Electronic Systems Technology ESTEEM195ED Wireless LAN transceiver User Manual 195Ed Chapter 0 Front Cover 195Ed
Electronic Systems Technology Wireless LAN transceiver 195Ed Chapter 0 Front Cover 195Ed
Contents
- 1. Manual Part 1
- 2. Manual Part 2
- 3. Manual Part 3
Manual Part 3
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 985916 |
| Application ID | mtEmLM/sjT6R7SwzHxPXiQ== |
| Document Description | Manual Part 3 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 264.05kB (3300631 bits) |
| Date Submitted | 2008-08-15 00:00:00 |
| Date Available | 2008-08-15 00:00:00 |
| Creation Date | 2008-08-15 15:34:19 |
| Producing Software | GPL Ghostscript 8.61 |
| Document Lastmod | 2008-08-15 15:34:27 |
| Document Title | 195Ed Chapter 0 - Front Cover 195Ed |
| Document Creator | PDFCreator Version 0.9.5 |
| Document Author: | Marske |
CHAPTER 8 ANTENNA SETUPS ASSEMBLING THE AA195PM TWO HOLE OUTDOOR POLE MOUNTING KIT The AA195PM mounting kit contains everything required for pole mounting and weatherproofing the ESTeem Model 195E for outdoor installations. The 195E with AA195PM mounting kit can be directly mounted to a round pole from 1.25” to a diameter of 2.25” OD. Any mounting structure greater than 2” requires hose clamp strapping run through the Pole Mount Brackets. The mounting kit requires the following assembly: 1. 2. Figure 1: Packet Box Contents If you purchased an AA195PM mounting kit with your Model 195E, the kit will be packed in the same packing box as the ESTeem (Figure 1). Remove and inventory the two (2) Pole Mounting Brackets, one (1) Two-Hole Face Plate Cover (with single port cover installed), one (1) Heat Shield and (1) AA195PM Hardware bag from the packing box (Figure 1). Report any missing or damaged items to ESTeem Customer Support (509-735-9092 Phone) as soon as possible for replacement. (2) Square Bend U-Bolts with Hardware (2) Pole Mount Clamps (4) 10-24 Pan Screws (1) Weather Proof Boot for Antenna Port B (if not used) (2) Ethernet Cable Boot Revised: 11 Aug 08 8-3 (2) Direct Mount Antenna Boots for ESTeem Approved Direct Mount Antenna Only Figure 2: AA195PM Hardware Contents EST P/N AA107D CHAPTER 8 ANTENNA SETUPS 3. Inventory the AA195PM Hardware bag for all the components listed in Figure 2. 4. Assemble the two Pole Mounting Brackets with the included U-bolts, hardware and Pole Mount Clamps. Reference Figure 3. Figure 3: Pole Mount Assembly 5. Place the four supplied 10-24 x 1” Phillips Pan Head screws through the mounting holes of the Heat Shield and attach to the to the top of the ESTeem 195E (Figure 4). Figure 4: Heat Shield Attachment Revised: 11 Aug 08 8-4 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS 6. Attach the two Pole Mounting Brackets to the ESTeem Model 195E with the 10-24 x 1” Phillips Pan Head screws through the Figure 5: Pole Mount Connection to Case (Heat Shield Removed for Detail) top of the heat shield. Reference Figure 5 (Heat Shield removed for detail). 7. Assemble the outdoor rated CAT-5e Ethernet cable (Not Provided) with the supplied Ethernet Cable Boot (Figure 6). Ethernet Cable Boot Figure 6: Ethernet Cable Assembly 8. Feed the CAT-5e Ethernet connector(s) through the Face Plate Cover and secure the Ethernet Cable Boot to the cover. Reference Figure 7. NOTE: The Ethernet cable boot must be installed before the RJ-45 end is installed. If using the ESTeem AA09.1 outdoor Ethernet cable, verify that the Ethernet cable boot end is routed toward the ESTeem 195E. Revised: 11 Aug 08 8-5 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS Second Port Cover Remove for 2nd Cable Face Plate Cover Ethernet Cable Boots 9. Figure 7: Ethernet Cable Routing Route the CAT-5e Ethernet cable through the molded strain-relief fins in the Face Plate Cover (Figure 8) to secure the cable and provide strain-relief for the connector. If a second Ethernet cable is installed, remove the second port cover and route cable. Figure 8: Face Plate Cover Strain Relief 10. Plug the CAT-5e Ethernet cable to the Model 195E’s Ethernet port and secure the Face Plate Cover with the attached thumb screw. Verify that the weatherproof seal on the Face Plate Cover is sealed against the outer rim of the Model 195E. Reference Figure 9. Figure 9: Face Plate Cover Installed on ESTeem 11. Attach the antenna connector boots as show in Figure 10 for either dual attached antennas or external antennas. You are now ready to mount the ESTeem Model 195E Revised: 11 Aug 08 8-6 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS EST Approved Direct Mount Antenna Only EST Approved External Antenna With Factory Installed Boot Direct Mount Antenna Boots Port A Port B Weather Proof Boot NOTE: Remove Plastic Connector Cover Before Installation Face Towards The South (North America) Figure 10: Completed AA195PM Mounts Caution: Outdoor mounting of the 195E requires the use of weatherproof boots. Improper installation could result in radio failure. Caution: Always mount the 195E vertically with the antenna ports on top. Revised: 11 Aug 08 8-7 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS Model 195Ed with Direct Mount Antenna and Surge Protection Omni-Directional Antenna EST P/N AA20DMEs Antenna Port A Weatherproof Boot Direct Pole Mount Pole Mounting Kit EST P/N AA195PM Pole Mounting Brackets (not shown) Weatherproof Front Cover RS-232 ESTeem Resources Programming