Emerson 1F97 1277 Users Manual 1277_37 7388A

White-Rodgers-1F97-1277-Emerson-Blue-12-Touchscreen-Single-Stage-Thermostat-Installation-And-Operation-Instructions-677013 white-rodgers-1f97-1277-emerson-blue-12-touchscreen-single-stage-thermostat-installation-and-operation-instructions-677013

1f971277 1555708d-85de-4161-a3cd-72ad98593f4c Emerson Thermostat 1F97-1277 User Guide |

2015-01-05

: Emerson Emerson-1F97-1277-Users-Manual-164400 emerson-1f97-1277-users-manual-164400 emerson pdf

Open the PDF directly: View PDF .
Page Count: 12

Download
Open PDF In Browser	View PDF

Big Blue Touchscreen Thermostat with
Automatic Heat/Cool Changeover Option
Installation and Operating Instructions for Model:

Save these instructions for future use!
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS
CAREFULLY BEFORE INSTALLING OR OPERATING THIS
CONTROL COULD CAUSE PERSONAL INJURY AND/OR
PROPERTY DAMAGE.

Model
1F97-1277

Programming Choices
Non-Programmable 5+1+1 Day

7 Day

APPLICATIONS
THERMOSTAT APPLICATION GUIDE

1F97-1277 Touchscreen Thermostat

Description
Heat Pump (No Aux. or Emergency Heat)
Heat Pump (with Aux. or Emergency Heat)
Systems with up to 3 Stages Heat, 2 Stages Cool
Heat Only Systems
Millivolt Heat Only Systems – Floor or Wall Furnaces
Cool Only Systems
Gas or Oil Heat
Electric Furnace
Hydronic (Hot Water) Zone Heat – 2 Wires
Hydronic (Hot Water) Zone Heat – 3 Wires
Wired Remote Temperature Sensor (Indoor/Outdoor)

Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes

Dual Fuel Feature (Heat Pump Mode)

Yes

SPECIFICATIONS
Electrical Rating:

Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . .
Input-Hardwire . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setpoint Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential (Single Stage) . . . . . . . . . . . . . . . . . . . . .
Differential (Multi-Stage) . . . . . . . . . . . . . . . . . . . . . .
Differential (Heat Pump) . . . . . . . . . . . . . . . . . . . . . .
Operating Ambient . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Humidity . . . . . . . . . . . . . . . . . . . . . . . . . .
Shipping Temperature Range . . . . . . . . . . . . . . . . . .
Dimensions Thermostat . . . . . . . . . . . . . . . . . . . . . .

! CAUTION
To prevent electrical shock and/or equipment damage,
disconnect electric power to system at main fuse or
circuit breaker box until installation is complete.

Index

Installation
Wiring Connections
Thermostat Quick Reference
Installer Configuration Menu
Operating Your Thermostat
Programming
Troubleshooting

Page
2
2
4
5
8
9
12

mV to 30 VAC, NEC Class II, 50/60 Hz or DC
20 to 30 VAC
1.5A per terminal, 2.5A maximum all terminals combined
45 to 99°F (7 to 37°C)
Heat 0.6°F; Cool 1.2°F
Heat 0.6°F; Cool 1.2°F
Heat 1.2°F; Cool 1.5°F
32°F to +105°F (0 to +41°C)
90% non-condensing max.
-4 to +150°F (-20 to +65°C)
4-9/16"H x 5-13/16"W x 1-3/16"D

ATTENTION: MERCURY NOTICE
This product does not contain mercury. However, this
product may replace a product that contains mercury.
Mercury and products containing mercury must not be
discarded in household trash. Do not touch any spilled
mercury. Wearing non-absorbent gloves, clean up any
spilled mercury and place in a sealed container. For proper
disposal of a product containing mercury or a sealed
container of spilled mercury, place it in a suitable shipping
container. Refer to www.thermostat-recycle.org for
location to send the product containing mercury.

PART NO. 37-7388A
www.white-rodgers.com
www.emersonclimate.com

1241

INSTALLATION

! WARNING
Thermostat installation and all components of the
control system shall conform to Class II circuits per
the NEC code.

Remove Old Thermostat

A standard heat/cool thermostat consists of three basic parts:
1. The cover, which may be either a snap-on or hinge type.
2. The base, which is removed by loosening all captive
screws.
3. The switching subbase, which is removed by unscrewing
the mounting screws that hold it on the wall or adapter
plate. Before removing wires from old thermostat,
label each wire with the terminal designation from
which it was attached. Disconnect the wires from the old
thermostat one at a time. Do not let wires fall back into
the wall.

5.
6.

