Embertec RD01SENSOR Smart Sensor User Manual Rev01 1009

Embertec Pty Ltd Smart Sensor Rev01 1009

User Manual Rev01-1009

ESUSAV8-ET-10D (DISH)
User manual
PATENTS GRANTED AND PATENTS PENDING V5
Quick connection guide
Se
t
ting
up
the
Embertec
Ember
s
trip
8
AV
+
1.
Plug AV equipment that can automatically be switched off into
the Power Saving outlets on the strip (TV, Blu-ray, DVD, speakers,
amplifier/stereo receiver).
2.
Identify equipment that requires constant power for cool down
period, timers, program guides and recording features, and plug
into the outlets marked Always On, or into another wall outlet
(e.g. DVR, cable/hard drives/gaming etc.).
3.
Place the RF4CE Smart Sensor in a convenient location, close to
your television is the best position and within normal operation of
your existing remote control(s). The RF4CE Smart Sensor detects
use of any of your remote controls to know when you are using
your AV equipment.
4.
P
lu
g t
he
E
m
b
er
t
e
c E
m
b
ers
t
ri
p
®
8A
V
+
in
to t
he
wa
ll
o
u
t
le
t
.
P
ow
er
is
now applied to the Power Saving outlets. The 1, 2 and M buttons
on the RF4CE Smart Sensor will flash for up to 5 seconds. Once
t
he
y
s
top
f
lashin
g t
his
in
d
i
c
at
es
t
h
at
t
he
E
m
b
er
t
e
c E
m
b
ers
t
ri
p
®
has
performed its initialization process and is ready.
2
NOTE: Other appliances such as lamps, chargers etc., may be
plugged into the Always On outlets if needed, or the Power
Saving outlets if only needed when your AV system is being used.
Quick operation guide
Turning ON your AV equipment
•
To operate your Audio Visual (AV) components, press the volume
button on any existing remote control. This will apply power to all
components making them ready for use. Now use your existing
remote(s) to operate your television or other Audio Visual (AV)
components in the normal way.
Turning OFF your AV equipment
•
Simply turn your equipment off in the normal way. The Embertec
Emberstrip® 8AV+ will then remove power from the Power Saving
outlets after a delay of approximately
1
minute.
Active Powerdown®
•
If your Embertec Emberstrip® 8AV+ has not detected use of a remote
control for 1, 2 or 8 hours (depending on your settings), Active
Powerdown® will shut down power. The LED light on the RF4CE
Smart Sensor will flash for approximately 10 minutes to warn you.
A flashing light means
the system is getting
ready to shut down.
TO CONTINUE
USING YOUR
EQUIPMENT
Press the volume
button on your
remote control.
NOTE: To reactivate your TV components, you may be required
to press the power button again on the relevant remote
control after power has been restored. You may hear a ‘click’,
or notice that the TV standby light has switched on.
NOTE: The LED light on the RF4CE Smart Sensor will flash
for about 60 seconds to warn you that power is about to be
removed from the AV Power Saving outlets.
3
Contents
Quick connection guide 2
Quick operation guide 3
Using your Audio Visual equipment 6
w
i
t
h
t
he
E
mber
t
e
c E
mber
s
t
ri
p
®
8
A
V
+
What you need to know 7
RF4CE Smart Sensor Setup 9
MusicMode™ settings 11
BedroomMode™ settings 12
Fast facts 13
Specifications and compliance 14
Troubleshooting guide 16
Warranty 17
4
Y
ou
r
Embert
e
c
Ember
s
trip
®
8
A
V
+
1.
Embertec Emberstrip® 8AV+
2.
RF4CE Smart Sensor (Model:RD-01)
3.
On/Off Power Saving
outlets indicator light
4.
Power Saving outlets
5.
Always On outlets
6.
Overload protection
Reset Button
7.
Surge protection light
5
Always On outlets
The Always On outlets are recommended for use with Audio Visual
(AV) equipment that requires constant power for timers, program
guide and recording features (e.g. DVR, PVR, VCR, cable box, digital TV
receivers, game consoles, hard drives or bedside alarms). This also
includes certain home theater projectors that require a cool down
period, including rear projection televisions. This will ensure constant
power is not interrupted to these devices.
