to view
and configure information for your access point’s
5GHz wireless network across four categories: Basic, Advanced, Security and
WDS.
IV-3-2-1. Basic
The “Basic” screen displays basic settings for
your access point’s 5GHz Wi-Fi network (s).
43
5GHz Basic Settings
Wireless
Enable or disable the access point’s 5GHz
wireless radio. When disabled, no 5GHz SSIDs
will be active.
Band
Select the wireless standard used for the
access point. Combinations of 802.11a,
802.11n & 802.11ac can be selected.
Enable SSID Number Select how many SSIDs to enable for the 5GHz
frequency from the drop down menu. A
maximum of 16 can be enabled.
SSID#
Enter the SSID name for the specified SSID (up
to 16). The SSID can consist of any
combination of up to 32 alphanumeric
characters.
VLAN ID
Specify a VLAN ID for each SSID.
Auto Channel
Enable/disable auto channel selection. Auto
channel selection will automatically set the
wireless channel for the access point’s 5GHz
frequency based on availability and potential
interference. When disabled, select a channel
manually as shown in the next table.
Auto Channel Range Select a range from which the auto channel
setting (above) will choose a channel.
Auto Channel
Specify a frequency for how often the auto
Interval
channel setting will check/reassign the
wireless channel. Check/uncheck the “Change
channel even if clients are connected” box
according to your preference.
Channel Bandwidth Set the channel bandwidth: 20MHz (lower
performance but less interference), Auto
40/20MHz or Auto 80/40/20MHz
(automatically select based on interference
level).
BSS BasicRate Set
Set a Basic Service Set (BSS) rate: this is a
series of rates to control communication
frames for wireless clients.
44
When auto channel is disabled, select a wireless channel manually:
Channel
Channel Bandwidth
BSS BasicRate Set
45
Select a wireless channel.
Set the channel bandwidth: 20MHz (lower
performance but less interference), Auto
40/20MHz or Auto 80/40/20MHz
(automatically select based on interference
level).
Set a Basic Service Set (BSS) rate: this is a
series of rates to control communication
frames for wireless clients.
IV-3-2-2. Advanced
These settings are for experienced users only.
Please do not change any of the values on this
page unless you are already familiar with these functions.
Changing these settings can adversely affect the performance of
your access point.
5GHz Advanced Settings
Guard Interval
Set the guard interval. A shorter interval can
improve performance.
802.11n Protection Enable/disable 802.11n protection, which
increases reliability but reduces bandwidth
(clients will send Request to Send (RTS) to
access point, and access point will broadcast
Clear to Send (CTS), before a packet is sent
from client.)
DTIM Period
Set the DTIM (delivery traffic indication
message) period value of the wireless radio.
The default value is 1.
RTS Threshold
Set the RTS threshold of the wireless radio. The
default value is 2347.
Fragment
Set the fragment threshold of the wireless
Threshold
radio. The default value is 2346.
46
Multicast Rate
Tx Power
Beacon Interval
Station idle
timeout
47
Set the transfer rate for multicast packets or
use the “Auto” setting.
Set the power output of the wireless radio. You
may not require 100% output power. Setting a
lower power output can enhance security since
potentially malicious/unknown users in distant
areas will not be able to access your signal.
Set the beacon interval of the wireless radio.
The default value is 100.
Set the interval for keepalive messages from
the access point to a wireless client to verify if
the station is still alive/active.
IV-3-2-3. Security
The access point provides various security options
(wireless data encryption). When data is
encrypted, information transmitted wirelessly
cannot be read by anyone who does not know the correct encryption key.
It’s essential to configure wireless security in order to prevent
unauthorised access to your network.
Select hard-to-guess passwords which include combinations of
numbers, letters and symbols, and change your password
regularly.
5GHz Wireless Security Settings
SSID Selection
Select which SSID to configure security settings
for.
