Elpas Solutions B07 User Manual users manual

Elpas Solutions Ltd. users manual

users manual

Baby Tag Instruction Manual and Spec-SheetFCC ComplianceThe FCC Wants You to KnowThis equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of theFCC rules. These limits are designed to provide reasonableprotection against harmful interference in a residentialinstallation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there is noguarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interferenceto radio or television reception, which can be determined bytuning the equipment off and on, the user is encouraged to tryto correct the interference by one or more of the followingmeasures:a) Reorient or relocate the receiving antenna.b) Increase the separation between the equipmentand receiver.c) Connect the equipment to an outlet on a circuitdifferent from that to which the receiver isconnected.d) Consult the dealer or an experienced radio/TVtechnician.FCC WarningModifications not expressly approved by manufacturer couldvoid the user authority to operate the equipment under FCCrules.IR and RF Baby TagP/N: BKB00001 (433.92 MHz)Baby Tag
DescriptionA small tag, attachable to a baby’s ankle, capable of transmitting Infra Red signals inaddition to RF signals in the frequency of 433.92 MHz. The tag is used for securitymonitoring (abduction and mismatch prevention) of infants whereabouts in real time,in hospitals’ Maternity Wards. The tag sends a unique message when the ankle bandhas been tampered with and disconnected.Recommended use is with the ELPAS BabyWatch system.GeneralElectrical powersource One 3-Volt lithium batteryBattery type CR 2032 RenataTransmissionrate A. Every 1.6 seconds, when the tag is in normaloperation mode - i.e. affixed to a baby. (IR istransmitted on every 3rd RF transmission, and RF istransmitted 200ms after IR).B. Every 60 seconds (RF), when the tag is not affixed toa baby, and is motionless.C. Every 4 seconds (200 ms apart), when the tag is notaffixed to a baby, but is in motion.D. Four times every 0.4 seconds, immediately aftertampering, or after affixing to baby (B2 indicates thatthe band is either on or off). Then, as either B or C,depending on mode of operation.Battery life In regular use, battery life will be approximately threemonths, based on a combination of A,B,C:A. Six weeks when the tag is affixed to a baby.B. Over three years when the tag is not affixed to a babyand is motionless.C. Six weeks when the tag is not affixed to a baby, butthe tag is in constant motion.LED indicatoron badge Activated with every RF and IR messageTag ID Unique factory-programmed (ID code, transmit rate,motion sensor activation and deactivation, etc.)Data rate 19,200 bits per secondMessageprotocol 4 bytes proprietary formatMessageduration 2.08 msDimensions 39.4 x 31.5 x 14.8 mmTag re-usability After each use, the baby tag needs to be cleaned andprepared for next use using the Baby Tag disposable kit’scontents. The tag can be re-used up to 100 times (this issolely because of connector restrictions).
Tag’sDisposablecomponents • Light green snap-on cover • Disposable band • White connector • Assembly set • Insulator • StickerWeight (whenassembled) 20 gramTemperature:Operating -10 to 70°CTemperature:Storage -20 to 60°CWaterresistance WaterproofAccessories Baby Tag Disposable Kit P/N BKB09001IR TransmissionPeak opticaltransmittedpower500mWPeaktransmissionwavelength880nmPeak radiantintensity 120 mW/SrFrequency oftransmission Carrier at 455 KHzTransmissionangle 360° badge plane. ±60° to badge perpendicular axisRF Transmission433.92 MHz RFModulation ASK (Amplitude Shift Keying of 433.92 MHz carrier)Averageeffectiveradiated powerIn motion: less than –35 dbm. Motionless: less than –45 dbmStability +/- 20ppmPeak ERP -15 dbm (max)Transmissionpattern OmnidirectionalFCC compliance FCC Part 15.231 Level CI-ETS EE 300 220-1
Using the Baby TagThe following is a set of procedures to ensure proper use of the Baby Tag.To use the Baby Tag:1. Place the Baby Tag band around the baby's ankle.2. Gently pull at both loose ends of wire until the strap is well wrapped (but nottightened) around the baby’s ankle.3. Hold the Baby Tag using two fingers of one hand, ensuring that the activatingset, comprising of the thumbscrew and hook, is held straight.4. Close the thumbscrew.5. Rotate the thumbscrew in a counterclockwise direction, as if closing a watertap, until the lamp on the wall is switched on displaying a green light.6. Cut excess loose wires.7. Open the thumbscrew slightly and remove the activating set.8. Align the wire in the loop on the back of the tag, and snap the tag’s over ontothe tag.

Navigation menu