Power Saving outlets – will be automatically switched off
The Power Saving outlets are recommended for Audio Visual (AV)
equipment that can be automatically switched off (e.g. televisions
without hard drives, amplifiers, stereos, speakers, sound bars, DVDs,
CDs, Blu-ray players, lamps).
RF4CE Smart Sensor (Model:RD-01)
The RF4CE Smart Sensor activates the Power Saving outlets,
monitors activity and is also used to set the Active Powerdown®. It
comes with a 9.8 ft/3 m cable, LED light and two button control.
Status lights
The Protected light should be on. If this light turns off or is dim, you
may have a ground-wiring problem in your home and you should
contact an electrician to properly ground the outlet.
The Power Saving Outlets On light shows the state of the Power Saving
outlets. When the light is on, the Power Saving outlets are powered; if
the light is off, no power is applied to the Power Saving outlets.
Other features
•
Overload protection circuit breaker reset button.
•
3 pins for use with standard North American wall outlets.
6
Using your Audio Visual equipment with the
Embertec Emberstrip® 8AV+
What you need to know
Please read this instruction booklet before installing
your Embertec Emberstrip® 8AV+
•
T
he
Embertec
Ember
s
trip
®
8A
V+
is
an
electrical
de
vic
e
.
Normal
safety precautions for use of an electrical device must be observed.
•
Do not immerse the Embertec Emberstrip® 8AV+ in water.
•
Needles, knives or any other metal or conductive item must not be
inserted into any Embertec Emberstrip® 8AV+ outlets.
•
This device does not convert voltage. It must only be used with
appliances fitted with North American configuration electrical plugs
(2-pin or 3-pin) and rated at 110 – 120 V AC.
•
Ensure
the
Embertec
Ember
s
trip
®
8
AV
+
is
secur
ely
plugged
in
to
the
wall outlet to avoid it slipping out. Ensure cords plugged into the
Embertec Emberstrip® 8AV+ remain tangle free.
•
It is recommended to regularly inspect the Embertec Emberstrip® 8AV+
for damage. The Embertec Emberstrip® 8AV+ must not be used if it
shows any signs of damage.
•
This Embertec Emberstrip® 8AV+ is for indoor use only. Do not use
outdoors. Do not use this Embertec Emberstrip® 8AV+ for anything
other than its intended use. Misuse may cause injury or death.
•
In normal use, this device intermittently emits a green flashing light.
People who experience photosensitive epilepsy or other forms of
photosensitivity should exercise caution when using the device.
•
The outlet on the side of your Embertec Emberstrip® 8AV+ (called
an RJ11 outlet) is for connection of your RF4CE Smart Sensor only.
It is NOT for connection of a phone, LAN communication device or
any other equipment.
7
We recommend connecting any home theater media center computers,
or appliances containing a hard drive into the Always On outlets. We
recommend connecting home theater projection equipment which
require a cool down period to the Always On outlets. This will prevent
damage to, and extend the life of your home theater projection lamps.
Embertec Emberstrip® 8AV+ has 2 power saving functions
1.
Standby Powerdown automatically detects and saves power
wasted when equipment is left in standby mode, by switching the
power off to the equipment.
2.
Active Powerdown® automatically switches the power off to Audio
Visual (AV) equipment connected to the Power Saving outlets
after
1
hour, if it has not detected any remote control use.
When will Active Powerdown® switch the Audio Visual (AV)
equipment off?
•
If your Embertec Emberstrip® 8AV+ detects that your Audio Visual (AV)
equipment is on but has not been used for a period of 1, 2 or 8 hours
(depending on your settings), the LED light on the RF4CE Smart
Sensor will flash for approximately 10 minutes to warn you that
power down is imminent.
To continue using your equipment
•
Simply press the volume button on ANY of your existing remote controls
or press any button on the RF4CE Smart Sensor. This will cancel the
Active Powerdown® and reset the timer.
A flashing light means
the system is getting
ready to shut down.
TO CONTINUE
USING YOUR
EQUIPMENT
Press the volume
button on your
remote control.
8
NOTE: A flashing LED always means that your system will shut
down completely in a while. Press any remote control button to
stop the light flashing and continue using your system.
NOTE: The Embertec Emberstrip® 8AV+ is programmable and
has an Active Powerdown® default setting of
1
hour, which can be
permanently set to 2 hours, or temporarily 8 hours (MusicMode™).
