Electrolux EDW7505HSS1B User Manual DISHWASHER Manuals And Guides 1104514L
User Manual: Electrolux EDW7505HSS1B EDW7505HSS1B ELECTROLUX DISHWASHER - Manuals and Guides View the owners manual for your ELECTROLUX DISHWASHER #EDW7505HSS1B. Home:Kitchen Appliance Parts:Electrolux Parts:Electrolux DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher NOTE: Put unit on its back being careful not to pinch the Water Drain Hose. Installation Instructions 1. Remove two (2) screws at front of the kickplate assembly using a #2 Phillips screw driver. 2. Tilt and pull forward to remove see figure 1. IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance to open door. 2. Property Damage Do not use the furnished drain hose or a rubber garden hose for the water supply line. Either of these hoses can burst. Flooding may occur and cause property damage. Floor should be flat and free of any obstruction. IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further. NOTE: It is not necessary to remove the outer door for installation. Electric Shock Hazard INSTALLER: Leave Installation Instructions with owner. Outer OWNER: Read your dishwasher Use and Care Guide. It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher. Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. Door , before installing Height of Cabinet Opening Toeplate For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher. Figure 1 Kickplate Weight Keep children away from the front of the dishwasher so that they are not accidentally hit by the door during loading or unloading or if door should unexpectedly open. The weight of the door can cause injury. Wrap 90 ° elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve. When tightened, elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4. , Cabinet Preparation: As a precaution, it is recommended, but not required that the cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/ moisture damage. Tools and Materials Needed for Installation (Not Included) Drill, Electric • • • • • Drill Bit 118" Driver, Socket 8/32",114",8118" Flaring Tool/Tube Cutter (for copper tubing) Flashlight Level • • Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers • Safety Glasses • • • Saw, Keyhole or Vf, 1 _/2"to 2" Hole Cutters Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) Tape, Electrical or Duct • Tape, Measuring • • Wire Stripper or Utility Knife Wrench, Hex-end • Wrenches, 2 Adjustable or 2 Pipe wrenches • • • • Electric Shock Hazard Observe all local codes and ordinances for electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. , NOTE: Pull the hose from "End Storage Location" side. See images below to connect the Drain Hose. L 2. Take drain Hose out of dishwasher and find the end that doesn't have the black rubber material. Use only the spring clamp that is provided in the accessory kit, place spring clamp over one of the hoses. See Image Below. 0 34W' (86.7cm) 2 348h?' (87.2cm) 6 34Vf (87.6cm) 9 Make sure your location has the correct drain, water, and electrical outlets to make the connections. Do not install unit under a cooktop range. Damage to tub or other components will occur. Electricalwater and draidines must be confined to shadedarea Preferred drain areas 2. Move dishwasher to front of installation area. 3. Loosen the rear leveling legs by turning counterclockwise. to chart for number of turns. Refer Dishwasher Anchoring 4. Install the Cabinet Seal Kit (Instructions included in Kit) 5. Choose one of the methods of attachment below to secure unit, holes need to be pre-drilled using a #5 drill bit regardless of the option chosen: b. Top Mount Cabinet Clips (to be used when Side Mount is not an available option) Locating the Connections 1. Review dimensions in Figure 2 to locate dishwasher's drain, water, and electrical connections. 2. All utilities must be routed in shaded area in the Figure 2. Disconnect power before starting Hose Attached To Dishwasher Remove Plug Of Hose installation. To install the Side Mounting Clips. NOTE: Install Side Mount Brackets before unit is installed into the cabinet. Insert screws into the front holes of the mounting clips only. (See image below) Hose Shipped Inside Dishwasher Clamp 3. Cut access holes for the Electrical, Water and Drain hoses in the shaded areas as shown in Figure 2. 4. The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. 3. 5. Pull electrical cable through hole into installation area. 4. 6. Be sure water inlet valve is protected from freezing. If valve freezes and ruptures, flooding may occur. 7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Extra hose length is necessary. High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of V4"may be used. A shut-off valve installed outside dishwasher cabinet is best. 8. Plastic End CAUTION: Use extreme care in mounting the dishwasher as to not scratch, bump or otherwise damage the console or tub. Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up (preferred method) or down as shown in the illustrations below. (Use extreme caution when the clips are in the down position while installing the dishwasher). Note: Locate the electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly. See Figure 4. Determine where you will connect to hot water supply. Review Figure 4 and note the location of water inlet valve. Determine where you will connect the drain hose. Use if measures Take the plastic side of the drain hose and insert it into the hose that is already attached to the dishwasher make sure hose ends are flush against each other. See image below. Secure the spring clamp 1/8" from large end of black hose to the plastic side that was inserted for best sealing results. See Image Below. Plastic Ends of Hoses Flush 34V8" to 35" screw Use if measures 34" to 34V8" Route water supply line into installation area. 9. Stand dishwasher back upright for further installation. IMPORTANT: Incoming hot water temperature should least 120°F (49°C). Water pressure should be between 20-90 psi. (for copper tubing) (for iron pipe plumbing) Parts You Will Need* 34" (86.4cm) a. Side Mount Cabinet Clips (Preferred Method of attachment) IMPORTANT: • EndStorageLocation Assembly Locate water inlet valve behind kickplate on bottom left underside of unit.See Figure 4. The valve has a V?' NPT female fitting. Remove Plug Failure to follow this warning can result in serious injury. To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit. k Chart Number of Turns to Adjust Levelers complete. (The Installation Instructions are located in the Kit) Do not push down on open door. Cut Hazard NOTE: Cabinet Seal Kit (Kit # 154662101). This kit provides a seal between the unit and cabinets once installation is Kickpiat_ , Tip Over Hazard Do not use dishwasher until completely installed. 2 Top Screws dishwasher. Measure height of cabinet opening from underside of countertop to floor. Check chart for height opening and suggested adjustment. Leg Leveler Adjustment NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed. Read all instructions DrainH0seC0nnectOr ':::::: Printed in U.S.A. 154744001 10/10 be at screw Hose Attached to Dishwasher (Not Included) Drain Hose Clamp, 1W' Diameter Brass Elbow, 90 ° with a 3/8"National Pipe Thread Conduit Connector (UL Listed) Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) 4%" max. (5/r6"rain. clearance required from unit to underside of countertb 13/4" A To install using Top Mount Cabinet Clips: Figure 2 Front If required: • "Y" Branch Tailpiece and Connector Kit (See Step 4) • Air Gap Kit (See Step 4) Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary. Left _ 245/8"_ NOTE: Install Top Mount Clips before unit is installed into the cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below) // / All the parts can be found at local hardware, electrical and plumbing supply stores. ,' ,, Doorin90 openposition ///////////////////// k¸ Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. \ waterinletand powersu_pl_ location(middlebottomrear) *Heightonlyadjustable td N" max.when installedin35tnax4tandard cabine#:utout S DIMENSIONS Figure 3 INSLJ_ATION INSTALLATION. DO NOT BLANKET INCLUDE MAY INSLJ-ATION BE COMPRESSED Water Line Brass Elbow (Not Included) (Not Included) Tighten Spring Clamp !I UPON Electrical Line Figure 4 I If levelers need to be removed, make sure that the floor is free of all obstructions. , 5. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. 7. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor. Green Wire to Green Wire (Ground) Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow 5/16" below underside of countertop to top of console. , 1. Review Figures 7, 8 and 9 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. 6. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. , Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 5a. , Junction Box Junction Box Cover Figure Figure 4. 5a Blac_ Wire to Black Wire Entry Must be Above , Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. White Wire to White Wire (Neutral) (Hot) 6a Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. ,,y,, Branch Replace junction box cover. Screws Electric Shock Hazard Tailpiece Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. 10. Check that the dishwasher is level from front to back by taking out the lower rack, place level on the lower rack wheel support at the bottom of the tub. See Figure 5b. Sink at Right Sink Failure to follow this warning could result in death or serious injury. at Left 2" Drain Hose Hole 11. Adjust levelers up or down until dishwasher is level. Cabinet Attach Weight Keep children away from the front of the dishwasher so that they are not accidentally hit by the door during loading or unloading or if door should unexpectedly open. The weight of the door can cause injury. To prevent the possibility of damage to dishwasher, replace factory installed outer door screws with factory supplied wood panel screws, The EDW7505HSS & EDW7505HPS can be installed with a fully integrated, buyer supplied custom door panel. Clip Holes need to be pre-drilled using a #5 drill to secure unit. Figure 7 The custom panel should be 1/2" to 3/4" (19mm) thick. 12. Screw mounting brackets firmly to cabinet using screws provided Cabinet Seal in literature packet. See Image Below. Side Cabinet Seal Cut Hazard The drain hose loop must be at least 32" high f!'om the floor to insure proper drainage. Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 7. , Failure to follow this warning may result in injury. Items provided with the unit: Six 1V8"screws for mounting the custom wooden panel to the dishwasher. Tools you will need to install the Custom Wood Panel: # 32 Drill Bit (7/64") 2 # 7 _/2"screws (Optional) INSTALLING Figure 5c Figure Air 5d 13. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly until door opens and closes freely. Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. Gap Leveling Leg Failure to follow this warning could result in electric shock. Water Figure check these items: Line Electrical 6b Line check these items: [3 [3 All four leg levelers are positioned properly. [3 Cabinet Seals are positioned on the sides and top of the dishwasher. Property Damage Do not solder within 6" of the water inlet valve. Damage to the plastic parts in the valve may occur. [3 Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur. [3 Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may rupture and flooding may occur. Water and electrical lines are straight out in front of the dishwasher. Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher. 3. If you connect to a sink trap, local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 8. An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). 4. If you connect to a disposer, the large end of drain hose will fit. Figure 9(a). The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 9(b). Remove protective film before replacing toe and kickplate then replace Toe and Kickplate. Note: When replacing Toe and Kickplate hand tighten screws. Water Line 2. 3. 4. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn offwater supply at shut-off valve. Route water line to water inlet valve as shown in Figure 4. While firmly pulling water supply line into 90 ° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. Turn on water supply and check for leaks. Electrical Supply 1. 2. 3. Remove junction box cover and pull house wiring into junction box. See Figures Below. Use a UL listed conduit connector (not included) at box to stabilize wiring. Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight. Water and drain lines have no kinks and move freely behind the dishwasher. [3 Water supply is turned on. [3 Joints are free of leaks. [3 Wiring connections to junction box are tight all access panels are secured back in place. [3 Replace kickplate. See Figure 1 [3 Drain hose is assembled to Drain Hose Connector. [3 All packing materials and consumer literature have been removed from inside unit. [3 [3 [3 Cut for 1. [3 5/8" \ connection. _YY22UYU--_T- / /fits / (_ -- Figure 9(a) Cut for 3/4 _Larger end of hose disposer inlet fitting. Drain Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. II I1", // Failure to follow these instructions could result in death or serious injury. NOTE: The door panel cannot exceed 12 pounds. Thiekn_: W' _1 Weight: 12Ibs,,max. Dishwasher is level and securely fastened. Open and close door to make sure it does not hit surrounding cabinet or countertop. Make sure that all wire ties are removed from the Adjustable Rack Assembly, Versa Tray, Utility Tray and Silverware Baskets. /// ', " "lI &/ [3 On EDW7505HSS and EDW7505HPS press and hold SANTIZE touchpad for 8 seconds before first use. [3 At first fill, approximately 2 minutes make sure water completely covers filter surface. [3 At pump-out: (pump-out is either when the cycle is completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. Drain i' - Floor into , / Separate Trap Sink at Right 2" Drain Hose Hole Figure 4. Open the door and use the six screws supplied to secure the panel to the door. _aX. 2 Pilot_[ill h01e_'_ :t Operate the machine through at least one fill and pump-out, checking the following items: //i _C Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. 3. Hook the panel screws into the rectangular openings of the metal panel on the dishwasher door. 6 PiLotdrillholes ate All wiring connections must be enclosed in the junction box. This unit has copper lead wires. 2. The two short screws go into the back of the panel 1 417/32" from the upper edge of the panel and 9/_6"from the edge of the panel. Insert the short screws into the panel, leaving Vs" of space between the screw head and the panel. Hose ! Do not connect the dishwasher to the power supply until the appliance is permanently grounded. 1. Fit the handle onto the panel according to the manufacturer's instructions. (NOTE: A handle should be used rather than a knob. A knob does not provide enough grip.) 23d=" / Drain Air Gap /q Refer to the Figure 10 for instruction references. (%"dia,:×_A"mA depth) Grounding Instructions: The dishwasher must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. PANEL connection. Electric Shock Hazard Sink at Left THE CUSTOM 9(b) The drain hose loop must be at least 32" high f!'om the floor to insure proper drainage. [3 Check water connections again for leaks. Figure 10 ADJUSTING THE DOOR SPRINGS Before you push the dishwasher into the cabinet opening, test the door to make sure it stays in place at any angle. If it tends to fall down, adjust the tension of the door springs on the sides of the machine by moving them one hole farther back. If the door moves to close, adjust the tension of the door springs on the side of the machine by moving them one hole forward.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Fri May 06 04:13:47 2011 Author : Title : Subject :EXIF Metadata provided by EXIF.tools