Emc Ds Xxb2 Users Manual Departmental Switch XxB2, Guide For Installation Of Switches Into Third Party Racks
DS-xxB2 to the manual b920dfa4-9a9a-4d70-ba17-4868140ac8b6
2015-02-06
: Emc Emc-Ds-Xxb2-Users-Manual-540062 emc-ds-xxb2-users-manual-540062 emc pdf
Open the PDF directly: View PDF 
.
Page Count: 22
| Download | |
| Open PDF In Browser | View PDF |
EMC Departmental Switch DS-xxB2 Guide for Installation of Switches Into Third-Party Racks P/N 300-000-267 Rev. A02 November 7, 2002 This document describes the requirements for installing EMC Deparmental Switches (DS-xxB2) into both EMC and non-EMC third-party racks. Major sections discussed in this guide are as follows: ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ Overview ................................................................................................2 Device Power, Cooling, and Weight Information .............................3 Device Dimensions................................................................................3 Device Placement Requirements.........................................................4 Switch Mounting Kit (DS16B2RKLS) .................................................5 Installing the DS-xxB2 Rails.................................................................8 Installing the DS-xxB2 Switch............................................................17 Where to Get Help...............................................................................21 1 Overview Overview The Departmental Switch Models DS-16B2 and DS-32B2 are fibre channel gigabit switches that support link speeds up to 2 Gb/s. Each port can automatically negotiate to the highest common speed of all devices connected to the port. The ports are compatible with small form factor pluggable media (SFPs), are universal, self configuring, and are capable of individually becoming a fabric-enabled port (F_Port), fabric loop enabled port (FL_Port), or an expansion port (E_Port). The Departmental Switch Model DS-16B2 is one rack unit in height, has an air-cooled chassis, and can be set up as a stand-alone unit or mounted in a 19-inch rack. The Departmental Switch Model DS-32B2 is an air-cooled 1.5U chassis; can be set up as a stand-alone unit or mounted in a standard Electronic Industries Association (EIA) 19-inch rack. Table 1 lists the departmental switches and mounting kit model numbers. Table 1 Departmental Switch and Mounting Kit Model Numbers. Device Device Model Mounting Kit Model 16-port Departmental Switch DS-16B2-00 DS16B2RKLS 32-port Departmental Switch DS-32B2-00 DS16B2RKLS Figure 1 shows an example of the DS-xxB2. EMC2041 Figure 1 2 DS-xxB2 EMC Departmental Switch DS-xxB2 Into Third-Party Racks Device Power, Cooling, and Weight Information Device Power, Cooling, and Weight Information Table 2 lists the power and cooling requirements and weight information for the DS-16B2 and DS32B2 switches. Table 2 Device Power, Cooling, and Weight Information Cooling Requirements (Heat Dissipation) Maximum Weight DS-16B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz 368.5 BTU/hr 12.9 kg (28.5 lbs) DS-32B2 switch Voltage: 100 to 240 V ac, 47 to 63 Hz 1876 BTU/hr 16.2 kg (35.8 lbs) Device Power Requirements Device Dimensions Table 3 gives the height, depth, and width for the DS-16B2 switch, the DS-16B2 switch with rails, and the DS-32B2 switch Table 3 Device Dimensions Device Height Depth Width DS-16B2 switch 4.34 cm 1.71 in 61.00 cm 24.01 in 42.86 cm 16.87 in DS-16B2 switch with rails 1.0 U 4.44 cm 1.75 in 61.00 cm 24.01 in 43.18 cm 17.00 in DS-32B2 switch 1.50 6.55 cm 2.58 in 58.56 cm 23.06 in 42.86 cm 16.87 in EMC Departmental Switch DS-xxB2 Into Third-Party Racks 3 Device Placement Requirements Device Placement Requirements There are no restrictions on the location of the DS-xxB2 switch in the rack/cabinet. Switches are typically located at the top of the rack/cabinet. Power distribution must support the number of outlets required for the switch