Electrolux EIDW6405HT0 User Manual DISHWASHER Manuals And Guides 1104515L
User Manual: Electrolux EIDW6405HT0 EIDW6405HT0 ELECTROLUX DISHWASHER - Manuals and Guides View the owners manual for your ELECTROLUX DISHWASHER #EIDW6405HT0. Home:Kitchen Appliance Parts:Electrolux Parts:Electrolux DISHWASHER Manual
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Dishwasher
!
_
Property
Installation
Instructions
NOTE: Put unit on its back
Drain Hose.
Prnted
n
US A
being
careful
not to pinch
i_4u#:% h3_#et
1.
Remove two (2) screws at front of the kickplate
#2 Phillips screw driver.
2,
Tilt and pull forward to remove
assembly
using a
"!d +
2 Pilot d_ill hc_eo*
10/10
Leave
Installation
Instructionswith
owner.
*-
OWNER: Read your dishwasher
Use and Care Guide
It contains
important safety information for operating this appNance, n also has
many suggestions for getting the best resuns from your dishwasher.
i_suarl_ _L_
Figm"e3
_YBECOMPaESSEO
UPO_
all
instructions
before
installing
2,
dishwasher.
For your safety, please read and observe an safety
instructions.
This guide will help you anticipate drain, water, and
electrical connections, and help you select the best location for the
dishwasher.
Tip Over Hazard
Do not use dishwasher
until completely
Do not push
Failure
injury.
down
to follow
on open
%- 6 Pilot drill fiole_
can result
Tools and Materials Needed for
Included)
Electric
Figure
NOTE:
,-t _ _embly
3.
Locate water inlet valve behind kickplate on bottom left underside
of unibSee Fig ure 4. The valve has a 3/8"NPT female rifting.
Remove Plug
4.
Wrap 90° elbow (not included) with pipe thread tape (or apply
joint compound) and thread it into water inlet valve. When
tightened, elbow should point toward the lee. To prevent bending
of bracket or breaking of valve, avoid overlightening.
See Figure 4.
NOTE:
back
If dishwasher
must
is installed
at end of a cabinet,
sides
NOTE: Cabinet Seal Kit (Kit # 154662101).
This kit provides
a
seal between the unit and cabinets
once installation
is
complete.
(The Installation
Instructions
are located in the Kit)
As a precaution,
it is recommended,
but not required
that the
cabinets
enclosing
all sides of the dishwasher
(including
the
underside
of the countertop)
be sealed with an oil based paint
or moisture-proof
polyurethane
to prevent possible
steamf
moisture
damage.
!
i
,"
_
electrical
and plumbing connections,
All electrical
and plumbing
work should be performed
by
q ua6fled persons.
Failure to follow this warning
could result in death or serious
injury.
Wire Stripper or Utility Knife
Wrench, Hex-end
1.
Make sure your location has the correct drain, water, and
electrical outlets to make the connections.
Do not instafl unit
under a cooklop range. Damage to tub or other components
will
occur.
You Will Need* (NotIncluded)
Drain Hose Clamp, 1eg Diameter
Brass Elbow, 90' with a 3/d' National Pipe Thread
Conduit Connector (UL Listed)
Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)
To prevent the posssibi6ty of corrosion,
supplied screws for mounting
the wood
The custom
Items
panel should
use factory
panel,
provided
be 1/2 to 3/4" (19mm)
in Figure 2 to locate
connections.
must be routed
Disconnect
Pull the hose from "End Storage Location" side.
See images below to connect the Drain Hose.
l.
Take drain Hose out of dishwasher and find the end that
doesn't have the black rubbe r material.
2.
Use only the spring clamp that is provided in the accessory
kit, place spring clamp over one of the hoses. See Image
Below.
dishwasher's
in shaded area in the
power
before
starting
drain,
Figure
Six 1_/8"screws
dishwasher.
for moun0ng
THE CUSTOM
the custom wooden
2.
installation.
