Elpas Solutions 3-63040 Wiegand 26 Bit Proximity Reader User Manual

Elpas Solutions Ltd. Wiegand 26 Bit Proximity Reader 1

a href="https://usermanual.wiki/Elpas-Solutions" itemprop="url"> Elpas Solutions >

Users Manual

www.elpas.com Page 1 of 2 DE6302_V4_09/13 VisAccess RDR-2/RDM-2 External 26-Bit Wiegand Proximity Readers Installation Guide 1. INTRODUCTION The RDM-2 (Mullion type) and RDR-2 are external proximity readers, compatible with the Prox-in-a-Box (PIAB) access control system. The system is designed to limit access to restricted areas, while permitting authorized people to enter. The readers are 26-bit Wiegand compatible proximity readers and can be used with any other compatible access control system. It is recommended to install the readers on a wall outside the protected area, and the PIAB control unit inside the protected area. Proximity access cards or tags are used as keys to open these doors. When in the presence of the readers, the access card emits a coded RF signal that is read by the proximity reader. The RDR-2/RDM-2 then forwards this signal to the PIAB control unit. The control unit verifies that the card is valid and makes the decision as to whether it should energize an output relay that releases the lock. All activity involving the proximity readers is recorded and logged. RDR-2 RDM-2 Fig. 1 External View For information about the PIAB system, refer to the PIAB user’s guide and installation instructions. 2. SPECIFICATIONS Format: 26-bit Wiegand serial communication Indicators: Tri-color LED (green, red, amber). Frequency: 125 kHz Tag reading range: RDR-2: 50 - 100 mm (2 - 4 in.) RDM-2: 40 - 80 mm (1 - 3 in.) Current Drain: Nominal 50mA, Max. 70mA @12VDC Operating temperature: -20°C to 50°C (-4°F to 122°F) Dimensions (L x W x D): RDR-2: 116 x 70 x 16.8 mm (4 - 1/2 x 2 - 3/8 x 5/8 in.) RDM-2: 94 x 43 x 16 mm (3.7 x 1.7 x 0.6 in.) Cable (to PIAB control unit) maximum length: 6-conductor cable 22 AWG up to 60 m (200 ft) 18 AWG up to 100 m (320 ft) Minimum distance between readers: 60 cm (2 ft) Environmental Protection (Solids, Liquids, Impact): IP677 Weight: RDR-2: 121.5 g (4.3 oz) RDM-2: 105 g (3.7 oz) Color: Metallic brown (option - white) 3. MOUNTING Mount the proximity reader outside the door on the wall or door frame. The RDR-2/RDM-2 comes with a 1m (3 ft) wire lead. To mount the proximity reader: A. Insert a screwdriver into the recess at the bottom or top of the case, and separate the cover from the reader. B. Place the base on the installation surface, mark two screw holes, drill the holes, and insert plastic anchors, if necessary. Figure 2. RDM-2 Mounting C. Fasten the base to the mounting surface, using two screws. D. Replace the reader’s cover, ensuring that the cover is aligned with the reader. This enables the LED to be visible. Figure 3. RDR-2 Mounting Note: Do not install the RDR-2/RDM-2 on a metal surface or a metal door frame, since this decreases the read range significantly. If you have to install the reader on a metal surface, use a spacer so that the reader will be at least 1 cm (3/8 in.) away from the metal. You may use RDR BACK (for RDR-2) or RDM-BACK (for RDM-2) which is an optionally available spacer made specifically for this purpose. Note: When installing more than one reader, the distance between the readers should be at least 60 cm (2 ft.), to ensure proper operation.
Download:
Mirror Download [FCC.gov]
Document ID2091143
Application IDSJNjB8v/BRxZ/HbZ/UFR4w==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize58.11kB (726322 bits)
Date Submitted2013-10-17 00:00:00
Date Available2013-10-17 00:00:00
Creation Date2017-10-25 14:50:49
Producing SoftwareGPL Ghostscript 9.18
Document Lastmod2017-10-25 14:50:49
Document Title1
Document CreatorMicrosoft® Word 2010
Document Author: Gideon
FCC ID Filing: O4X3-63040

Navigation menu