RF4CE Smart Sensor setup
The following explains how to pair/un-pair an RF4CE Smart Sensor
(Model:RD01) with your DISH remote:
1.
Turn your TV off.
2.
Pair your DISH remote (in RF mode) with your set top box.
3.
Your DISH remote has built in RF4CE capability. To enable your
infra-red (IR) capability, navigate to the IR section of your DISH
set top box.
4.
To ensure compatibility with your TV, select your TV model from
your DISH configuration menu.
5.
To “pair” the RF4CE Smart Sensor to your DISH remote, ensure
that your set top box is powered on.
6.
Press and hold the Music Mode button on the RF4CE Smart
Sensor (the “M” on top of the sensor) for 5 seconds, until the
sensor’s front LED light flashes once
7.
After 5-10 seconds the sensor’s LED will start to pulse. This
indicates that the RF4CE Smart Sensor is now ready to pair with
your DISH remote control.
8.
Now press the “SAT” button on your DISH remote. This will
activate RF mode.
9.
While the sensor’s LED is flashing, press and hold any button
on your DISH remote control (e.g. “search” or “menu”) until the
sensor’s LED stops flashing.
10.
Once the sensor’s LED stops flashing, the pairing process
is complete.
To supply power to your TV, simply use the volume or mute buttons
on your DISH remote control. This will send power to your entire AV
system. Then use your DISH remote control normally.
9
Changin
g
se
t
ting
s
f
o
r
A
ctiv
e
P
o
w
er
do
wn
®
Y
our
Embertec
Ember
s
trip
®
8
AV
+
is
equipped
with
a
number
of
se
t
tings
to suit your lifestyle. You can set your timer to either
1
or 2 hours,
depending on usage habits. This means the RF4CE Smart Sensor will
flash after the set period, warning of imminent power down. In every
case you can continue using your equipment by pressing the volume
button on any remote control.
The default setting is
1
hour, which is aimed to maximize your home’s
energy savings.
Follow these instructions to change Active Powerdown® to 2 hours,
(this may be preferred for longer movies or programs where remote
control activity is less frequent).
To set the Active Powerdown® timer, simply press the SET button on
top of the sensor.
The
1
and 2 LED lights on top of the sensor will light up to show the
current setting. Push the SET button to toggle between the
1
hour
and 2 hour Active Powerdown® settings.
10
NOTE: Make sure your AV System is on before you start changing settings!
MusicMode™ settings
Y
our
Embertec
Ember
s
trip
®
8A
V+
is
equipped
with
a
unique
MusicMode™
feature. This feature enables you to override the Active Powerdown®
for a period of 8 hours. This feature is great for playing music, parties,
video nights or any time you want to keep your appliances on for an
extended period of time.
T
he
Embertec
Ember
s
trip
®
8A
V+
will
re
v
ert
to
its
pr
e
vious
se
t
ting
of
1
or 2 hours after the 8 hour period elapses, or you switch your
appliances off.
Remember
1.
In this mode your system will stay on for 8 hours, unless you switch
your appliances off.
2.
Your permanent Active Powerdown® timer setting will revert to
1
or 2 hours once you have switched your appliances off, or after
8 hours, whichever comes first.
Ensure your Audio Visual (AV) equipment is switched on.
To set the Active Powerdown timer to MusicMode™ (8 hours), simply
press the MUSIC button on top of the sensor. The M LED will light
up to show that MusicMode™ is currently selected.
11
NOTE: Make sure your AV System is on before you start changing settings!
BedroomMode™ settings
Your RF4CE Smart Sensor is equipped with a unique feature which
enables you to reduce the brightness of the RF4CE Smart Sensor
‘flash’ and to reduce the length of flashing when your equipment is
no longer being used.
Your device is shipped with the brightness level set to maximum,
however you may wish to enable BedroomMode™ to reduce
the brightness of the RF4CE Smart Sensor light in a bedroom.
BedroomMode™ is not recommended for living rooms or brightly
lit areas.
To set bedroom mode using the RF4CE Smart Sensor:
Make sure that at least your TV is switched on before starting.
1.
Press and hold the SET button on the RF4CE Smart Sensor for
3 seconds then release. The LED light on the front of the sensor will
flash, starting from a faint flash slowly progressing to a bright flash.
2.
When you are happy with the level of brightness, press the SET
button on the RF4CE Smart Sensor again.
