Elentec ESG-BTM1000 Bluetooth module for Active 3D Glasses User Manual 04 Module Manual Rev 1
Elentec Co., Ltd Bluetooth module for Active 3D Glasses 04 Module Manual Rev 1
Elentec >
User Manual
Specification
Battery : CR2025
Supply voltabe ; 3.0V
Power consumption : 1.2mA, 3.6mW
Weight : 1.3g
Size : 24.4mm*27.4mm
FCC ID : 2AAQYESG-BTM1000
IC : 11307A-ESGBTM1000
FCC :
When the module is installed inside another device, then the outside of the device into which the
module is installed must display a label referring to the enclosed module with the following statement:
‘‘Contains Transmitter Module FCC ID: 2AAQYESG-BTM1000’’
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications to the equipment not expressly approved by the party responsible
for compliance could void user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IC ;
“The host device must be labeled to display the Industry Canada certification number of the module
as follows:
Contains transmitter module IC: 11307A-ESGBTM1000.
where 11307A-ESGBTM1000 is the
module’s certification number
“L'appareil hôte doit porter une etiquette donnant le numéro de certification du module d'Industrie
Canada comme suit:
Contient le module d'émission IC: 11307A-ESGBTM1000 où 11307A-ESGBTM1000 est le numéro
de certification du module.”
. For Industry Canada the user manual must contain the user instructions in French language:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement
Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.”
This device complies with Industry Canada RSS-210. Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio RSS-
210. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
Cofetel notice :
“La operaci n de este equipo est sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y
(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la
que pueda causar su operaci n no deseada.”