Electrolux EI24ID30QB0A User Manual DISHWASHER Manuals And Guides 1403214L
User Manual: Electrolux EI24ID30QB0A EI24ID30QB0A ELECTROLUX DISHWASHER - Manuals and Guides View the owners manual for your ELECTROLUX DISHWASHER #EI24ID30QB0A. Home:Kitchen Appliance Parts:Electrolux Parts:Electrolux DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher Figure 3 CD.808 936 619 Installation Instructions INSTALLER: Leave Installation Front Closed ,--23¾"(60,3 cm)_ ,. 24V,"(61,5cm)_ NOTE: Put unit on its back being careful not to pinch the Water Drain Hose. 1. Remove two (2) screws at the top the kickplate assembly Instructions with owner• 33¾" 1 is provided with water heating feature. The dishwasher is intended to hot water supply. Opendoor ]rr ® IMPORTANT: Drain, water, and electrical roughed-in before going any further. Failure to follow this warning can result in serious injury. Cut Hazard NOTE: If dishwasher is installed back must be fully enclosed. To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit. _n_elr _:pplnY/Wate r_ lines should be (Not Included) Drill, Electric • • • • Driver, Socket 5/32", 1/4", 5/16" Flaring Tool / Tube Cutter (for copper tubing) Flashlight Level • Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers • • • • • • • • • • Electric Shock Hazard Observe all local codes and ordinances for Brass Elbow (Not Included) tip Figure 1. (90,8cm) m_x.** I will Ebctrical, water, and drain lines must be confined to shaded area• Preferred Drain Areas 24" (60,96cm') mfn. (45,7cm) and Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. 3½" (8,89 cm) min.to _/' 4½"(11,43 cm) max. /_H_/ cm) max. standardcabinetrycutout. (5/16"[0,8cm] min. ¼" (3,1 cm) 2¼" clearance required from unit to underside of c0untert0p.) cm) _/ 1" (2,5 \ 2¼"4'_ (5,7 cm)' 24" (61cm) from underside 1. Review dimensions in Figure 2 to locate dishwasher's water, and electrical connections• 2. All utilities must be routed in shaded area in the Figure 2 of countertop area. Anchoring Choose one of the methods of attachment below to secure unit, holes need to be pro-drilled using a _5 drill bit regardless of the option chosen: a. Side Mount Cabinet Clips (Preferred Method of attachment) b. Top Mount Cabinet Clips (to be used when Side Mount is not an available option) CAUTION: Use extreme care in mounting the dishwasher as to not scratch, bump or otherwise damage the console or tub. drain, ® To install the Side Mounting Clips. Note: install Side Mount Brackets before unit is installed into the cabinet, insert screws into the front holes of the clips only. Use extreme caution when fixing the screws, not to cratch dishwashers or kitchen cabinet• range, Damage to tub or other components 34"(86,36cm) mfn.to 35¾" height of cabinet opening Dishwasher Electrical Line 2 Make sure your location has the correct drain, water, and electrical outlets to make the connections• Do not install unit under a cooktop occur. Measure to floor• .• Move front of installation Adjust dishwasher the levelling to legs. Locating the Connections electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. • Drain HoseClamp, 1 1/4" (3,1 cm) Diameter • Brass Elbow, 90 ° with a 3/4" ( Q 2 cm )-11.5 NH to 3/8" ( Q 2 cm ) NPT Compression fitting • Conduit Connector (UL Listed) • Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) electrical 1. 4. Parts You Will Need*(Not Included) "klf required: • "Y" Branch Tailpiece and Connector Kit (See Step 8 ) • Air Gap Kit (See Step 8 ) All the parts can be found at local hardware, plumbing supply stores• 333A,, Adjustable to 353A'' Water line (Not Included Safety Glasses Saw, Keyhole or 1/2", 11/2" to 2" Hole Cutters Screw Drivers, Slotted and a2 Phillips (magnetic preferred) Work gloves Tape, Electrical or Duct Measuring Tape Wire Stripper or Utility Knife Wrench, Hex-end Wrenches, 2 Adjustable (for copper tubing) or 2 Pipe wrenches (for iron pipe plumbing) 6 Figure 4 Locate water inlet valve behind kickplate on bottom left underside of unit. See Figure 4 The valve has a 3/8" ( 1 cm ) NPT male fitting• 4. Connect the 90 ° elbow (not included) to water inlet valve• When tightened, point elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4. Cabinet Preparation: As a precaution, it is recommended, but not required that the cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/moisture damage. Installation Figure at end of a cabinet, sides and 3. Tools and Materials Needed for it into IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance between the wall and the open door. 2. Floor shouldbe flat and freeof any obstruction, Do not push down on open door. % placing l ® Electric Shock Hazard Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. Parts Included: before UPON INSTALLATION. installed. • seal to dishwasher :_)** to 353,4 " For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher. Tip Over Hazard Do not use dishwasher until completely • ," Heightonly adjustableto 35%"(90,8cm)max when *DIMENSIONS DONOTINCLUDE INSULATIONinstalledin 35¾" (90,8ore)maxstandard cabinetrycutout. INSULATION BLACKET MAYBECOMPRESSED dishwasher. The dishwasher cabinet to 35¾" • for connection NOTE: Install the cabinet (86ore), Adjustable 2. Tilt and pull forward the kickplate to remove it. - see Figure 1. NOTE: It is not necessary to remove the outer door for installation• Figure before installing Figure 5 _,_ 22½"(57,1 cm)÷ OWNER: Read your dishwasher Use and Care Manual. It contains important safety information for operating this appliance• It also has many suggestions for getting the best results from your dishwasher• Read all instructions Open Door 501A"(127,6cm) \ Note: Locate the electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly• See Figure 4. Determine where you will connect to hot water supply. Review Figure 4 and note the location of water inlet valve• Determine where you will connect the drain hose. 3. Cut access holes for the Electrical, Water and Drain hoses in the cabinet within the shaded areas as shown in Figure 2. 4. The dishwasher operates on a 120 volt, 60 Hz electrical supply• Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. 