3.
You can change the brightness of the RF4CE Smart Sensor at any
time by following the above steps.
12
NOTE: When BedroomMode™ is selected, the RF4CE Smart Sensor
will flash for 10 seconds once the television is turned off. Power
will be cut to the power saving outlets after another 50 seconds.
To adjust the RF4CE Smart Sensor to flash for one minute, press
the MUSIC button instead of the SET button at step 2.
Fast facts
Specifications
•
Surge protection is provided to all outlets. Conforms with UL 1449
and UL 1363.
•
Senses total power being consumed by all controlled devices.
•
Senses Infrared (IR), RF4CE (RF) and true Root Mean Squared (RMS)
power to determine device usage of AV equipment.
•
Hardware IR filtering technology and firmware to filter out rogue
non AV equipment IR interference from compact fluorescent lights
and sunlight.
•
Automatically adjusts power switching threshold.
What power is wasted?
Many of today’s appliances for the home and office continue to use
power, even when the appliance is turned off. Appliances that are left
on unintentionally waste even more power.
Overload protection
T
he
Embertec
Ember
s
trip
®
8A
V+
is
fit
t
ed
with
a
safe
ty
de
vic
e
tha
t
removes power in the event of overloading. Should this occur, turn
off and unplug all units, and press the reset button. Then plug into
the wall outlet again. Once reset, use any remote control to activate
power to the Power Saving outlets. Connect one device at a time. If
any of the devices cause the safety device to trip again then get the
offending
de
vic
e
servic
ed.
If
the
Embertec
Ember
s
trip
®
8A
V+
f
ails
to
operate, please contact Embertec on 1-800-838-9659.
Care and maintenance
T
o
clean
the
outside
of
the
Embertec
Ember
s
trip
®
8A
V+
de
vic
e
,
firs
t
remove the device from the power point. Then wipe the exterior with
a soft dry cloth. Never use an abrasive cleaner or water.
Disposal/recycling
T
o
pr
ot
ec
t
the
en
vironmen
t,
the
Embertec
Ember
s
trip
®
8A
V+
should
be recycled, or disposed of safely at the end of its life. Please return to
a recycling center for safe recycling or disposal.
13
Electrical specifications
Physical
Dimensions:
16.54 in L x 2.72 in W x 1.57 in D
(420 mm L x 69 mm W x 40 mm D)
Weight:
1.78 lb (810 g)
Color:
Black body
RF4CE Smart Sensor
Cable Length:
9.8 ft (3 m)
Power Cord Length:
4 ft (1.22 m)
Number of Outlets: 8
Always On: 2
Power Saving: 6
Environmental
Temperature (operating):
32 °F to +158 °F (0 °C to +70 °C)
Temperature (storage):
-4 °F to +185 °F (-20 °C to +85 °C)
Humidity (operating):
95% RH at +122 °F (+50 °C)
Protection and Safety
Total Surge:
1,974 Joules / 45,000 Amps for all outlets
Input Current:
15 Amps RMS via circuit breaker
Over-Current Threshold:
15 Amps RMS
Electrical Durability
Relay Endurance:
Over 100,000 switching cycles
Operating Voltage:
110 V AC +/- 10%
Maximum Output Current:
15 Amps RMS
Max Total Load:
1,800 W
Maximum Power Consumption
(In all modes of operation)
<
1
W
@ 110
V / 60 Hz
Control
RF4CE Smart Sensor Infrared Interface.
Does not rely on the use of a single device in an AV environment to supply
power to other devices.
Due to continual improvement in design or otherwise, the product you purchase may differ
slightly from the products shown in this information sheet.
14
Specifications
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between equipment and receiver
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any changes or modifications not expressly approved
by Embertec Pty Ltd could void the user’s authority to operate
this equipment.
FCC warning
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed and operated with minimum distance
20cm between the radiator & your body
IC warning
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Exposure to Radio Frequency Radiation:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
French:
Cet appareil radio est conforme au CNR d’Industrie Canada.
L’utilisation de ce dispositif est autorisée seulement aux deux
conditions suivantes : (1) il ne doit pas produire de brouillage, et
(2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage
radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
Exposition au rayonnement radioélectrique:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
5
Troubleshooting guide
Problem To check
The Embertec Emberstrip® 8AV+
is not receiving power.
•
The Protected light is on.