EST Part No. AA109 Interface Cable Weatherproof Boot EST Part No. AA0621.1 RS-232C Serial Interface Cable RS-232, RJ-45/DB9F EST P/N AA0621.1 Serial Interface Cable EST P/N AA09.1 ft. maximum) (50 Ethernet Surge Protection POE Cable EST P/N AA166 EST P/N AA09.1 (300 ft. maximum) POE Supply EST P/N Ethernet LAN AA175 Interface Cable 100-250 VAC 50-60 Hz Earth Ground In Building Caution: Always mount the 195Ed vertically with the antenna ports on top. Revised: 11 Aug 08 8-8 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS Caution: Always mount the 195Ed vertically with the antenna ports on top. Revised: 11 Aug 08 8-9 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS Caution: Always mount the 195Ed vertically with the antenna ports on top. Revised: 11 Aug 08 8-10 EST P/N AA107D CHAPTER 8 ANTENNA SETUPS FRESNEL ZONE The Fresnel zone shows the ellipsoid spread of the radio waves around the visual line-of-sight after they leave the antenna (see figure above). This area must be clear of obstructions or the signal strength will be reduced due to signal blockage. Typically, 20% Fresnel Zone blockage introduces little signal loss to the link. Beyond 40% blockage, signal loss will become significant. This calculation is based on a flat earth. It does not take into account the curvature of the earth. It is recommended for RF path links greater than 7 miles to have a microwave path analysis done that takes the curvature of the earth and the topography of the terrain into account. Fresnel Zone Radius = 72.1 SQRT [(d1d2) / (F(d1 + d2)] Units Fresnel Zone Radius in feet. d1 and d2 in statue miles F in GHz Revised: 11 Aug 08 8-11 EST P/N AA107D APPENDIX A FCC-DOC INFORMATION INFORMATION TO USERS Other Information The ESTeem Model 195Ed complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Model 195Ed Direct Sequence/OFDM Spread Spectrum Device (USA) FCC ID: ENPESTEEM195ED (Canada) IC No: 1457-195ED This Class A digital apparatus complies with Canadian ICES-003. (Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.) Note to User: Changes or modifications to this equipment not expressly approved by Electronic Systems Technology for compliance could void the user's authority to operate the equipment. The equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Revised: 11 Aug 08 APX A-1 EST P/N AA107D APPENDIX A FCC-DOC INFORMATION FEDERAL COMMUNICATIONS COMMISSION FIELD OFFICES ALASKA 1011 E. Tudor Rd. Rm 240 Box 2955 Anchorage, AK 99510 CALIFORNIA Interstate Office Park 4542 Ruffner St., Room 370 San Diego, CA 92111-2216 Los Angeles Office (LA) Ceritos Corporate Tower 18000 Studebaker Rd., Room 660 Cerritos, CA 90701-3684 San Francisco Office (SF) 5653 Stoneridge Drive, Suite 105 Pleasanton, CA 94588-8543 COLORADO Denver Office (DV) 215 S. Wadsworth Blvd., Suite 303 Lakewood, CO 80226-1544 FLORIDA 919 Federal Bldg 51 SE First Ave. Miami, FL 33130 Tampa Office (TP) 2203 N. Lois Ave., Room 1215 Tampa, FL 33607-2356 ILLINOIS Chicago Office (CG) Park Ridge Office Ctr., Room 306 1550 Northwest Highway Park Ridge, IL 60068-1460 LOUISIANA New Orleans Office (OR) 2424 Edenborn Ave. Suite 460 Metarie, LA 70001 OREGON 1782 Federal Building 1220 SW 3rd Avenue Portland, OR 97204 MARYLAND 1017 Geo. Fallon Building 31 Hopkins Plaza Baltimore, MD PENNSYLVANIA Philadelphia Office (PA) One Oxford Valley Office Bld. Room 404 2300 E. Lincoln Hwy Langhorne, PA 19047-1859 MASSACHUSETTS Boston Office (BS) 1 Batterymarch Park Quincy, MA 02169-7495 PUERTO RICO 747 Federal Building Carlo Chardon Ave. Hato Rey, PR 00918 MICHIGAN Detroit Office (DT) 24897 Hathaway Street Farmington Hills, MI 48335-1552 TEXAS Dallas Office (DL) 9330 LBJ Freeway, Room 1170 Dallas, TX 75243-3429 MINNESOTA 691 Federal Building 316 N Robert St. St. Paul, MN 5636 Federal Building 515 Rusk Avenue Houston, TX 77002 GEORGIA Atlanta Office (AT) 3575 Koger Blvd., Suite 320 Duluth, GA 30096-4958 MISSOURI Kansas City Office (KC) 520 NE Colbern Road Second Floor Lee’s Summit, MO 64086 HAWAII 7304 Prince Kuhi Federal Building Honolulu, HI NEW YORK 1307 Federal Building 111 W. Huron Buffalo, NY 14202 Revised: 11 Aug 08 NEW YORK New York Office (NY) 201 Varick Street, Suite 1151 New York, NY 10014-4870 APX A-2 WASHINGTON DC Columbia Office (CF) 9300 East Hampton Drive Capitol Heights, MD 20743 WASHINGTON Seattle Office (ST) 11410 NE 122nd Way Room 312 Kirkland, WA 98034-6927 EST P/N AA107D APPENDIX B SPECIFICATIONS Model 195Ed Case Specifications LED Indicators Power On/Off Carrier Detect On/Off Link Status On/Off Receiver On/Off Transmitter On/Off I/O Connectors Ethernet 10/100Base T (Port 1) Ethernet 10/100Base T (Port 2) RS-232C Port (2,400 to 115.2K baud) RS-232C Programming Port (38.4 K baud) RJ-45 Female RJ-45 Female RJ-45 Female RJ-45 Female Antenna Input/Output TNC Reverse Polarity Female Remote Input Power Power Over Ethernet Cable Direct Input Power Optional, Header Screw Connector Transmiter 902 to 928 MHz Software Selectable 11 Channels 1,2,5.5,6,9,11,12,18,24,36,48, & 54 Mbps Fixed or Auto Scaling DSSS/OFDM Modulation 250 to 630 mW Frequency of Operation RF Data Rate Tx Output Power RF Output Impedance 50 ohms Receiver Rx Sensitivity @ Frame Error Rate <10% -72 dBm @54 Mbps to –95 dBm @ 1 Mbps Frame Error Rate <10% Power Power over Ethernet Power Connector on Unit Receive Transmit Case Dimensions Weight Outdoor Pole Mounting Kit IEEE 