and the switch power rating listed in Table 2 on page 3. Front Rear EMC2056S Figure 2 4 Sample Cabinet Installation EMC Departmental Switch DS-xxB2 Into Third-Party Racks Switch Mounting Kit (DS16B2RKLS) Switch Mounting Kit (DS16B2RKLS) The switch mounting kit includes rails, and brackets as listed inTable 4. Table 4 Switch Mounting Kit Component Use 2 switch mounting brackets (see Figure 15 on page 17) 2 per switch 2 short rail assemblies (20.5 inches to 27 inches) 2 per switch 2 long rail assemblies (27 inches to 34 inches) 2 per switch Figure 3 illustrates these components. Switch Mounting Brackets Short Rear Rails Front Rails Long Rear Rails EMC2042S Figure 3 Rails and Brackets EMC Departmental Switch DS-xxB2 Into Third-Party Racks 5 Switch Mounting Kit (DS16B2RKLS) Screws, Nuts and Washers Table 5 lists all the securing hardware that is included in the switch mounting kit. Table 5 Screws, Nuts and Washers Component 6 Use #10 flat washer (Qty. 4) 2 per rail assembly to secure adjustable rail to the “C” channel. M5 keps nut (Qty. 4) 2 per rail assembly to secure adjustable rail to the “C” channel. 8-32 x 5/16-in. pan-head screw (Qty. 6) 3 per mounting bracket to secure mounting bracket to switch. M5 x 10-mm pan-head screw (Qty. 8) 4 per rail for DS-16B2 in round-hole channels. Square-hole washer (Qty. 8) 4 per rail for DS-16B2 in square-hole channels. M5 x 16-mm flat-head screw (Qty. 8) 4 per rail for DS-16B2 in square-hole channels. M3 x 8-mm pan-head screw (Qty. 2) 1 per switch mounting bracket. Used to secure mounting brackets to the rails. EMC Departmental Switch DS-xxB2 Into Third-Party Racks Switch Mounting Kit (DS16B2RKLS) Tools Required for Installation You will need the tools shown in Figure 4 to complete the installation of the rails and one or more switches. Tools Required: #1 Phillips Screwdriver 6-mm (1/4-in.) Nut Driver 8mm (5/16-in.) Nut Driver EMC2065 Figure 4 Tools Required for Installation EMC Departmental Switch DS-xxB2 Into Third-Party Racks 7 Installing the DS-xxB2 Rails Installing the DS-xxB2 Rails This section describes the installation procedures for the DS-xxB2 rails. Figure 5 shows a view of the rails installed in a 39 U rack/cabinet. Rear Door Removed for Clarity Rear Front Figure 5 8 View of the Rails Installed in a 39 U Rack/Cabinet EMC Departmental Switch DS-xxB2 Into Third-Party Racks EMC2071S Installing the DS-xxB2 Rails DS-xxB2 Rails Installation There are two different length rails, see Figures 6 and 7. The short rails range between 20.5 inches and 27 inches. The long rails range between 27 inches and 34 inches. If your rail kit contains two different length rear rail mounts, be sure to use the rail length that is appropriate for your rack/cabinet. To the rear of the cabinet EMC2059 Figure 6 DS-xxB2 Short Rear Rails To the rear of the cabinet EMC2060 Figure 7 DS-xxB2 Long Rear Rails EMC Departmental Switch DS-xxB2 Into Third-Party Racks 9 Installing the DS-xxB2 Rails The front and rear flanges of the DS-xxB2 rails have three screw holes. See Figures 8 and 9. Front Rails Screw Holes Figure 8 EMC2069 Front Flange of the DS-xxB2 Rails Screw Holes Short Rear Rails Long Rear Rails Figure 9 10 Rear Flange of the DS-xxB2 Rails EMC Departmental Switch DS-xxB2 Into Third-Party Racks Screw Holes EMC2070 Installing the DS-xxB2 Rails Select the appropriate length rails, and follow the steps below to install them. The rails assembly consists of a front rail, an adjustable rear rail, and two washers and keps nuts. Figure 10 illusrates the complete assembly. Keps Nut (2) #10 Flat Washer (2) Short Rear Rail Front Rail Front Rail Figure 10 Short Rear Rail #10 Flat Washer (2) Keps Nut (2) EMC2044S DS-xxB2 Rails Assembly EMC Departmental Switch DS-xxB2 Into Third-Party Racks 11 Installing the DS-xxB2 Rails Assembling the Rails To assemble the rails: 1. Place the front rail down on a table. 