Broadcast SSID
Enable or disable SSID broadcast. When
enabled, the SSID will be visible to clients as an
available Wi-Fi network. When disabled, the
SSID will not be visible as an available Wi-Fi
network to clients – clients must manually
enter the SSID in order to connect. A hidden
(disabled) SSID is typically more secure than a
visible (enabled) SSID.
48
Wireless Client
Isolation
Load Balancing
Authentication
Method
Additional
Authentication
Enable or disable wireless client isolation.
Wireless client isolation prevents clients
connected to the access point from
communicating with each other and improves
security. Typically, this function is useful for
corporate environments or public hot spots
and can prevent brute force attacks on clients’
usernames and passwords.
Load balancing limits the number of wireless
clients connected to an SSID. Set a load
balancing value (maximum 50).
Select an authentication method from the drop
down menu and refer to the information
below appropriate for your method.
Select an additional authentication method
from the drop down menu and refer to the
information below appropriate for your
method.
Please refer back to IV-3-1-3. Security for more information on authentication
and additional authentication types.
49
IV-3-2-4. WDS
Wireless Distribution System (WDS) can
bridge/repeat access points together in an
extended network. WDS settings can be
configured as shown below.
When using WDS, configure the IP address of each access point to
be in the same subnet and ensure there is only one active DHCP
server among connected access points, preferably on the WAN
side.
WDS must be configured on each access point, using correct MAC addresses.
All access points should use the same wireless channel and encryption
method.
50
5GHz WDS Mode
WDS Functionality
Select “WDS with AP” to use WDS with access
point or “WDS Dedicated Mode” to use WDS
and also block communication with regular
wireless clients. When WDS is used, each
access point should be configured with
corresponding MAC addresses, wireless
channel and wireless encryption method.
Local MAC Address Displays the MAC address of your access point.
WDS Peer Settings
WDS #
WDS VLAN
VLAN Mode
VLAN ID
WDS Encryption
Encryption
51
Enter the MAC address for up to four other
WDA devices you wish to connect.
Specify the WDS VLAN mode to “Untagged
Port” or “Tagged Port”.
Specify the WDS VLAN ID when “Untagged
Port” is selected above.
Select whether to use “None” or “AES”
encryption and enter a pre-shared key for AES
with 8-63 alphanumeric characters.
IV-3-3. RADIUS
The RADIUS sub menu allows you to configure the
access point’s RADIUS server settings, categorized
into three submenus: RADIUS settings, Internal Server and RADIUS accounts.
A RADIUS server provides user-based authentication to improve security and
offer wireless client control – users can be authenticated before gaining
access to a network.
The access point can utilize both a primary and secondary (backup) RADIUS
server for each of its wireless frequencies (2.4GHz & 5GHz). External RADIUS
servers can be used or the access point’s internal RADIUS server can be used.
To use RADIUS servers, go to “Wireless Settings”  “Security” and
select “MAC RADIUS Authentication”  “Additional
Authentication” and select “MAC RADIUS Authentication” (see
IV-3-1-3. & IV-3-2-3).
52
IV-3-4-1. RADIUS Settings
Configure the RADIUS server settings for
2.4GHz & 5GHz. Each frequency can use an
internal or external RADIUS server.
RADIUS Type
RADIUS Server
Authentication
Port
Shared Secret
53
Select “Internal” to use the access point’s
built-in RADIUS server or “external” to use an
external RADIUS server.
Enter the RADIUS server host IP address.
Set the UDP port used in the authentication
protocol of the RADIUS server. Value must be
between 1 – 65535.
Enter a shared secret/password between 1 –
99 characters in length. This should match the
“MAC-RADIUS” password used in IV-3-1-3-6 or
IV-3-2-3.
Session Timeout
Accounting
Accounting Port
Set a duration of session timeout in seconds
between 0 – 86400.
Enable or disable RADIUS accounting.
When accounting is enabled (above), set the
UDP port used in the accounting protocol of
the RADIUS server. Value must be between 1 –
65535.
IV-3-4-2. Internal Server
The access point features a built-in RADIUS
server which can be configured as shown
below used when “Internal” is selected for “RADIUS Type” in the “Wireless
Settings”  “RADIUS”  “RADIUS Settings” menu.
