Electrolux EI30BM6CPSA User Manual MICROWAVE OVEN Manuals And Guides 1305447L

User Manual: Electrolux EI30BM6CPSA EI30BM6CPSA ELECTROLUX MICROWAVE OVEN - Manuals and Guides View the owners manual for your ELECTROLUX MICROWAVE OVEN #EI30BM6CPSA. Home:Kitchen Appliance Parts:Electrolux Parts:Electrolux MICROWAVE OVEN Manual

Open the PDF directly: View PDF .
Page Count: 24

Installation

Instructions Overthe Range

Microwave Oven

IQuestions ?Call 1-877=435-3287(US) .,. I

1=800=265-8352(Canada) v_ Visit our Websiteat:http://www.electroluxappliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•IMPORTANT - Savethese

instructions for local inspector's use.

•IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer -Be sure to leave these

instructions with the Consumer.

•Note to Consumer -Keep these

instructions for flJture reference.

•Skill level - Installation of this appliance requires

basic mechanical and electrical skills.

•Proper installation is the responsibility of the installer.

•Product failure due to improper installation is not

covered under the Warranty.

READ CAREFU LLY.

KEEP THESE INSTRUCTIONS.

pin 316902904

April 2012

Installation Instructions

CONTENTS

General information

Important Safety Instructions .................................. 3

Electrical Requirements .......................................... 3

Damage - Shipment/Installation .............................. 4

Parts Included .......................................................... 4

Tools You Will Need ................................................ 5

Mounting Space ...................................................... 5

Step-by-step installation guide

Placement of The Mounting Plate ...................... 6-8

Removing the Mounting Plate ...................... 6

Finding the Wall Studs .................................. 6

Determining Wall Plate Location .................. 7

Aligning the Wall Plate ................................ 8

Installation Types ............................................... 9-22

Hood Exhaust .................................................. 10-11

_ Outside Top ............................

Exhaust 12-15

Attach Mounting Plate to Wall ............ 12

Preparation of Top Cabinet ................ 13

Adapting Microwave Blower for

Outside top Exhaust .................. 13-14

Checking for Proper Damper

Operation ............................................ 14

Mount the Microwave Oven .......... 14-15

Adjust the Exhaust Adaptor ................ 15

Connecting Ductwork .......................... 15

]Outside Back Exhaust 16-19

Preparing Rear Wall for

Outside Back Exhaust .......................... 16

Remove Blower Plate .............................. 16

Attach Mounting Plate to Wall ............ 17

Preparation of Top Cabinet ................ 17

Adapting Microwave Blower

for Outside Back Exhaust ................ 17-18

Mount the Microwave Oven ................ 19

[] Recirculating ........................................ 20 _ 2 2

Attach Mounting Plate to Wall ............ 20

Preparation of Top Cabinet ................ 20

Check Blower Plate ............................ 21

Mount the Microwave Oven .......... 21-22

Installing or Change the

Charcoal Filter .................................... 22

Before You Use Your Microwave .......................... 23

Template Information ............................................. 24

2

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

This product requires a three-prong grounded outlet.

The installer" must perform a ground continuity check

on the power" outlet box before beginning the

installation to insure that the outlet box is properly

grounded. If not properly grounded, or" if the outlet

box does not meet electrical requirements noted

(under ELECTRICAL REQUIREMENTS), a qualified

electrician should be employed to correct any

deficiencies.

CAUTION: For personal

safety, remove house fuse

or open circuit breaker

before beginning

installation to avoid severe

or fatal shock injury.

CAUTION: For personal safety, the mounting surface

must be capable of supporting the cabinet load, in

addition to the added weight of this 63-85 pound

(28.5-38.5 kg) product, plus additional oven loads of

up to 50 pounds (22.7 kg) or a total weight of

113-135 pounds (51.3-61.2 kg).

CAUTION: For personal safety, this product cannot

be installed in cabinet arrangements such as an island or

a peninsula. It must be mounted to BOTH a top cabinet

AND a wall.

NOTE: For easier installation and personal safety, it is

recommended that two people install this product.

IMPORTANT - PLEASE READ CAREFULLY. FOR

PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED TO AVOID SEVERE OR

FATAL SHOCK.

