EK 600U,601W RS 232 Commands
Ek-600U,601W-Rs-232-Commands EK-600U,601W-RS-232-Commands EK-600U,601W-RS-232-Commands 59438f56494b384a42b9c7aa product sslcd 3:
2018-05-23
: Eiki Ek-600U,601W-Rs-232-Commands EK-600U,601W-RS-232-Commands 59438d99494b384a42b9c7a9 product
Open the PDF directly: View PDF 
.
Page Count: 6
RS232C Command List for EK-600U/601W
Pin Alignment
RS232C Setting
Standard format
commands commands parameter(%1=)
CR_IMAGE 0~7 Check Display Mode
CF_IMAGE_%1 0 Presentation
1 Bright
2 Movie
3 sRGB
4 Blackboard
5 3D_DLP
6 DICOM SIM
7 User
CR_BRIGHT -50~50 Check Brightness Value
-50~50 Set Brightness Value (-50 ~ 50)
C20 UP Increase setting value (+1) from current setting
C21 DN Decrease setting value (-1) from current setting
CR_CONT -50~50 Check Contrast Value
-50~50 Set Contrast Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_SHARP 1~15 Check Sharpness Value
1~15 Set Sharpness Value (1 ~ 15)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_COLOR -50~50 Check Color Value
-50~50 Set Color Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_TINT -50~50 Check Tint Value
-50~50 Set Tint Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_NZRED 0~10 Check Noise Reduction Value
0~10 Set Noise Reduction Value (0 ~ 10)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_BCOLOR 1~10 Check Brilliant Color Value
1~10 Set Brilliant Color Value (1 ~ 10)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_DYNAMICBLACK 0 ~ 1 Check Dynamic Black setting
0 off
1on
CR_GAMMA 0 ~ 7 Check Gamma setting
0 Film
1 Graphics
2 1.8
3 2
4 2.2
5 2.6
6 Blackboard
7 DICOM
CR_COLTEMP 0~3 Check Color Temp setting
0 Warm
1 Standard
2 Cool
3 Cold
CR_COLORSPACE 0~3 Check Color Space setting
0 digital:Auto analog:AUTO
1 digital:RGB0~255 analog:RGB
2 digital:RGB16~235 analog:YUV
3 digital:YUV
CR_GAIN_R -50~50 Check Red Gain Value
-50~50 Set Red Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_GAIN_G -50~50 Check Green Gain Value
-50~50 Set Red Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_GAIN_B -50~50 Check Blue Gain Value
-50~50 Set Red Gain Value(-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_OFFSET_R -50~50 Check Red Bias Value
-50~50 Set Red Bias Value(-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_OFFSET_G -50~50 Check Green Bias Value
-50~50 Set Green Bias Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_OFFSET_B -50~50 Check Blue Bias Value
-50~50 Set Blue Bias Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
1-13-7 CF_GO_RST Reset the value of Gain/Bias
CR_CM_RH -50~50 Check Red Part of Hue Value
-50~50 Set Red Part of Hue Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_RS -50~50 Check Red Part of Saturation Value
-50~50 Set Red Part of Saturation Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_RG -50~50 Check Red Part of Gain Value
-50~50 Set Red Part of Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_GH -50~50 Check Green Part of Hue Value
-50~50 Set Green Part of Hue Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_GS -50~50 Check Green Part of Saturation Value
-50~50 Set Green Part of Saturation Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