To use RADIUS servers, go to “Wireless Settings”  “Security” and
select “MAC RADIUS Authentication”  “Additional
Authentication” and select “MAC RADIUS Authentication” (see
IV-3-1-3. & IV-3-2-3).
Internal Server
EAP Internal
Authentication
54
Check/uncheck to enable/disable the access
point’s internal RADIUS server.
Select EAP internal authentication type from
the drop down menu.
EAP Certificate File
Format
EAP Certificate File
Displays the EAP certificate file format:
PCK#12(*.pfx/*.p12)
Click “Upload” to open a new window and
select the location of an EAP certificate file to
use. If no certificate file is uploaded, the
internal RADIUS server will use a self-made
certificate.
Shared Secret
Enter a shared secret/password for use
between the internal RADIUS server and
RADIUS client. The shared secret should be 1 –
99 characters in length. This should match the
“MAC-RADIUS” password used in IV-3-1-3-6 or
IV-3-2-3.
Session Timeout
Set a duration of session timeout in seconds
between 0 – 86400.
Termination Action Select a termination-action attribute:
“Reauthentication” sends a RADIUS request to
the access point, “Not-Reathentication” sends
a default termination-action attribute to the
access point, “Not-Send” no
termination-action attribute is sent to the
access point.
55
IV-3-4-3. RADIUS Accounts
The internal RADIUS server can authenticate
up to 256 user accounts. The “RADIUS
Accounts” page allows you to configure and manage users.
56
User Name
Add
Reset
Select
User Name
Password
Customize
Delete Selected
Delete All
Enter the user names here, separated by
commas.
Click “Add” to add the user to the user
registration list.
Clear text from the user name box.
Check the box to select a user.
Displays the user name.
Displays if specified user name has a password
(configured) or not (not configured).
Click “Edit” to open a new field to set/edit a
password for the specified user name (below).
Delete selected user from the user registration
list.
Delete all users from the user registration list.
Edit User Registration List
User Name
Password
57
Existing user name is displayed here and can
be edited according to your preference.
Enter or edit a password for the specified user.
IV-3-5.
MAC Filter
Mac filtering is a security feature that can
help to prevent unauthorized users from
connecting to your access point.
This function allows you to define a list of network devices permitted to
connect to the access point. Devices are each identified by their unique MAC
address. If a device which is not on the list of permitted MAC addresses
attempts to connect to the access point, it will be denied.
To enable MAC filtering, go to “Wireless Settings”  “2.4GHz
11bgn/5GHz 11ac 11an”  “Security”  “Additional
Authentication” and select “MAC Filter” (see IV-3-1-3. & IV-3-2-3).
The MAC address filtering table is displayed below:
58
Add MAC Address
Add
Reset
Enter a MAC address of computer or network
device manually e.g. ‘aa-bb-cc-dd-ee-ff’ or
enter multiple MAC addresses separated with
commas, e.g.
‘aa-bb-cc-dd-ee-ff,aa-bb-cc-dd-ee-gg’
Click “Add” to add the MAC address to the
MAC address filtering table.
Clear all fields.
MAC address entries will be listed in the “MAC Address Filtering Table”. Select
an entry using the “Select” checkbox.
Select
MAC Address
Delete Selected
Delete All
Export
59
Delete selected or all entries from the table.
The MAC address is listed here.
Delete the selected MAC address from the
list.
Delete all entries from the MAC address
filtering table.
Click “Export” to save a copy of the MAC
filtering table. A new window will pop up for
you to select a location to save the file.
IV-3-6. WMM
Wi-Fi Multimedia (WMM) is a Wi-Fi Alliance
interoperability certification based on the
IEEE 802.11e standard, which provides
Quality of Service (QoS) features to IEE 802.11 networks. WMM prioritizes
traffic according to four categories: background, best effort, video and voice.