5. Pull electrical cable through hole into installation area. 6. Be sure water inlet valve is protected from freezing• If valve freezes and ruptures, flooding may occur• 7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Extra hose length is necessary High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of 1/4" may be used. A shut-off valve installed outside dishwasher cabinet is best. 8. Route water supply line into installation area. 9. Stand dishwasher back upright for further installation• IMPORTANT: Incoming hot water temperature should be at least 120°F (49°0). Water pressure should be between 20-90 psi. (See image below) (_ To install using Top Mount Cabinet Clips: Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary. NOTE: Install Top Mount Clips before unit is installed into the cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below) 5. 6. 7. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor. Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow 5/16" (0,8 cm) below underside of countertop to top of console. Check that dishwasher is level from side to side by placing a level against the top front section of the tub. See Figure 7a. 8. Adjust levelers up or down until dishwasher Figure Do not solder Damage within Property Damage 6" (15,24 cm) of the water to the plastic inlet valve. parts in the valve may occur. Use care that no sealer, dirt, or other objects Damage to the filter screen may occur. is level. See Figure 7b. 7a Be sure the dishwasher valve will be kept from rupture and flooding enter the valve. is placed where the water inlet freezing. If the valve freezes, it may Electric may occur. Grounding Water Line 1. Figure 2. 3. 7b 4. 2. 3. Figure 8 connected to the appliance's or lead. It is the consumer's metal, and Electric Shock Hazard equipment grounding terminal responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes 3. Do not connect the dishwasher to the power appliance is permanently grounded. supply until the All wiring connections must be enclosed in the junction box. This unit has copper lead wires. Joining aluminum building wire to stranded copper wire 4. should be done by a qualified electrician using materials recognized by UL and local codes. Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. Failure to follow these instructions could result in death or serious injury. fits disposer inlet fitting F (Ground) W_. h "_L_ '_./_z'_ White Wire to White Wire v to Black Wire (Hot) i (Neutral) Replace junction box cover.See Figure Cut Hazard Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. Larger end 'hose Green Wire to Green Wire _ Holes need to be pre-drilleld using a 05 drill to secure unit 10. Screw mounting brackets firmly to cabinet using screws provided in installation packet. See Figure 8 11. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly, adjust rear foot if small correction is needed until door opens and closes freely. Adjust the levelling legs. Failure to follow this warning could result in death or serious injury Failure to follow this warning may result in injury. Figure 9. Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. If you connect to a sink trap,local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 13 An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). If you connect to a disposer, the large end of drain hose will fit. Figure 14 (a) The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 14 (b). and ordinances. Remove junction box cover and pull house wiring into junction box. See Figure 9 Use a UL listed conduit connector (not included) at box to stabilize wiring. Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight. Figure 9 Instructions: The dishwasher must be connected to a grounded permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water supply at shut-off valve. Route water line to water inlet valve as shown in Figure 4. While firmly pulling water supply line into 90 ° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. Turn on water supply and check for leaks. Electrical Supply 1. Shock Hazard 14(a) Cut Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. Failure to follow this warning could result in electric shock. %"(1,6 cm) connection. Drain Air Gap f__ Sink at Left _ Black Wire to Black Wire (Hot) _ / ]/ ._ White Wire to White Wire (Neutral) / "_ _ " Through Floor into 10 Separate Trap Remov_ Knockout Plug in Disposer i Review Figures 12, 13 and 14 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. Figure 14(b) Sink at Right Drain Hose Hole The drain hose loop must be at least 32"(80 cm) high fbom the floor 5. Entry Must be Above 11 7. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. Secure drain hose to sink drain, disposer, or separate trap with a 8. clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. Be sure unit does not rest on drain hose. It should be free of 6. g#y," Branch Tailpiece Water Line Electrical Line Sink at Right Sink at Left 2"Drain Hose Hole Figure Water and electrical lines are straight out in front of the dishwasher. [] All three leg levelers are positioned properly. [] Cabinet Seals are positioned dishwasher. on the sides of the [] Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher. [] Water supply is turned on. [] Joints are free of leaks. [] Wiring connections to junction box are tight all access panels are secured back in place. [] Replace kickplate. [] Drain hose is connected [] All packing materials and consumer been removed from inside unit. [] Dishwasher [] Open and close door to make sure it does not hit surrounding cabinet or countertop. Make _L/re that all wire ties are removed from the rack assembly 2" (5,08 cm) to insure proper drainage. o check these items: Water and drain lines have no kinks and move freely behind the dishwasher. ._._,,_,_ Figure 10 Figure [] 12 The drain hose loop must be at least 32" (80 cm) high from to insure proper electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. [] 2. If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 12. 11 properly to outlet. literature have is level and securely fastened. Operate the machine through at least one fill and pump-out, checking the following items: [] At first fill, approximately 4 minutes make sure water completely covers filter surface. [] At pump-out: (pump-out is either when the cycle is completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. [] Check water connections the floor drainage. See Figure again for leaks.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Mar 18 22:00:49 2014 Author : Title : Subject :EXIF Metadata provided by EXIF.tools