Elpas Solutions B05 User Manual corrected

Download:
Mirror Download [FCC.gov]
Document ID	113752
Application ID	kVvbJy0xFdixBTy8vUkgiA==
Document Description	corrected user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	8.52kB (106497 bits)
Date Submitted	2000-08-17 00:00:00
Date Available	2000-11-07 00:00:00
Creation Date	2000-08-17 07:14:56
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2000-08-17 07:14:58
Document Title	corrected user manual

Alert Tag Instruction Manual and Spec-Sheet
FCC Compliance
The FCC Wants You to Know
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment
and receiver.
c) Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
d) Consult the dealer or an experienced radio/TV
technician.
FCC Warning
Modifications not expressly approved by manufacturer could void
the user authority to operate the equipment under FCC rules.
15.9 (a) Labeling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions. (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
IR and RF Alert Tag
P/N: ALB00001 (433.92 MHz)
Feirmware ver2
IR/RF Alert Tag
Description
A small light-weight, oval badge. The tag sends Infra Red signals, and in addition
sends RF signals in the frequency of 433.92 MHz. Designed especially for the
convenience of the elderly or persons in stressful situations (alert, panic, etc.).
General
Electrical power
source
Data rate
Modulation
Message
protocol
Message
duration
Button on badge
Battery type
Battery life
Battery status
indication
Badge ID
Dimensions
Weight
(including
battery)
Temperature:
Operating
Temperature:
Storage
One 3 - Volt lithium battery
19,200 bits per second
ASK
(Amplitude Shift Keying of IR or RF carrier)
4 bytes proprietary format
2.08 ms
Location dependent function.
Button press message transmitted on IR.
CR 2032 Renata
One year, assuming movement 8 hr / day
Battery status transmitted with every RF and IR message
Unique factory programmed
Pendant shape 55 x 35 x 18 mm
25 gram
-10 to 70°C
-20 to 60°C
Humidity:
Operating
Humidity :
Storage
Accessories
Operating – 5 to 95% RH @ 70°C
Non Operating (12 Hours) – 5 to 95% RH @ 85 °C
Neck strap (included)
IR Transmission
Peak optical
transmitted
power
Peak
transmission
wavelength
Peak radiant
intensity
Frequency of
transmission
Transmission
rate
Transmission
angle
500mW
880nm
120 mW/Sr
Carrier at 455 KHz
Motion – every 10 sec message
Motionless – every 60 sec message.
360° badge plane. ±60° to badge perpendicular axis
RF Transmission
433.92 MHz
Modulation
Transmission
rate
Average ERP
Effective
Radiated Power
Stability
Peak ERP
Transmission
pattern
ASK
(Amplitude Shift Keying of 433.92 MHz carrier)
Every 10 sec message.
- 70 dbm max
+/- 20ppm
-20 dbm (max)
Omnidirectional
Using the Alert Tag
The following is a set of procedures to ensure proper use of the Alert Tag.
To use the Alert Tag:
1.
For general use, place the strap of the Alert Tag around the person’s neck.
2.
In case of emergency press the large press button.
Battery Replacement
The battery is located inside the Alert Tag. In order to replace the battery, you need
to open the back side of the Alert Tag with a Phillips screwdriver (preferably an
electric one) with point size "0". For example, the APEX #4910. A new battery can
then be inserted, after which the screw must be replaced.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2000:08:17 07:14:56
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2000:08:17 07:14:58-04:00
Page Count                      : 4

EXIF Metadata provided by EXIF.tools