Configuring WMM consists of adjusting parameters on queues for different
categories of wireless traffic. Traffic is sent to the following queues:
Background
Best Effort
Video
Voice
Low
Priority
Medium
Priority
High
Priority
High
Priority
High throughput, non time sensitive bulk
data e.g. FTP
Traditional IP data, medium throughput and
delay.
Time sensitive video data with minimum
time delay.
Time sensitive data such as VoIP and
streaming media with minimum time delay.
Queues automatically provide minimum transmission delays for video, voice,
multimedia and critical applications. The values can further be adjusted
manually:
60
CWMin
CWMax
AIFSN
TxOP
61
Minimum Contention Window (milliseconds):
This value is input to the initial random
backoff wait time algorithm for retry of a data
frame transmission. The backoff wait time will
be generated between 0 and this value. If the
frame is not sent, the random backoff value is
doubled until the value reaches the number
defined by CWMax (below). The CWMin value
must be lower than the CWMax value. The
contention window scheme helps to avoid
frame collisions and determine priority of
frame transmission. A shorter window has a
higher probability (priority) of transmission.
Maximum Contention Window (milliseconds):
This value is the upper limit to random
backoff value doubling (see above).
Arbitration Inter-Frame Space (milliseconds):
Specifies additional time between when a
channel goes idle and the AP/client sends
data frames. Traffic with a lower AIFSN value
has a higher priority.
Transmission Opportunity (milliseconds): The
maximum interval of time an AP/client can
transmit. This makes channel access more
efficiently prioritized. A value of 0 means only
one frame per transmission. A greater value
effects higher priority.
IV-4.
Management
Screenshots displayed are examples. The information shown on
your screen will vary depending on your configuration.
IV-4-1.
Admin
You can change the password used to login to
the browser-based configuration interface here.
It is advised to do so for security purposes.
If you change the administrator password, please make a note
of the new password. In the event that you forget this
password and are unable to login to the browser based
configuration interface, see I-5. Reset for how to reset the
access point.
62
Account to Manage This Device
Administrator
Set the access point’s administrator name.
Name
This is used to log in to the browser based
configuration interface and must be between
4-16 alphanumeric characters (case sensitive).
Administrator
Set the access point’s administrator password.
Password
This is used to log in to the browser based
configuration interface and must be between
4-32 alphanumeric characters (case sensitive).
Advanced Settings
Product Name
63
Edit the product name according to your
preference consisting of 1-32 alphanumeric
characters. This name is used for reference
purposes.
Management
Protocol
SNMP Version
SNMP Get
Community
SNMP Set
Community
SNMP Trap
SNMP Trap
Community
SNMP Trap
Manager
Check/uncheck the boxes to enable/disable
specified management interfaces (see below).
When SNMP is enabled, complete the SNMP
fields below.
Select SNMP version appropriate for your
SNMP manager.
Enter an SNMP Get Community name for
verification with the SNMP manager for
SNMP-GET requests.
Enter an SNMP Set Community name for
verification with the SNMP manager for
SNMP-SET requests.
Enable or disable SNMP Trap to notify SNMP
manager of network errors.
Enter an SNMP Trap Community name for
verification with the SNMP manager for
SNMP-TRAP requests.
Specify the IP address or sever name (2-128
alphanumeric characters) of the SNMP
manager.
HTTP
Internet browser HTTP protocol management interface
HTTPS
Internet browser HTTPS protocol management interface
TELNET
Client terminal with telnet protocol management interface
SSH
Client terminal with SSH protocol version 1 or 2 management interface
SNMP
Simple Network Management Protocol. SNMPv1, v2 & v3 protocol supported.
SNMPv2 can be used with community based authentication. SNMPv3 uses
user-based security model (USM) architecture.
64
IV-4-2.
Date and Time
You can configure the time zone settings of your
access point here. The date and time of the
device can be configured manually or can be synchronized with a time server.
Date and Time Settings
Local Time
Set the access point’s date and time manually
using the drop down menus.