2 "AA" alkaline batteries are included in the thermostat at
the factory with a battery tag to prevent power drainage.
Remove the battery tag to engage the batteries.
To replace batteries, set system to OFF, remove thermostat
from wall and install the batteries in the rear along the top of
the thermostat (see Figure 1).
Figure 1 – Thermostat Base Multi-Stage 1F97-1277

Mounting
Hole

S
-

W/E

Place Level
across
Mounting Tabs
(for appearance only)

Rear view of thermostat

Installing New Thermostat

Battery Location

Pull the thermostat body off the thermostat base. Forcing
or prying on the thermostat will cause damage to the unit.
Place base over hole in wall and mark mounting hole
locations on wall using base as a template.
Move base out of the way. Drill mounting holes. If you
are using existing mounting holes and the holes drilled
are too large and do not allow you to tighten base snugly,
use plastic screw anchors to secure the base.
Fasten base snugly to wall using mounting holes shown
in Figure 1 and two mounting screws. Leveling is for
appearance only and will not affect thermostat operation.
Connect wires to terminal block on base using appropriate
wiring schematic (see diagrams on next page).
Push excess wire into wall and plug hole with a fire resistant material (such as fiberglass insulation) to prevent
drafts from affecting thermostat operation.
Carefully line the thermostat up with the base and snap
into place.

2 "AA" Batteries

WIRING CONNECTIONS
Refer to equipment manufacturers' instructions for specific
system wiring information. After wiring, see CONFIGURATION section for proper thermostat configuration.

For wiring diagrams, see next page.
Wiring diagrams shown are for typical systems and describe
the thermostat terminal functions.

TERMINAL DESIGNATION DESCRIPTIONS
Terminal Designation

Description

B . . . . . . . . . . . . . . . . . . .
O . . . . . . . . . . . . . . . . . . .
Y . . . . . . . . . . . . . . . . . . .
G . . . . . . . . . . . . . . . . . . .
RC . . . . . . . . . . . . . . . . . .
RH . . . . . . . . . . . . . . . . . .
C . . . . . . . . . . . . . . . . . . .
L . . . . . . . . . . . . . . . . . . .
6 . . . . . . . . . . . . . . . . . . .
W . . . . . . . . . . . . . . . . . . .
- . . . . . . . . . . . . . . . . . . .
S . . . . . . . . . . . . . . . . . . .
+ . . . . . . . . . . . . . . . . . . .

Changeover valve for heat pump energized constantly in heating
Changeover valve for heat pump energized constantly in cooling
Compressor Relay
Fan Relay
Power for Cooling
Power for Heating
Common wire from secondary side of cooling
For Call for Service indicator for systems with diagnostic connection
Powered closed connection for 3-wire zone valve
Heat Relay
Common (DC) for wired remote temperature sensor
Frequency signal from remote temperature sensor
Power (DC) to remote temperature sensor

WIRING CONNECTIONS
Single Stage Connections

Single stage gas, oil or electric.

Refer to equipment manufacturers' instructions for specific system
wiring information.
This thermostat is designed to operate a single-transformer or twotransformer system.
You can configure the thermostat for use with the following systems:

HEAT PUMP TYPE 1 (HP 1). Single stage compressor system; gas
or electric backup.
After wiring, see INSTALLER CONFIGURATION section for proper
thermostat configuration.

Single Stage System with Single Transformer

{

To Remote Temperature Sensor
Jumper

Energized in
Cool
Mode

Energized
on call
for Cool
(Compressor)

24 Volt
(Hot)
Cool

24 Volt
(Hot)
Heat

24 Volt
Common
(optional)

DC
supply
voltage
to remote
Temperature
Sensor

Remote
Temperature
Sensor
signal

Third
wire for
3-wire
zone
valve

Diagnostic
Indicator
(See
Note 1 )

System

Single
Stage
(SS)

Energized
in Heat
or Off
Mode

Blower/
Circulator Fan
Energized on
call for
Cool &
for Heat
(if ELE
is selected)

DC
Return
to
Energized
Remote on call for
Temp- Heat
erature
Sensor

NEUTRAL
120VAC

24VAC
HOT

*Common connection required for fault or
malfunction indication and remote sensor.

CLASS II
TRANSFORMER

Single Stage with Two Transformers

To Remote Temperature Sensor
Jumper

{

Remove Jumper Wire
between RH & RC

24 Volt
(Hot)
Heat

24 Volt
Common
(optional)

DC
supply
voltage
to remote
Temperature
Sensor

Remote
Temperature
Sensor
signal

System

Single
Stage
(SS)

Energized
in Cool
Mode

Energized
in Heat,
Off Mode

Energized
on call
for Cool
(Compressor)

Blower/
Circulator Fan
Energiz24 Volt
ed on
call for (Hot)
Heat or Cool
Cool
(if ELE
is selected)

DC
Return
to
Energized
Remote on call for
Temp- Heat
erature
Sensor

Third wire Diagnostic
for 3-wire Indicator
zone valve (See
Note 1 )

NOTE: If continuous backlight or hardwired
power input are desired but do not function
in both HEAT and COOL modes, cut the
heating transformer 24V wires and tape off.
Connect the neutral circuit disconnected
from the heating transformer to the neutral
circuit of the cooling transformer. Disconnect the wire to the RH terminal and install
a jumper between RH and RC. Depending
on the system requirements, replace the
cooling transformer with a 75VA class II
transformer if needed.

NEUTRAL
24VAC

NEUTRAL
120VAC

120VAC

HOT

24VAC
HOT

COOLING
CLASS II
TRANSFORMER

*Common connection required for fault or
malfunction indication and remote sensor.