2. Insert the slots of the rear adjustable rail onto the threaded posts on the front rail. Be sure that the lip on the top of the rear adjustable rail slides over the top of the slot on the front rail, thereby capturing the ac power cord. 3. Secure the adjustable rail to the front rail with two #10 flat washers and M5 keps nuts. Leave the keps nuts finger tight (see Figure 11). Keps Nut EMC2066S Figure 11 Location of Keps Nuts 4. Determine where in the rack/cabinet you will locate the switch. 5. Adjust the length of the rail to fit between the channels in the rack/cabinet. 12 EMC Departmental Switch DS-xxB2 Into Third-Party Racks Installing the DS-xxB2 Rails Keps Nut Keps Nut EMC2045S Figure 12 Securing the Keps Nuts If the side skins are removed on the rack/cabinet, the keps nuts can be tightened after the rails have been installed. Round-Hole Channel To install the rails assembly in the round-hole channel of the rack/cabinet: 1. Align the holes of the front rail flange to the inside of the front channel. The top and bottom screw holes are used for the screws. 2. Secure the rail to a round-hole channel with 2 M5 x 10-mm panhead screws (see table on Table 5 on page 6). Leave the screws finger-tight, and tighten them after the switch is installed. See Figure 13 on page 14. 3. Align the holes in the rear, U-shaped flange of the rail with the holes in the rear inside channel. 4. Secure the rail to a round-hole channel with 2 M5 x 10-mm panhead screws (see table on Table 5 on page 6). Leave the screws finger-tight, and tighten them after the switch is installed. See Figure 13. 5. Repeat steps 1 through 4 for the other rail. See instructions for Square-Hole Channel on page 15. EMC Departmental Switch DS-xxB2 Into Third-Party Racks 13 Installing the DS-xxB2 Rails Align the rear rail flange to the inside of the channel. Rack Rear Align the front rail flange to the inside of the channel. Rack Front Rear M5 x 10-mm Pan Head Screw (8) Front EMC2046S Figure 13 14 Installing Rails in Round-Hole Channels EMC Departmental Switch DS-xxB2 Into Third-Party Racks Installing the DS-xxB2 Rails Square-Hole Channel To install the rails assembly in the square-hole channel of the rack/cabinet. 1. Align the holes of the front rail flange to the inside of the front channel. The top and bottom screw holes are used for the screws (see Figure 14 on page 16). 2. Secure the rail to a square-hole channel with two square-hole washers and M5 x 16-mm flat-head screws (see Table 5 on page 6). Leave the screws finger-tight, and tighten them after the switch is installed. 3. Align the holes in the rear, U-shaped flange of the rail with the holes in the rear inside channel, as shown in Figure 14. 4. Secure the rail to a square-hole channel with two square-hole washers and M5 x 16-mm flat head screws (see Table 5 on page 6). Leave the screws finger-tight, and tighten them after the switch is installed. 5. Repeat steps 1 through 4 for the other rail. See instructions for Round-Hole Channel on page 13. EMC Departmental Switch DS-xxB2 Into Third-Party Racks 15 Installing the DS-xxB2 Rails Rack Rear Rack Front Align the rear rail flange to the inside of the channel. Align the front rail flange to the inside of the channel. M5 x 16-mm flat head screw (Qty. 8) Square-Hole Washer (Qty. 8) EMC2047S Figure 14 16 Installing Rails in Square-Hole Channels EMC Departmental Switch DS-xxB2 Into Third-Party Racks Installing the DS-xxB2 Switch Installing the DS-xxB2 Switch This section describes the procedures for installing the DS-xxB2 switch in a rack/cabinet, including attaching the brackets on the switch. Mounting Bracket Installation You must attach mounting brackets to the switch before installing it on the rails. The mounting brackets slide into the “C” channel of the rails. To attach the mounting brackets to the switch: 1. Orient the L-shaped end of the bracket outward and to the power outlet end of the switch. 2. Place the bracket against the switch. Align the three screw holes in the bracket with three screw holes on the side of the switch (see Figure 15 on page 17). 