Ensureproper

groundexists

beforeuse

The power cord of this

appliance is equipped with a

three-prong (grounding)

plug which mates with a

standard three-prong

(grounding) wall receptacle

to minimize the possibility

of electric shock hazard

from this appliance.

You should have the wall receptacle and circuit checked

by a qualified electrician to make sure the receptacle is

properly grounded.

Where a standard two-prong wall receptacle is

encountered, it is very important to have it replaced

with a properly grounded three-prong wall receptacle,

installed by a qualified electrician.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT,

DEFORM OR REMOVE ANY OF THE PRONGS

FROM THE POWER CORD. DO NOT USE WITH

AN EXTENSION CORD.

ELECTRICAL

REQUIREMENTS

Product rating is 120 volts AC, 60 Hertz, 15 amps and

1.6 kilowatts. This product must be connected to a

supply circuit of the proper voltage and frequency.

Wire size must conform to the requirements of the

National Electrical Code or the prevailing local

code for this kilowatt rating. The power supply

cord and plug should be brought to a separate

15- to 20- ampere branch circuit single grounded

outlet. The outlet box should be located in the

cabinet above the microwave oven. The outlet box

and supply circtfit should be installed by a qualified

electrician and conform to the National Electrical

Code or the prevailing local code.

3

Installation Instructions

DAMAGE--SHIPMENT/

INSTALLATION

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for repair

or replacement.

•If the unit is damaged by the customer, repair or

replacement is the responsibility of the customer.

•If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer

and installer

PARTS INCLUDED

HARDWARE PACKET

PART

/

+

!

Wood Screws

(1/4" X 2")

ToggleBolts(and

wing nuts)(3/16"x 3")

Sel?AligningMachine

Screws(1/4"-28x 31/4'')

NylonGrommet

(for metalcabinets)

QUANTITY

2

You will find the installation hardware contained in

a packet with the unit. Check to make sure you have

all these parts.

NOTE: Some extra parts are included.

PARTS INCLUDED (CONT.)

ADDITIONAL PARTS

PART QUANTITY

TopCabinet

Template

RearWall

Template

Installation

Instructions

Use &

Care Guide

Separately

Packed

Grease

Filters

Exhaust

adaptor

Glass

Tray

Turntable

Ring

wire rack

Shelf

4

Installation Instructions

TOOLS YOU WILL NEED

# 1 Phillips screwdriver

Tin snips (for cutting

damper, if required)

Gloves

Safetygoggles

TTTI

Pencil

Scissors

(to cut template, if necessary)

dm==-

Saw (saber, hole or keyhole)

Ruler or tape measure and

t edge

L_

Electric drill with s/16",1/2"and %"

drill bits

Stud Finder or Hammer (optional)

Level

Carpentersquare

(optional)

Fillerblocksor scrap

woodpieces,if needed

for top cabinetspacing

(usedonrecessedbottom

cabinetinstallationsonly)

Duct and masking tape

MOUNTING SPACE

I

Backsplash

66" (167,6cm)

or MoreFrom

the Floorto the

Topof the

Microwave

BottomEdgeof

CabinetNeedsto

be30" (76,2cm)

or MoreFromthe

CookingSurface

NOTES:

•The space between the cabinets must be

30" (76.2 cm)wide and free of obstructions.

• If you are going to vent your microwave oven

to the outside, see Hood Exhaust Section for

exhaust duct preparation.

•When installing the microwave oven beneath

smooth, flat cabinets, be careful to follow the

instructions on the top cabinet template for

power cord clearance.

13-3/4"(34.9cm) min.

5

Installation Instructions

PLACEMENT OF THE MOUNTING PLATE

REMOVING THE MICROWAVE

OVEN FROM THE CARTON/

REMOVING THE MOUNTING

PLATE

[]Remove the installation instructions, filters, glass

tray and the small hardware bag. Do not remove

the Styrofoam protecting the front of the oven.

[] Fold back all 4 carton flaps fully against carton

sides. Then carefully roll the oven and carton over

onto the top side. The oven should be resting in

the Styrofoam.

Styrofoam_

[_ Pull the carton up and off the oven.

Cut the middle of the outer protective plastic bag to

remove the mounting plate

Screws Screws

Mounting Plate _t

[]Remove the screws fl'om the mounting plate.

This plate will be used as the rear wall template

and for mounting. Reinstall the screws into the

holes where they were removed.