802.3af Standard Power Supply, 48 VDC @ 13 Watts 10 to 16 VDC 300 ma @ 12 VDC 1100 ma @ 12 VDC 1.9 in. H x 6.7 in. W x 6.2 in. L 1.25 lbs. Optional, EST P/N 195PM Other Warranty Temperature Range Humidity FCC ID Number (USA) IC Number (Canada) 1 Year -30° to +60° C 95% Non-condensing ENPESTEEM195ED 1457-195ED Specifications Subject to Change Without Notice APPENDIX B SPECIFICATIONS Model 195Ed Case Specifications APPENDIX B SPECIFICATIONS Antenna Specifications Model No: Antenna Type: Applications: Frequency: Polarization: Impedance: Gain: VSWR: Front to Back Ratio: Horizontal Beamwidth: Vertical Beamwidth: Antenna Material: Mounting Hardware: Antenna Connector: Antenna Envelope: Weight: AA191s Omni-Directional, Permanent Vehicle Mount Direct mount 896 to 940 MHz Vertical Caution 50 ohms Omni-directional antenna 7 dBi (5 dBd) should not be located within < 1.5 to 1 23 cm of personnel. n/a n/a n/a Molded Polymer Included TNC-R Male 32 in. length <1 lbs. Model 191Es Model: AA20DMEs Applications: Model 195Ed direct case mount Antenna Type: Omni-Directional, Sleeve dipole Frequency: 902 to 928 MHz Polarization: Vertical Impedance: 50 ohms Gain: 2 dBi (0 dBd) VSWR: < 2:1 Power: 10 W Front To Back Ratio: n/a Horizontal Beamwidth: n/a Vertical Beamwidth: 60 degrees Antenna Material: Polyurethane Plastic Radome Recommended Mounting Hardware: n/a Antenna Connector: TNC-R Male Flexibility: +/- 20 ° Antenna Envelope: 8.8 in. length by .51 in. width Temperature: -20 to +65 C° Weight: 35 grams Caution Omni-directional antenna should not be located within 23 cm of personnel. Model AA20DMEs Revised: 11 Aug 08 APX B-3 EST P/N AA107D APPENDIX B SPECIFICATIONS Antenna Specifications Model No: Antenna Type: Applications: Frequency: Polarization: Impedance: Gain: VSWR: Front to Back Ratio: Horizontal Beamwidth: Vertical Beamwidth: Antenna Material: Mounting Hardware: Maximum Power Input: Wind Survival: Bending Moment: Antenna Connector: Antenna Envelope: Weight: AA20Es900 Omni Directional, DC Grounded Fixed base 902 to 928 MHz Vertical 50 ohms 7 dBi (5 dBd) 1.5:1 Typical n/a n/a 22 degrees @ ½ power Brass radiator, UV inhibited fiberglass enclosed Base to Mast, Supplied. 150 Watts 100 mph 14.2 ft-lbs. @ 100 mph TNC-R Male with 36in. pig-tail. 48 in. L x 1-5/16 in. Dia. 1.75 lbs. Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 23 cm must be maintained between the antenna and all persons. Model AA20Es900 Revised: 11 Aug 08 APX B-4 EST P/N AA107D APPENDIX B SPECIFICATIONS Antenna Specifications Model No: Antenna Type: Applications: Frequency: Polarization: Impedance: Gain: VSWR: Front to Back Ratio: Horizontal Beamwidth: Vertical Beamwidth: Antenna Material: Mounting Hardware: Antenna Connector: Maximum Power Input: Antenna Envelope: Windload (RWV): Wind Surface Area: Weight: AA203Es900 Directional, DC grounded Fixed base. 902 to 928 MHz Vertical or Horizontal 50 ohms 7 dBi (5 dBd) < 1.5:1 Nominal > 16 dB 130 degrees @ ½ power 70 degrees @ ½ power Aluminum Heavy duty U bolts for mounting up to 2.0 in. pipe (included). TNC-R Male with 2 ft. pigtail with ESTeem weatherproof boot. 50 Watts 1.1 ft. length by 6 in. width 150 mph .11 ft² 1 lbs. Caution To comply with the FCC exposure compliance requirements, a separation distance of at least 23 cm must be maintained between the antenna and all persons. Model AA203Es900 Revised: 11 Aug 08 APX B-5 EST P/N AA107D APPENDIX C INTERFACE PORTS ETHERNET INTERFACE The ESTeem Model 195Ed’s Ethernet Port is a Full and Half-Duplex Auto-negotiation interface supporting both 10 Mbps and 100 Mbps (10/100BaseT). The Ethernet port is compliant with IEEE 802.3af Power Over Ethernet (PoE) to provide both data and power over the same CAT-5E grade Ethernet cable. The port is compatible with TIA/EIA-568B cable configuration (Figure 1). Figure 1: Ethernet Pin Layout A second Ethernet port will be included if the serial option is added to the 195Ed. This second Ethernet port can be used in Bridge Mode (HUB) or as a router. Revised: 30 Jun 08 APX C-1 EST P/N AA107D APPENDIX C INTERFACE PORTS CONFIGURING DHCP SERVER The ESTeem 195Ed Ethernet port supports both client and server Dynamic Host Configuration Protocol (DHCP). Figure 2 shows the DHCP host configuration screen that will be shown if DHCP server is selected in the setup screens. Enter the values that match the DHCP configuration for your network. Figure 2: DHCP Server Configuration Revised: 30 Jun 08 APX C-2 EST P/N AA107D APPENDIX C INTERFACE PORTS RS-232C PROGRAMMING PORT CONFIGURATION RS-232 Programming Port The ESTeem Model 195Ed has a proprietary RS-232C interface in a RJ-45 connector on the front panel. To interface the 195Ed to the serial port on the computer, you need ESTeem cable AA0621 that combines a standard Ethernet patch cable to a 9-pin Female adapter. The serial port on the ESTeem Model 192E can be used to access the configuration menu in the ESTeem for system and network configuration. The ESTeem communications port operates at 38,400 bps, No Parity, 8 Data Bits and 1 Stop Bit (38,400,N,8,1). Configure your terminal program to match these settings. Model 195Ed Serial Port Interface RS-232 PROGRAMMING PORT PIN-OUT TABLE ESTeem Model AA0621 RS-232C Port Pin-Out Table RJ-45 Pin No. Function Signal Ground (GND) Receive Data (RxD) Transmit Data (TxD) DB-9 Pin No. Ethernet Pin-out RS-232C DATA PORT CONFIGURATION RS-232 