3. Secure the bracket with three 8-32 x 5/16-in. pan-head screws (see Table 5 on page 6). Tighten the screws fully. 4. Repeat steps 1 through 3 for the other side of the switch to be mounted. Switch Mounting Bracket #8-32 x 5/16-in. Pan Head Screw (6) Hole Switch Mounting Bracket Figure 15 EMC2048 Attaching the Switch Mounting Brackets EMC Departmental Switch DS-xxB2 Into Third-Party Racks 17 Installing the DS-xxB2 Switch Installing the Switch in the Rack/Cabinet To install the switch in the rack/cabinet: 1. Lift and orient the switch so that the fan end is to the front of the rack/cabinet. 2. Align the bracket on each side of the switch with the “C” channel on each fixed rail. 3. Push the switch into the rack/cabinet until the hole in the front part of each bracket (the “L”-shaped end) aligns with the hole on the fixed rail. EMC2049S Figure 16 Placing the Switch Into the Rack/Cabinet 4. Secure the brackets to the rails with two M3 x 8-mm pan-head screws (see Table 5 on page 6), one on each side, (Figure 17 on page 19). 18 EMC Departmental Switch DS-xxB2 Into Third-Party Racks Installing the DS-xxB2 Switch M3 x 8-mm Pan Head Screw (2) Figure 17 EMC2050S Securing the brackets to the Rails 5. Tighten the rear screws securing the rails to the rear of the rack/cabinet (see Figure 18 on page 20). 6. Tighten the front screws securing the rails to the front of the rack/cabinet (see Figure 18). EMC Departmental Switch DS-xxB2 Into Third-Party Racks 19 Installing the DS-xxB2 Switch Rail Assembly Screw (4) Rail Assembly Screw (4) Figure 18 20 Tightening the Front and Rear Rail Assembly Screws EMC Departmental Switch DS-xxB2 Into Third-Party Racks EMC2051S Where to Get Help Where to Get Help For questions about technical support call your local sales office or service provider. If you have a valid EMC service contract, contact EMC Customer Service at: United States: (800) 782-4362 (SVC-4EMC) Canada: (800) 543-4782 (543-4SVC) Worldwide: (508) 497-7901 Follow the voice menu prompts to open a service call and select the applicable product support. If you are located outside the North America, call the nearest EMC office for technical assistance. Sales and Customer Service Contacts For the list of EMC sales locations, please access the EMC home page at: http://www.EMC.com/contact/ For additional information on the EMC products and services available to customers and partners, refer to the EMC Powerlink website at: http://powerlink.EMC.com Your Comments Your suggestions will help us continue to improve the accuracy, organization, and overall quality of the user publications. Please send a message to techpub_comments@EMC.com with your opinions of this guide. EMC Departmental Switch DS-xxB2 Into Third-Party Racks 21 Where to Get Help Copyright © 2002 EMC Corporation. All Rights Reserved. EMC believes the information in this publication is accurate as of its publication date. The information is subject to change without notice. THE INFORMATION IN THIS PUBLICATION IS PROVIDED "AS IS." EMC CORPORATION MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WITH RESPECT TO THE INFORMATION IN THIS PUBLICATION, AND SPECIFICALLY DISCLAIMS IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Use, copying, and distribution of any EMC software described in this publication requires an applicable software license. 22 EMC Departmental Switch DS-xxB2 Into Third-Party Racks
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Modify Date : 2002:11:08 10:16:41-05:00 Create Date : 1995:06:29 12:54:00Z Creator : FrameMaker 6.0 Subject : P/N 300-000-267 Rev A02 Page Count : 22 Page Mode : UseOutlines Producer : Acrobat Distiller 4.05 for Windows Mod Date : 2002:11:08 10:16:41-05:00 Creation Date : 1995:06:29 12:54:00Z Metadata Date : 2002:11:08 10:16:41-05:00 Title : EMC Departmental Switch DS-xxB2, Guide for Installation of Switches Into Third-Party Racks Description : P/N 300-000-267 Rev A02EXIF Metadata provided by EXIF.tools