The Embertec Emberstrip® 8AV+
is not powering down my
equipment in standby mode.
•
Ensure the equipment is plugged into
the Power Saving outlets, not into the
Always On outlets.
•
The Embertec Emberstrip® 8AV+ has not
detected the equipment is in standby. Please
repeat this process by switching on the
Audio Visual (AV) component again, waiting
1
0
se
co
n
d
s
,
an
d
s
w
i
tc
hin
g o
ff
a
g
ain
m
akin
g
sure all appliances are in standby mode.
The RF4CE Smart Sensor
is not operating.
•
Remove the Embertec Emberstrip® 8AV+ from
the wall plug, then unplug the RF4CE Smart
Sensor cable and then plug it back into the
unit and plug the Embertec Emberstrip® 8AV+
back into the power point.
The RF4CE Smart Sensor
flashes frequently during
normal operation.
•
This may be an indication of unwanted infrared
activity in the area. Please check the immediate
area for infrared devices that maybe interfering
with the Embertec Emberstrip® 8AV+, such
as compact fluorescent lights, computers,
mobile phones, and other portable consumer
electronic devices. If possible relocate these
interfering devices.
•
Move the RF4CE Smart Sensor to another
location that is within line of sight and normal
operation range of your Audio Visual (AV)
equipment remote controls.
The Protected LED on the main
body of the Embertec Emberstrip®
8AV+ is on, but my RF4CE Smart
Sensor LED does not work (when
plugged in and powered on).
•
Please check your RF4CE Smart Sensor
connection to the Embertec Emberstrip® 8AV+
by ensuring the RF4CE Smart Sensor cable is
safely and securely connected to the side of
the Embertec Emberstrip® 8AV+.
The Embertec Emberstrip® 8AV+
has stopped working.
•
Unplug all the appliances connected into the
Embertec Emberstrip® 8AV+ adapter and then
unplug from the wall outlets. Then reconnect
everything again.
The TV keeps turning off
after
1
hour.
•
The RF4CE Smart Sensor default setting for
Active Powerdown® is 60 minutes.
•
Please see Changing settings for Active
P
ow
er
do
wn
®
to
change
A
ctiv
e
P
ow
er
do
wn®
to
1
or 2 hours.
16
Limited warranties
Our Embertec Emberstrip® is designed and manufactured with precision and care, which
is why we offer a Limited Product Warranty and a Limited $25,000 Connected Equipment
Warranty for each Embertec Emberstrip®.
LIMITED PRODUCT WARRANTY
What is covered?
Except as limited here, this product warranty covers any defect in material or workmanship
with the Embertec Emberstrip®. If the initial purchase is by a utility or other entity that will
not itself be using the device, this warranty is transferable to any customer of such entity
who subsequently owns the device. Otherwise, this warranty is not transferable.
For how long?
This warranty runs for the lifetime of the Embertec Emberstrip®. The lifetime of the
Embertec Emberstrip® is 15 years from the date of purchase.
What will we do if the device fails during the limited product warranty period and
this warranty applies?
Subject to the limitations set forth in this warranty, we will elect (at our option) to either
repair or replace the defective device. If we elect to replace the device and it has been
discontinued, we will replace it with another device of equal or greater value. We will ship
the repaired or replacement device to you, and pay for those shipping costs.
What does this limited product warranty not cover?
This warranty does not cover any damage to the Embertec Emberstrip® caused by improper
use, accidents, acts of God (such as lightning strikes, floods or earthquakes), or normal wear
and tear. For purposes of this warranty, “improper use” means not installing or operating the
device in accordance with the manual. Any incidental, consequential, special or other indirect
damages are not recoverable under this warranty. Some states do not allow the exclusion of
incidental or consequential damages, so the foregoing limitation may not apply to you. You
will be responsible for any shipping or other transportation costs incurred in connection with
returning the defective product to us.
How do you request service under this limited product warranty?
To request service under this warranty for your Embertec Emberstrip®, (i) visit embertec.com
for our address or a list of authorized service providers near you, and (ii) either pack the
product carefully to prevent damage in transit and ship it, along with a brief description of
the defect, to our address, or bring it into one of our authorized service providers.
This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
LIMITED $25,000 CONNECTED EQUIPMENT WARRANTY
What is covered?