3.
CutaccesshoiesfortheEiectdcaI,
shaded areas as shown in Figure
4.
The dishwasher operates on a 120 volt, 60 Hz electrical supply.
Provide a separate circuit with a fuse or circuit breaker rated for
at least 15 amps (20 amps if connected with disposer) but not
more than 20 amps.
5.
PUll electrical
6.
Be sure water inlet valve is protected from freezing.
freezes and ruptures, flooding may occur.
7.
Determine amot.mt of tubing needed to connect hot water supply
to the uniPs water inlet valve. Extra hose length is necessary.
High-pressure and high-temperature
Stainless Flexible hose with
a minimum inner diameter of '/g' may be used. A shut-off valve
inWalled outside
dishwasher cabinet is best.
8,
Route water supply line intoinstalia6on
cable through
3.
4.
Take the plastic side of the drain hose and insert it into the
hose that is already attached to the dishwasher make sure
hose ends are flush against each other. See image below.
Secure the spring clamp 1/8" from large end of black hose to
the plastic side that was inserted
See Image Below.
area.
Plastic
Ends
of Hoses
Flush
area.
back updght for further
• Air Gap Kit (See Step 4)
electrical
instaliaOon.
temperature
should
should be between
be at
Hose
Attached
before the unit is mounted
references.
2. The two short screws (see Installation Tips, Parts you will
need) go into the back of the panel 14W3_" from the upper
edge of the panel and _/_" from the edge of the panel. Insert
the short screws into the panel, leaving V_" of space between
the screw head and the panel.
and
3. Hook the panel screws into the rectangular
metal panel on the dishwasher door.
k4
Figllre 2
4. Open the door and use the six screws
panel to the door.
NOTE: The door
panel cannot
exceed
openings
supplied
of the
Tighten
to secure the
(Not Included)
12 pounds.
Fig.re
5
Brass Elbow
(Not Included)
Electrical Line
for best sealing
If valve
1. Fit the handle onto the panel according to the manufacturer's
instructions. (NOTE: A handle should be used rather than a
knob. A knob does not provide enough grip.)
Tailpiece and
Kit (See Step 4)
Shipped
Dishwasher
WaterandDrainhosesintbe
2,
hole into installation
IMPORTANT:
Incoming
hot water
least 120°F (49°C). Water pressure
20-90 psi,
Hose
Inside
PANEL
be installed
Refer to the Figure 4 for instruction
panel to the
Hose Attached
To Dishwasher
Locate the electrical supply and dishwasher's
electrical
junction box on right underside of unit behind kickplate
assembly. See Figure 5. Determine where you will connect
to hot water supply. Review Figure 5 and note the location of
water inlet valve. Determine where you will connect the drain
hose.
9. Stand dishwasher
thick.
with the unit:
A custom door panel should
to the cabinet.
If required:
All the parts can be found at local hardware,
plumblng supply stores.
All utilities
The EIDW6405HT
can be installed with a fully integrated, buyer
supplied custom door panel.
INSTALLING
• 2 # 7 V2" screws (optional)
• "Y"Branch
Connector
2,
k
so
the Connections
Review dimensions
water, and electrical
Screws
Tape, Electrical or Duct
Tape, Measuring
•
•
•
•
Locating
1.
Note:
Safety Glasses
Parts
SPRINGS
and
IMPORTANT:
Saw, Keyhole or V2", 1V2" to 2" Hole Cutters
Screw Drivers, Slotted and #2 Phillips (magnetic6p
preferred)
Location
be fully enclosed.
Preoaration:
or
(for iron pipe plumbing)
DOOR
1
Flashlight
Level
or 2 Pipe wrenches
THE
Before you push the dishwasher into the cabinet opening, test
the door to make sure it stays in place at any angle.
If it tends
to fall down, pull out the machine and adjust the tension of the
door springs on the sides of the machine by moving them one
hole farther back.
