Electrolux EIDW6105GB0 User Manual DISHWASHER Manuals And Guides L0806005
ELECTROLUX Dishwasher Manual L0806005 ELECTROLUX Dishwasher Owner's Manual, ELECTROLUX Dishwasher installation guides
User Manual: Electrolux EIDW6105GB0 EIDW6105GB0 ELECTROLUX DISHWASHER - Manuals and Guides View the owners manual for your ELECTROLUX DISHWASHER #EIDW6105GB0. Home:Kitchen Appliance Parts:Electrolux Parts:Electrolux DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher NOTE: Put unit on its back being careful not to pinch the Water Drain Hose. Installation Instructions 1. Remove two (2) screws at front of the kickplate assembly using a #2 Phillips screw driver. 2. Tilt and pull forward to remove see figure 1. IMPORTANT: For proper operation and appearance of unit, cabinet opening should have dimensions as shown in Figure 2. If unit is to be placed in a corner, there must be at least a 2-inch side clearance to open door. 2. Property Damage Do not use the furnished drain hose or a rubber garden hose for the water supply line. Either of these hoses can burst. Flooding may occur and cause property damage. Floor should be flat and free of any obstruction. IMPORTANT: Drain, water, and electrical roughed-in before going any further. lines should be NOTE: It is not necessary to remove the outer door for installation. Printed in U.S.A. 154671001 02/08 INSTALLER: Leave Installation Instructionswith lilckplate Assembly Electric Shock Hazard owner. Electrical, water, and drain lines must be confined to shaded areas in Figure 2. OWNER: Read your dishwasher Use and Care Manual. It contains important safety information for operating this appliance. It also has many suggestions for getting the best results from your dishwasher. Outer Door . Electric conductors, water, and drain could be damaged. Failure to follow these instructions could result in fire or electric shock. Measure height of cabinet opening from underside ofcountertop to floor. Check chart for height opening and suggested adjustment. Leg Leveler Adjustment Heightof Cabinet Opening Read all instructions before installing NOTE: If dishwasher is installed at end of a cabinet, sides and back must be fully enclosed. dishwasher. Top Screws Toeplate For your safety, please read and observe all safety instructions. This guide will help you anticipate drain, water, and electrical connections, and help you select the best location for the dishwasher. Kickl: Figure . Do not push down on open door. Failure to follow this warning can result in serious injury. Cut Hazard To prevent serious injury from sharp edges, wear work gloves when handling, unpacking or disassembling unit. ! Locate water inlet valve behind kickplate on bottom left underside of unit.See Figure 4. The valve has a 3/8"NPT female fitting. Remove Plug . Tip Over Hazard Do not use dishwasher until completely installed. NOTE: Cabinet Seal Kit (Kit # 154662101). This kit provides a seal between the unit and cabinets once installation is complete. (The Installation Instructions are located in the Kit) NOTE: Pull the hose from "End Storage Location" side. See images below to connect the Drain Hose. L Wrap 90 ° elbow (not included) with pipe thread tape (or apply joint compound) and thread it into water inlet valve. When tightened, elbow should point toward the left. To prevent bending of bracket or breaking of valve, avoid overtightening. See Figure 4. Cabinet Preparation: As a precaution, it is recommended, but not required that the cabinets enclosing all sides of the dishwasher (including the underside of the countertop) be sealed with an oil based paint or moisture-proof polyurethane to prevent possible steam/ moisture damage. EndStorageLocation 2. Take drain Hose out of dishwasher and find the end that doesn't have the black rubber material. Use only the spring clamp that is provided in the accessory kit, place spring clamp over one of the hoses. See Image Below. Locating the Connections Review dimensions in Figure 2 to locate dishwasher's water, and electrical connections. 2. All utilities must be routed in shaded area in the Figure 2. drain, Tools and Materials Needed for Installation (NotIncluded) Observe all local codes and ordinances for electrical and plumbing connections. All electrical and plumbing work should be performed by qualified persons. Failure to follow this warning could result in death or serious injury. Drill, Electric Driver, Socket 5/s2",1/4",5/16" Flaring Tool / Tube Cutter (for copper tubing) 1. Flashlight Level Pipe Joint Compound (for iron pipe plumbing) or • Pipe Thread Tape (for sealing threads) Pliers • Safety Glasses • • Saw, Keyhole or V2", 11/2"to 2" Hole Cutters Screw Drivers, Slotted and #2 Phillips (magnetic tip preferred) • Tape, Electrical or Duct • • • Tape, Measuring Wire Stripper or Utility Knife Wrench, Hex-end • Wrenches, 2 Adjustable (for copper tubing) or2 Pipe wrenches (foriron pipe plumbing) Parts You Will Need* • • • • Make sure your location has the correct drain, water, and electrical outlets to make the connections. Do not install unit under a cooktop range. Damage to tub or other components will occur. 