Embed ICR001 Insert Card Reader Color Glo User Manual Embed AIO v5

Download:
Mirror Download [FCC.gov]
Document ID	2444937
Application ID	62vV7b/fP3WjZy4DQqHGcg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	96.35kB (1204415 bits)
Date Submitted	2014-11-14 00:00:00
Date Available	2014-11-14 00:00:00
Creation Date	2014-10-24 08:28:58
Producing Software	Microsoft® Word 2013
Document Lastmod	2014-11-11 16:47:18
Document Title	Embed AIO v5 User Manual
Document Creator	Microsoft® Word 2013
Document Author:	Damien Wieman

Insert Card Reader Color Glo
Service Mode User Manual
Model: ICR-001
Manual version: V1.0
Last amended 15 October, 2014
Copyright © 2014 by Embed International
Notice of Rights
All rights reserved. No part of this document may be reproduced or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior
written permission of Embed. For more information on getting permission for reprints and
excerpts, contact Embed.
Notice of Liability
The information in this document is distributed on an “as is” basis, without warranty. While
every precaution has been taken in the preparation of this document, neither the author or
Embed shall have any liability to any person or entity with respect to any loss or damage
caused or alleged to be caused directly or indirectly by the instructions contained in this
document or by the computer software or hardware products described herein.
www.embedcard.com
Embed USA
Embed International
Suite 100A
1621 West Crosby Rd
Carrolton, TX, 75006
94 Howe St
Osborne Park, WA, 6017
Australia
Telephone: +1 (469) 521 8000
Facsimile: +1 (214) 260 0976
Telephone: +61 (08) 9340 0100
Facsimile: +61 (08) 9340 0199
Information: info@embedcard.com
Sales: sales@embedcard.com
Support: USAsupport@embedcard.com
Information: info@embed.com.au
Sales: sales@embed.com.au
Support: support@embed.com.au
www.embedcard.com
Contents
LIST OF ACRONYMS ................................................................................................................ 3
SAFETY INFORMATION .......................................................................................................... 3
PROTECTING AGAINST ELECTROSTATIC DISCHARGE ............................................................................. 3
POWER SUPPLY DETAILS RANGE .......................................................................................................... 3
OTHER INFORMATION AND WARNINGS: ................................................................................................ 3
PRODUCT OVERVIEW: ............................................................................................................ 4
RECOMMENDED INSTALLATION HARDWARE ........................................................................................ 5
PRE-INSTALLATION ................................................................................................................. 6
ICR INSTALLATION .................................................................................................................. 7
NETWORK INTERFACE .......................................................................................................................... 9
CE – DECLARATION OF CONFORMITY............................................................................ 12
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) STATEMENT ..... 13
www.embedcard.com
1 List of Acronyms
Acronym
Description
ICR
Insert Card Reader
USB
Universal Serial Bus
Wi-Fi
Wireless Fidelity / IEEE 802.11b Direct Sequence
AC
Alternating Current
DC
Direct Current
2 Safety Information
This guide assumes that the installer is qualified to work on electrical devices, with
electronic skills and experience working with arcade machines.
Do not use in life critical or applications requiring high reliability
The Insert Card Reader is not intended for use in systems that may affect human life
or that require a very high degree of reliability such as medical equipment, nuclear
facilities, aerospace equipment or transportation equipment. Embed does not
assume any liability for accidents resulting in injury or death, or for any damages to
property that may occur as a result of using the product in such facilities, equipment,
or control systems.
Protecting against electrostatic discharge
Electrostatic discharge can damage electronic components including the
Embed Insert Card Reader. Please observe electrostatic discharge
precautions for handling or installing this equipment.
Power Supply Details Range
In some markets the Insert Reader includes a recommended universal
power supply requiring mains input of 100-240VAC, 50/60Hz, 0.5A.
Other information and warnings:


Embed Insert Card Reader is intended for operation between 55 0C and -20
C (131 0F and -4 OF).
Embed Insert Reader is not intended for domestic use.
www.embedcard.com
3 Product Overview:
The ICR is a facing device that features a touchscreen display and is capable of
accepting both traditional magnetic and contactless type cards. Guests insert their card
and interact with the touchscreen for the primary purpose of transacting at games and
attractions.
The device can be mounted in portrait or landscape orientations to best suited the
game and guest accessibility.
Communications with external hardware and servers is accomplished via a connector
on the underside of the ICR which has provision for power and data via unshielded
twisted pair/USB.
www.embedcard.com
Recommended Installation Hardware
The following is a recommended range of hardware to securely install and mount the
ICR. The ICR uses 4mm brass inserts in the base of the enclosure so the appropriate
length 4mm metric screws must be used to properly secure the ICR. All other
hardware can be adjusted to what is most appropriate and available in your area.
M4 metric, pan head, Philips drive, and zinc coated steel screws.
 Used to secure the ICR to the surface of the game or attraction.
 Recommended you have lengths of 10mm, 20mm and 25mm available as
a minimum.
M4 metric, zinc coated steel washers.
 Recommended these are used under every screw.
www.embedcard.com
4
Pre-Installation
Before the installation of any hardware, verify the following:
 An adequate earth connection point exists in the game cabinet.
 If the mounting surface is metal, that it is adequately earthed.
 The game credits when a coin is inserted
 The game accurately dispenses tickets
 The coin and ticket meters increment correctly
 Correct any identified faults and retest
 Disconnect the power from the game
It is vital that you are certain the game is in proper working order before beginning
the installation of the Embed hardware. This will prevent confusion later in the
process.
Never source and use wire taps or wire nuts. Wire taps cut into the wire and make a
minimal connection that will deteriorate over time leading to game credit and power
supply related problems. Wire nuts also offer a less-than-desirable connection on the
small gauge wire used in games.
Wire Tap
Wire Nut
Butt Connector
We recommends that crimp type butt connectors be used for wire joins and splicing.
You will need some tools and hardware for the equipment installation and
recommend the following as a minimum.





Multi-meter
Drill
5 mm drill bit
Step drill bit up to 20mm
Phillips screwdriver
www.embedcard.com