Weight
Keep children away from the front of the dishwasher
that they are not accidentany
hit by the door during
loading or unloading
or if door should unexpectedly
open. The weight of the door can cause injury.
Ddll Bit Vs"
# 32 Drill Bit (V_") (optional)
Wrenches, 2AdjuWable
(for copper tubing)
End Storage
4
ADJUSTING
Ddver, Socket 5/32", '/4" ,5/,"
Flaring Tool / Tube Cutter (for copper tubing)
Pipe Joint Compound (for iron pipe plumbing)
Pipe Thread Tape (forseaNng threads)
Pliers
ltssh!feoes_,elf
belowp3nel
sg#lce L_ll_'/e
i_tir_/uded,)
Toeplate
Cabinet
•
Figure
Kickplat6
Kickplale
in serious
llot_: f_l h_odb
efteeh r{leot
_efeveT,fetlll_ be
be
installed.
Cut Hazard
Ddll,
should
door.
this warning
(Not
lines
_-_I
{ %" dim a ¾" r3e;c de_,th)
*0pfleoelholesfor eddie§1/2"- #7sore_s
whichslipinto recta%olaf@eningoof
me_31panel
to help 17ocate
oostomdoor
pa#elfc_e#lerouts{descrew31techrneo_
be flat and free of any obstruction.
IMPORTANT:
Drain, water, and electrical
roughed-in
before going any further.
To prevent serious injury from sharp edges, wear work
gloves when handling,
unpacking
or disassembling
unit,
Installation
FIoor should
-/_1
(Vd' alia,_ _A" ma:_+de_th)
23 %,_"
_|
IMPORTANT:
For proper operation
and appearance
of unit,
cabinet opening should have dimensions
as shown in Figure 2,
If unit is to be placed in a corner, there must be at least a 2-inch
side clearance to open door.
Read
114_:'/_" /
see figure 1.
154747401
INSTALLER:
Do not use the furnished
drain hose or a rubber garden hose
for the water su pply line, Either of these hoses can burst,
Flooding may occur and cause property
damage.
WeigN: 12 Ibs. el_x,
the Water
O k
Damage
Spring Clamp
resuns.
6,
If levelers need to be removed,
obstr_lcfions.
make sure that the floor is free of all
7.
Care fully place dishwasher inside cabinet area such that is
centered in opening. Use caution when moving dishwasher to
prevent damage to cabinet, dishwasher and floor.
8.
Front of door needs to be even with the front of adjoining cabinets.
Front levelers ShOLddallow 5/16" below underside of countertop
to top of console.
9. Check that dishwasher is level from side to side by placing
against the top front section of the tub. See Figure 6a.
5.
1.
Review Figures 8, 9 and 10 to see the different ways to connect
dishwasher to drain system. Choose method that best suits
yourneed.
a level
White
Measure height of cabinetopening
countertop tofloor. Check chartfor
suggested adjustment.
Leg Leveler
from underside of
height opening and
Junction
Box Cover
Figm'e
Adjustment
Wire
to Black Wire
7a
Number of Tumsto
Adjust Levelers
34"(86.4cm)
0
34 _8"(86.7cm)
2
10. Check that the dishwasher is level from front to back by taking
out the lower rack, place level on the lower rack wheel support at
the bottom of the tub. See Figure 6b.
34 _"
6
11. Adjust levelers
(87.2cm)
34_z"(87.6cm)
Wire
Electric
Holes
2,
Move dishwasher
3.
Loosen the rear ]evefing legs by turning counterclockwise.
to chart for number of turns.
area.
Lip or down until dishwasher
need to be pre-drified
12. Screw mounting
Refer
Jf
Sink ,t L_#
is level.
in literature
using a #5 drill to secure
brackets firmly to cabinet
packet.
See Image
Anchoring
4.
instal] the Cabinet
Seal Kit (Instn.lctions
5.
