Emc Em78612 Users Manual EM78612_NEW V1.0_20060417_
EM78612 to the manual c78baeb3-25b8-4717-8c60-9ba020c976b4
2015-02-06
: Emc Emc-Em78612-Users-Manual-540038 emc-em78612-users-manual-540038 emc pdf
Open the PDF directly: View PDF 
.
Page Count: 37
| Download | |
| Open PDF In Browser | View PDF |
EM78612
Product
Specification
DOC. VERSION 1.0
ELAN MICROELECTRONICS CORP.
March 2006
Trademark Acknowledgments:
IBM is a registered trademark and PS/2 is a trademark of IBM.
Windows is a trademark of Microsoft Corporation.
ELAN and ELAN logo
are trademarks of ELAN Microelectronics Corporation.
Copyright © 2006 by ELAN Microelectronics Corporation
All Rights Reserved
Printed in Taiwan
The contents of in this specification are subject to change without notice. ELAN Microelectronics assumes no
responsibility concerning the accuracy, adequacy, or completeness of this specification. ELAN Microelectronics
makes no commitment to update, or to keep current the information and material contained in this specification.
Such information and material may change to conform to each confirmed order.
In no event shall ELAN Microelectronics be made responsible to any claims attributed to errors, omissions, or
other inaccuracies in the information or material contained in this specification. ELAN Microelectronics shall not
be liable for direct, indirect, special incidental, or consequential damages arising out of the use of such information
or material.
The software (if any) described in this specification is furnished under a license or nondisclosure agreement, and
may be used or copied only in accordance with the terms of such agreement.
ELAN Microelectronics products are not intended for use in life support appliances, devices, or systems. Use of
ELAN Microelectronics product in such applications is not supported and is prohibited.
NO PART OF THIS SPECIFICATION MAY BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY
ANY MEANS WITHOUT THE EXPRESS WRITTEN PERMISSION OF ELAN MICROELECTRONICS.
Headquarters:
Hong Kong:
USA:
No. 12, Innovation Road 1
Science-based Industrial Park
Hsinchu, Taiwan 308
Tel: +886 3 563-9977
Fax: +886 3 563-9966
http://www.emc.com.tw
Elan (HK) Microelectronics
Corporation, Ltd.
Elan Information Technology
Group
Rm. 1005B, 10/F Empire Centre
68 Mody Road, Tsimshatsui
Kowloon , HONG KONG
Tel: +852 2723-3376
Fax: +852 2723-7780
elanhk@emc.com.hk
1821 Saratoga Ave., Suite 250
Saratoga, CA 95070
USA
Tel: +1 408 366-8223
Fax: +1 408 366-8220
Europe:
Shenzhen:
Shanghai:
Elan Microelectronics Corp.
(Europe)
Elan Microelectronics
Shenzhen, Ltd.
Elan Microelectronics
Shanghai Corporation, Ltd.
Siewerdtstrasse 105
8050 Zurich, SWITZERLAND
Tel:+41 43 299-4060
Fax:+41 43 299-4079
http://www.elan-europe.com
SSMEC Bldg., 3F, Gaoxin S. Ave.
Shenzhen Hi-Tech Industrial Park
Shenzhen, Guandong, CHINA
Tel: +86 755 2601-0565
Fax: +86 755 2601-0500
23/Bldg. #115 Lane 572, Bibo Road
Zhangjiang Hi-Tech Park
Shanghai, CHINA
Tel: +86 021 5080-3866
Fax: +86 021 5080-4600
EM78612
Universal Serial Bus Microcontroller
1 General Description·················································································· 4
2 Features··································································································· 4
3 Applications ··············································································································· 5
4 Pin Configuration ····································································································· 6
5 Pin Description ········································································································· 7
6 Function Block Diagram ························································································· 8
7 Function Description ······························································································· 8
7.1 Program Memory ····························································································································8
7.2 Data Memory····································································································································9
7.2.1 Special Purpose Registers ··································································································· 9
7.2.2 USB Application FIFOs···································································································· 21
7.3 I/O Ports··········································································································································22
7.3.1 Programmable Large Current···························································································· 22
7.3.2 Wakeup by Port Change Function ···················································································· 22
7.4 USB Application·····························································································································23
7.4.1 Detect PS/2 or USB Mode ································································································ 23
7.4.2 USB Device Controller ····································································································· 24
7.4.3 Device Address and Endpoints ························································································· 24
7.5 Reset 24
7.5.1 Power-On Reset ················································································································ 24
7.5.2 WatchDog Reset················································································································ 25
7.5.3 USB Reset························································································································· 25
7.6 Power Saving Mode·······················································································································25
7.6.1 Power Down Mode ··········································································································· 25
7.6.2 Dual Clock Mode·············································································································· 26
7.7 Interrupt··········································································································································26
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
•1
EM78612
Universal Serial Bus Microcontroller
8 Absolute Maximum Ratings···································································· 27
9 DC Electrical Characteristic················································································· 28
10 Application Cricuit···································································································· 30
APPENDIX
A. Special Register Map ···························································································· 31
B. Instruction Set ········································································································· 32
C. Code option Register ···························································································· 34
2•
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
Specification Revision History
Doc. Version
1.0
Revision Description
Initial Version
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
Date
2006/03/22
•3
EM78612
Universal Serial Bus Microcontroller
1
General Description
The EM78612 is a series of Universal Serial Bus 8-bit RISC microcontrollers. It is
specifically designed for USB low speed device application and to support legacy
device such as PS/2 mouse. The EM78612 also support one device address and two
endpoints..
The EM78612 is implemented on a RISC architecture. It has five-level stack and six
interrupt sources. The amount of General Input/Output pins is up to12. Each device
has 80 bytes SRAM. The ROM size of the EM78612 is 2K.
These series of chips have Dual Clock mode which allows the device to run on low
power saving frequency.
2
Features
Low-cost solution for low-speed USB devices, such as mouse, joystick, and
gamepad.
USB Specification Compliance
• Universal Serial Bus Specification Version 1.1
• USB Device Class Definition for Human Interface Device (HID), Firmware
Specification Version 1.1
• Support 1 device address and 2 endpoints (EP0 and EP1)
USB Application
• USB protocol handling
• USB device state handling
• Identifies and decodes Standard USB commands to EndPoint Zero
PS/2 Application Support
• Built-in PS/2 port interface
Built-in 8-bit RISC MCU
•
•
•
•
•
•
5 level stacks for subroutine and interrupt
6 available interrupts
8-bit real time clock/counter (TCC) with overflow interrupt
Built-in RC oscillator free running for WatchDog Timer and Dual clock mode
Two independent programmable prescalers for WDT and TCC
Two methods of power saving:
1. Power-down mode (SLEEP mode)
2. Low frequency mode.
• Two clocks per instruction cycle
I/O Ports
4•
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
• Up to 12 general purposes I/O pins grouped into two ports (Port 6 and 7).