I-_ FINDING THE WALL STUDS

Wall

Studs

Centeri i

-%

[]Find the studs, using one of the following

methods:

A. Stud finder - a magnetic device which

locates nails.

OR

B. Use a hammer to tap lightly across the

mounting surface to find a solid sound.

This will indicate a stud location.

_}_ After locating the stud(s), find the center by

probing the wall with a small nail to find the edges

of the stud. Then place a mark halfway between

the edges. The center of any adjacent studs should

be 16" (40.6 cm) or 24" (61 cm) from this mark.

[]Draw a line down the center of the studs.

THE MICROWAVE MUST BE CONNECTED TO

AT LEAST ONE WALL STUD.

6

Installation Instructions

I_1 DETERM INING WALL PLATE LOCATION UNDER YOUR CABINET

Plate position--beneath flat bottom

cabinet ILl

tJ

I t_ c !ll ......

_ i _i I uraw a vertical line on

"_. the wall at the center of

At least30" _1 the 30" wide space.

Tape the Rear Wall

Template onto the wall

matching the centerline

and touching the

bottom of the cabinet.

Plate position--beneath framed

recessed cabinet bottom

I

I I

I I

I I

C

33" to Cooktop

Draw a vertical line on the wall at the center of the

30" space.

Tape the Rear Wall Template onto the wall

matching the centerline and touching the bottom

binet frame.

Plate position--beneath recessed

bottom cabinet with front overhang

!;

Draw a line on the

back wall equal to the

depth of the front

overhang.

33" to Cooktop

Your cabinets may have decorative trim that

interferes with the microwave installation. Remove

the decorative trim to install the microwave properly

and to make it level.

THE MICROWAVE MUST BE LEVEL.

Use a level to make sure the cabinet bottom is level.

If the cabinets have a front overhang only, with no

back or side frame, install the mounting plate down

the same distance as the front overhang depth. This

will keep the microwave level.

[_ Measure the inside depth of the front overhang.

[_ Draw a horizontal line on the back wall an equal

distance below the cabinet bottom as the inside

depth of the front overhang.

[_ For this type of installation with front overhang

only, align the mounting tabs with this horizontal

line, not touching the cabinet bottom as described

in Step D.

7

Installation Instructions

ALIGNING THE WALL PLATE

Hole B

REAR WALL

Centerline

notches "a

Draw a Vertica! Line

on Wall from Center

of Top Cabinet

Horizontal Line

CAUTION: Wear gloves

to avoid cutting fingers on

sharp edges.

Area E

u

u

u

u

' Hole A Horizontal Line

!

Draw a Horizontal line on wall from

bottom of "Rear Wall Template".

I_ Draw a Vertical line on the wall at the center of the

30" wide space.

I_ Draw a Horizontal line on the wall at the bottom of

"Rear Wall Template".

I_ Drill 5/8" holes for toggle bolts on 2 locations

(Hole A, Hole B) but if the location of hole

is same as that of stud, drill a 3/16" hole for wood

screw. In other words, toggle bolt can not be used

to the location of stud.

NOTE: DO NOT MOUNT THE PLATE AT THIS

TIME.

NOTE: Holes A and B are inside area E. If both of

A and B are not in a stud, find a stud somewhere in area

E and draw a forth circle to line up with the stud. It is

important to use at least one wood screw mounted

firmly in a stud to support the weight of the

microwave. Set the mounting plate aside.

8

Installation Instructions

I-2-1 INSTALLATION TYPES

This microwave oven is designed for adaptation to

the following three types of ventilation:

A. Outside Top Exhaust (Vertical Duct)

B. Outside Back Exhaust (Horizontal Duct)

C. Recirculating (Non-Vented Ductless)

(Choose A, B or C)

NOTE: This microwave is shipped assembled for

Recirculating. Select the type of ventilation required

for your installation and proceed to that section.

OUTSIDE TOP EXHAUST

(VERTICAL DUCT) OUTSIDE BACK EXHAUST

(HORIZONTAL DUCT)

Adaptorin Racefor

CUt_deTopBCaust

AdaptorMust Be

Movedto the Backfor

RECI RCU LATI NG

_-1 (NON-VENTED DUCTLESS)

On modelsshipped for

recirculating exhaust, a

di_oosable charcoal filter

isfactory installed to help

remove smoke and odors

9

Installation Instructions

INSTALLATION INSTRUCTIONS FOR EXTERNAL EXHAUST DUCTING

NOTE: If you need to install ducts, note that the total

duct length of 31/4" x 10" (8.2 x 25.4 cm) rectangular or

5" (10.5 cm) diameter/ 6" (15.2 cm) diameter round duct

should not exceed 120 equivalent feet (36.5 m).