Acquire Current
Click “Acquire Current Time from Your PC” to
Time from your PC enter the required values automatically
according to your computer’s current time and
date.
65
NTP Time Server
Use NTP
Server Name
Update Interval
Time Zone
Time Zone
66
The access point also supports NTP (Network
Time Protocol) for automatic time and date
setup.
Enter the host name or IP address of the time
server if you wish.
Specify a frequency (in hours) for the access
point to update/synchronize with the NTP
server.
Select the time zone of your country/ region. If
your country/region is not listed, please select
another country/region whose time zone is the
same as yours.
IV-4-3.
Syslog Server
The system log can be sent to a server or
to attached USB storage.
Syslog Server
Transfer Logs
Check/uncheck the box to enable/disable the
use of a syslog server, and enter a host
name, domain or IP address for the server,
consisting of up to 128 alphanumeric
characters.
Copy Logs to
Check/uncheck the box to enable/disable
Attached USB Device copying logs to attached USB storage.
67
IV-4-4.
I’m Here
The access point features a built-in buzzer
which can sound on command using the “I’m
Here” page. This is useful for network administrators and engineers working
in complex network environments to locate the access point.
The buzzer is loud!
Duration of Sound
Sound Buzzer
68
Set the duration for which the buzzer will
sound when the “Sound Buzzer” button is
clicked.
Activate the buzzer sound for the above
specified duration of time.
IV-5.
Advanced
Screenshots displayed are examples. The information shown on
your screen will vary depending on your configuration.
IV-5-1.
LED Settings
The access point’s LEDs can be manually
enabled or disabled according to your
preference.
Power LED
Diag LED
69
Select on or off.
Select on or off.
IV-5-2.
Update Firmware
The “Firmware” page allows you to update
the system firmware to a more recent
version. Updated firmware versions often
offer increased performance and security, as well as bug fixes. You can
download the latest firmware from the website.
Do not switch off or disconnect the access point during a firmware
upgrade, as this could damage the device.
70
Update Firmware
From
Select to upload firmware from your local
computer or from an attached USB device.
(You must transfer a firmware file to the USB
device first.)
Firmware Update File Click “Browse” to open a new window to
locate and select the firmware file in your
computer.
Update
Click “Update” to upload the specified
firmware file to your access point.
71
IV-5-3.
Save/Restore Settings
The access point’s “Save/Restore Settings”
page enables you to save/backup the access
point’s current settings as a file to your local computer or a USB device
attached to the access point, and restore the access point to previously saved
settings.
72
Save / Restore Settings
Using Device
Select to save the access point’s settings to
your local computer or to an attached USB
device.
Save Settings to USB
Save Settings
Click “Save” to save settings and a new
window will open to specify a location to
save the settings file. If saving settings to
your computer or USB device, you can also
check the “Encrypt the configuration file with
a password” box and enter a password to
protect the file in the field underneath, if you
wish.
Restore Settings from USB
Restore Settings
Click the browse button to find a previously
saved settings file on your computer or
select a settings file from your USB device.
73
Settings files located on your USB storage
will automatically be displayed. Then click
“Restore” to replace your current settings. If
your settings file is encrypted with a
password, check the “Open file with
password” box and enter the password in
the field underneath.
74
IV-5-4.
Factory Default
If the access point malfunctions or is not
responding, then it is recommended that you
reboot the device (see IV-5.5) or reset the device back to its factory default
settings. You can reset the access point back to its default settings using this
feature if the location of the access point is not convenient to access the reset
button.
Factory Default
Click “Factory Default” to restore settings to
the factory default. A pop-up window will
appear and ask you to confirm.
After resetting to factory defaults, please wait for the access
point to reset and restart.
75
IV-5-5.
Reboot
If the access point malfunctions or is not
responding, then it is recommended that
you reboot the device or reset the access point back to its factory default
settings (see IV-5-4). You can reboot the access point remotely using this
feature.
Reboot
76
Click “Reboot” to reboot the device. A
countdown will indicate the progress of the
reboot.
