Emerson Digital Cold Chain 101008 GO Bluetooth Logger User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3623626
Application ID	FyjyYfCuD+AqPSMLwYn6mA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	46.59kB (582314 bits)
Date Submitted	2017-10-31 00:00:00
Date Available	2018-04-29 00:00:00
Creation Date	2017-10-26 17:17:47
Producing Software	福昕风腾PDF套件打印机 版本 7.2.0.0424
Document Lastmod	2017-10-26 17:18:56
Document Title	User manual

GO Bluetooth Logger
User Manual
V4.0
Model：GO BT Logger 1.0
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority
to operate the equipment.
RF Exposure Information
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility
of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm (8 inches)
during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
IC: 10124A-101008
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an uncontrolled environment. In order to avoid the
possibility of exceeding the ISED RSS-102 RF exposure limits, human proximity to the antenna shall not be less than 20cm (8
inches) during normal operation.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la CNR-102 définies pour un environnement non
contrôlé. Afin d'éviter la possibilité de dépasser les limites d'exposition aux fréquences radio de la CNR-102, la proximité humaine
à l'antenne ne doit pas être inférieure à 20 cm (8 pouces) pendant le fonctionnement normal.
CE Regulations:
Caution
Please make sure the temperature for device will be from xx˚C to xx˚C .
The minimum distance between the user and/or any bystander and the radiating structure of
the transmitter is 20cm.
Complies with the essential requirements of Article 3 of the RED 2014/53/EU Directive,
if used for its intended use and that the following standards have been applied:
1.
Health (Article 3.1(a) of the RED Directive)
■ EN 62311: 2008
2.
Safety (Article 3.1(a) of the RED Directive)
Applied Standard(s):
■ EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
3.
Electromagnetic compatibility (Article 3.1 (b) of the RED Directive)
Applied Standard(s):
■ Draft EN 301 489-1 V2.2.0
■ Draft EN 301 489-17 V3.2.0
4.
Radio frequency spectrum usage (Article 3.2 of the RED Directive)
Applied Standard(s):
■ EN 300 328 V2.1.1
1. Function Description
GO Bluetooth Logger is the environment data collector in the monitoring system. It will detect
the temperatures, humidity and vibration of product storage and record them on time. Later it
will be able to upload the records by bluetooth or USB connection. And the uploaded data can be
merged with big data for IoT remote beginning to end monitoring.
2. Features
a)
b)
c)
d)
e)
Temperatures, humidity and vibration detection
Temperatures, humidity and vibration data Logger
Data records uploading (bluetooth or USB connection)
Configuration (bluetooth or USB connection)
Power saving & low power warning (recording)
3. Appearance diagram
Function
Operation
Unplug the power tag
Start system with Self(first time) or change
examination
battery (re-use)
Take away battery or
Stop to work
power down
Pause recording new while APP is downloading
data
the data
LED indication
Pass: Green slow flash
Low batt: Red slow flash
Sensor fault: Red and Green slow flash
Light is off.
Green fast flash 1 sec.
Paired: Green fast flash 1 sec.
Pairing
Data recording
Open the collector APP
Failed: Red fast flash 1 sec.
While recording data, Green
System automatic running
flashing once as marking
light
4. Use the terminal
a) System Start/Stop
i. Unplug the power tag or change battery then power is on. System starts to work and
record the time offset with temperatures, humidity and vibration. It will detect and
record temperatures, humidity and vibration. It will also broadcasting for connection;
ii. Take away battery or power down, system stops to work;
b) Pause recording or restart
i. System will pause recording new data while APP is downloading the data.
ii. The time will be continued when system pause recording.
iii. System will continue recording new data after APP download is over.
iv. After you take off the battery then plug in it again. System will restart to record from the
beginning. The time will be reset too.
v. Every time you download the data that is always the last time recording.
c) Self-examination
i. After removing power tab or restart, system will power on and start self-examination
procedure;
ii. System will check battery and sensors;
iii. The result will be shown by LED;
d) Data collecting and storing
i. System will collect and store the temperatures, humidity and vibration data according
to the configuration;
ii. System could insure every temperatures, humidity and vibration data are accurately;
iii. System could store 130,000 records that is the maximum. It will stop recording new
data if the memory is full.
e) Upload data
i. Bluetooth Logger will be connected to the Data Collector (App) through technology of
BLE (Bluetooth Low Energy);
ii. When BLE build up connection with APP, Bluetooth Logger will upload all stored
temperatures, humidity and vibration data;
f)
Configuration parameters
i. After Bluetooth Logger connected to Data Collector, Data Collector can also modify the
