Elexa Consumer DMDP1 Door / window sensor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3486128
Application ID	QNGra9Ulh/eigS8PIKLmJA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.69kB (246134 bits)
Date Submitted	2017-07-28 00:00:00
Date Available	2017-07-28 00:00:00
Creation Date	2017-06-06 11:12:51
Producing Software	Adobe PDF Library 15.0
Document Lastmod	2017-06-06 11:12:53
Document Title	user manual
Document Creator	Adobe InDesign CC 2017 (Windows)

Thank you for purchasing the DOME
Door/Window Sensor Pro! Use this device with
your Z-Wave Certified Controller to monitor
doors, windows, and other openings in your
home and also to monitor ambient temperature
levels.
LED Indicator
Connect/Tamper Button
Reed Switch
Door/Window Sensor Pro
DMDP1
Screw Holes
Key Features
• Z-Wave Plus Certified
• S0 Security-Enabled*
• Built-In Temperature Sensor (off by default)
• Up to 260’ range
• Ten-Year Battery Life
• LED Signal Strength Indication
• 1” Max distance between sensor & magnet
• Ultra-Narrow (1/4”) Magnet for Placement
Between Door and Casing
• Monitor doors, windows, medicine cabinets,
drawers, garage doors, and many other openings
Sensor Cover Release Button
*Encrypted communication requires S0-capable controllers.
Figure 1 - Main Parts of the Door/Window Sensor Pro
Including/Connecting into the Z-Wave Network:
(Door/Window Sensor Pro not yet powered on)
Follow the instructions for your Z-Wave certified Controller to
enter inclusion mode. When prompted by the Controller:
1. For proper inclusion, bring the Door/Window Sensor Pro to
where it will be used.*
2. Remove the Battery Tab.
The LED Indicator will alternate between green and red, then flash
green three times indicating inclusion.
Including/Connecting into the Z-Wave Network:
(Door/Window Sensor Pro already powered on)
Follow the instructions for your Z-Wave certified Controller to
enter inclusion mode. When prompted by the Controller:
1. For proper inclusion, bring the Door/Window Sensor Pro to
where it will be used.*
2. Open the Sensor Cover.
3.
Press the Connect/Tamper Button three times and the LED
Indicator will alternatingly flash green and red until inclusion.
The LED Indicator will alternate between green and red, then flash
green three times indicating inclusion.
*For non Z-Wave Plus networks, please consult the owner’s manual for your
primary controller to determine the best method and location for adding the
Door/Window Sensor Pro to your Z-Wave network.
Excluding/Disconnecting from the Z-Wave Network:
Follow the instructions for your Z-Wave certified Controller to
enter exclusion mode. When prompted by the Controller:
1. Remove the Cover of the Door/Window Sensor Pro.
2.
Press the Connect/Tamper Button quickly 3 times in a row.
The LED Indicator will flash three times indicating exclusion/disconnection, then start blinking yellow (red + green.)
Resetting the Door/Window Sensor Pro to Factory
Default Settings:
To disconnect from the Z-Wave Network and restore factory default
settings:
1. Open the Cover and make sure the Door/Window Sensor Pro
is powered.
2.
Wait 5 seconds.
3.
Move the magnet in and our of the closed position 6 times.
4.
The LED Indicator will light red for 2 seconds indicating successful reset, then start blinking yellow (red + green.)
Only do this if the controller is disconnected or otherwise unreachable!
Installation
NEED HELP? CONTACT DOME CUSTOMER SERVICE
Install the Door Sensor and Magnet by either using the
pre-applied double-stick tape or included hardware. To expose the screw holes, remove the cover and battery from
the Door Sensor and Magnet. For proper operation, there
should be no more than a 1” gap between Door Sensor and
Magnet.
Max 1”
Figure 2 - Sensor Alignment
If you have questions, our trained Customer Service Department is happy to assist you 24
hours a day, 7 days a week. Contact Dome Customer Service as follows: • In North America
dial: 1-855-249-1754 • Email Dome at support@domeHA.com
DO NOT RETURN THIS PRODUCT TO THE STORE OR WEBSITE FROM WHICH IT WAS
PURCHASED If you believe the product is defective, has a missing or broken part or are having
difficulty with it please contact Dome as listed above for a quick and efficient solution to the
problem.
Legal Notices: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Reorient or relocate the receiving
antenna; increase the separation between the equipment and the receiver; connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult
the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user authority to operate the equipment
Operation description: the Door sensor is running with a 32M CPU. When the state (open/
close) of Door changes, the trigger circuit will send a signal. Once CPU detects the trigger
signal, it will output a RF signal through a matching network and a filter
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