Except as limited here, this connected equipment warranty covers any equipment that is
damaged by a transient voltage surge or spike (an “Occurrence”) while properly connected
to an Embertec Emberstrip® that is properly connected to an AC power line with a protective
ground. If the initial purchase of the Embertec Emberstrip® is by a utility or other entity that
will not itself be using the device, this warranty is transferable to any customer of such entity
who subsequently owns the device. Otherwise, this warranty is not transferable.
17
For how long?
This warranty runs for the lifetime of the Embertec Emberstrip®. The lifetime of the
Embertec Emberstrip® is 15 years from the date of purchase.
What will we do if connected equipment is damaged during the limited connected
equipment warranty period and this warranty applies?
Subject to the limitations set forth in this warranty, we will elect (at our option) to repair or
replace any equipment damaged by an Occurrence, or to pay you an amount equal to the
replacement value for such equipment, not to exceed the overall maximum set forth below.
In connection with the foregoing, we reserve the right to examine the damaged equipment
at the site where the damage occurred. If we elect to replace the equipment and it has
been discontinued, we will replace it with similar equipment of equal or greater value,
subject to the overall maximum set forth below. We will pay for all shipping costs incurred
in connection with the delivery of any repaired or replacement equipment to you, subject
to the overall maximum set forth below.
What does this limited connected equipment warranty not cover?
This limited connected equipment warranty does not cover:
•
Any damage to connected equipment caused by improper use of the Embertec Emberstrip®
or the connected equipment, accidents, acts of God (such as lightning strikes, floods or
earthquakes), or normal wear and tear of the Embertec Emberstrip® or the connected
equipment. For purposes of this warranty, “improper use” means not installing or
operating the Embertec Emberstrip® in accordance with the manual, or not installing or
operating the connected equipment in accordance with its manual.
•
Any damage to equipment that is not properly connected to an Embertec Emberstrip®,
or damage to equipment connected to an Embertec Emberstrip® that is not properly
connected to an AC power line with a protective ground.
•
Any damage to equipment connected to an Embertec Emberstrip® that had previously
experienced another Occurrence. After each Occurrence, the Embertec Emberstrip®
must be replaced.
•
Any damaged equipment that has been disposed before we have examined the
equipment at the site where the damage occurred (or notified you that we would not be
visiting the site), and elected whether to repair or replace it or pay for its replacement
value, all in accordance with the terms set forth above.
•
Any damage to satellite dishes.
THE MAXIMUM CUMULATIVE AMOUNT WE WILL PAY FOR ALL
REPAIRS, REPLACEMENT AND SHIPPING COSTS FOR ANY AND
ALL DAMAGED EQUIPMENT QUALIFYING UNDER THIS WARRANTY
SHALL NOT EXCEED TWENTY FIVE THOUSAND DOLLARS ($25,000).
Any incidental, consequential, special or other indirect damages are not recoverable
under this warranty. Some states do not allow the exclusion of incidental or consequential
damages, so the foregoing limitation may not apply to you.
If the connected equipment is covered by an applicable homeowner’s or renter’s insurance
policy, we reserve the right to be subrogated under such policy. In addition, this warranty
shall not apply to any damaged equipment covered under the manufacturer’s warranty.
How do you file a claim under this limited connected equipment warranty?
To file a claim for connected equipment qualifying under this warranty, visit embertec.com
or call 1-800-838-9659 and provide a full description of the damage.
This warranty gives you specific legal rights. You may also have other rights which vary
from state to state.
18
Important
Please retain your instruction book for future use.
In the event that you need assistance, please contact us on 1-800-838-9659
or email us at customerservice@embertec.com or, alternatively visit us
on our website at embertec.com
Except as required by law, Embertec is not responsible for special,
incidental, or consequential damages, or loss of data; or any loss or
damage arising from intentional misuse of the product. Such damages
and loss include, but are not limited to: lost business; business
downtime; component/equipment replacement and reconfiguration;
and the costs of retrieval of lost data.
Embertec, Emberstrip and the Embertec Empowered logo are trademarks
of Embertec Pty Ltd.
Embertec USA LLC
176 Seacliff Drive
Aptos, CA 95003
Phone: 1-800-838-9659
Web: embertec.com
Email: customerservice@embertec.com
Due to continual improvement in design or otherwise, the product
you purchase may differ slightly from the illustration in this book. Issue V3

Navigation menu