Electrolux EIDW5905JS0A User Manual DISHWASHER Manuals And Guides 1108625L
User Manual: Electrolux EIDW5905JS0A EIDW5905JS0A ELECTROLUX DISHWASHER - Manuals and Guides View the owners manual for your ELECTROLUX DISHWASHER #EIDW5905JS0A. Home:Kitchen Appliance Parts:Electrolux Parts:Electrolux DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher NOTE: Put unit on its back being careful not to pinch the Water Drain Hose. Installation Instructions 1. Remove two (2) screws at front of the kickplate assembly using a #2 Phillips screw driver. 2. Tilt and pull forward to remove see figure 1. IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance to open door. 2. Property Damage Plastic Ends of Hoses Flush Do not use the furnished drain hose or a rubber garden hose for the water supply line. Either of these hoses can burst. Flooding may occur and cause property damage. Floor should be flat and free of any obstruction, IMPORTANT: Drain, water, and electrical lines should be roughed-in before going any further. NOTE: It is not necessary to remove the outer door for installation. Printed in U.S.A. 154813801 10/10 Kickplate Assembly Electric Shock Hazard INSTALLER: Leave Installation Instructions with owner. OWNER: Read your dishwasher Use and Care Manual It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher. Read all instructions before installing Outer Top Screws Toeplate For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher. Kickplat_ Figure 1 NOTE: Pull the hose from "End Storage Location" side. See images below to connect the Drain Hose. Failure to follow this warning can result in serious injury. Cabinet Preparation: As a precaution, it is recommended, but not required that the cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/ moisture damage. Drill, Electric • • Driver, Socket s/32",1/4",5/16" Flaring Tool/Tube Cutter (for copper tubing) • • Flashlight Level • • Pipe Joint Compound (for iron pipe plumbing) or Pipe Thread Tape (for sealing threads) Pliers • Safety Glasses • • Saw, Keyhole or l/f, 11/2"to 2" Hole Cutters Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) • Tape, Electrical or Duct • • • Tape, Measuring Wire Stripper or Utility Knife Wrench, Hex-end • Wrenches, 2 Adjustable Review dimensions in Figure 2 to locate dishwasher's water, and electrical connections. 2. All utilities must be routed in shaded area in the Figure 2. IMPORTANT: Disconnect power before starting Observe all local codes and ordinances for electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. , Make sure your location has the correct drain, water, and electrical outlets to make the connections. Do not install unit under a cooktop range. Damage to tub or other components will occur, drain, 34" min. to 35" max.** Electrical, water, and drain lines must be confined to shaded area, installation. NOTE: Your dishwasher comes from factory with built in drain loop. Do not remove this drain loop. 5. Pull electrical cable through hole into installation area. L 6. Be sure water inlet valve is protected from freezing. If valve freezes and ruptures, flooding may occur. ......... Route water supply line into installation area. 2,. Use only the spring clamp that is provided in the accessory kit, place spring clamp over one of the hoses. See Image Below. HoseShipped InsideDishwasher Use if measures IMPORTANT: Incoming hot water temperature should be at least 120°F (49°C). Water pressure should be between 20-90 psi. 34" to 34V_" screw **NOTE: 35" max. height for standard cabinetry cutout. (5/,_,rain. clearance required from unit to underside of c0untert0p.) Parts You Will Need* (NotIncluded) 31/2"min.t0 4//2"max. Clamp 13/4" To install using Top Mount Cabinet Clips: Left 3. Take the plastic side of the drain hose and insert it into the hose that is already attached to the dishwasher make sure hose ends are flush against each other. See image below. 4. Secure the spring clamp 1/8" from large end of black hose to the plastic side that was inserted for best sealing results. See Image Below. Right 497/8" • "Y" Branch Tailpiece and Connector Kit (See Step 4) • Air Gap Kit (See Step 4) 23 3/4" ............._ T All the parts can be found at local hardware, electrical and plumbing supply stores, H0s To Dishwasher 13/4' A Figure 2 Front If required: screw PlasticEnd Of Hose (for copper tubing) Drain Hose Clamp, 1lh" Diameter Brass Elbow, 90 ° with a 3/s"National Pipe Thread Conduit Connector (UL Listed) Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) 34V8" to 35" Take drain Hose out of dishwasher and find the end that has smaller black rubber material. or 2 Pipe wrenches (for iron pipe plumbing) • • • • NOTE: Install Side Mount Brackets before unit is installed into the cabinet. Insert screws into the front holes of the mounting clips only. (See image below) i Use if measures Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Extra hose length is necessary. High-pressure and high-temperature Stainless Flexible hose with a minimum inner diameter of W' may be used. A shut-off valve installed outside dishwasher cabinet is best. Clips. Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up (preferred method) or down as shown in the illustrations below. (Use extreme caution when the clips are in the down position while installing the dishwasher). The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. 9. Stand dishwasher back upright for further installation. Preferred Drain Areas Choose one of the methods of attachment below to secure unit, holes need to be pre-drilled using a #5 drill bit regardless of the option chosen: To install the Side Mounting 4. 8. 2. CAUTION: Use extreme care in mounting the dishwasher as to not scratch, bump or otherwise damage the console or tub. Cut access holes for the Electrical, Water and Drain hoses in the shaded areas as shown in Figure 2. 90° Install the Cabinet Seal Kit (Instructions included in Kit) b. Top Mount Cabinet Clips (to be used when Side Mount is not an available option) 3. 7. 1. a. Side Mount Cabinet Clips (Preferred Method of attachment) 1. Electric Shock Hazard (Not Included) • Locating the Connections Note: Locate the electrical supply and dishwasher's electrical junction box on right underside of unit behind kickplate assembly. See Figure 4. Determine where you will connect to hot water supply. Review Figure 4 and note the location of water inlet valve. Determine where you will connect the drain hose. Tools and Materials Needed for Installation Dishwasher Anchoring Wrap 90 ° elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve. When tightened, elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4. , Do not push down on open door. To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit. EndStorage Location NOTE: Cabinet Seal Kit (Kit # 154662101). This kit provides a seal between the unit and cabinets once installation is complete. (The Installation Instructions are located in the Kit) Locate water inlet valve behind kickplate on bottom left underside of unit.See Figure 4. The valve has a 3/?,NPT female fitting. Remove Plug , Cut Hazard Door NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed. dishwasher. Tip Over Hazard Do not use dishwasher until completely installed. Electrical, water, and drain lines must be confined to shaded areas in Figure 2. Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. --j 22_ ,,-- I ..... r--- / / ," /' Channel in base Doorin90° openposition Water Line (Not Included) Brass Elbow (to be routedthrough (to be routedthrough channelin base) (Not Included) channelin base) Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary. NOTE: Install Top Mount Clips before unit is installed into the cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below) ///////////////////// k¸ ectrical Line Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. 11 *Heightonlyadjustable to34Y4'max.when installed in35"max,standard cabinetry cutout. Power supply/water inletlocation Figure 4 Tighten * DIMENSIONS Figure 3 INSLJ-ATION INST._LLATION DO NOT BLANKET INCLUDE MAY INSULATION- BE COMPRESSED UPON Spring Clamp !I I , , Water Line If levelers need to be removed, make sure that the floor is free of all obstructions. 1. Carefully place dishwasher inside cabinet area such that is centered in opening. Use caution when moving dishwasher to prevent damage to cabinet, dishwasher and floor. 5. Front of door needs to be even with the front of adjoining cabinets. Front levelers should allow 5/16" below underside of countertop to top of console. 6. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water supply at shut-off valve. Route water line to water inlet valve as shown in Figure 4. 2. Check that dishwasher is level from side to side by placing a leve against the top front section of the tub. See Figure 5a. 3. While firmly pulling water supply line into 90 ° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. 4. Turn on water supply and check for leaks. Connections must securely enclosed within junction box with cover installed. Failure to do so, could result in risk of fire, shock or injury. 1. Review Figures 7, 8 and 9 to see the different ways to connect dishwasher to drain system. Choose method that best suits your need. 5. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. 6. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. , Entry Must be Above Trap , Electrical Supply 1. Remove junction box cover and Pull House Wiring into Junction Box. See Figures Below. Cabinet Attach Clip Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. j---q Cabinet Seal Figure 7. Tailpiece Electric Shock Hazard Side Cabinet Seal Check that the dishwasher is level from front to back by taking out the lower rack, place level on the lower rack wheel support at the bottom of the tub. See Figure 5b. 8. Branch 5a Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Sink at Right Sink at Left 2" Drain Hose Hole Adjust levelers up or down until dishwasher is level. Figure Failure to follow this warning could result in death or serious injury. 