Outside ventilation requires a EXTERNAL EXHAUST

DUCT.Read the following carefully.

NOTE: It is important that venting be installed using

the most direct route and with as few elbows as possible.

This ensures clear venting of exhaust and helps prevent

blockages. Also, make sure dampers swing freely and

nothing is blocking the ducts.

Exhaust connection:

The exhaust adaptor has been designed to mate with

a standard 31/4" x 10" (8.2 x 25.4 cm) rectangular duct.

If a round duct is required, a rectangular-to-round

transition adaptor must be used.

A 5"(10.5cm)/6" (15.2cm) diameter duct is acceptable to use

Maximum duct length:

For" satisfactory air" movement, the total duct length of

31/4"x 10" (8.2 x 25.4 cm) rectangular or 5" (10.5 cm)

diameter/6 "(15.2 cm) diameter round duct should not

exceedl20 equivalent feet (36.5 m).

Elbows, transitions, wall and roof caps,

etc., present additional resistance to airflow and are

equivalent to a section of straight duct which is longer

than their actual physical size. When calculating the total

duct length, add the equivalent lengths of all transitions

and adaptors plus the length of all straight duct sections.

The chart below shows you how to calculate total

equivalent ductwork length using the approximate feet

of equivalent length of some typical ducts.

DUCT PIECES

J

@

0

J

Rectangular-to-Round

TransitionAdaptor*

Wall Cap

90° Elbow

45° Elbow

90° Elbow

45° Elbow

RoofCap

StraightDuct6" (15,2cm)

Roundor 31/4``x 10"

(8,2x 25,4cm)Rectangular

EQUIVALENT

LENGTH

5 Ft,(1,5m)

40Ft, (12,2m)

10Ft, (3m)

5 Ft,(1,5m)

25Ft, (7,6m)

5 Ft,(1,5m)

24Ft, (7,3m)

1 Ft,(0,3m)

NUMBER

x USED

x ()

x ()

x ()

x ()

x ()

x ()

x ()

x ()

Total Ductwork

EQUIVALENT

LENGTH

Ft,orm

Ft,orm

Ft,orm

Ft,orm

Ft,orm

Ft,orm

Ft,orm

Ft,orm

Ft. or m

* IMPORTANT: If a rectangular to round transition

adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, in order

to allow free movement of the damper.

Equivalent lengths of duct pieces are based on actual tests

and reflect requirements tot good venting pertbrmance with

any vent hood.

10

Installation Instructions

EXTERNAL EXHAUST DUCTING

NOTE: Read these next two pages only if you plan to vent your exhaust to the

outside. If you plan to recirculate the air back into the room, proceed to page 20.

OUTSIDE TOP EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

DUCT PIECES

Roof Cap

EQUIVALENT NUMBER EQUIVALENT

LENGTH x USED = LENGTH

24Ft, (7,3m) x (1) 24Ft, (7,3m)

12Ft, (3,6m)StraightDuct 12 Ft,(3,6m) x (1) = 12 Ft,(3,6m)

(6'715,2cmRound)

Rectangular-to-Round 5 Ft, (1,5m) x (1) = 5 Ft, (1,5m)

TransitionAdaptor*

Equivalentlengthsof ductpiecesarebasedonactualtestsand

reflect requirementsfor goodventingperformancewith anyvent hood, Total Length = 41 Ft. (12.5 m)

*IMPORTANT: If a rectangular-to-round transition adaptor is used, the bottom corners of the damper

will have to be cut to fit, using the tin snips, ira order to allow fi'ee movement of the damper:

OUTSIDE BACK EXHAUST (EXAMPLE ONLY)

The following chart describes an example of one possible

ductwork installation.