1-13-6
1-14-1
1-14-2
1-14-3
1-14-4
1-14-5
1-9
1-10
1-11
1-12
1-13-1
1-13-2
1-13-3
1-13-4
1-13-5
Item
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
Expand format
CF_CM_RS_%1
CF_CM_RG_%1
CF_CM_GH_%1
CF_CM_GS_%1
CF_BRIGHT_%1
CF_CONT_%1
CF_SHARP_%1
CF_COLOR_%1
CF_TINT_%1
CF_NZRED_%1
CF_BCOLOR_%1
CF_DYNAMICBLACK_%1
CF_GAMMA_%1
CF_COLTEMP_%1
CF_GAIN_R_%1
CF_GAIN_G_%1
CF_GAIN_B_%1
CF_COLORSPACE_%1
CF_OFFSET_R_%1
CF_OFFSET_G_%1
CF_OFFSET_B_%1
CF_CM_RH_%1
note
IMAGE
Category
reply
Standard format
commands commands parameter(%1=)
Item
Expand format
note
Category
reply
CR_CM_GG -50~50 Check Green Part of Gain Value
-50~50 Set Green Part of Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_BH -50~50 Check Blue Part of Hue Value
-50~50 Set Blue Part of Hue Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_BS -50~50 Check Blue Part of Saturation Value
-50~50 Set Blue Part of Saturation Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_BG -50~50 Check Blue Part of Gain Value
-50~50 Set Blue Part of Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_CH -50~50 Check Cyan Part of Hue Value
-50~50 Set Cyan Part of Hue Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_CS -50~50 Check Cyan Part of Saturation Value
-50~50 Set Cyan Part of Saturation Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_CG -50~50 Check Cyan Part of Gain Value
-50~50 Set Cyan Part of Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_MH -50~50 Check Magenta Part of Hue Value
-50~50 Set Magenta Part of Hue Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_MS -50~50 Check Magenta Part of Saturation Value
-50~50 Set Magenta Part of Saturation Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_MG -50~50 Check Magenta Part of Gain Value
-50~50 Set Magenta Part of Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_YH -50~50 Check Yellow Part of Hue Value
-50~50 Set Yellow Part of Hue Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_YS -50~50 Check Yellow Part of Saturation Value
-50~50 Set Yellow Part of Saturation Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_YG -50~50 Check Yellow Part of Gain Value
-50~50 Set Yellow Part of Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_WGR -50~50 Check White Part of Red Gain Value
-50~50 Set White Part of Red Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_WGG -50~50 Check White Part of Green Gain Value
-50~50 Set White Part of Green Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_CM_WGB -50~50 Check White Part of Blue Gain Value
-50~50 Set White Part of Blue Gain Value (-50 ~ 50)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
1-14-22 CF_CMFDEFAULT_RST Reset the value of Color Matching
CR_AUTOPHASEFREQ 0~1 Check Auto Phace and frequency Value. 0:off,1:on
0 Set Auto Phace and frequency Value
1 Set Auto Phace and frequency Value
CR_PHASE 0~31 Check Phase Value
0~31 Set Phase Value (0 ~ 31)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_FREQ -10~10 Check Frequency Value
-10~10 Set Frequenc Value (-10 ~ 10)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_HPOS -10~10 Check Horizontal Position Value