Choose one of the methods of attachment below to secure unib
holes need to be pre-ddlled using a #5 ddll bit regardless of
the option chosen:
included
Clips (Preferred
unit.
F_.re
Below.
at R_h,
Failure to follow
death or serious
as to
or tub.
Clips,
clips only. (See image
Figztre
6c
Figttre
result
in
32" high
[rom the [Ioor
If you connect to a sink drain, entry will need to be above trap.
A "Y" branch tailpiece and connector kit, not included, will make
this method easier and includes all needed fillings and
instructions.
See Figure 8.
Failure
to
follow
this
warning
may
result
in
injury.
13. Open and close dishwasher door slowly. Ensure that there is
clearance to the console. Adjust accordingly unfil door opens
and closes freely.
check
Figure
these items:
71)
check
Water and drain lines have no kinks and move freely
behindthe dishwasher.
these items:
Water
Water and electrical
dishwasher.
below)
341/_ '' to
could
6d
lines are straight out in front of the
are positioned
Cabinet Seals are positioned
dishwasher.
35"
Property Damage
Do not solder within 6" of the water inlet valve. Damage
the plastic parts in the valve may occur.
Use care that no sealer, dirt, or other objects
Damage to the filter screen may occur.
to
properly.
on the sides and top of the
Cabinet Attachment Clips are attached to the cabinet
both comers on top of the dishwasher.
on
Replace Toe and Kickplate. Note: When
and Kickplate
hand tighten screws.
Toe
replacing
supply is turned on.
Joints are free of leaks.
3.
All four leg levelers
{f measures
this warning
injury.
8
The drain hose h)op mu_t be at least
to insuraproper
draimtga,
Depending on space allowed in cabinet the Side Mounting
Clips can be installed with the holes for the screw Lip (preferred
method) or down as shown in the illustrations below. (Use extreme
caution when the dips are in the down position while installing
the dishwasher).
NOTE: Install Side Mount Brackets before unit is installed
into
the cabinet. Insert screws intothe front holes of the
Use
Sink
box
Method of
CAUTION:
Use extreme care in mounting
the dishwasher
not scratch, bump or otherwise
damage the console
mounting
Hazard
using screws provided
in Kit)
b. Top Mount Cabinet Clips (to be used when Side Mount
is not an available option)
the Side Mounting
Shock
Disconnect
electrical
power at the fuse
or circuit breaker
box before beginning
installation.
2,
Dishwasher
To install
be free of
(Hot)
9
to front of installation
I_should
Chart
Heightof
Cabinet Opening
a. Side Mount Cabinet
attachment)
Secure drain hose to sink drain, disposer, or separate trap with a
clamp. IMPORTANT:
Be careful not to overtighten clamp or
you may damage end of hose. Do not connect hose to
horizontal pipe between sink drain and disposer.
electrical components
and door spnngs. Do not cut corrugated
drain hose. PLdl excess through cabinet and place under sink.
Make sure hose does not come in contact with any sharp edges.
Wire
to White
(Neutral)
Move unit back in place while routing drain hose through access
hole. Use caution to prevent damage to the dishwasher, floor and
cabinets. IMPORTANT:
Make sure there are no sharp bends
or kinks that might restrict drain flow.
Be sure unit does not rest on drain hose.
Box
1.
[fthe cabinet wall is wood, sand edges of hole until smooth and
rounded. If cabinet wall is metal, cover all sharp edges with
eleclrical or duct tape to avoid cutting drain hose.
4.
enter the valve.
If you connect to a sink trap, local codes may require you to
install an air gap kit, (not included). The drain hose will be routed
from dishwasher to air gap inlet as shown in Fig ure 9. An air
gap kit is available from a plumbing supply store. (If the drain
hose is installed through the floor, an air gap is necessary).
Wiring connections
panels are secured
to junction box are tight all access
back in place.