V. Appendix
V-1.
Configuring your IP address
The access point uses the default IP address 192.168.2.2. In order to access
the browser based configuration interface, you need to modify the IP address
of your computer to be in the same IP address subnet e.g. 192.168.2.x (x = 3 –
254).
The procedure for modifying your IP address varies across different operating
systems; please follow the guide appropriate for your operating system.
In the following examples we use the IP address 192.168.2.10 though you can
use any IP address in the range 192.168.2.x (x = 3 – 254).
77
V-1-1.
1.
2.
Windows XP
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”. Double-click the “Network and
Internet Connections” icon, click “Network Connections”, and then
double-click “Local Area Connection”. The “Local Area Connection Status”
window will then appear, click “Properties”.
Select “Use the following IP address”, then input the following values:
IP address: 192.168.2.10
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
78
79
V-1-2.
1.
2.
Windows Vista
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”. Click “View Network Status and
Tasks”, then click “Manage Network Connections”. Right-click “Local Area
Network”, then select “Properties”. The “Local Area Connection Properties”
window will then appear, select “Internet Protocol Version 4 (TCP / IPv4)”,
and then click “Properties”.
Select “Use the following IP address”, then input the following values:
IP address: 192.168.2.10
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
80
81
V-1-3.
Windows 7
1.
Click the “Start” button (it should be located in the lower-left corner of
your computer), then click “Control Panel”.
2.
Under “Network and Internet” click “View network status and tasks”.
3.
Click “Local Area Connection”.
82
4.
83
Click “Properties”.
5.Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
6.
Select “Use the following IP address”, then input the following values:
IP address: 192.168.2.10
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
84
V-1-4.
Windows 8
1.
From the Windows 8 Start screen, you need to switch to desktop mode.
Move your curser to the bottom left of the screen and click.
2.
In desktop mode, click the File Explorer icon in the bottom left of the
screen, as shown below.
85
3.
86
Right click “Network” and then select “Properties”.
4.
5.
87
In the window that opens, select “Change adapter settings” from the left
side.
Choose your connection and right click, then select “Properties”.
6.
Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
7.
Select “Use the following IP address”, then input the following values:
IP address: 192.168.2.10
Subnet Mask: 255.255.255.0
Click ‘OK’ when finished.
88
V-1-5.
1.
Mac
Have your Macintosh computer operate as usual, and click on “System
Preferences”
2.
In System Preferences, click on “Network”.
3.
Click on “Ethernet” in the left panel.
4.
89
Open the drop-down menu labeled “Configure IPv4” and select
“Manually”.
5.
90
Enter the IP address 192.168.2.10 and subnet mask 255.255.255.0. Click
on “Apply” to save the changes.
V-1-6. Glossary
Default Gateway (Access point): Every non-access point IP device needs to
configure a default gateway’s IP address. When the device sends out an IP
packet, if the destination is not on the same network, the device has to send
the packet to its default gateway, which will then send it out towards the
destination.
DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives
every computer on your home network an IP address.
DNS Server IP Address: DNS stands for Domain Name System, which allows
Internet servers to have a domain name (such as www.Broadbandaccess
point.com) and one or more IP addresses (such as 192.34.45.8). A DNS server
keeps a database of Internet servers and their respective domain names and
IP addresses, so that when a domain name is requested (as in typing
"Broadbandaccess point.com" into your Internet browser), the user is sent to
the proper IP address. The DNS server IP address used by the computers on
your home network is the location of the DNS server your ISP has assigned to
you.
DSL Modem: DSL stands for Digital Subscriber Line. A DSL modem uses your
existing phone lines to transmit data at high speeds.
Ethernet: A standard for computer networks. Ethernet networks are
connected by special cables and hubs, and move data around at up to 10/100
million bits per second (Mbps).
IP Address and Network (Subnet) Mask: IP stands for Internet Protocol. An IP
address consists of a series of four numbers separated by periods, that
identifies a single, unique Internet computer host in an IP network. Example:
192.168.2.1. It consists of 2 portions: the IP network address, and the host
identifier.