• Up to 2 LED sink pins
• Each GPIO pin of Ports 6 & Port 7 has an internal programmable pull-high
resistor
• Each GPIO pin of Ports 6 has an internal programmable pull- low resistor
• Each GPIO pin wakes up the MCU from sleep mode by input state change
Internal Memory
• Built-in 2048*13 bits MASK ROM
• Built-in 80 bytes general purpose registers (SRAM)
• Built-in USB Application FIFOs.
Operation Frequency
• Normal Mode: MCU runs on the external oscillator frequency
• Dual Clock Mode: MCU runs at the frequency of 256 KHz (or 32KHz, 4KHz,
500Hz), emitted by the internal oscillator with the external ceramic resonator
turned off to save power.
Built-in 3.3V Voltage Regulator
• For MCU power supply
• Pull-up source for the external USB resistor on D-pin.
Package Type
•
•
•
•
3
16 pin PDIP(300MIL) / SOP(150MIL) (EM78612 AP / AM)
18 pin PDIP(300MIL) / SOP(300MIL) (EM78612 BP / BM)
20 pin PDIP(300MIL) / SOP(300MIL) (EM78612 CP / CM)
20 pin SSOP(209MIL) (EM78612 FM)
Applications
This microcontroller is designed for USB low speed device application or non-USB
embedded device. It is also suitable for PS/2 mouse application.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
•5
EM78612
Universal Serial Bus Microcontroller
4
Pin Configuration
EM78612A
P61
1
16
P60
P62
2
15
P64
P63
3
14
P65
P70
4
13
P71
P72
5
12
D+/P50
VSS
6
11
D-/P51
V3.3V
7
10
VDD
OSCI
8
9
OSCO
EM78612B
P60
1
18
P64
P61
2
17
P65
P62
3
16
P66
P63
4
15
P67
P70
5
14
P71
P72
6
13
D+/P50
VSS
7
12
D-/P51
V3.3V
8
11
VDD
OSCI
9
10
OSCO
EM78612C
6•
P60
1
20
P64
P61
2
19
P65
P62
3
18
P66
P63
4
17
P67
P70
5
16
P71
P72
6
15
P73
NC
7
14
D+/P50
VSS
8
13
D-/P51
V3.3V
9
12
VDD
OSCI
10
11
OSCO
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
5
Pin Description
Symbol
I/O
Function
OSCI
I
OSCO
I/O
Return path for 6MHz / 12MHz ceramic resonator.
V3.3V
O
3.3V DC voltage output from internal regulator. This pin should be tied to a
4.7 F decoupling capacitor to GND.
P60 ~ P67
I/O
6MHz / 12MHz ceramic resonator input.
Port6 offers up to 8 GIOP pins.
P70 ~ P73
I/O
The pull high resistors (132K Ohms) and pull low resistors (10K Ohm) are
selected through pin programming.
Port7 offers up to 4 GIOP pins. The sink current of P70 & P71 are programmable
for driving LED.
Each pin has pull high resistors (132K Ohm) that can be selected through pin
programming.
USB Plus data line interface or PS/2 line interface are user-defined through
firmware setting.
D+ / P50
I/O
When the EM78612 is running under PS/2 mode, this pin will have an internal
pulled-high resistor (2.2K Ohm), with VDD=5.0V.
When this pin is used as a PS/2 line interface, it will generate an interrupt when
its state changes (Port5 state change interrupt enable).
D- / P51
I/O
USB Minus data line interface or PS/2 line interface are user-defined through
firmware setting.
When the EM78612 is running under PS/2 mode, this pin will have an internal
pulled-high resistor (2.2K Ohm), with VDD=5.0V.
When this pin is used as a PS/2 line interface, it will generate an interrupt when
its state changes (Port5 state change interrupt enable).
When the EM78612 is running under USB mode, this pin will have an internal
pulled-high resistor, 1.5k Ohm, with V3.3=3.3V.
VDD
-
Connects to the USB power source or to a nominal 5V-power supply. Actual VDD
range can vary between 4.4V and 5.2V.
VSS
-
Connects to ground.
Table 5-1 Pin Descriptions
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
•7
EM78612
Universal Serial Bus Microcontroller
6
Function Block Diagram
OSCI
Built-in
RC
OSCO
WDT
Timer
V3.3
D+
3.3V
Regulator
Oscillator
Timing
Control
Prescaler
WDT
Reset &
Sleep &
Wake up
Control
VDD
Prescaler
TCC
R1
(TCC)
D-
R2
(PC)
Transceiver
ROM
USB
Device
Controller
Instruction
register
RAM
Stack1
Stack2
Stack3
Stack4
Stack5
R3
(Status)
ALU
Interrupt
Control
Instruction
Decoder
R4
(RSR)
ACC
DATA & CONTROL BUS
I/O
Port 5
I/O
Port 6
I/O
Port 7
Figure 6-1 EM78612 Series Function Block Diagram
7
Function Description
The memory of EM78612 is organized into four spaces, namely; User Program
Memory in 2048*13 bits MASK ROM space, Data Memory in 80 bytes SRAM space,
and USB Application FIFOs (for EndPoint0 and EndPoint1). Furthermore, several
registers are used for special purposes.
7.1
Program Memory
The program space of the EM78612 is 2K words, and is divided into two pages. Each
page has 1K words long. After Reset, the 12-bit Program Counter (PC) points to
location zero of the program space.
It has two interrupt vectors, i.e., Interrupt Vectors at 0x0001 and USB Application
Interrupt Vectors at 0x000A. The Interrupt Vector applies to TCC Interrupt, and Port 5
State Changed Interrupt. The USB Application Interrupt Vector is for USB EndPoint
Zero Interrupt, USB Suspend Interrupt, USB Reset interrupt, and USB Host Resume
Interrupt.
After an interrupt, the MCU will fetch the next instruction from the corresponding
address as illustrated in the following diagram.