1 Year Limited Warranty
Elexa Consumer Products, Inc. (”ECP”) warrants to the original retail purchaser (”Purchaser”) that the DOME Siren (the “Product”) will be
free of defects in materials or workmanship
under use for one (1) year from the date of
purchase (the “Warranty period”).
For the Purchaser only, if the Product fails to
perform as specified during the Warranty Period due to defective parts or faulty workmanship, ECP will repair or replace the defective or
damaged parts of the Product. Normal wear
and tear is not covered nor is abnormal use,
misuse, mishandling, faulty installation, improper shipping, damage caused by disasters
such as fire, flood or earthquake, neglect, accident or tampering. This warranty covers only
normal use in the United States or Canada.
To obtain warranty service during the Warranty
Period, call Dome Customer Service (1-855249-1754) or email: support@domeHA.com
for instructions on sending damaged parts
and documentation for a Return Material Authorization (RMA). Products returned to ECP
for repair or replacement without authorization will be returned at the sender’s expense.
All warranty claims must be accompanied by
a legible copy of the original receipt showing
date and details of purchase. The RMA number must be clearly written on the side of the
shipping container in which you return the
Product or defective parts. Unless otherwise
instructed by ECP, the Product must be sent
freight pre-paid to the following address:
Elexa Consumer Products, c/o Promac,
1153 Timber Dr., Elgin, IL 60123
ECP will repair or replace the defective parts
and return them at ECP’s cost by a shipping
method selected by ECP. When contacting
ECP to obtain an RMA, Purchaser may request
expedited return shipping at Purchaser’s expense.
THIS WARRANTY IS NOT TRANSFERABLE,
AND, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IS IN LIEU OF ALL
OTHER WARRANTIES, REPRESENTATIONS
AND CONDITIONS, EXPRESSED OR IMPLIED,
STATUTORY OR OTHERWISE, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO OTHER PERSON
OR REPRESENTATIVE IS AUTHORIZED TO
MAKE ANY OTHER WARRANTY ON BEHALF
OF ECP OR ASSUME FOR ECP ANY OTHER
LIABILITY IN CONNECTION WITH THE SALE
OF THIS PRODUCT. IN NO EVENT WILL ECP
BE LIABLE FOR ANY DAMAGES, INCLUDING
BUT NOT LIMITED TO INCIDENTAL, SPECIAL
OR CONSEQUENTIAL DAMAGES ARISING OUT
OF THE USE OR INABILITY TO USE THE PRODUCT, INCLUDING DAMAGES DUE TO ECP’S
NEGLIGENCE.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS WHICH VARY FROM STATE
TO STATE AND COUNTRY TO COUNTRY.
CORRECT DISPOSAL OF BATTERIES IN THIS PRODUCT
This marking on the product, accessories or literature indicates that the product and
its electronic accessories should not be disposed of with other household waste.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their government office, for details of where and how they can take these
items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product and its electronic accessories should not be
mixed with other wastes for disposal.
This marking on the battery, manual or packaging indicates that the batteries in
this product should not be disposed of with other household waste. Where marked,
the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury,
cadmium or lead above the reference levels in EC Directive 2006/66. If batteries are
not properly disposed of, these substances can cause harm to human health or the
environment.
# VII-DMDP1
©2016 Elexa Consumer Products, Inc.
2275 Half Day Rd., Suite 333
Bannockburn, IL 60015
www.domeHA.com
For more detailed instructions on using the
Door/Window Sensor Pro with your hub,
please visit:
www.domeha.com/how-tos

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Language                        : en-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c138 79.159824, 2016/09/14-01:09:01
Create Date                     : 2017:06:06 11:12:51-05:00
Metadata Date                   : 2017:06:06 11:12:53-05:00
Modify Date                     : 2017:06:06 11:12:53-05:00
Creator Tool                    : Adobe InDesign CC 2017 (Windows)
Instance ID                     : uuid:9cf93655-53a6-44e3-af5f-3ebfb92a2902
Original Document ID            : xmp.did:A82C12DC113EE611942C83DCD861EE7F
Document ID                     : xmp.id:8ad4fb53-fd03-f340-888e-c0bfa0b6d44e
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:88ea83d1-cd04-4847-b450-3ea16b3f9025
Derived From Document ID        : xmp.did:ABB709DD8F62E6119155ABB1BB463EC3
Derived From Original Document ID: xmp.did:A82C12DC113EE611942C83DCD861EE7F
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CC 2017 (Windows)
History Changed                 : /
History When                    : 2017:06:06 11:12:51-05:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 15.0
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CC 2017 (Windows)

EXIF Metadata provided by EXIF.tools