34" rain. to 35" maxf* 3 I/2"min.to 41/2"max. 34_/2'' (87.6cm) 9 2. Move dishwasher to front of installation area. 3. Loosen the rear leveling legs by turning counterclockwise. to chart for number of turns. Refer Dishwasher Anchoring 4. Install the Cabinet Seal Kit (Instructions included in Kit) 5. Choose one of the methods of attachment below to secure unit, holes need to be pre-drilled using a #5 drill bit regardless of the option chosen: Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up (preferred method) or down as shown in the illustrations below. (Use extreme caution when the clips are in the down position while installing the dishwasher). 3. Cut access holes for the Electrical, Water and Drain hoses in the shaded areas as shown in Figure 2. 4. The dishwasher operates on a 120 volt, 60 Hz electrical supply. Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps (20 amps if connected with disposer) but not more than 20 amps. 5. Pull electrical cable through hole into installation area. 6. Be sure water inlet valve is protected from freezing. If valve freezes and ruptures, flooding may occur. 7. Determine amount of tubing needed to connect hot water supply to the unit's water inlet valve. Extra hose length is necessary. High-pressure and high-temperature Stainless Flexible hosewith a minimum inner diameter of V4"may be used. A shut-off valve installed outside dishwasher cabinet is best. 8. Route water supply line into installation area. NOTE: Install Side Mount Brackets before unit is installed into the cabinet. Insert screws into the front holes of the mounting clips only. (See image below) 3. Take the plastic side of the drain hose and insert it into the hose that is already attached to the dishwasher make sure hose ends are flush against each other. See image below. 4, Secure the spring clamp 1/8" from large end of black hose to the plastic side that was inserted for best sealing results. See Image Below. Plastic Ends of Hoses Flush Use if measures 34V8" to 35" Use if measures 34" to 34V_" IMPORTANT: Incoming hot water temperature should be at least 120°F (49°C). Water pressure should be between 20-90 psi. Hose Attached to Dishwasher **NOTE: 35" max. height for standard cabinetry cutout. (s/,_,min. clearance 13/4" required from unit to - 1a/4" underside of countertop.) Left Depending on the depth of cabinet, the Top Mount Clip have a break off point that can be removed if necessary. Right 497/_ '' • "Y" Branch Tailpieceand Connector Kit (See Step 4) • Air Gap Kit (See Step 4) ",_ 22//'-- NOTE: Install Top Mount Clips before unit is installed into the cabinet. Screw clips firmly to top brace using screws provided in the literature pack. (See image below) i" ,Y / All the parts can be found at local hardware, electrical and plumbing supply stores. 6 To install using Top Mount Cabinet Clips: Front If required: 345he'' (87.2cm) To install the Side Mounting Clips. electrical 9. Stand dishwasher back upright for further installation. Preferred Drain Areas 2 screw (Not Included) Drain Hose Clamp, 1'h" Diameter Brass Elbow, 90 ° with a s/s"National Pipe Thread Conduit Connector (UL Listed) Wire Nuts, three (3) for 12-14 gauge wire (UL Listed) Electrical, water, and drain lines must be confined to shaded area. 34W' (86.7cm) CAUTION: Use extreme care in mounting the dishwasher as to not scratch, bump or otherwise damage the console or tub. junction box on right underside of unit behind kickplate assembly. See Figure 4. Determine where you will connect to hot water supply. Review Figure 4 and note the location of water inlet valve. Determine where you will connect the drain hose. Electric Shock Hazard 0 b. Top Mount Cabinet Clips (to be used when Side Mount is not an available option) Disconnect power before starting installation. Note: Locate the electrical supply and dishwasher's 34" (86.4cm) a. Side Mount Cabinet Clips (Preferred Method of attachment) 1. IMPORTANT: Chart NumberofTurns to Adjust Levelers / Doorin900 openposition Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. Power supply/water inletlocation *DIMENSIONS DO NOT IN CLUED E INSULATION Water Line Brass Elbow (Not Included) (Not Included) Figure LElectrical Line Tighten Spring Clamp 3. 6. If levelersneedtoberemoved, makesurethatthefloorisfreeofall obstructions. 7. Carefullyplacedishwasher insidecabinetareasuchthatis centeredinopening.Usecautionwhenmovingdishwasher to prevent damagetocabinet,dishwasher andfloor. 8. Frontofdoorneedstobeevenwiththefrontofadjoiningcabinets. Frontlevelersshouldallow5/16"belowunderside ofcountertop totopof console. 9. Checkthatdishwasher is levelfromsidetosideby placinga level againstthetopfrontsectionofthetub. SeeFigure5a. Green Wire to Green Wire 4. (Ground) Junction' Box Cover 1 Wire to Black Wire Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. If you connect to a disposer, the large end of drain hose will fit. Figure 9(a). The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose. See Figure 9(b). Failure to follow this warning could result in death or serious injury. Grounding Instructions: 4. The dishwasher must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. White Wire to White Wire (Neutral) (Hot) Figure 6a Figure 5a Electric Shock Hazard Electric Shock Hazard Junction Box _iiii If you connect to a sink trap, local codes may require you to install an air gap kit, (not included). The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 8. An air gap kit is available from a plumbing supply store. (If the drain hose is installed through the floor, an air gap is necessary). Replacejunction Cut for 5/8" Cut Hazard Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. fts disport inlet fitting. Drain Figure Do not connect the dishwasher to the power supply until the appliance is permanently grounded. box cover. Larger end connection. 