-10~10 Set Horizontal Position Value (-10 ~ 10)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_VPOS -10~10 Check Vertical Position Value
-10~10 Set Vertical Position Value (-10 ~ 10)
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_VBLEVEL -5~5 Check Video Black Level setting
-5~5 Set Video Black Level setting
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_VWLEVEL 0~31 Check White Peaking Value
0~31 Set White Peaking setting
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_IRE Check IRE Value
0 0
1 7.5
1-23 CF_IMAGE_RESET Reset the value of all image setting
CR_ASPECT 1~7 CheckAspect Ratio setting
1 4:3
2 16:9
3 16:10
4 N/A
5 LBX
6 Native
7 Auto
1-19
1-20
1-21
1-22
2-1
1-14-18
1-14-19
1-14-20
1-14-21
1-15
1-16
1-17
1-18
1-14-9
1-14-10
1-14-11
1-14-12
1-14-13
1-14-14
1-14-15
1-14-16
1-14-17
1-14-6
1-14-7
1-14-8
CF_CM_CH_%1
CF_CM_CS_%1
CF_CM_CG_%1
CF_CM_GG_%1
CF_CM_BH_%1
CF_CM_BS_%1
CF_CM_BG_%1
CF_CM_MH_%1
CF_CM_MS_%1
CF_CM_MG_%1
CF_CM_YH_%1
CF_CM_YS_%1
CF_VBLEVEL_%1
CF_PHASE_%1
CF_FREQ_%1
CF_HPOS_%1
CF_VPOS_%1
CF_CM_YG_%1
CF_CM_WGR_%1
CF_AUTOPHASEFREQ_%1
CF_CM_WGG_%1
CF_CM_WGB_%1
CF_ASPECT_%1
CF_VWLEVEL_%1
CF_IRE_%1
DISPLAY
IMAGE
Standard format
commands commands parameter(%1=)
Item
Expand format
note
Category
reply
CR_ZOOM -5~25 Check Zoom value
-5~25 Set Zoom value
C30 UP Increase setting value (+1) from current setting
C31 DN Decrease setting value (-1) from current setting
CR_EDGEMASK 0~10 Check Edge Mask value
0~10 Set Edge Mask value
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_DSHIFT_H -100~100 Check H Digital Shift value
'-100~100 Set H Digital Shift value
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_DSHIFT_V -100~100 Check V Digital Shift value
'-100~100 Set V Digital Shift value
UP Increase setting value (+1) from current setting
DN Decrease setting value (-1) from current setting
CR_KYSTN_H -30 ~ 30 Check H Keystone value
-30 ~ 30 Set H Keystone Value ('-30 ~ 30)
C90 UP Increase setting value (+1) from current setting
C91 DN Decrease setting value (-1) from current setting
CR_KYSTN_V -30 ~ 30 Check V Keystone value
-30 ~ 30 Set V Keystone Value ('-30 ~ 30)
C8E UP Increase setting value (+1) from current setting
C8F DN Decrease setting value (-1) from current setting
CR_AUTOKYSTN_V 0~1 Check V Auto Keystone value
0 Set V Auto Keystone value
1 Set V Auto Keystone value
CR_3D-MODE 0~2 0:off, 1:DLP-Link, 2:VESA-3D
0 off
1 DLP-Link
2 VESA-3D
CR_3D-2D 0~2 0:3D, 1:L(2D), 2:R(2D)
03D
1 L
2 R
CR_3D-INVERT 0~1 Check 3D-Invert setting
0 off
1on
CR_LANG 0~22 Check Language setting
0 English
1 Deutsch
2يبرع
4 Français
5 Italiano
6 Español
7 Português
8 Polski
9 Nederlands
10 Русский
11 Suomi
12 Svenska
13 (Norsk/Dansk)
14 Magyar
15 Čeština
16
繁體中文
17
簡体中文
18
日本語
19
한국어
20
ไทย
21 Türkçe
22 Indonesian
CR_PROJECTION 0~3 Check Projection (Ceiling/Rear) setting
0 desk top
1 ceiling
2 real
3 real and ceiling
CR_SCREENTYPE 0~1 Check screen type setting
0 16:10
1 16:9
CR_MENULACTION 0~4
0 Top Left
1 Top Right
2 Center
3 bottom Left
4 bottom Right
CR_PROJECTORID 0~99 Check Projector ID
CF_PROJECTORID_%1 0~99 Set Projector ID
CR_INTERSPEKER 0~1 Check Internal speaker status