8•
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
After reset
Address
Program Counter
0x0000
Reset Vector
0x0001
Interrupt Vector
0x000A
USB Application Interrupt Vector
Page 0
0x03FF
0x0400
Page 1
0x07FF
7.2
Data Memory
The Data Memory has 80 bytes SRAM space. It is also equipped with USB Application
FIFO space for USB Application. The Figure 7-1 (next page) shows the organization of
the Data Memory Space.
7.2.1
Special Purpose Registers
When the micro-controller executes the instruction, specific registers are invoked for
assistance, such as; Status Register which records the calculation status, Port I/O
Control Registers which control the I/O pins’ direction, etc. The EM78612 series
provides a lot more of other special purpose registers with different functions.
There are 15 Special Operation Registers which are located from Address 0x00 to 0x0F.
On other hand, 10 more Special Control Registers are available to control functions or
I/O direction. These are arranged from Address 0x05 to 0x0F.
Note
that Special Control Registers can only be read or written by two instructions; IOR and
IOW.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
•9
EM78612
Universal Serial Bus Microcontroller
00
01
02
03
04
R0
R1
R2
R3
R4
(Indirection Addressing Register)
(Time Clock / Counter Register)
(Program Counter) & Stack
(Status Register)
(RAM Select Register)
05
06
07
08
09
R5
R6
R7
R8
R9
(Data line I/O Register)
(Port 6 I/O Register)
(Port 7 I/O Register)
(Port6 wakeup pin selection Register)
(Port7 wakeup pin selection Register)
0C
0D
0E
0F
10
IOC5
IOC6
IOC7
IOC8
IOCA (Operation mode Control Register)
IOCB (Port 6 pull low Control Register)
IOCC (Port 6 pull high Control Register)
IOCD (Port 7 pull high Control Register)
IOCE (Special Function Control Register)
IOCF (Interrupt Mask Register)
RC (USB Application Status Register)
RD (USB Application FIFO address register)
RE (USB Application FIFO data register)
RF (Interrupt Status Register)
00
01
10
11
General Purpose Register
1F
(Port 5 I/O Control Register)
(Port 6 I/O Control Register)
(Port 7 I/O Control Register)
(Sink Curent Control Register)
EP0's FIFO
EP1's FIFO
Data Byte Pointer of EP0
Data Byte Pointer of EP1
! "$#
! "%
! "!&
! "!'
! " (
! "!)
! "!*
! "$+
20
General Purpose
Registers
(Bank0)
General Purpose
Registers
(Bank1)
3F
Fig 7-1 The Organization of EM78612 Data RAM
7.2.1.1 Operation Registers in Bank 0
The following introduces each of the Operation Registers under the Special Purpose
Registers. The Operation Registers are arranged according to the order of registers’
address. Note that some registers are read only, while others are both readable and
writable.
R0 (Indirect Address Register) Default Value: (0B_0000_0000)
R0 is not a physically implemented register. Its major function is to be an indirect
address pointer. Any instruction using R0 as a pointer actually accesses the data
pointed by the RAM Select Register (R4).
R1 (Time / Clock Counter) Default Value: (0B_0000_0000)
This register TCC, is an 8-bit timer or counter. It is readable and writable as any other
register. The Timer module will increment every instruction cycle . The user can work
around this by writing an adjusted value. The Timer interrupt is generated when the R1
register overflows from FFh to 00h. This overflow sets bit TCIF(RF[0]). The interrupt
can be masked by clearing bit TCIE (IOCF[0]).After Power-on reset and WatchDog
reset, the initial value of this register is 0x00.
10 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
R2 (Program Counter & Stack) Default Value: (0B_0000_0000)
The EM78612 Program Counter is an 11-bit long register that allows access to 2K
bytes of Program Memory with 5 level stacks. The eight LSB bits, 00~07, are located at
R2, while the one MSB bits, 10, is located at R3 [5].The Program Counter is cleared
after Power-on reset or WatchDog reset. The first instruction that is executed after a
reset is located at Address 00h.
R3
07 06 05 04 03 02 01 00
CALL
R2
10 09 08 07 06 05 04 03 02 01 00
PAGE0
0
0000 ~ 03FF
PAGE1
1
0400 ~ 07FF
Stack1
Stack2
RET
RETL
RETI
Stack3
E
Stack4
Stack5
Fig 7-2 The Structure of ROM Page
R3 (Status Register) Default Value:(0B_0001_1000)
7
6
5
4
3
2
1
0
-
-
PS0
T
P
Z
DC
C
R3 [0] Carry y/Borrow flag. For ADD , SUB Instructions
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
NOTE
For Borrow, the polarity is reversed.For rotate (RRC, RLC) instructions, this bit
is loaded with either the high or low-order bit of the source register
R3 [1] Auxiliary carry /borrow flag. For ADD , SUB Instructions
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
NOTE
For Borrow, the polarity is reversed.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 11
EM78612
Universal Serial Bus Microcontroller
R3 [2] Zero flag. It will be set to 1 when the result of an arithmetic or logic operation is
zero.
R3 [3] Power down flag. It will be set to 1 during Power-on phase or by “WDTC”
command and cleared when the MCU enters into Power down mode. It remains
in previous state after WatchDog Reset.
1: Power-on.
0: Power down
R3 [4] Time-out flag. It will be set to 1 during Power-on phase or by “WDTC” command.
It is reset to 0 by WDT time-out.
1: WatchDog timer without overflow.
0: WatchDog timer with overflow.
The various states of Power down flag and Time-out flag at different conditions are
shown below:
Condition
1
1
Power-on reset
1
1
WDTC instruction
0
*P
WDT time-out
1
0
Power down mode
1
0
Wakeup caused by port change during Power down mode
*P: Previous status before WDT reset
R3 [5] Page selection bit. This bit is used to select a page of program memory (refer to
R2, Program Counter).
PS0
Program Memory Page [Address]
0
Page 0 [0000-03FF]
1
Page 1 [0400-07FF]
R3 [6,7] Reserved registers.
12 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
R4 (RAM Select Register) Default Value: (0B_0xxx_xxxx)
7
6
5
4
3
2
1
0
-
BK0
Ad5
Ad4
Ad3
Ad2
Ad1
Ad0
R4 (RAM select register) contains the address of the registers.
R4 [0~5]
are used to select registers in 0x00h~0x3Fh. The address 0x00~0x1F is
common space. After 0x1Fh, SRAM is grouped into two banks.
R4 [6]
are used to select register banks. To select a registers bank, refer to the
following examples and the table below:
R4=01111100 points to the register 0x3C in Bank 1.