Replace
See Figure
If you connect to a disposer,
the large end of drain hose will fit.
Fig ure 10(a). The knock out plug must be removed from
inside disposer
inlet before making
the final fit to drain
hose See Figure 10(b).
All packing materials and consumer
been removed from inside unit.
Be sure the dishwasher
is placed where the water inlet
valve will be kept from freezing.
If the valve freezes, it may
rupture and flooding
may occur.
kickplate.
Drain hose is assembled
Dishwasher
1
to Drain Hose Connector.
is level and securely
literature
have
fastened.
Open and dose door to make sure it does not hit
surrounding cabinet or countertop.
Make sure that all wire ties are removed from the Adjustable
Rack Assembly, Versa Tray, Utility Tray and Silverware
Baskets.
Use if measu,_s 34" to 34V_"
Water Line
1,
2.
TO install using Top Mou nt Cabinet Clips: Depending on the
depth of cabineb the Top Mount Clip have a break off point
that can be removed if necessary.
NOTE: Install Top Mount Clips before unit is installed
into
the cabinet.
Screw clips flrrnly to top brace using screws
provided
in the literature
pack. (See image below)
FlUsh water line before connecting it towater inlet valve to
prevent early clogging of filter screen. Place a bunched towel
over end of line to prevent splashing. Open water supply valve for
a few seconds and let water drain into a pan. Turn off water
supply at shut-off valve.
Rot.de water line to water inlet valve as shown in Figure 5.
3.
While firmly pulling water supply line into 90 ° elbow, tightly
connect water supply to water inlel valve. Supply line must be
free of kinks, scales, chips, and lubricants.
4.
Turn on water supply and check for leaks.
Electrical
Supply
Remove junction
box. See Figure
2,
Use a UL listed conduit
stabilize wiring.
3.
Connect incoming black lead to dishwasher's
black lead,
incoming white lead to dishwasher's
white lead and incoming
green lead to dishwasher's
green lead with wire nuts. (See
Grounding
Instruction Warning).
Wire nuts must be tight.
4.
Replace junction
box cover and pui] house widng into junction
7a.
box cover.
Grounding
Shock
Figttre
Hazard
(not included)
at box to
/
Cuth_t 3/4"_,mne_tion,
lOpO
Instructions:
The dishwasher
must be connected
to a grounded
metal,
permanent
wiring system or an equipment-grounding
conductor
must be run with the circuit conductors
and
connected
to the appliance's
equipment
grounding
terminal
or lead. ]t is the consumer's
responsibility
to contact
a
qualified
installer to make sure the electrical
installation
conforms
with the National
Electrical
Code and local codes
and ordinances.
Do not connect the dishwasher
to the power supply
until the
appliance
is permanently
grounded.
All wiring connections
must be enclosed in the junction
box.
This unit has copper lead wires.
1.
connector
Electric
Sink at Le#
_
"_a_a_tit
On EIDW6405HT
press and hold SANITIZE
seconds before first use.
C
_\
' "
_D
Failure
serious
to follow
injury.
these
instructions
could
"
At first fill, approximately
2 minLdes, make
completely covers filter surface.
keypad
for 8
sure water
At pump-ouh (pump_ut
is either when the cycle is
completed or canceled, refer to the Use and Care Guide
for Stad/Cancel),
make sure all water is pumped ouk
Joining
aluminum
building
wire to stranded
copper wire
should be done by a qualified
electrician
using materials
recognized
by UL and local codes.
Do not use an extension
cord. Such use can result
electrical
shock, or other personal
injury.
Gap
Operate the machine
through at
least one fill and pump-out,
checking the following items:
Check water connections
in fire,
res ult in death or
109(b)
The drain hose
to insm'e proper
h)op mu_t be at h,a_t 32"
_'ainag_
high [rom
the [loor
again for leaks.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Fri May 06 04:13:52 2011 Author : Title : Subject :EXIF Metadata provided by EXIF.tools