Data Port The ESTeem Model 195Ed has an RS-232C interface in a RJ-45 connector on the front panel that can be installed as an option . To interface the 195Ed to the serial port on the computer, you need serial cable with the following pin-out: ESTeem Model AA0621 RS-232C Port Pin-Out Table RJ-45 Pin No. Function Data Set Ready (DSR) Data Carrier Detect (DCD) Data Terminal Ready (DTR) Signal Ground (GND) Receive Data (RxD) Transmit Data (TxD) Clear to Sent (CTS) Request to Sent (RTS) Revised: 30 Jun 08 DB-9 Pin No. Model 195Ed Serial Data Port Interface APX C-3 EST P/N AA107D APPENDIX D RADIO CONFIGURATION 195Ed FREQUENCY OF OPERATION In a wireless Ethernet network all of the ESTeem Model 195Ed’s must be set to the same radio frequency of operation or channel. Listed on the right is a table showing the channel and corresponding frequency of operation. The frequency of operation is selectable when configuring the mode of operation of the 195Ed (reference Chapter 4). See Figure 1. RF COMMUNICATIONS DATA RATE Figure 1: RF Channel Selection The RF data rate of the Model 195Ed can be programmed for operation at 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, or 54 Mbps. The RF data rate can be set for a fixed rate or a specific range that is dynamically scaled by the Model 195Ed from monitoring the received signal quality. The Model 195Ed can communicate with multiple client 195Ed devices at different data rates for each device. By selecting all ranges from 1 to 54 Mbps you will be able to communicate with all client 195Ed regardless of their data rate and signal quality requirements. Dynamic scaling means that the Model 195Ed will operate at the highest RF data rate that is programmed into unit. If the received data quality drops below the required minimums for reliable communications the Model 195Ed will reduce the data rate to the next lowest step to increase signal quality. Conversely if the signal quality increases above the minimums the Model 195Ed will increase the RF data rate the next highest level. The ESTeem 195Ed is set at the factory to operate at maximized scaling speed data rates from 1-54 Mbps and should not need adjustment. The RF Data Rate is programmed in the Model 195Ed through the Advanced Menu>Wireless LAN Settings>Wlan0 Device and the value for wlan0_OPRATES:. In the example shown in Figure 2 the RF Date Rate is programmed to dynamic scale from 1 to 54 Mbps (recommend factory default setting). To set the values for the data rate, check the box next to the listed data rate to enable this rate for operation. Revised: 30 Jun 08 APX D-1 EST P/N AA107D APPENDIX D RADIO CONFIGURATION Figure 2: Advanced Data Rate Selection RF BASIC RATE The RF Basic Rate is the synchronization rate used to establish the initial connection between 802.11g and 802.11b communication devices in Mbps. After the initial connection has been establish the RF communication rate will be determined by the RF Communication Data Rate established above. Factory default is 1 through 11 Mbps shown in Figure 2 so that the unity will establish communication with the older (slower) 802.11b devices. This lower rate also allows for a quicker reconnect when the ESTeems are configured for EtherStation mode or working in a mobile environment. The ESTeem 195Ed is set at the factory to operate at all speeds from 1-11 Mbps and should not need adjustment. The RF Basic Rate is programmed in the Model 195Ed through the Advanced Menu>Wireless LAN Settings>Wlan0 Device and the value for wlan0_AP_BASICRATES:. In the example shown in Figure 2 the RF Date Rate is programmed to dynamic scale from 1 to 11 Mbps (recommend factory default setting). To set the values for the data rate, check the box next to the data rate required. Note: The Model 195Ed will only communicate with slower speed devices after synchronization if the RF Communication Data shown above has been set to dynamically scale to 1 and 2 Mbps. In general, do not set the RF Basic Rates above 11Mbps unless specifically instructed by ESTeem Customer Support. Revised: 30 Jun 08 APX D-2 EST P/N AA107D APPENDIX E SECURITY OVERVIEW The security for the ESTeem Model 195Ed, like all network security, must be multi-layered. One level of security is never enough to make sure that data does not end up in the wrong hands. Please review the following security levels and decide what is the most appropriate for your network. 128-BIT WEP The 128 WEP uses a particular algorithm called RC4 encryption to encode and decode traffic that is based on a 104-bit encryption key and a 24-bit Initialization Vector (IV). RC4 starts with a relatively short encryption key (104 bits) that is expanded into a nearly infinite stream of keys to accompany the stream of packets. The basic concept of RC4 is good, but the way it’s implemented in WEP leaves it open to compromise. The researchers that test the integrity of the system usually focus on one piece of the implementation, the Initialization Vector (IV). The IV (24 bits) is the algorithm component that’s supposed to keep expanded keys from repeating. From the researcher’s point of view, a high-volume access point is mathematically guaranteed to reuse the same key stream at least once a day. When this happens, it’s called an IV collision this becomes a soft spot to enter the system. The researchers aren’t saying that it’s easy to break