0 off
1on
CR_MUTE 0~1 Check Mute status
0 off
1on
CR_VOLUMEAUDIO 0~10 Check Audio Volume setting
CF_VOLUMEAUDIO_%1 0~10 Set Audio Volume setting
CR_VOLUMEMIC 0~10 Check Mic Volume setting
CF_VOLUMEMIC_%1 0~10 Set Mic Volume setting
CR_AUDIOIN 0~3 Check Audio Input setting
0 default
1 Audio input 1
2 Audio input 2
3 Audio input 3
CR_AUDIOOUTSTANDBY 0~1 Check Audio Out Standby setting
0 off
1on
CR_LOGO 0~2 Check LOGO setting
CF_LOGO_%1 0 Default
1 User(Logo capturu only)
2 Neutral
3-12 CF_LOGOCAPTURE Logo Capture
CR_CCAPTIONDISP 0~2 Check Closed Caption setting
0 off
1CC1
2CC2
3-13
3-4
3-5
3-6
3-7
3-8-1
3-8-2
3-9
3-10
3-11
2-6
2-7
2-8
2-9
2-10
2-11
3-1
3-2
3-3
2-2
2-3
2-4
2-5
CF_ZOOM_%1
CF_EDGEMASK_%1
CF_CCAPTIONDISP_%1
CF_INTERSPEKER_%1
CF_MUTE_%1
CF_AUDIOIN_%1
CF_AUDIOOUTSTANDBY_%1
CF_3D-MODE_%1
CF_3D-2D_%1
CF_3D-INVERT_%1
CF_LANG_%1
CF_DSHIFT_H_%1
CF_DSHIFT_V_%1
CF_KYSTN_H_%1
CF_KYSTN_V_%1
CF_AUTOKYSTN_V_%1
SETUP
DISPLAY
CF_PROJECTION_%1
CF_SCREENTYPE_%1
CF_MENULACTION_%1
Standard format
commands commands parameter(%1=)
Item
Expand format
note
Category
reply
CR_HDBASETNET 0~1 Check HDBaseT Ethernet setting
0 off
1on
CR_HDBASET232 0~1 Check HDBaseT RS232 setting
0 off
1on
CR_CRESTRON 0~1 Check Crestron setting
0 off
1on
CR_EXTRON 0~1 Check Extron setting
0 off
1on
CR_PJLINK 0~1 Check PJ-Link setting
0 off
1on
CR_AMX 0~1 Check AMX Device Discovery setting
0 off
1on
CR_TELNET 0~1 Check Telnet setting
0 off
1on
CR_HTTP 0~1 Check HTTP setting
0 off
1on
CR_SOURCEVGA1 0~1 Check Input source VGA1 setting
0 disable
1enable
CR_SOURCEVGA2 0~1 Check Input source VGA2 setting
0 disable
1enable
CR_SOURCEHDMI1 0~1 Check Input source HDMI1 setting
0 disable
1enable
CR_SOURCEHDMI2 0~1 Check Input source HDMI2 setting
0 disable
1enable
CR_SOURCEVIDEO 0~1 Check Input source VIDEO setting
0 disable
1enable
CR_SOURCESVIDEO 0~1 Check Input source SVIDEO setting
0 disable
1enable
CR_SOURCEDP 0~1 Check Input source Displayport setting
0 disable
1enable
CR_SOURCEHDBASET 0~1 Check Input source HDBaseT setting
0 disable
1enable
CR_SOURCELOCK 0~1 Check Input Source Lock setting
0 off
1on
CR_ALTITUDE 0~1 Check High Altitude setting
0 off
1on
CR_INFOHIDE 0~1 Check Information Hide setting
0 off
1on
CR_KEYPADLOCK 0~1 Check Keypad Lock setting
0 off
1on
CR_DISPLAYMODELOCK 0~1 Check Display Mode Lock setting
0 off
1on
CR_TESTPAT 0~2 Check Test Pattern setting
0 None
1 Grid
2 White
CR_BACKGND 0~4 Check Background color setting
0 Black
1 Red
2 Blue
3 Green
4 White
CR_WALL 0~5 Check Wall color setting
0 off
1 Light Yellow
2 Light Green
3 Light Blue
4 Pink
5 Gray
CR_REMOTEUSER1 0~7 Check Remote USER key 1 setting
0 HDMI2
1DP
2 VGA2
3 SVEDIO
4 Test Pattrn
5 Zoom
6 Info
7 HDBeseT
CR_REMOTEUSER2 0~7 Check Remote USER key 2 setting
0 HDMI2
1DP
2 VGA2
3 SVEDIO
4 Test Pattrn
5 Zoom
6 Info
7 HDBeseT
CR_IR 0~3 Check IR Function setting
0all
1 front
2 top
3 off
4-12
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-1-1
4-1-2
4-1-3
4-1-4
4-1-5
4-1-6
4-1-7
4-1-8
4-2
3-14-1
3-14-2
3-14-3
3-14-4
3-14-5
3-14-6
3-14-7
3-14-8
CF_HDBASETNET_%1
CF_HDBASET232_%1
CF_CRESTRON_%1
CF_TELNET_%1
CF_WALL_%1
CF_REMOTEUSER1_%1