R4[6]Bk0
RAM Bank #
0
Bank 0
1
Bank 1
R5 (Data Line I/O Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
-
-
-
-
-
-
1
0
D- or DATA D+ or CLK
R5 [0]
USB D+ line register or PS/2 clock interface register.
R5 [1]
USB D- line register or PS/2 data interface register.
These two bits are BOTH writable and readable when the MCU is operating under PS/2
mode. But under USB Mode, these two bits cannot be accessed.
R5 [2~7]
NON Used .The value is zero.
R6 (Port 6 I/O Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
P67
P66
P65
P64
P63
P62
P61
P60
R7 (Port 7 I/O Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
-
-
-
-
P73
P72
P71
P70
R8 (Port 6 Wake-up Pin Selection Register) Default Value: (0B_1111_1111)
7
6
5
4
3
2
1
0
/Wu67
/wu66
/Wu65
/Wu64
/Wu63
/Wu62
/Wu61
/Wu60
R8 [0 ~ 7] Select which of the Port 6 pins are to be defined to wake-up the MCU from
sleep mode. When the state of the selected pins changes during sleep
mode, the MCU will wake-up and execute the next instruction automatically.
1: Disable the wake-up function
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 13
EM78612
Universal Serial Bus Microcontroller
0: Enable the wake-up function
R9 (Port 7 Wake-up Pin Selection Register) Default Value: (0B_1111_1111)
7
6
5
4
3
2
1
0
-
-
-
-
/Wu73
/Wu72
/Wu71
/Wu70
R9 [0 ~ 3] Select which of the Port 7 pins are to be defined to wake-up the MCU from
sleep mode. When the state of the selected pins changes during sleep
mode, the MCU will wake-up and execute the next instruction automatically.
1: Disable the wake-up function
0: Enable the wake-up function
RC (USB Application Status Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
EP0_W
EP0_R
EP1_R
0
Device_Resume
Host_Suspend
EP0_Busy
Stall
RC [0]
Stall flag. When MCU receives an unsupported command or invalid
parameters from host, this bit will be set to 1 by the firmware to notify the
UDC to return a STALL handshake. When a successful SETUP transaction
is received, this bit is cleared automatically. This bit is both readable and
writable.
RC [1]
EP0 Busy flag. When this bit is equal to “1,” it indicates that the UDC is
writing data into the EP0’FIFO or reading data from it. During this time, the
firmware will avoid accessing the FIFO until UDC finishes writing or reading.
This bit is only readable.
RC [2]
Host Suspend flag. If this bit is equal to 1, it indicates that USB bus has no
traffic for the specified period of 3.0 ms. This bit will also be cleared
automatically when a bus activity takes place. This bit is only readable.
,
RC [3]
This bit should be used in Dual Mode
Device Resume flag. This bit is set by firmware to general a signal to
wake-up the USB host and is cleared as soon as the USB Suspend signal
becomes low. This bit can only be set by firmware and cleared by the
hardware.
-
This bit should be used in Dual Mode
RC [4]
Undefined Register. The default value is 0.
RC [5,6]
EP1_R / EP0_R flag. These two bits inform the UDC to read the data written
by firmware from the FIFO. Then the UDC sends the data to the host
automatically. After UDC finishes reading the data from the FIFO, this bit is
cleared automatically.
14 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
Therefore, before writing data into the FIFO, the firmware will first check this
bit to prevent overwriting the existing data. These two bits can only be set
by the firmware and cleared by the hardware.
RC [7]
EP0_W flag. After the UDC completes writing data to the FIFO, this bit will
be set automatically. The firmware will clear it as soon as it gets the data
from EP0’s FIFO. Only when this bit is cleared that the UDC will be able to
write a new data into the FIFO.
Therefore, before the firmware can write a data into the FIFO, this bit must
first be set by the firmware to prevent UDC from writing data at the same
time. This bit is both readable and writable.
RD (USB Application FIFO Address Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
0
0
0
UAD4
UAD3
UAD2
UAD1
UAD0
RD [0~4]
USB Application FIFO address registers. These five bits are the address
pointer of USB Application FIFO.
RD [5~7]
Undefined registers. The default value is zero.
RE (USB Application FIFO Data Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
UD7
UD6
UD5
UD4
UD3
UD2
UD1
UD0
RE (USB Application FIFO data register) contains the data in the register of which
address is pointed by RD.
NOTE
For example, if we want to read the fourth byte of the EndPoint Zero, we will use the
address of EP0 (0x00) and Data Byte Pointer of EP0 (0x10) to access it.
// Read the 4rd byte of the EP0 FIFO
// First, assign the data byte pointer of EP0 register (0X10) with 0X03.
MOV A, @0X10
MOVRD, a
// Move data in A to RD register
MOV A, @0X03
MOVRE , A
// Move data in A to RE register
// Then read the content from EP0 FIFO (0x00) 4rd byte
MOV A, @0X00
MOVRD, A
// Assign address point to EP0 FIFO
MOVA, RE
// Read the fourth byte data (byte3) of the EP0 FIFO
MOV A, 0X0E// Read the fifth byte data (byte4) of the EP0 FIFO
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 15
EM78612
Universal Serial Bus Microcontroller
RF (Interrupt Status Register ) Default Value: (0B_0000_0000)
7
6
-
--
RF [0]
5
4
3
2
Port 5 State USB Host
USB
USB
Change_IF Resume_IF Reset_IF Suspend_IF
1
0
EP0_IF
TCC_IF
TCC Overflow interrupt flag. It will be set while TCC overflows, and is
cleared by the firmware.
RF [1]
EndPoint Zero interrupt flag. It will be set when the EM78612 receives
Vender /Customer Command to EndPoint Zero. This bit is cleared by the
firmware.
RF [2]
USB Suspend interrupt flag. It will be set when the EM78612 finds the USB
Suspend Signal on USB bus. This bit is cleared by the firmware.
RF [3]
USB Reset interrupt flag. It will be set when the host issues the USB Reset
signal.
RF [4]
USB Host Resume interrupt flag. It is set only under Dual Clock mode when
the USB suspend signal becomes low.
RF [5]
Port 5 State Change interrupt flag. It is set when the Port 5 state changes .
(Port 5 state change interrupt only work in PS/2 mode.)
RF [6]
Default value is zero and do not modify it.
R10~R1F are General purpose registers. These registers can be used no matter what
Bank Selector is. There are 2 banks(BK0 & BK1) R20~R3F General purpose registers,
Select by R4 [6].
