Electronic Solutions DBMZ01 Zwave based Motor Controller User Manual RP60ABMH v3 1 Programming Quick Reference

Electronic Solutions, Inc. Zwave based Motor Controller RP60ABMH v3 1 Programming Quick Reference

User Manual

Download: Electronic Solutions DBMZ01 Zwave based Motor Controller User Manual RP60ABMH v3 1 Programming Quick Reference
Mirror Download [FCC.gov]Electronic Solutions DBMZ01 Zwave based Motor Controller User Manual RP60ABMH v3 1 Programming Quick Reference
Document ID870937
Application IDii8Mhdz9z3tyREqqENa/RQ==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize7.74kB (96749 bits)
Date Submitted2007-11-21 00:00:00
Date Available2007-11-21 00:00:00
Creation Date2007-10-24 20:14:18
Producing SoftwareMicrosoft® Office Word 2007
Document Lastmod2007-11-21 11:15:51
Document TitleRP60ABMH v3.1 Programming Quick Reference
Document CreatorMicrosoft® Office Word 2007
Document Author: Bill Gates & David Elrod

DBMZ Version 1+1
Quick Setup
Electronic
Solutions, Inc.
The DBMZ motor controller is compatible with other Z-wave™ enabled devices. After connecting the unit
according to the DBMZ V1+1 Specifications & Installation Instructions, the DBMZ controller will operate
manually using the OPEN and CLOSE buttons on the side of the case. After confirming manual operation,
please note the following:



Mechanical motor limits must be set before performing the calibration sequences below.
If the Motor LED is red, the unit requires calibration in order to operate correctly.
Verify OPEN button opens shade and CLOSE button closes shade. If directions are swapped, see
“Reverse Direction” below.
Calibration Procedure
1. Simultaneously press and hold both OPEN and CLOSE for at least 10 seconds until Motor LED turns
solid green.
2. Release both OPEN and CLOSE.
3. Within 10 seconds press and release CLOSE to start the calibration sequence. (Press and release
OPEN instead to place DBMZ orientation into the “Reverse Direction” and start the calibration
sequence.)
The calibration sequence will run the motor from one limit to the other and end with the shade closed,
motor off, and Motor LED off.
Unit is ready for use.
DC motors with brushes produce significant interference due to noise from arcing at the
brushes. This reduces the effective range for RF controllers.
Note:
Z-Wave Network Include/Exclude
To utilize the DBMZ in a Z-Wave network requires the “Include” process. For INCLUDE, place the primary
controller into the INCLUDE mode and do a quick press of the LEARN button on the side of the DBMZ unit
(Z-Wave STATUS LED will flash green). For “Exclusion”, place the primary controller into the EXCLUDE
mode and do a quick press of the LEARN button (Z-Wave STATUS LED will flash green). Warning: Always
EXCLUDE the DBMZ motor controller before disconnecting it from the Z-Wave network.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by Electronic Solutions, Inc. could void the user's authority to operate the
equipment.
24 October 2007
Rev. A
©2007, Electronic Solutions, Inc.
1355 Horizon Avenue, Lafayette, CO 80026-9304 USA
voice: +1.303.469.9322 fax: +1.303.469.5129 www.elec-solutions.com
page 1 of 1

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
Page Count                      : 1
Language                        : en-US
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:0b2902b3-9594-4ac3-8510-7845364c35c1
Producer                        : Microsoft® Office Word 2007
Modify Date                     : 2007:11:21 11:15:51-08:00
Create Date                     : 2007:10:24 20:14:18Z
Creator Tool                    : Microsoft® Office Word 2007
Metadata Date                   : 2007:11:21 11:15:51-08:00
Document ID                     : uuid:dde707db-2727-45e2-add4-502ab2db4688
Format                          : application/pdf
Title                           : RP60ABMH v3.1 Programming Quick Reference
Creator                         : Bill Gates & David Elrod
Tagged PDF                      : Yes
Author                          : Bill Gates & David Elrod
Keywords                        : Quick, Setup
EXIF Metadata provided by EXIF.tools
FCC ID Filing: P7RDBMZ01

Navigation menu