EQUIVALENT NUMBER EQUIVALENT

LENGTH* USED = LENGTHDUCT PIECES x

'_ Cap (12,2m) x

Wall 40Ft,

3Ft, StraightDuct 3Ft, (0,9m) x

(31/g'x 10'78,2x 25,4cm

Rectangular)

(_ 90° Elbow 10Ft,(3 m) x

(1) 40Ft,(12,2m)

(1) = 3Ft, (0,9m)

(2) = 20Ft,(3 m)

Equivalentlengthsof ductpiecesarebasedonactualtests and

reflect requirementsfor goodventingperformancewith anyventhood, Total Length = 63 Ft. (19.2 m)

NOTE: For- back exhaust, care should be taken to align exhaust with space between studs, or"wall should be prepared

at the time it is constructed by leaving enough space between the wall studs to accommodate exhaust.

11

Installation Instructions

OUTSIDE TOP EXHAUST (Vertical Duct)

INSTALLATION OVERVIEW

A1. Attach Mounting Plate to Wall

A2. Prepare Top Cabinet

A3. Adapting Microwave Blower for

Outside Top Exhaust

A4. Check Damper Operation

A5. Mount Microwave Oven

A6. Adjust Exhaust Adaptor

AT. Connect Ductwork

IMPORTANT NOTES:

• Make sure the screws for the

blower motor and blower plate

are securely tightened when

they are reinstalled. This will

help to prevent excessive

vibration.

• Make sure the motor wiring has

been properly routed and secured,

and that the wires are not pinched.

_-_ ATTACH THE MOUNTING

PLATE TO THE WALL

i

Attach the plate to the wall using toggle bolts.

At least one wood screw must be used to attach

the plate to a wall stud.

_ Remove the from the bolts.toggle wings

_ Insert the bolts into the mounting plate

through the holes designated to go into drywall

and reattach the toggle wings to 3/4" (19 mm) onto

each bolt.

To use toggle bolts:

Mounting

Plate

Spacing for Toggles

More Than Wall

-_1_-_i-_-- Thickness

I

i Toggle Wings

Bolt End

_ lace the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed

flush against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

_ Tighten all bolts. Pull the plate away fl'om the wall

to help tighten the bolts.

12

Installation Instructions

I-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws, a

hole large enough for the power cord to fit through,

and a cutout large enough for the exhaust adaptor.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

TOP EXHAUST

] lace the microwave in its upright position,

with the top of the unit facing up.

Blower Plate

Backof

_--Microwave

O_ - Blower Motor

Screw

Remove the screw that holds the blower plate

to the microwave. Remove and save the screw

holding the blower motor to the microwave.

Careflflly pull out the blower unit. The wires

will extend far enough to allow you to adjust

the blower unit.

EndA___End B

Microwave

Roll the blower unit 90 ° so that fan blade

openings are facing out the top of the

microwave.

Before Rotation After Rotation

Backof

Microwave M icrowave

[]Place the blower unit back into the opening.

Backof

Microwave

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not

pinched, and that they are properly secured.

13

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

TOP EXHAUST

Secure blower unit to microwave with the screw

removed in Step 1. Make sure the screw is tight.

Replace blower plate with the screw removed in

Step 1. Make sure the screw is tight.

T

I

J

Backof

Microwave

[] Attach the exhaust adaptor to the top of the

blower plate by sliding it into the guides of the

blower plate.

Adaptor

k0cking Tab

Push in securely until it is in the locking tabs.

Take care to assure that the damper hinge is

installed so that the damper swings freely.

I-_ CHECK FOR PROPER

DAMPER OPERATION

Blower Plate Exhaust Adaptor

X ,,_-___----Damper

• Make sure tape securing damper is removed and

damper pivots easily before mounting microwave.

• You will need to make adjustments to assure proper

alignment with your house exhaust duct after the

microwave is installed.

I-_ MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using fillet" blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are

not used, case damage may occur from

overtightening screws.

NOTE: When mounting the

microwave oven, thread

power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord. []Lift tilt it

microwave,

forward, and hook

slots at back bottom

edge onto four lower

tabs of mounting

plate.

[] front of oven

up against cabinet

bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet.

14

Installation Instructions

MOUNT THE MICROWAVE

OVEN (cont.)

Cabinet Front

Cabinet Bottom Shelf

_ ;:Z_._ Filler Block

_Tq_f1TT,_111-"T Equiva,ent

/toDepth

!\\1 IU_-_ Self-Aligning Screw

Microwave Oven Top

_l_ Attach the microwave oven to the top cabinet.

[] Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two hill turns on

each screw.

I

[_ Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

[] Install grease filters. See the Owner's _lanual

packed with the microwave.

ADJUST THE EXHAUST

ADAPTOR

Open the top cabinet and adjust the exhaust adaptor

to connect to the house duct.

Back of

Blower Plate Damper Microwave

Side-to-Side Adjustment,

Slide the Exhaust Adaptor

as Needed

CONNECTING DUCTWORK

P_se D._t

]Extend the house duct down to connect to

the exhaust adaptor.

]Seal exhaust duct joints using furnance duct tape

for high temperature applicatiol_s.

15

Installation Instructions

OUTSIDE BACK EXHAUST (Horizontal Duct)

INSTALLATION OVERVIEW

BI. Prepare Rear Wall

B3. Remove Blower Plate

B3. Attach Mounting Plate to Wall

B4. Prepare Top Cabinet

BS. Adjust Blower

B6. Mount the Microwave Oven

IMPORTANT NOTES:

• Make sure the screws for the

blower motor and blower plate

are securely tightened when

they are reinstalled. This will

help to prevent excessive

vibration.

• Make sure the motor wiring has

been properly routed and secured,

and that the wires are not pinched.

PREPARING THE REAR WALL

FOR OUTSIDE BACK EXHAUST

You need to cut an opening in the rear wall for

outside exhaust.

• Read the instructions on the REAR

WALL TEMPLATE.

• Tape it to the rear wall.

• Cut the opening, following the instructions of the

REAR WALL TEMPLATE.

REMOVE BLOWER PLATE

Remove and save the screw that holds the blower

plate to the microwave. Lift off the blower plate.

Blower Plate

I _ _ _ Backof

Microwave

16

Installation Instructions

_] ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts.

At least one wood screw must be used to attach

the plate to a wall stud.

]Remove the toggle wings from the bolts.

}_ nsert the bolts into the mounting plate through

the holes designated to go into drywall and reattach

the toggle wings to 3/4" (19 mm) onto each bolt.

To use toggle bolts:

Mounting

Plate

Spacing for Toggles More

_-_i_,---Than Wall Thickness

roggle Wings

Bolt End

]Place the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed flush

against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careflfl to avoid pinching fingers

between the back of the mounting plate and the wall.

Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST

[]Remove and that holds blower motor

save screw

to microwave.

Blower Motor

"_" - _ Blower Motor

v .,_ Screw

Careflflly pull out the blower unit. The wires

will extend far enough to allow you to adjust

the blower unit.

EndA

17

Installation Instructions

ADAPTING MICROWAVE

BLOWER FOR OUTSIDE

BACK EXHAUST (cont.)

[] Roll the blower" unit 90 °

Before Rotation After Rotation

Backof

Microwave

Backof

Microwave

Rotate blower unit counterclockwise 180 ° .

Before Rotation

Back of

Microwave

After Rotation

M icrowave

[]Gently remove the wires from the grooves.

Reroute the wires through grooves on other side

of the blower unit.

Before Rerouting After Rerouting

Wires Routed ThroughRight Side Wires Routed Through Left Side

_6_ Roll the blower unit 90 ° so that fan blade

openings are facing out the back of the

microwave.

Before Rolling

M icrowave

After Rolling

Back of

Microwave

[]Place the blower unit back into the opening.

EndA

End

CAUTION: Do not pull or stretch the blower

unit wiring. Make sure the wires are not

pinched, and that they are properly secured.

NOTE: The blower unit exhaust

openings should match exhaust

openings on rear of microwave oven.

[ ecure the blower unit to the microwave with

the original screw.

_, Blower Plate

I _ Back of

,11_ Microwave

Blower Motor

Screw

[]Replace the blower in theplate same position

as before with the screw. Make sure the screw

is tight.

[]Attach the exhaust the of theadaptor to Fear

oven by sliding it into the guides at the top

center of the back of the oven.

Adaptor

Backof

Microwave

o

Locking Tabs

Guide

Guide

Push in securely until it is in the lower locking

tabs. Take care to assure that the damper hinge

is installed so that it is at the top and that the

damper swings freely.

18

Installation Instructions

MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not

used, case damage may occur from

overtightening screws.