9(a ) Hose Failure to follow this warning may result in injury. cut for 3/,_ " conn_tion. All wiring connections must be enclosed in the junction box. This unit has copper lead wires. 10. Check that the dishwasher is level from front to back by taking out the lower rack, place level on the lower rack wheel support at the bottom of the tub. See Figure 5b. Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. 11. Adjust levelers up or down until dishwasher is level. Cabinet Attach Drain Air Gap Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. Clip Holes need to be pre-drilled using a #5 drill to secure unit. Failure to follow these instructions serious injury. 12. Screw mounting brackets firmly to cabinet using screws provided If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. ! could result in death or Cabinet Seal in literature packet. See Image Below. - -L Cabinet Seal __[_ Drain Through Floor into _ Separate Trap Sink at Right 1. Figure Figure 5c Review Figures 7, 8 and 9 to see the different ways to connect dishwasher to drain system. Choose method that best suits yourneed. Disposer Figure Leveling Leg , 6. Figure Line 6b Electrical .y. Branch Tailpiece Line _t _t All four leg levelers are positioned properly. _l Cabinet Seals are positioned on the sides and top of the dishwasher. Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur. _l Cabinet Attachment Clips are attached to the cabinet on both corners on top of the dishwasher. Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may rupture and flooding may occur. _l Replace Toe and Kickplate. Note: When replacing and Kickplate hand tighten screws. Water Line 1. 2. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water supply at shut-off valve. Route water line to water inlet valve as shown in Figure 4. 3. While firmly pulling water supply line into 90° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. 4. Turn on water supply and check for leaks. Electrical Supply 1. Remove junction boxcoverand box. See Figures Below. 2. Use a UL listed conduit connector (not included) at box to stabilize wiring. 3. pull housewiring into junction Connect incoming black lead to dishwasher's black lead, incoming white lead to dishwasher's white lead and incoming green lead to dishwasher's green lead with wire nuts. (See Grounding Instruction Warning). Wire nuts must be tight. Sink at Left 2" Drain Hose Hole Figure 7 The drain hose loop must be at least 32" high from the noor to insure proper drainage. Toe . If you connect to a sink drain, entry will need to be above trap. A "Y" branch tailpiece and connector kit, not included, will make this method easier and includes all needed fittings and instructions. See Figure 7. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. 8. Be sure unit does not rest on drain hose. tt should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. Sink at Right Water and electrical lines are straight out in front of the dishwasher. If the cabinet wall is wood, sand edges of hole until smooth and rounded. If cabinet wall is metal, cover all sharp edges with electrical or duct tape to avoid cutting drain hose. 7. check these items: Do not solder within 6" of the water inlet valve. Damage to the plastic parts in the valve may occur. 9(b) Entry Must be Water Property Damage 2" Drain Hose Hole The drain hose loop must he at least 32" high from the floor to insureproper drainage. 5d 13. Open and close dishwasher door slowly. Ensure that there is clearance to the console. Adjust accordingly until door opens and closes freely. Electric Shock Hazard Sink at Left Failure to follow this warning could result in electric shock. check these #ems: _t Water and drain lines have no kinks and move freely behind the dishwasher. _t Water supply is turned on. _l Joints are free of leaks. _t Wiring connections to junction box are tight all access panels are secured back in place. _t Replace kickplate. See Figure 1 _l Drain hose is assembled to Drain Hose Connector. _t All packing materials and consumer literature have been removed from inside unit. _t _t Dishwasher is level and securely fastened. Open and close door to make sure it does not hit surrounding cabinet or countertop. Make sure that all wire ties are removed from the Adjustable Rack Assembly, Versa Tray, Utility Tray and Silverware Baskets. _l Operate the machine through at least one fill and pump-out, checking the following items: _t On EWDW6505 press and hold SET Icon for 5 seconds before first use. On EIDW6305 and EIDW6105 press and hold down HI-TEMP Icon for 5 seconds before first use. _l At first fill, approximately 2 minutes make sure water completely covers filter surface. _l At pump-out: (pump-out is either when the cycle is completed or canceled, refer to the Use and Care Manual for Start/Cancel), make sure all water is pumped out. _l Check water connections again for leaks.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Mon Jun 30 04:37:16 2008 Author : Title : Subject :EXIF Metadata provided by EXIF.tools