into the system, or that it’s being done on a regular basis, only that it is possible and that administrators should consider ways to reduce the possibility. WPA Wi-Fi Protected Access with Preshared Key (WPA PSK) WPA, which uses 802.1x, was introduced in 2003 to improve on the authentication and encryption features of WEP. All authentication is handled within this access point device. WPA has two significant advantages over WEP: 1. An encryption key differing in every packet. The TKIP (Temporal Key Integrity Protocol) mechanism shares a starting key between devices. Each device then changes their encryption key for every packet. It is extremely difficult for hackers to read messages even if they have intercepted the data. 2. Certificate Authentication (CA) can be used, blocking a hacker posing as a valid user. Wi-Fi Protected Access with Enterprise Server (WPA Enterprise) Like WPA PSK, WPA Enterprise uses 802.1x. However, a backend authentication server handles the authentication decision. The most commonly type of authentication server is a RADIUS server. The ESTeem Model 195Ed can be configured to operate with an established RADIUS server on the network. WPA is server/client relationship from a software driver on a computer’s wireless LAN (WLAN) card to an Access Point. The scope of WPA is limited in use to this configuration only. The ESTeem Model 195Ed can support WPA Enterprise and PSK as an Access Point, but the level of security on the Bridging layer is configured separately. ACCESS CONTROL LIST (ACL) The ACL is one of the simplest yet most secure methods of network security. The ACL is a configurable MAC filter in the Model 192E that can be set to allow specific MAC address on the wireless network by individual address or address ranges. The same filter can also be set to reject individual MAC addresses or address ranges. The MAC address is a unique, 6 hexadecimal field address assigned at the manufacturer that can not be changed. The MAC address is traceable through the IEEE governing body to the manufacturer and is the “fingerprint” for all Ethernet devices. Revised: 30 Jun 08 APX E-1 EST P/N AA107D APPENDIX E SECURITY Using a combination of both the WPA or 128-Bit WEP encryption and the ACL filter provide the ESTeem an extremely secure wireless networking layer. DISABLING BROADCAST PROBES AND HIDING SSID A simple but very effective way of securing a network is to make the network difficult to find. By disabling broadcast probes and hiding the Service Set Identification (SSID), wireless and network “sniffers” will not be able to find your ESTeem Model 195Ed network. To gain access to the wireless network, you would be required to have the SSID and all security loaded in the WLAN card software prior to entering the network. MASQUERADE MODES When the ESTeem Model 195Ed is configured in either the Access Point Masquerade or the Client Masquerade modes, the wireless modem functions as a network firewall. If access to the wired network is the greatest concern, place the ESTeem in the Masquerade mode and the wireless network will be completely isolated from the wired Ethernet network. INCREASING NETWORK SECURITY The following are a few suggestions to help improve the overall security of your wireless network: 1. Enable the security. If you research all of the articles regarding hackers, they have gotten into the user’s network due to the security not being enabled. 2. Set the ACL filter to include only those MAC address of the wireless Ethernet device being used on the network. 3. Set "Hide SSID" to True. As you take your access point out of the box, broadcast SSID is enabled which means that it will accept any SSID. By hiding the SSID configured in the client must match the SSID of the access point. 4. Make sure the keys are not reused in your company, since reuse increases the statistical likelihood that someone can figure the key out and change the default password on your access point or wireless router 5. Change the default SSID of your product. Don't change the SSID to reflect your company's main names, divisions, or products. It just makes you too easy to target. 6. As a network administrator, you should periodically survey your company using a tool like NetStumbler to see if any "rogue" access points pop up within your company without authorization. All of your hard work to "harden" your wireless network could be wasted if a rogue AP was plugged into your network behind the firewall. 7. Many access points allow you to control access based on the MAC address of the NIC attempting to associate with it. If the MAC address of your NIC isn't in the table of the access point, you won't associate with it. And while it's true that there are ways of spoofing a MAC address that's been sniffed out of the air, it takes an additional level of sophistication to spoof a MAC address. The downside of deploying MAC address tables is that if you have a lot of access points, maintaining the tables in each access point could be time consuming. Some higher-end, enterprise-level access points have mechanisms for updating these tables across multiple access points of the same brand. 8. If you're deploying a wireless router, think about assigning static IP addresses for your wireless NICs and turn off Dynamic Host Configuration Protocol (DHCP). If you're using a wireless router and have decided to turn off DHCP, also consider changing the IP subnet. Many wireless routers default to the 192.168.1.0 network and use 192.168.1.1 as the default router. 