NOTE: When mounting the

microwave oven, thread

power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord. []Lift tilt it

microwave,

forward, and hook

slots at back bottom

edge onto four lower

tabs of mounting

plate.

[]Rotate front of oven

up against cabinet

bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later:) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet.

Cabinet Front

Cabinet Bottom Shelf

Filler Block

Equivalent

to Depth

of Cabinet

Recess

Self-AligningScrew

Microwave OvenTop

[]Attach the microwave oven to the top cabinet.

[] Insert 2 self-aligning screws

through outer top cabinet

holes. Turn two full turns on

each screw.

D/

[_ Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

[] Install grease filters. See the Owner's Manual

packed with the microwave.

19

Installation Instructions

RECIRCULATING (Non-Vented Ductless)

INSTALLATION OVERVIEW

C1. Attach Mounting Plate to Wall

C2. Prepare Top Cabinet

C3. Check Blower Plate

C4. Mount the Microwave Oven

C5. Install or change Charcoal Filter

1

IMPORTANT NOTES:

• Make sure the screws for the blower motor and blower _ :----_

plate are securely tightened when they are reinstalled. _ ............... :-:_:,_; _S_°: '_

This will help to prevent excessive vibration. -..... ,_

• Make sure the motor wiring has been properly routed

and secured, and that the wires are not pinched.

ATTACH THE MOUNTING

PLATE TO THE WALL

Attach the plate to the wall using toggle bolts.

At least one wood screw must be used to attach

the plate to a wall stud.

_ Remove the from the bolts.toggle wings

_ nsert the bolts into the mounting plate through

the holes designated to go into drywall and

reattach the toggle wings to 3/4" (19 mm) onto

each bolt.

To use toggle bolts:

Mounting

Plate,

Spacing for Toggles

More Than Wall

÷1_-_.i_,----Thickness

I

i Toggle Wings

,,,t>

Bolt End

_ lace the mounting plate against the wall and

insert the toggle wings into the holes in the wall

to mount the plate.

NOTE: Before tightening toggle bolts and wood

screw, make sure the tabs on the mounting plate

touch the bottom of the cabinet when pushed flush

against the wall and that the plate is properly

centered under the cabinet.

CAUTION: Be careful to avoid pinching fingers

between the back of the mounting plate and the wall.

_ Tighten all bolts. Pull the plate away from the wall

to help tighten the bolts.

I-_ USE TOP CABINET TEMPLATE

FOR PREPARATION OF TOP

CABINET

You need to drill holes for the top support screws and

a hole large enough for the power cord to fit through.

• Read the instructions on the TOP CABINET

TEMPLATE.

• Tape it underneath the top cabinet.

• Drill the holes, following the instructions on the

TOP CABINET TEMPLATE.

CAUTION: Wear safety goggles when drilling holes

in the cabinet bottom.

20

Installation Instructions

CHECK BLOWER PLATE

Blower Plate

• Place the microwave in its upright position, with the

top of the unit facing up.

• Check to see that the blower plate is correctly

installed on the unit.

MOUNT THE MICROWAVE

OVEN

FOR EASIER INSTALLATION AND PERSONAL

SAFETY, WE RECOMMEND THAT TWO PEOPLE

INSTALL THIS MICROWAVE OVEN.

IMPORTANT: Do not grip or use handle

during installation.

NOTE: If your cabinet is metal, use the nylon

grommet around the power cord hole to prevent

cutting of the cord.

NOTE: We recommend using filler blocks if the

cabinet front hangs below the cabinet bottom shelf.

IMPORTANT: If filler blocks are not used,

case damage may occur from overtightening

screws.

NOTE: When mounting the

microwave oven, thread

power cord through hole in

bottom of top cabinet. Keep

it tight throughout Steps

1-3. Do not pinch cord or

lift oven by pulling cord.

[]Lift microwave, tilt

it forward, and hook

slots at back bottom

edge onto four lower

tabs of mounting

plate.

[]Rotate front of oven

up against cabinet

bottom.

[]Insert a self-aligning screw through top center

cabinet hole. Temporarily secure the oven by

turning the screw at least two full turns after the

threads have engaged. (It will be completely

tightened later.) Be sure to keep power cord

tight. Be careful not to pinch the cord, especially

when mounting flush to bottom of cabinet.