The IP address is a 32-bit binary pattern, which can be represented as four
cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each
“aaa” can be anything from 000 to 255, or as four cascaded binary numbers
separated by “.”: bbbbbbbb.bbbbbbbb.bbbbbbbb.bbbbbbbb, where each “b”
can either be 0 or 1.
91
A network mask is also a 32-bit binary pattern, and consists of consecutive
leading 1’s followed by consecutive trailing 0’s, such as
11111111.11111111.11111111.00000000. Therefore sometimes a network
mask can also be described simply as “x” number of leading 1’s.
When both are represented side by side in their binary forms, all bits in the IP
address that correspond to 1’s in the network mask become part of the IP
network address, and the remaining bits correspond to the host ID.
For example, if the IP address for a device is, in its binary form,
11011001.10110000.10010000.00000111, and if its network mask is,
11111111.11111111.11110000.00000000
It means the device’s network address is
11011001.10110000.10010000.00000000, and its host ID is,
00000000.00000000.00000000.00000111. This is a convenient and efficient
method for access points to route IP packets to their destination.
ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an
IP address for the Internet access point located at the ISP's office.
ISP: Internet Service Provider. An ISP is a business that provides connectivity
to the Internet for individuals and other businesses or organizations.
LAN: Local Area Network. A LAN is a group of computers and devices
connected together in a relatively small area (such as a house or an office).
Your home network is considered a LAN.
MAC Address: MAC stands for Media Access Control. A MAC address is the
hardware address of a device connected to a network. The MAC address is a
unique identifier for a device with an Ethernet interface. It is comprised of
two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique
for each manufacturer), plus 3 bytes that are often used as the product’s
serial number.
Access point: An access point is an intelligent network device that forwards
packets between different networks based on network layer address
information such as IP addresses.
Subnet Mask: A subnet mask, which may be a part of the TCP/IP information
provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configured
like an IP address. It is used to create IP address numbers used only within a
92
particular network (as opposed to valid IP address numbers recognized by the
Internet, which must be assigned by InterNIC).
TCP/IP, UDP: Transmission Control Protocol/Internet Protocol (TCP/IP) and
Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data
transmission over the Internet. Both TCP and UDP are transport layer protocol.
TCP performs proper error detection and error recovery, and thus is reliable.
UDP on the other hand is not reliable. They both run on top of the IP (Internet
Protocol), a network layer protocol.
Web-based management Graphical User Interface (GUI): Many devices
support a graphical user interface that is based on the web browser. This
means the user can use the familiar Netscape or Microsoft Internet Explorer
to Control/configure or monitor the device being managed.
93
V-2.
Hardware Specification
V-3.
ENVIRONMENT & PHYSICAL
94
COPYRIGHT
Copyright © 2014 by this company. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this company
This company makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular
purpose. Any software described in this manual is sold or licensed "as is". Should the programs prove
defective following their purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents thereof without obligation to notify
any person of such revision or changes.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Any changes or modifications not expressly
approved by the party responsible for compliance could void the authority to operate equipment.
This device is restricted to indoor use only.
Federal Communications Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN PARLIAMENT AND
THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal equipment and the mutual
recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to
ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Bulgaria, Cyprus, Czech,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Turkey, and United Kingdom. The ETSI
version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein, Norway, and
Switzerland.
EU Countries Not Intended for Use
None

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : Yes
Author                          : Joey Su
Create Date                     : 2015:01:14 14:32:56+08:00
Modify Date                     : 2015:01:14 14:42:06+08:00
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Format                          : application/pdf
Creator                         : Joey Su
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2015:01:14 14:42:06+08:00
Producer                        : Microsoft® Office Word 2007
Document ID                     : uuid:7541d1fa-abfa-43fe-84c0-86e0bbb17957
Instance ID                     : uuid:500e087f-772e-430b-960f-c842acb985e0
Page Count                      : 99
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NDD9574791415

Navigation menu