7 Holes need to be pre-drilled using a #5 drill to secure unit. 9. Screw mounting brackets firmly to cabinet using screws provided The drain hose loop must be at least 32" high f!'om the floor to insure proper drainage. in literature packet. See Image Below. Cut Hazard Leveling Leg Pull wires this Powersupplyw(res storedherefrom factory. Carefullypullthese3 wires throughjunctionb0x, direction through junction box. Junction Box Figure , Water Figure 5c Figure 5d Electrical 6d Line 6a 3. 10. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly until door opens and closes freely. Air Gap , 3. Connect incoming house black lead to dishwasher's black lead, incoming house white lead to dishwasher's white lead and incoming house green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight. Measure height of cabinet opening from underside of countertop to floor. Check chart for height opening and suggested adjustment. Move dishwasher to front of installation area. Loosen the rear leveling legs by turning counterclockwise. to chart for number of turns. Green Wire to Green Wire Refer [] Water and electrical lines are straight out in front of the dishwasher. [] All four leg levelers are positioned properly. [] Cabinet Seals are positioned on the sides and top of the dishwasher. [] Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher. [] Replace Toe and Kickplate. Note: When replacing and Kickplate hand tighten screws. Failure to follow this warning could result in electric shock. check these items: Toe \ Junction Box Junction Box Cover Leg Leveler Adjustment Chart Height of Cabinet Opening White Wire to White Wire BL LWire to Black Wire (Neutral) 0 341/8"(86.7cm) 2 (Hot) Figure 6b 6 34%" (87.6cm) 9 Green Wire Green Wire Black Black Hot ( Wire Wire ) to White White Wire Wire 4. [] Water supply is turned on. If you connect to a sink trap, local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 8. An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). [] Joints are free of leaks. [] Wiring connections to junction box are tight all access panels are secured back in place. [] Replace kickplate. See Figure 1 If you connect to a disposer, the large end of drain hose will fit. Figure 9(a). The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 9(b). [] Drain hose is assembled to Drain Hose Connector. [] All packing materials and consumer literature have been removed from inside unit. Electric Shock Hazard The dishwasher must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. to (Ground) , 345/16"(87.2cm) Water and drain lines have no kinks and move freely behind the dishwasher. Grounding Instructions: Number of Turns to Adjust Levelers 34" (86.4cm) [] (Ground) 3. / Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. to (N, Cut for 5/8" connection. Larger end /of hose / fits" disposer \ 1mO,OV _(_#--_ , Use a UL listed conduit connector (not included) at box to stabilize wiring. , Cut for 3/4" [] Dtatn Make sure that all wire ties are removed from the Adjustable Rack Assembly and Silverware Baskets. Hose / Drain Air Gap Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. Failure to follow these instructions could result in death or serious injury. / i Junction Box / "_"-,<__/ Q i i Junction Cover Box ® II _ i! II ":!'7_ _ __ Wire (Pulled Junction from Nose / thru Box) Drain Figure 6c Replace junction box cover. Figure Disposer 9(b) _ Operate the machine through at least one fill and pump-out, checking the following items: [] On EIDW5905 press and hold down HI-TEMP Icon for 5 - 10 seconds before first use. [] At first fill, approximately 2 minutes, make sure water completely covers filter surface. [] At pump-out: (pump-out is either when the cycle is completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. [] Check water connections again for leaks. Through Floorint _, Plug in 4. Open and close door to make sure it does not hit surrounding cabinet or countertop. Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. i Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may rupture and flooding may occur. [] connection. All wiring connections must be enclosed in the junction box. This unit has copper lead wires. Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur. Dishwasher is level and securely fastened. inletf!tting. -- Figure 9(a) [] Do not connect the dishwasher to the power supply until the appliance is permanently grounded. i Property Damage Do not solder within 6" of the water inlet valve. Damage to the plastic parts in the valve may occur. Failure to follow this warning may result in injury. Line check these items: Figure Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 7. Sink at Right 2" Drain Hose Hole The drain hose loop must be at least 32" high from the floor to insure proper drainage.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Wed Aug 31 04:21:14 2011 Author : Title : Subject :EXIF Metadata provided by EXIF.tools