9. A simple security technique used by the military is to have the administrator periodically change the key for the system i.e. weekly, monthly, etc. Revised: 30 Jun 08 APX E-2 EST P/N AA107D APPENDIX F TROUBLESHOOTING TESTING COMMUNICATION LINK After you have configured at least two of the Model 195Ed wireless Ethernet modems for operation, you can verify communication with each the following steps: Status LED Solid Red on Link Status Light The quickest source of link status is to view the Status Light on the face of the 195Ed (Figure 1). If the Status light is solid on any other 195Ed except the Timing Master, the Model 195Ed has a connection to another Model 195Ed listed in the Peer Table. On the Timing Master the status light will be illuminated at all times. Status Screen/Peer Table Figure 1: Connection Status Light To view detailed information on the status of the communication link (such as connection speed, signal strength and last update time) you can open the Status Screen from the Web Interface. After press the Status tab at the top of the screen the Status: Summary will be displayed showing the status of all ports and memory in the 195Ed (Figure 2). Figure 2: Peer Summary Table Revised: 30 Jun 08 APX F-1 EST P/N AA107D APPENDIX F TROUBLESHOOTING Under the Wireless Status heading click on the View Peer Table and the Peer Table Screen will be displayed (Figure 3). Opposite Modem’s Wireless MAC Receive Signal Strength (dBm) Last Packet Received Peer Modem ID Other Access Points Figure 3: Repeater Peer Table Repeater Peers - The Peer Table will display all connected 195Ed configured to repeat to this ESTeem by their Wireless (WLAN) MAC address. Received Signal Strength – This is the first of the two numbers listed in the block. This signal strength value is listed in dBm. Last RX – This is the time of the last received data packet. When monitoring the status menu, it is important to note the time the last transmission was updated so you are not looking at “stale” data. Current Data Rate – This is the current speed the last data packet received by the Model 195Ed. Note that the speed is listed in kbps. Modem ID – This is Modem ID for the opposite repeater peer. Revised: 30 Jun 08 APX F-2 EST P/N AA107D APPENDIX F TROUBLESHOOTING Peer Table Details To further analyze a repeater peer link, press the hyperlink for any WLAN MAC address listed in the repeater peer summary (Figure 3) and the Peer Info screen will be displayed (Figure 4). Detailed information on the Counter, Statistics, Link Encryption, Beacon and Probes can found by selecting the respective hyperlink. Figure 4: Repeater Peer Table TROUBLESHOOTING TIPS General (Applicable to All Modes of Operation) Where do I find the latest firmware version number? – We have the latest version number of the Model 195Ed firmware listed on the ESTeem Web site (www.esteem.com) under the Model 195Ed product page. How and when do I update the Model 195Ed firmware? - You should only update the Model 195Ed firmware if you are having a specific problem and it is recommended that you do so by ESTeem Customer Support personnel. All the update instructions and files are located on the ESTeem FTP site at the following address: ftp://www.esteem.com/195Ed Do all firmware versions have to be the same to communicate between the Model 195Ed? – It is not necessary for all the firmware versions to be the same revision to communication, but the later version may have added features that the other versions will not recognize. What characters are valid for WEP Key entry? - Only the Hexadecimal characters 0-9 and A-F are valid for key entry. What ESTeem Utility version is required to program the Model 195Ed? – The ESTeem Utility program is not required to program the Model 195Ed. The 195Ed can be programmed using any Terminal Emulation program (such as Windows HyperTerminal) and any web browser program. Revised: 30 Jun 08 APX F-3 EST P/N AA107D APPENDIX F TROUBLESHOOTING What is the speed and duplex configuration on the Model 195Ed – The Model 195Ed is an auto-negotiation full/half-duplex 10/100 Base-T interface. Ether a cross-over or patch cable is supported. Access Point Repeater Mode If I am unable to communicate with any of the remote sites, what is the most common cause? - The most common cause a communication problems with the 195Ed is that the SSID was entered incorrectly for the radio network. The 195Ed uses the SSID to set the frequency hopping pattern and it must be the same on all modems. How long does it take to re-establish the Wireless Ethernet Network? - If a communication link is lost and the Wireless Network needs to re-establish the repeater routes, the time can take up to 30 seconds. Should the AP Repeater Mode be used on mobile equipment? - The AP Repeater mode should be used on equipment that will not change the Repeater Route as it moves. For example, if a mobile device such as a crane can communicate directly to another ESTeem and will not loose the link in its travel, the AP Repeater Mode could be used. If the device requires two ESTeem Model 195Ed’s (Base and Repeater) to maintain communication across its complete travel, the Station Modes should be used on the mobile device. The