7.2.1.2 Control Registers in Bank 0
Special purpose registers for special control purposes are also available. Except for the
Accumulator (A), these registers must be read and written by special instructions. One
of these registers, CONT, can only be read by the instruction "CONTR" and written by
"CONTW" instruction. The remaining special control registers can be read by the
instruction "IOR" and written by the instruction "IOW."
A (Accumulator Register)
The accumulator is an 8-bit register that holds operands and results of arithmetic
calculations. It is not addressable.
16 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
CONT (Control Register)
7
6
5
4
3
2
1
0
RW_E
/INT
TSR2
TSR1
TSR0
PSR2
PSR1
PSR0
NOTE
The CONT register can be read by the instruction "CONTR" and written by the
instruction “CONTW."
CONT [0~2]
WatchDog Timer prescaler bits. These three bits are used as the
prescaler of WatchDog Timer.
CONT [3~5]
TCC Timer prescaler bits.
The relationship between the prescaler value and these bits are as shown below:
PSR2/TSR2
PSR1/TSR1
PSR0/TSR0
TCC Rate
WDT Rate
( 8mS )
0
0
0
6MHz / 2
8 ms
0
0
1
6MHz / 4
16 ms
0
1
0
6MHz / 8
32 ms
0
1
1
6MHz / 16
64 ms
1
0
0
6MHz / 32
128 ms
1
0
1
6MHz / 64
256 ms
1
1
0
6MHz / 128
512 ms
1
1
1
6MHz / 256
1024 ms
CONT [6] Interrupt enable control bit. This bit toggles Interrupt function between
enable and disable. It is set to 1 by the interrupt disable instruction "DISI"
and reset by the interrupt enable instructions "ENI" or "RETI."
0: Enable the Interrupt function.
1: Disable the Interrupt function.
CONT [7] Remote wake-up enable bit. This bit is set to 1, if host enables device to
remote wake-up PC. It could be modified by SetFeature() & ClearFeature()
Request.
IOC5 ~IOC7 I/O Port Direction Control Registers
Each bit controls the I/O direction of three I/O ports ( Port5~Port7 ) respectively. When
these bits are set to 1, the relative I/O pins become input pins. Similarly, the I/O pins
becomes outputs when the relative control bits are cleared.
1: Input direction.
0: Output direction.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 17
EM78612
Universal Serial Bus Microcontroller
IOC5 (Data Line I/O Control Register) Default Value: (0B_0000_0011)
7
6
5
4
3
2
1
0
0
0
0
0
0
0
P51
P50
IOC5 [2~7] Undefined registers. The default value is 0.
IOC6 (Port 6 I/O Control Register) Default Value: (0B_1111_1111)
7
6
5
4
3
2
1
0
P67
P66
P65
P64
P63
P62
P61
P60
IOC7 (Port 7 I/O Control Register) Default Value: (0B_0000_1111)
7
6
5
4
3
2
1
0
-
-
-
-
P73
P72
P71
P70
IOC8 (Sink Current Control Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
0
0
Sink1.1
Sink1.0
0
0
Sink01
Sink0.0
IOC8 [0,1][4,5]
are P70/P71 sink current control registers. Four levels are offered for
selection:
Sink0.1/1.1
Sink0.0/1.0
Sink Current
0
0
3mA±10%
0
1
6mA±10%
1
0
12mA±10%
1
1
25mA±10%
The default current after Power-on reset is 3mA.
IOCA (Operation Mode Control Register) Default Value: (0B_1100_0011)
7
6
5
4
3
2
1
0
Dual_Frq.1
Dual_Frq.0
0
0
0
0
PS/2
USB
IOCA [0,1]
These two bits are used to select the operation mode. The definition of
these two control registers is described in the table below.
18 •
IOCA[1]
IOCA[0]
Operation Mode
0
0
Detect Mode
0
1
USB Mode
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
1
0
PS/2 Mode
1
1
USB Test Mode
IOCA [2~5]
Undefined registers. The default value is 0.
IOCA [6,7]
Select the operation frequency in Dual Clock Mode. Four frequencies
are available and can be chosen as Dual Clock mode for running the
MCU program.
Dual_Frq.1
Dual_Frq.0
Frequency
0
0
500Hz
0
1
4kHz
1
0
32kHz
1
1
256kHz
IOCB (Port 6 Pull-Low Control Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
PL67
PL66
PL65
PL64
PL63
PL62
PL61
PL60
IOCB [0~7]
Select whether the 10K Ohm pull-low resistor of Port 6 individual pin is
connected or not.
1: Enable the pull-low function.
0: Disable the pull-low function.
IOCC (Port 6 Pull-High Control Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
PH67
PH66
PH65
PH64
PH63
PH62
PH61
PH60
IOCC [0~7]
Select whether the 132K Ohm pull-high resistor of Port 6 individual pin is
connected or not.
1: Enable the pull-high function.
0: Disable the pull-high function.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 19
EM78612
Universal Serial Bus Microcontroller
IOCD (Port 7 Pull-High Control Register) Default Value: (0B_0000_0000)
7
6
5
4
3
2
1
0
-
-
-
-
PH73
PH72
PH71
PH70
IOCD [0~3]
Select whether the 132K Ohm pull-high resistor of Port 7 individual pin is
connected or not.
1: Enable the pull-high function.
0: Disable the pull-high function.
IOCE (Special Function Control Register) Default Value: (0B_1111_0000)
7
6
5
4
3
2
1
0
/Dual clock
/WUE
WTE
RUN
0
0
0
0
IOCE [0~3]
Undefined register. The default value is zero.
IOCE [4]
Run bit. This bit can be cleared by the firmware and set during power-on,
or by the hardware at the falling edge of wake-up signal. When this bit is
cleared, the clock system is disabled and the MCU enters into power
down mode. At the transition of wake-up signal from high to low, this bit is
set to enable the clock system.
1: Run mode. The EM78612 is working normally.
0: Sleep mode. The EM78612 is in power down mode.
IOCE [5]
WatchDog Timer enable bit. The bit disable/enables the WatchDog
Timer.
1: Enable WDT.
0: Disable WDT.
NOTE
If the Code Option WTC bit is "0,” WDT is always disabled.
IOCE [6]
Enable the wake-up function as triggered by port-change. This bit is set
by UDC.
1: Disable the wake-up function.
0: Enable the wake-up function.
IOCE [7]
Dual clock Control bit. This bit is used to select the frequency of system
clock. When this bit is cleared, the MCU will run on very low frequency
save power and the UDC will stop working.