configuration parameters;
ii. The parameters includes as below:
Data recording frequency;
Temperature alarm threshold;
5. Data Collector App function (Android)
a) user activate the App
b) App will start scanning Bluetooth Logger;
c) After APP found Bluetooth Loggers, it will list current Bluetooth Logger to show its status;
d) If user want to connect one of the Bluetooth Loggers, then click the screen list; system will
start connecting with device;
e) Connection is built that will show “Ready” as below:
f)
User can touch screen button “Download” then system will start collecting device records
and showing progress; after download is over, user will see the data list as below:
g) User can touch screen button “CONFIG” to enter configuration and set up all different
parameters (will show current parameters);
6. USB Connecting for test
a) Install COM port driver and test tool on computer;
i. There are driver file names as below:
ccxxxx_usb_cdc.inf
ccxxxx_usb_cdc.cat
ii. For example, there is a COM tool with settings as below:
b) Let Bluetooth Logger device connect to computer’s USB port through USB cable;
c) Computer will identify the device and build a com port for communication when you open
the COM tool;
d) After you selected the correct com port and settings, you can click “Open Port” button on
COM tool;
e) You can send commands to the Bluetooth Logger device through the COM tool.
For example as below:
You input the word of “LOGRQT” then click “Send Command” button.
Bluetooth Logger device will upload current all the records to the COM tool;
f)
Commands list:
Commands
SETNAM
SETPRD
SETMAX
SETMIN
SETADV
Application
Example & Explaining
SETNAM=1234
Set device ID
Set device ID as 1234
SETPRD=300
Set recording time
Recording once per 300 sec.
SETMAX=30
Set high temperature alarm threshold
Alarm over 30 degrees Celsius
SETMIN=-10
Set low temperature alarm threshold
Alarm below -10 degrees Celsius
SETADV=3
Set broadcasting time
Broadcasting once per 3 sec.
SETDBM=2
RF communication power is
0dbm;
SETDBM
Set RF communication power level
FLUSH
Clear memory data and recount time
CONMIN
Set min desired connect interval
CONMAX
Set max desired connect interval
LOGRQT
Upload current all the records
LOGALL
Upload before and current all the
records
Level parameters as below:
0 means -23dbm;
1 means -6dbm;
2 means 0dbm;
3 means 4dbm;
FLUSH=1
System clear memory data and
recount time
CONMIN=8
8*1.25 =10, The min desired
connect interval value is 10ms,
the parameter could be from 6 to
3200, the connect interval is
from 7.5ms to 4000ms.
CONMAX=16
16*1.25 =20, The max desired
connect interval value is 20ms,
the parameter could be from 6 to
3200, the connect interval is
from 7.5ms to 4000ms.
7. Upgrade the firmware
a) Please use the “cc debug” tool to upgrade firmware for the Bluetooth Logger device;
b) Please install “cc debug” program software on computer;
There are install file names as below:
SmartRF Flash Programmer 1.12.7.exe
c) Please download the new firmware to your computer;
The firmware file name like as below:
BLEThermoDataLog_v1.25.hex
d) Let the “cc debug” tool device connect to computer’s USB port through USB cable;
e) Let Bluetooth Logger device connect to “cc debug” tool through data line;
f) Please activate the “cc debug” program on your computer;
g)
h)
i)
j)
Please load the new firmware into “cc debug” program;
Please insure that “cc debug” tool connect Bluetooth Logger device is succeed;
Please select the correct settings;
When everything is all ready, the “cc debug” program interface with settings like as below:
k) Click “Perform actions” button, the firmware will be upgraded;
8. Technical Specifications
Temperature
Measurement Range
Temperature
Accuracy
Range
Temperature Resolution
-20°C to 60°C (Built-in normal battery)
-35°C to 70°C (Built-in special battery)
Accuracy:
+/- 0.5 °C (max) from -20°C to 60°C (Built-in normal battery)
+/- 0.5 °C (max) from -35°C to 70°C (Built-in special battery)
0.1°C/F over full temperature measurement range
Supported Devices
Android™ devices (Android4.3 above version)
Maximum wireless range
30 m unobstructed
Bluetooth frequency band
2.4 GHZ ISM Band
Bluetooth
Modulation Mode
frequency： 2402-2480MHz
transmitting power： <20 dBm
40 channels with 2 MHz spacing
• 3 fixed advertisting channels for
broadcasting
• 37 adaptively frequency hopped
dynamic data channels
GFSK
network protocol
BLE4.0
Topology
Point-to-point, Star
Memory
Housing size
Memory Depth 130,000 samples;
Time Offset + Temp, Status
Voltage： DC 2 - 3.6 V；
Current：Working < 80mA @ 3V；
Sleeping < 5uA @ 3V
68.8 L * 39.8 W * 14.5 H mm
Housing water proofness
IP54
Channel
Power range

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : 
Create Date                     : 2017:10:26 17:17:47+08:00
Creator                         : 
Modify Date                     : 2017:10:26 17:18:56+08:00
Producer                        : 福昕风腾PDF套件打印机 版本 7.2.0.0424
Subject                         : 
Title                           : 
Has XFA                         : No
Page Count                      : 13

EXIF Metadata provided by EXIF.tools