CF_REMOTEUSER2_%1
CF_IR_%1
CF_INFOHIDE_%1
CF_KEYPADLOCK_%1
CF_DISPLAYMODELOCK_%1
CF_TESTPAT_%1
CF_BACKGND_%1
OPTION
SETUP
CF_SOURCESVIDEO_%1
CF_SOURCEDP_%1
CF_SOURCEHDBASET_%1
CF_SOURCELOCK_%1
CF_ALTITUDE_%1
CF_SOURCEVGA1_%1
CF_SOURCEVGA2_%1
CF_SOURCEHDMI1_%1
CF_SOURCEHDMI2_%1
CF_SOURCEVIDEO_%1
CF_EXTRON_%1
CF_PJLINK_%1
CF_AMX_%1
CF_HTTP_%1
Standard format
commands commands parameter(%1=)
Item
Expand format
note
Category
reply
CR_12VTRIGGER 0~1 Check 12V Trigger setting
0 off
1on
CR_BEEP 0~1 Check Beep setting
0 off
1on
CR_AUTOPOWERON 0~1 Check Direct Power On setting
C29 0 off
C28 1 on
CR_AUTOPOWEROFF 0~180(min) Check Auto Power Off setting
0 off
UP Increase setting value (+5) from current setting
DN Decrease setting value (-5) from current setting
CR_SLEEP 0~990(min) Check Auto Power Off setting
0 off
UP Increase setting value (+10) from current setting
DN Decrease setting value (-10) from current setting
CR_QRESUME 0~1 Check Quick Resume setting(EK601W only)
0 off
1on
CR_STANDBYPOWER 0~1 Check Standby Power setting
0 Normal
1 Eco
CR_LAMPREMINDER 0~1 Check Lamp Reminder setting
0 off
1on
CR_LAMPMODE 0~2 Check Lamp Mode setting
0 Bright
1 ECO
2 Power
CR_LAMPPOWER 0~5 Check Lamp Power setting
0280W
1300W
2310W
3330W
4350W
5365W
4-23 CF_LAMP_RESET Lamp reset
CR_FILTER 0~1 Check Filter Installed setting
0no
1 yes
CR_FILTERREMINDER 0~4 Check Filter Reminder setting
0 off
1 300hrs
2 500hrs
3 800hrs
4 1000hrs
4-26 CF_FILTER_RESET Reset Filter setting
4-27 CF_INFO Display Information
4-28 CF_FACTORY_RESET Do Factory reset function
A-1 C01 Power Off (Directly Off)
A-2 CR0
00~99
Get the projector's status
0 = RESET /* system is in the reset power state */
1 = STANDBY /* system is in the standby power state */
2 = ACTIVE /* system is in the active power state */
3 = COOLING /* system is cooling */
4 = WARMING /* system is warming */
5 = POWERUP /* this state indicates system is powering up */
A-3 CR1
00~08
Get the information of input source
01 = VGAI
02 = VGA2
03 = HDMI1
04 = HDMI2
05 = Video
06 = S-Video
07 = DisplayPort
08 = HDBaseT
A-4 CR3 0~ Lamp time read (hours)
A-5 CR4 "%1_%2_%3"
Get the temperature data inside the projector
%1 = Temperature of Sensor 1(There is only one thermal sensor in our
system)
B-1 C00 Power On
B-2 C02 Power Off
B-3 CF_KYTESTPATTERN Test Pattern
B-4 CF_KYMOUSESWITCH Mouse Switch
B-5 CF_KYF1 F1
B-6 CF_KYF2 F2
B-7 CF_KYMODE Mode
B-8 CF_KYAVMUTE AV Mute
B-9 C3C ↑
B-10 C3B ←
B-11 C3A →
B-12 C3D ↓
B-13 C3F ENTER
B-14 CF_KYINFO Info.
B-15 CF_KYRESYNC Source
B-16 C89 Re-Sync
B-17 C09 Volume +
B-18 C0A Volume -
B-19 CF_KYMENU Menu
B-20 C8E V Keystone ▲
B-21 C8F V Keystone ▼
B-22 CF_KYFORMAT Format
B-23 CF_KYZOOM Zoom
B-24 C05 VGA1 (1)
B-25 C34 S-Video (2)
B-26 C36 HDMI1 (3)
B-27 C38 HDMI2
B-28 C06 VGA2 (4)
B-29 C07 Video (5)
B-30 C17 DisplayPort (9)
Remote
Control
4-21
4-22
4-24
4-25
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
Others
Remote Control key
CF_FILTER_%1
CF_FILTERREMINDER_%1
CF_QRESUME_%1
CF_STANDBYPOWER_%1
CF_LAMPREMINDER_%1
CF_LAMPMODE_%1
CF_LAMPPOWER_%1
CF_BEEP_%1
CF_AUTOPOWERON_%1
CF_AUTOPOWEROFF_%1
CF_SLEEP_%1
CF_12VTRIGGER_%1
OPTION