1: Selects EM78612 to run on normal frequency.
0: Selects to run on slow frequency.
20 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
IOCF (Interrupt Mask Register) Default Value: (0B_0000_0000)
7
6
-
-
IOCF [0~5]
5
4
Port 5 State
USB Host
Change_IE Resume_1E
3
USB
Reset_IE
2
1
0
USB
EP0_IE TCC_IE
Suspend_IE
TCC / EP0 / USB Suspend / USB Reset / USB Host Resume / Port 5
State Change enable bits. These eight bits respectively control the
function of TCC interrupt, EP0 interrupt, USB Suspend interrupt, USB
Reset interrupt, USB Host Resume interrupt, Port5 State Change
interrupt, Individual interrupt is enabled by setting its associated control
bit in the IOCF to "1".
1: Enable Interrupt.
0: Disable Interrupt.
IOCF[6]
Default value is zero and do not modify it.
Only when the global interrupt is enabled by the ENI instruction that the individual
interrupt will work. After DISI instruction, any interrupt will not work even if the
respective control bits of IOCF are set to 1.
The USB Host Resume Interrupt works only under Dual clock mode. This is
because when the MCU is under sleep mode, it will be waked up by the UDC Resume
signal automatically.
7.2.2
USB Application FIFOs
For USB Application, EM78612 provides an 8-byte First-In-First-Out (FIFO) buffer for
each endpoint. The buffer cannot be accessed directly. However, a corresponding Data
Byte Pointer register for each endpoint is made available to address the individual byte
of the FIFO buffer. The content of the individual byte will map to a special register.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 21
EM78612
Universal Serial Bus Microcontroller
`a\E\G ? O O
b c 7=: ?A@CBED F: ?GBEHJIK@L
LEe TT
798: 8<;>=: ?A@CBED F: ?GBEHJIK@ T
./ 0 1 2 3 4
LEe9LL
IM@CL N OMPRQ PCS
LEe9L T
IM@ T N OMPRQ PCS
5!/ 6 1 2 3 4
.E/ 0 1 2 3 4
5/ 6 1 2 3 4
L
L
T
T
U
U
V
V
W
W
7.3
X
X
Y
Y
Z
Z
;>D [ \ED G ?]: D BEF8^
_ TCC.
The additional hardware process step of the interrupt occurred
including
ADisable interrupt means reserving next time interrupt
process until the instruction “RETI” executed.
BJump to interrupt vector.
CPush “Accumulator”, “R3” and “R4”. Steps “A”, “B”, and “C”
are executed at the same time.
DClear “R3”and“R4”.
EIf the instruction “RETI” is executed, pop “Accumulator”,
“R3” and “R4”.
FReturn to main program and enable interrupt. Step “E” and “F” are
executed at the same time.
8
Absolute Maximum Ratings
Symbol
Min
Max
Unit
0
70
ºC
Storage temperature
-65
150
ºC
Input voltage
-0.5
6.0
V
Output voltage
-0.5
6.0
V
Temperature under bias
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 27
EM78612
Universal Serial Bus Microcontroller
9
DC Electrical Characteristic
(T = 25 f , VDD = 5V, VSS = 0V)
Symble
Parameter
Condition
Min
Type Max
Unit
3.3V Regulator
VRag
Output voltage of 3.3v Regulator
VDD = 5V
3.0
VResetL
Low Power Reset detecting low Voltage
-
V
VResetH
Low Power Reset detecting high Voltage
-
V
Ireg
3.3V Regulator driving capacity
V3.3 = 3.3V
3.3
-
-
-
-
3.6
100
V
mA
MCU Operation
IIL
Input Leakage Current for input pins
VIN= VDD,VSS
VIHX
Clock Input High Voltage
OSCI
2.5
-
-
V
VILX
Clock Input Low Voltage
OSCI
-
-
1.0
V
ICC1
VDD operating supply current –
Normal frequency operation mode
Freq. = 6MHz
-
-
10
mA
ISB
Operating supply current 1 –
Power down mode
WDT disabled
-
-
100
2.0
-
-
V
g
1
A
h
h
A
GPIO Pins
VIH
Input High Voltage
Port 5
VIL
Input Low Voltage
Port 5
-
-
0.8
V
VIH
Input High Voltage
Port 6 & 7
2.0
-
-
V
VIL
Input Low Voltage
-
-
0.8
V
IOH1
Output High Voltage
(Port 6 & P72~P73)
Port 6 & 7
VOH1 = 2.4V
VREG = 3.3V
IOL1
Output Low Voltage
(Port 6 )
IOH2
IOL2
11
mA
VOL2 = 0.4V
VREG = 3.3V
11
mA
Output High Voltage
(Port5)
VOH2 = 2.4V
VDD = 5V
7
mA
Output Low Voltage
(Port5)
VOL2 = 2.4V
VDD = 5V
13
mA
RPH
Pull-high resister
The input pin with internal
pull-high resistor of Port6 or
Port7 is connected to VSS.
100
K
RPL
Pull-low resister
The input pin with internal
pull-low resistor of Port6 is
connected to VDD.
8
K
Symble
Parameter
Condition
Min
Type Max
Unit
USB Interface
28 •
VOH
Static Output High
VOL
Static Output Low
VDI
Differential Input Sensitivity
VCM
Differential Input Command Mode Range
VSE
Single Ended Receiver Threshold
USB operation Mode
USB operation Mode
2.8
-
3.6
V
-
-
0.3
V
0.2
-
-
V
0.8
-
2.5
V
0.8
-
2.0
V
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
CIN
Transceiver Capacitance
VRG
Output Voltage of Internal Regulator
RPH
Pull-high resister
(D-)
-
-
20
pF
3.0
-
3.6
V
Ki
1.5
Programmable Large Current
ISink1
P70, P71 Output Sink Current
VOUT = 0.4V,
-30%
IOC8[0,1] or IOC8[4,5] = 00
3
+30%
mA
ISink2
P70, P71 Output Sink Current
VOUT = 0.4V,
-30%
IOC8[0,1] or IOC8[4,5] = 01
6
+30%
mA
ISink3
P70, P71 Output Sink Current
VOUT = 0.4V,
-30%
IOC8[0,1] or IOC8[4,5] = 10
12
+30%
mA
ISink4
P70, P71 Output Sink Current
VOUT = 0.4V,
-30%
IOC8[0,1] or IOC8[4,5] = 11
25
+30%
mA
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 29
EM78612
Universal Serial Bus Microcontroller
10 Application Cricuit
EM78612_CP
P60
P64
P61
P65
P62
P66
P63
P67
P70
P71
P72
P73
NA
USB Application
V3.3
R1
1.5k
C3
4.7uF
V3.3
VDD
OSCI
OSCO
1
2
3
4
USB connector
Note1. IF IOCA = USB mode, MCU D- pin internal
pull-high to V3.3 with 1.5k resistor.