Wire stripper
Crimp tool for connectors
Butt connectors
Cable ties
5
ICR Installation
The ICR is best mounted and fixed to a location on the game that ensures it’s easily
accessible to guests. In many cases it’s recommended to mount the ICR over the
existing coin entry point as it is readily accessible and allows use of the existing hole
for cable entry.
The ICR display can be adjusted to accommodate a horizontal (with left or right card
entry) or vertical orientation. The default setting for the display orientation is vertical.
Horizontal/Landscape Orientation
Vertical/Portrait Orientation
Step 1: Locate the ideal position to mount the ICR.
Step 2: Mark the spots for drilling. Use the ICR mounting template to mark the four
mounting points and the cable connection point.
Step 3: Drill the four mounting points with a 5mm drill-bit. Drill the ICR to IOC
Interface Harness connection hole with a 12.5mm step drill-bit. Clear the holes of
sharp edges to protect the harness.
Step 4: Connect the ICR to IOC Interface harness to the connector in the bottom of
the ICR. Feed this through the hole in the cabinet and position the ICR to line up with
the screw mounting holes. Insert the correct length 4mm screws into the base of the
ICR and tighten.
Step 5: If the mounting surface is metal such as coin door, ensure there is an
adequate earth connection in place. Install an extra earth connection if necessary
using earth wire and a ring terminal secured under one of the ICR mounting screws.
Be sure to remove any surface coating as required to guarantee an adequate
electrical connection.
www.embedcard.com
Template for the ICR mount point drill holes. NOT TO 1:1 SCALE
This template is available in scale PDF format
www.embedcard.com
Network Interface
The ICR interfaces to a network server in a number of ways and this will generally be
determined by the client system.
Via an IO Controller:
At the top of the IOC is a USB port, this accepts an optional Ethernet Dongle for
cabled connections or a Wi-Fi dongle for wireless 802.11N (Wireless support is
pending).
Configuration of the network devices is done through the ICR service menu.
Via a Data-Port Controller
If used with a Data-Port Controller, the interface is purely USB. The ICR is
configured from the Data-Port Controller and the Data-Port Controller is responsible
for communicating with the system server.
Via Dongle
The ICR can be configured to communicate directly through a Wi-Fi or Ethernet
dongle via a modified harness.
www.embedcard.com
Network Configuration
Configure the network settings by following these steps
1. Press and hold the service button on the harness connected to access the
“Service Mode”.
2. Select the following buttons, Configure -> Network Settings
3. Using the touchscreen configure the settings as advised by your system
administrator.
NOTE: Support for Wi-Fi related setting such as SSID, Security is pending final
development and release.
www.embedcard.com
10
6 CE – Declaration of Conformity
According to ISO/IEC Guide 22 and EN????
Manufacturer Name:
Embed International
Manufacturer’s Address:
2 Neil Street
Osborne Park
Western Australia, 6017
Declares that the product (s):
Product Name:
Embed Insert Reader
Product Options:
All
Conforms to the following Product Specifications:
EMC:
Fulfils the essential requirements of the R&TTE directive 1999/5/EC as attested by conformity
with the following harmonized standards:
Health & Safety -
ETSI EN 60950-1
: 2006+A11 :2009+A12
:2011+A1 : 2010+AC :2011
ETSI EN 62311:2008 MPE
EMC
ETSI EN 301 489-17 v2.2.1
Radio
ETSI EN 300 440-1
ETSI EN 300 440-2
The conformity assessment procedure referred to in Article 10.4 and Annex III of Directive
1999/5/EC has been followed.
In addition, complies with Low Voltage Directive 2006/95/EC.
Supplementary Information:
The product(s) herewith comply with the requirements of the EMC Directive
2006/95/EEC. The product(s) were tested in a typical configuration.
Date:
1 April 2014
Mark Easte
Managing Director
www.embedcard.com
12
7 Waste Electrical and Electronic Equipment (WEEE)
Statement
Embed complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT
AND OF THE COUNCIL of 27 January 2003 on waste electrical and electronic
equipment (WEEE).
This product has required the extraction and use of natural resources for its production. It
may contain hazardous substances that could impact health and the environment, if not
properly disposed. In order to avoid dissemination of those substances in our environment
and to diminish the pressure on the natural resources, we encourage you to use the
appropriate take-back systems for product disposal. Those systems will reuse or recycle
most of the materials of the product you are dispensing in a sound way.
For proper disposal instructions go to,
http://www.embedcard.com/recycle
For more information about the disposal of Waste electrical and
Electronic Equipment (WEEE), please go to,
http://ec.europa.eu/environment/waste/weee/index_en.htm
Please retain this for future reference.
www.embedcard.com
13
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Tagged PDF                      : Yes
XMP Toolkit                     : 3.1-702
Create Date                     : 2014:10:24 08:28:58+08:00
Creator Tool                    : Microsoft® Word 2013
Modify Date                     : 2014:11:11 16:47:18+08:00
Metadata Date                   : 2014:11:11 16:47:18+08:00
Format                          : application/pdf
Creator                         : Damien Wieman
Title                           : Embed AIO v5 User Manual
Producer                        : Microsoft® Word 2013
Document ID                     : uuid:6525bf7a-fd92-451e-9197-7204ceb69bbf
Instance ID                     : uuid:a3eaedcc-8000-4d8e-8ca0-413d17b378aa
Has XFA                         : No
Page Count                      : 14
Language                        : en-AU
Author                          : Damien Wieman

EXIF Metadata provided by EXIF.tools