problem will be in the time that the mobile ESTeem will take to transfer between the two sites. In Access Point Repeater mode the transfer can take up to 30 seconds, while the EtherStation mode will transfer without a packet loss. Does WEP have to be used? – The WEP does not have to be enabled for the modems to communicate, but all modems must be configured the same way. Correct configuration, but cannot establish communications. – In addition to the network configuration, all 195Ed modems configured in the AP mode must share the same SSID and be on the same frequency channel. The most likely cause of the error is the WLAN MAC address is not configured in both 195Ed’s repeater tables. If only one side is configured, everything will appear to be correct but no communication will function. EtherStation How do I access the Model 195Ed web page in EtherStation Mode? The Model 195Ed does not have an active web browser when configured in EtherStation mode. You must access the ESTeem with the ESTeem Discovery Program or through the RS-232 port after configuration in this mode. To monitor the link status, you can use the EtherStation Status program. What IP address do I configure the ESTeem in EtherStation mode? – The Model 192E will not have an IP address in EtherStation mode. I can not link my device into the wireless network – Verify that the MAC address of the device is exactly the same as configured in the Model 195Ed. The MAC address must have colons between the values. Can I connect my Model 195Ed in EtherStation mode to a HUB or Ethernet Switch? – No. The modem must be connected directly to the Ethernet device for which it is programmed. In EtherStation mode the Model 195Ed can only service ONE Ethernet device. Revised: 30 Jun 08 APX F-4 EST P/N AA107D APPENDIX G UTILITIES & FEATURES ESTEEM DISCOVERY UTILITY The ESTeem Discovery Utility will allow you to configure the IP address on the Model 195Ed to match your network regardless of its current IP subnet. This utility will also allow you to update the software in the 195Ed and open the web configuration for that wireless modem. Installation To install the Discovery Utility on your computer, inserting the Resource Disk in your CD drive. Note: The ESTeem Resource Disk is stand-alone copy of Figure 1: ESTeem Resource Main Page the ESTeem Web site (Figure 1). Navigation of the Resource Disk is as simple as using your web browser. All technical documentation, User’s Manuals and the ESTeem Utility Program is available on the disk. 1. Place the ESTeem Utility CD in your CD-ROM drive. The CD will auto load the ESTeem main page Note: If the page does not auto load, open your web browser and set your address line to D:\index.html (Where D: is the drive letter for your CD-ROM drive). 2. From the Main Page select ESTeem Utilities and click on ESTeem Discovery Utility (Figure 2). Note: This program is saved in a compressed file format. Microsoft Windows XP® will open the file directly, but other operating systems will require a common compression program such as WinZip available for download at http://www.winzip.com Figure 2: Discovery Utility Download Revised: 30 Jun 08 APX G-1 EST P/N AA107D APPENDIX G UTILITIES & FEATURES 3. Double click on the 195EdiscoverySetup.exe file listed in the window to install the program. 4. Connect the Model 195Ed to your computer either direct to the Ethernet card or through a HUB/Switch using a CAT-5e Ethernet cable. The Ethernet port on the 195Ed supports Auto-Negotiation so either a patch cable or crossover cable will work. Open the ESTeem Discovery Program and press the Discover Modems button. The Model 195Ed will be displayed in the program by the Ethernet MAC address and Current IP Address (Figure 3). Figure 3: Discovery Program Main Page Note: The SSID, Mode of Operation and Modem ID will be adjusted through the web configuration manager.. 5. Double-click on the 195Ed you want to program and the Configure IP Address window will be displayed (Figure 4). Enter an IP address and Subnet Mask for the 195Ed that matches your network subnet and press the OK button to save this to the ESTeem. You will receive notification that the Configuration was Successful and the 195Ed will reboot. Proceed to ESTeem Setup in Chapter 4. Figure 4: Change IP Address Window Revised: 30 Jun 08 APX G-2 EST P/N AA107D APPENDIX G UTILITIES & FEATURES Firmware Updates To update firmware on any ESTeem Model 195 that is shown on the Discovery program, “right-mouse” click on the 195’s MAC address and select Update from the menu (Figure 5). Once you locate the update file, select the Open button and the 195 will update, validate and then reboot with the updated operating system. Figure 5: Discovery Features Menu Opening Web Browser To quickly open a web browser page to the IP address programmed in the 195 modem, “right-mouse” click on the 195’s MAC address and select Open Browser from the menu (Figure 5). If your computer is configured for the same IP subnet at the ESTeem 195 wireless modem, you will be asked to sign in with the Username and Password (Figure 6) and you can begin programming the Model 195 for your application. Figure 6: ESTeem Web Page Log-on Screen Revised: 30 Jun 08 APX G-3 EST P/N AA107D APPENDIX G UTILITIES & FEATURES ETHERSTATION STATUS PROGRAM When configured for EtherStation mode, the Web Configuration Manger is turned