P50
D+/CLK
D-/DATA
J1
P51
P50
Note2. IF IOCA = USB test mode, it is necessary that
D- pin external pull-high to V3.3 with 1.5k
resistor.
V3.3
VSS
P51
C1
10uF
VDD
C2
0.1uF
PS/2 Application
Y1
C4
30pF
6MHz or 12MHz resonator
J2
C5
P50
30pF
P51
Note :
A. Place C1 and C2 close to MCU VDD pin.
B. Place Y1, C4 and C5 close to MCU OSCI pin.
C. In USB application, it is necessary to place C3 close to MCU V3.3 pin.
D. Port6 and Port7 are 3.3V level I/O.
E. Port60 is input only and without internal pull-high and pull-low resistor.
30 •
VDD
5
3
1
6
4
2
VDD
PS/2 connector
Note3. IF IOCA = PS/2 mode, MCU CLK and DATA pin
internal pull-high to VDD with 4.7k resistor.
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
Appendix
A. Special Register Map
Operation Registers
address
name
0x00
R0
0x01
R1(TCC)
0x02
R2(PC)
0x03
R3(STATUS)
-
-
0x04
R4(RSR)
-
BK0
0x05
R5(Port5)
-
-
-
-
-
-
0x06
R6(Port6)
P67
P66
P65
P64
P63
0x07
R7(Port7)
-
-
-
-
/Wu67
/Wu66
/Wu65
-
-
EP0_W
EP0_R
0x08
0x09
Bit7
R8(Port6
Wake-up Pin
Selection)
R9(Port7
Wake-up Pin
Selection)
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Default value
Indirect Addressing Register
0B_0000_0000
Timer/Clock Counter
0B_0000_0000
Program Counter
0B_0000_0000
PS0
T
P
Z
DC
C
Select the register(address: 00~3F) in the indirect addressing mode
0B_0001_1xxx
0B_0xxx_xxxx
P51/D-
P50/D+
/DATA
/CLK
P62
P61
P60
0B_0000_0000
P73
P72
P71
P70
0B_0000_0000
/Wu64
/Wu63
/Wu62
/Wu61
/Wu60
0B_1111_1111
-
-
/Wu73
/Wu72
/Wu71
/Wu70
0B_1111_1111
EP1_R
0
Device
Resume
Host
_SUSPEND
UDC
_Writing
STALL
0B_0000_0000
0B_0000_0000
0x0C
RC
0x0D
RD
USB Application FIFO Address Register
0B_0000_0000
0x0E
RE
USB Application FIFO Data Register
0B_0000_0000
0x0F
RF
-
EP1_IF
USB Host
Port5 state
USB
USB
EP0_IF
Resume_
change_IF
Reset_IF Suspend_IF
IF
TCC_IF
0B_0000_0000
Control Registers
address
name
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
Default value
CONT
RW_E
INT
TSR2
TSR1
TSR0
PSR2
PSR1
PSR0
0B_0100_0000
0x05
IOC5
Port5 Direction Control Register
0B_0000_0011
0x06
IOC6
Port6 Direction Control Register
0B_1111_1111
0x07
IOC7
Port7 Direction Control Register
0B_0000_1111
0x08
IOC8 (Sink
Current)
0x09
IOC9
0x0A
IOCA
0x0B
IOCB
/PL67
0x0C
IOCC
0x0D
-
-
Sink[70]_1
Sink[70]_0
0B_0000_0000
-
PS/2
USB
0B_1100_0000
/PL63
/PL62
/PL61
/PL60
0B_0000_0000
/PH64
/PH63
/PH62
/PH61
/PH60
0B_0000_0000
-
-
/PH73
/PH72
/PH71
/PH70
0B_0000_0000
WTE
RUN
0
0
0
0
0B_1111_0000
TCC_IE
0B_0000_0000
Sink[71]_1
Sink[71]_0
-
-
-
/PL66
/PL65
/PL64
/PH67
/PH66
/PH65
IOCD
-
-
0x0E
IOCE
/Dual clock
/WUE
0x0F
IOCF
0
EP1_IE
Reserved
Dual_Frq.1 Dual_Frq.0
Port5_State_ USB HOST
Change_IE Resume_IF
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
USB
USB
EP0_IE
Reset_IE Suspend_IE
• 31
EM78612
Universal Serial Bus Microcontroller
B. Instruction Set
Each instruction in the instruction set is a 11-bit word divided into an OP code and one
or more operands. All instructions are executed within one single instruction cycle
(consisting of 2 oscillator periods), unless the program counter is changed by(a) Executing the instruction "MOV R2,A", "ADD R2,A", "TBL", or any other instructions
that write to R2 (e.g. "SUB R2,A", "BS R2,6", "CLR R2", ⋅⋅⋅⋅).
(b) execute CALL, RET, RETI, RETL, JMP, Conditional skip (JBS, JBC, JZ, JZA, DJZ,
DJZA) which were tested to be true.
Under these cases, the execution takes two instruction cycles.
In addition, the instruction set has the following features:
(1). Every bit of any register can be set, cleared, or tested directly.
(2). The I/O register can be regarded as general register. That is, the same instruction
can operate on I/O register.
The symbol "R" represents a register designator that specifies which one of the registers (including operational
registers and general purpose registers) is to be utilized by the instruction. Bits 6 and 7 in R4 determine the selected
register bank. "b" represents a bit field designator that selects the value for the bit located in the register "R" and
affects operation. "k" represents an 8 or 10-bit constant or literal value.