Cabinet Front

Cabinet Bottom Shelf

Filler Block

-_Equivalent to Depth

of CabinetRecess

Self-AligningScrew

MicrowaveOvenTop

[]Attach the microwave oven to the top cabinet.

21

Installation Instructions

_-_ M OU NT THE M ICROWAVE

OVEN (cont.)

[]Insert 2 self-aligning screws

through outer top cabinet

holes Turn two full turnson

each screw.

/

,/

[_ Tighten center

screw completely.

[] Tighten the outer two screws to the top of the

microwave oven. (While tightening screws, hold

the microwave oven in place against the wall and

the top cabinet.)

[_ Install grease filters Seethe Owner's Manual

packed with the microwave.

_-_ INSTALLING OR CHANGE

THE CHARCOAL FILTER

NOTE: The charcoal filter isfactory installed in

recirculating models Follow these stepsto replace a

filter or to install a filter after converting a vented

model to recirculating operation.

[_ Remove screwson top of grille using a

#1 Phillips screwdriver.

[] Open the door.

[] Remove the grille.

Pull the grille straight off.

I

[]Install tile charcoal filter': Lay tile filter" on tile back

of the grille with the black mesh face upper.

Tab S Charcoal filter

C_ 0_ ...... _ _ ----;:'_ _ '--;:_ _'_--:_ _

Replace the grille and the screws.

Close the door.

22

Installation Instructions

BEFORE YOU USE YOUR MICROWAVE

Make sure the microwave oven has been

installed according to instructions.

Read the USE & CARE Manual.

I

r_ emove all packing material from the

microwave oven.

r_ Install turntable ring and glass tray in cavity

Plug power cord into a dedicated 15- to 20-amp

electrical outlet.

Ensure proper /_'_

ground exists /

before use

Replace house flJse or turn breaker back on.

I

F_ EEP INSTALLATION INSTRUCTIONS

FOR THE LOCAL INSPECTOR'S

USE.

F_ FILL OUT PRODUCT REGISTRATION CARD

23

NOTE: IT IS VERY IMPORTANT TO

READ AND FOLLOW THE DIRECTIONS

IN THE INSTALLATION INSTRUCTIONS

BEFORE PROCEEDING W{TH THIS

REAR WALL TEMPLATE

Ths Rear Wall Teropl3te ser_e _ poRoa the b0t_rP

_-ounting p_ate and _ locate the ho zaata] exhaust

2 L_ate and _aa at least one slud o_ the le_ o

n_ht4deo thecenterlia_

NOTE:It ,,'_o_ntmu_ ateo:to,,e,,_o0

_re_, _o_nledfirmymasWd_ou_o_ thewe_ht

_ation _r _he supplied _ggle bolts

s DI hoWsmth_markedlocations Wh_r_th_r_i

thatdo n_tne u_wthatud dll 5_8holefor

_OTE:_ONOrNSr_L_THEMOUNTIN_P_T_

ATT_STIME

4 Re_ov_t_e_er-_Wterot- th_ear wal_

5 aeview the In stalla_ion Ins_m_is_ book _r yaur

m allsflo__ua_n

CAUTIONm EX_tAUSTAnA_roRIS POSmONEnOUTSIDE

RECOMMENO_OmMENS_ON._R_S_ L_O_NAIRWILL

30" MINIMUM WIDTH REQUIRED

...................................................,,")i

Locate and mark _oles to align with hole8 in the

mounting plate

IMPORTANT

LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERUNE

MARK THE LOCATION FOR 2 ADDITIONAL EVENLY

SPACED TOGGLE BOLTS IN THE MOUNTING PLATE

AREA

REAR WALL!TEMPLATE

Locate andmark holes to align with _o_esin the

mountingplate

..........

Trim the l eal wall template alollg the dotied HlleI LOCATE AT LEAST ONE STUD ON EITHER SIDE OF

THE CENTERLINE

I MARKTHE LOCATION FOR 2 ADDITIONAL EVENLY

iSPACEDTOGGLE BOLTS INTHE MOUNTING PLATE

iAREA

I

I

I Part NO:3 _69029_2

I

_A

13 3,_"

13 3,_"

!_ 1 ,:............i{

TOP CABINE TEMPLATE

ID. POWER CORD

Part No :3 _6902475

24 Printed in China