off. To gather information from the 195Ed on Access Point, link status and received signal strength you will need to install the ESTeem 195E Status Utility. The EtherStation Status Utility version 2.0.0.0 or greater provides a new feature where it will automatically program the connected ESTeem 195Ed to match up with the computer running the software. This software requires that the ESTeem 195Ed has software version 302.8.102 or greater installed for this feature to function. This software program is found on the AA109 Resources Disk or available from the ESTeem web site. To install the utility, please complete the following: Installation The ESTeem Discovery Utility will allow you to configure the IP address on the Model 195Ed to match your network. Install the Discovery Utility on your computer by inserting the Resource Disk in your CD drive. Note: The ESTeem Resource Disk is stand-alone copy of the ESTeem Web site (Figure 1). Navigation of the Resource Disk is as simple as using your web browser. All technical documentation, User’s Manuals and the ESTeem Utility Program is available on the disk. 1. Place the ESTeem Utility CD in your CD-ROM drive. The CD will auto load the ESTeem main page Note: If the page does not auto load, open your web browser and set your address line to D:\index.html (Where D: is the drive letter for your CD-ROM drive). 2. From the Main Page select ESTeem Utilities and click on EtherStation Status Utility Note: This program is saved in a compressed file format. Microsoft Windows XP® will open the file directly, but other operating systems will require a common compression program such as WinZip available for download at http://www.winzip.com 3. Double click on the 195EStatusSetup.exe file listed in the window to install the program. 4. Connect the Model 195Ed to your computer either direct to the Ethernet card or through a HUB/Switch using a CAT-5e Ethernet cable. The Ethernet port on the 195Ed supports Auto-Negotiation so either a patch cable or crossover cable will work. Open the ESTeem Status Program and a status icons will appear in your system tray (Figure 9). When the status menu is opened from the system tray, the status window will be displayed (Figure 7) to show the Access Point MAC address and signal strength. The tray icon and Signal Strength bar will display the colors from Green, Yellow to Red on progressively poorer signal or will show Grey if roaming. Figure 7: EtherStation Status Program Note: This Utility will only operate with an ESTeem Model 195Ed in EtherStation mode. Revised: 30 Jun 08 APX G-4 EST P/N AA107D APPENDIX G UTILITIES & FEATURES SETTING LOCAL TIME The ESTeem Model 195Ed will be shipped from the factory with the internal real-time clock set to Pacific Time. To change the clock settings to the local time for accurate log file entries: 1. Select Advanced from the top Menu then Wireless LAN Settings>wlan0 device and press the Next button (Figure 8). 2. Select Global Settings>Set System Time from the menu and press the Next button to continue. Figure 8: Advanced Features Screen 3. Select the correct date and time from the drop-down menus (Figure 9) and press the Set System Time button to save the time to the real time clock. Figure 9: Advanced Features Screen Revised: 30 Jun 08 APX G-5 EST P/N AA107D APPENDIX G UTILITIES & FEATURES CONFIGURING TIME SERVER Enabling NTP time synchronization services on the ESTeem 195Ed will allow to use time services from upstream services to keep the time on the system accurate. To allow time synchronization, the Model 195Ed must be configured with the NTP Daemon enabled and the appropriate IP address of the upstream network NTP server. 1. Select Advanced from the menu items and Global Variables (Figure 10). Figure 10: Advanced Settings Menu Revised: 30 Jun 08 APX G-6 EST P/N AA107D APPENDIX G UTILITIES & FEATURES 2. Press the next button and Figure 11 will be displayed. At the bottom of the page are the NTP server configurations. 3. The NTP daemon is enabled by selecting YES for NTP ENABLE (Figure 11). When enabled, the NTP daemon will use time services from upstream services to keep the time on this system accurate. Figure 11: NTP Settings 4. Next, the NTP SERVICE ENABLE should be configured to “YES,” if you want to allow the system to provide NTP service for clients wishing time synchronization (Figure 11). 5. The final step in configuring NTP services is to enter the IP address or the host name of the upstream NTP server. Revised: 30 Jun 08 APX G-7 EST P/N AA107D APPENDIX G UTILITIES & FEATURES 6. Once configuration is complete, press the “Return to Advanced” button. Figure 12: Advanced Settings Menu 7. To complete the configuration, select “Commit and Reboot.” The ESTeem 195Ed will now commit the configuration changes and reboot. (Figure 12) Revised: 30 Jun 08 APX G-8 EST P/N AA107D
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 35 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:cbfc720d-6530-461c-811d-0177107064ec Modify Date : 2008:08:15 15:34:27-07:00 Create Date : 2008:08:15 15:34:19-07:00 Metadata Date : 2008:08:15 15:34:27-07:00 Document ID : uuid:721da384-270e-4d22-a27e-9abe0032410f Format : application/pdf Title : 195Ed Chapter 0 - Front Cover 195Ed Creator : PDFCreator Version 0.9.5 Author : Marske Subject : Producer : GPL Ghostscript 8.61EXIF Metadata provided by EXIF.tools