INSTRUCTION BINARY
HEX
MNEMONIC
OPERATION
STATUS AFFECTED
0 0000 0000 0000
0000
NOP
No Operation
None
0 0000 0000 0001
0001
DAA
Decimal Adjust A
C
0 0000 0000 0010
0002
CONTW
A → CONT
None
0 0000 0000 0011
0003
SLEP
0 → WDT, Stop oscillator
T,P
0 0000 0000 0100
0004
WDTC
0 → WDT
T,P
0 0000 0000 rrrr
000r
IOW R
A → IOCR
None
0 0000 0001 0000
0010
ENI
Enable Interrupt
None
0 0000 0001 0001
0011
DISI
Disable Interrupt
None
0 0000 0001 0010
0012
RET
[Top of Stack] → PC
None
0 0000 0001 0011
0013
RETI
[Top of Stack] → PC,
Enable Interrupt
None
0 0000 0001 0100
0014
CONTR
CONT → A
None
0 0000 0001 rrrr
001r
IOR R
IOCR → A
None
0 0000 0010 0000
0020
TBL
R2+A → R2,
Bits 8~9 of R2 unchanged
Z,C,DC
0 0000 01rr rrrr
00rr
MOV R,A
A→R
None
0 0000 1000 0000
0080
CLRA
0→A
Z
0 0000 11rr rrrr
00rr
CLR R
0→R
Z
0 0001 00rr rrrr
01rr
SUB A,R
R-A → A
Z,C,DC
0 0001 01rr rrrr
01rr
SUB R,A
R-A → R
Z,C,DC
0 0001 10rr rrrr
01rr
DECA R
R-1 → A
Z
32 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
INSTRUCTION BINARY
HEX
MNEMONIC
OPERATION
STATUS AFFECTED
0 0001 11rr rrrr
01rr
DEC R
R-1 → R
Z
0 0010 00rr rrrr
02rr
OR A,R
A ∨ VR → A
Z
0 0010 01rr rrrr
02rr
OR R,A
A ∨ VR → R
Z
0 0010 10rr rrrr
02rr
AND A,R
A&R→A
Z
0 0010 11rr rrrr
02rr
AND R,A
A&R→R
Z
0 0011 00rr rrrr
03rr
XOR A,R
A⊕R→A
Z
0 0011 01rr rrrr
03rr
XOR R,A
A⊕R→R
Z
0 0011 10rr rrrr
03rr
ADD A,R
A+R→A
Z,C,DC
0 0011 11rr rrrr
03rr
ADD R,A
A+R→R
Z,C,DC
0 0100 00rr rrrr
04rr
MOV A,R
R→A
Z
0 0100 01rr rrrr
04rr
MOV R,R
R→R
Z
0 0100 10rr rrrr
04rr
COMA R
/R → A
Z
0 0100 11rr rrrr
04rr
COM R
/R → R
Z
0 0101 00rr rrrr
05rr
INCA R
R+1 → A
Z
0 0101 01rr rrrr
05rr
INC R
R+1 → R
Z
0 0101 10rr rrrr
05rr
DJZA R
R-1 → A, skip if zero
None
0 0101 11rr rrrr
05rr
DJZ R
R-1 → R, skip if zero
None
0 0110 00rr rrrr
06rr
RRCA R
R(n) → A(n-1),
R(0) → C, C → A(7)
C
0 0110 01rr rrrr
06rr
RRC R
R(n) → R(n-1),
R(0) → C, C → R(7)
C
0 0110 10rr rrrr
06rr
RLCA R
R(n) → A(n+1),
R(7) → C, C → A(0)
C
0 0110 11rr rrrr
06rr
RLC R
R(n) → R(n+1),
R(7) → C, C → R(0)
C
0 0111 00rr rrrr
07rr
SWAPA R
R(0-3) → A(4-7),
R(4-7) → A(0-3)
None
0 0111 01rr rrrr
07rr
SWAP R
R(0-3) ↔ R(4-7)
None
0 0111 10rr rrrr
07rr
JZA R
R+1 → A, skip if zero
None
0 0111 11rr rrrr
07rr
JZ R
R+1 → R, skip if zero
None
0 100b bbrr rrrr
0xxx
BC R,b
0 → R(b)
None
0 101b bbrr rrrr
0xxx
BS R,b
1 → R(b)
None
0 110b bbrr rrrr
0xxx
JBC R,b
if R(b)=0, skip
None
0 111b bbrr rrrr
0xxx
JBS R,b
if R(b)=1, skip
None
1 00kk kkkk kkkk
1kkk
CALL k
PC+1 → [SP],
(Page, k) → PC
None
1 01kk kkkk kkkk
1kkk
JMP k
(Page, k) → PC
None
1 1000 kkkk kkkk
18kk
MOV A,k
k→A
None
1 1001 kkkk kkkk
19kk
OR A,k
A∨k→A
Z
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 33
EM78612
Universal Serial Bus Microcontroller
INSTRUCTION BINARY
HEX
MNEMONIC
OPERATION
STATUS AFFECTED
1 1010 kkkk kkkk
1Akk
AND A,k
A&k→A
Z
1 1011 kkkk kkkk
1Bkk
XOR A,k
A⊕k→A
Z
1 1100 kkkk kkkk
1Ckk
RETL k
k → A, [Top of Stack] → PC
None
1 1101 kkkk kkkk
1Dkk
SUB A,k
k-A → A
Z,C,DC
1 1111 kkkk kkkk
1Fkk
ADD A,k
k+A → A
Z,C,DC
Note
1 This instruction is applicable to IOCx only.
2 This instruction is not recommended for RE, RF operation.
C. Code Option Register
34 •
Product Specification(V1.0) 03.22.2006
(This specification is subject to change without further notice)
EM78612
Universal Serial Bus Microcontroller
EM78612 has one CODE option registers, which are not part of the normal program memory.
The option bits cannot be accessed during normal program execution.
8
7
6
5
R.S.
4
3
Package_ Package_
1
0
2
OST_1
1
OST_0
0
Frequenc
y
Bit 0 (Frequency) : Frequency Selection.
0: The MCU run on 12 MHz
1: The MCU run on 6 MHz
Bit 2~1 (OST_1 ~ OST_0) : Oscillator Start-up Time.
00: 500us
01: 2ms
10: 8ms
11: 16ms
Bit 4~3 (Package_1 ~ Package_0) : Package type selector.
00 : 16 pins
01 : 18 pins
10 : 20 pins
11 : No define
Bit 5 (R.S.) : Resistor Switch. enable of Transceiver.
0: Disconnect internal USB D- pull high Register
1: Connect internal USB D- pull high Resister
Bit 8~6 :The values are fixed.
Product Specification (V1.0) 03.22.2006
(This specification is subject to change without further notice)
• 35
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 37 Producer : GNU Ghostscript 7.06 Title : Microsoft Word - EM78612_NEW v1.0_20060417_.doc Creator : PScript5.dll Version 5.2.2 Create Date : 4/17/2006 14:59:16 Author : 93068EXIF Metadata provided by EXIF.tools