HEATING
CLASS II
TRANSFORMER

Heat Pump Systems

{

To Remote Temperature Sensor
Jumper

Remote
Temperature
Sensor
signal

DC
Return
to
Remote
Temperature
Sensor

Auxiliary &
Emergency
Heat
1st
Stage

Power
Closed
Connection
for
3-wire
zone
valve

*24 VAC common connection
optional for system operation.

System

Energized in
Heat
Heat/
Pump 1
Emer(HP1)
gency
Mode

1st
Stage
Energized
Heat
in Cool
& Cool
& Off
(ComMode
pressor)
**

Blower/
Circulator Fan
24 VAC 24 VAC 24 VAC
Energiz(Hot)
(Hot)
Common
ed on
Cool
Heat
(optional)
call for
Heat or
Cool

DC
supply
voltage
to remote
Temperature
Sensor

Diagnostic
Indicator
(See
Comfort
Note )
Alert II module
or similar
malfunction
module

Required for fault or malfunction indication, remote temperature sensor, or
for continuous backlight operation.
**Dual fuel de-energizes
compressor when auxiliary heat is
energized.

NEUTRAL
24VAC

120VAC

HOT
CLASS II
TRANSFORMER

NOTE ➀: Connection for Call for Service diagnostic indicator compatible with mechanical or electronic condenser control with Comfort AlertTM.

THERMOSTAT QUICK REFERENCE
Home Screen Description

Figure 2 – Home Screen Display
Room
Temperature

Day of Week

Set Temperature

Time of Day

Temperature
UP/Down used for
modifying set point
as well as to
navigating the menus

System
Switch

Fan
Switch

Enters user-friendly
program into
the schedule

Indicates when
thermostat is calling
for Heat or Cool

Menu key for entering
different modes such as
Configuration, Set Time,
Set Schedule and Cleaning

Battery Level Indicator
Indicating the current power level
of the 2 “AA” batteries.
Full power remaining.
Half power remaining.
Change
The batteries should be replaced at this time.

Programming and Configuration Items
1 Displays and "Keypad Lockout" when in keypad
lockout mode.
Displays and "Temperature Limit" and "Keypad
Lockout" when limited range is activated and locked.
Displays only "Temperature Limit" when limited range
is activated.

Figure 3 – Programming & Configuration Items
16

2 Indicates period of day being programmed.

3 RUN SCHEDULE (run program) button.

8
14

4 SET TIME button or HOLD temperature button.
5 Displays "Change Filter" when the system has run

15
12

for the programmed filter time period as a reminder to
change or clean your filter.

6 COPY button or INSTALLER CONFIG button.

7 CLEAN DISPLAY button allows 30 seconds to wipe off

the display or ADVANCE DAY button for programming.

8 Used in programming to set time and in configuration

menu to change selections.

9 "Hold Until" indicates the time when a temporary hold
period will end.

13 "System On" indicates when heating or cooling stage

10 "Hours" and "Days" displays during steps in installer

14 "Copy" indicates the copy program feature is being

11 The words "Hold At" are displayed when the thermo-

15 A steady "Cool Savings" display indicates the feature

configuration.

stat is in the HOLD mode. "Temporary Hold At" is
displayed when the thermostat is in a temporary HOLD
mode.

12 "Call For Service" indicates a fault in the heating/cool-

ing system. It does not indicate a fault in the thermostat.

is energized.

used during programming.

is enabled in the installer menu. A flashing "Cool Savings" display indicates the feature is active.

16 "Remote" indicates that the indoor remote temperature
sensor, is being accessed. "Outdoor Remote" indicates the outdoor remote temperature sensor is being
accessed.

INSTALLER/CONFIGURATION MENU
To enter the menu: Press the Menu touch key. Press and hold for 5 seconds the Installer Config touch key. This displays
menu item #1 in the table below. Press
to advance to the next menu item or
to return to a previous menu item. Press
or
to change a menu item.
Installer Note: To default the programming, clock and Configuration Menu to the Factory Default Settings, press the ,
and SYSTEM keys simultaneously. The thermostat display will go blank for a few seconds, and then all segments will display
momentarily. For heat pump systems, Configuration Menu item 1 must be set to match the heat pump system.
If first item does not show SS1 or HP1, you have an earlier thermostat model and need Instruction Sheet 37-6814D.
CONFIGURATION MENU
Menu
NonReference Program- Program- Press
Number
mable
mable
Button
1

Displayed
(Factory
Default)
SS1

Press
or
to
select from listed
options
Comments
HP1, SS1

Selects Single Stage or Heat Pump

(ELE)

GAS

(1 compressor)
GAS setting: furnace controls blower

Days, (7) P

5+1+1 or 0

PS (4)

ELE setting: thermostat controls blower
Programs per week. (0 = non-programmable)
Program periods per day
4 = Morning, Day, Evening, Night

Cool-OffHeat-Auto
Cool-Off-HeatEmer-Auto

2 = Day, Night
Cool-Off-Heat,
System switch configuration in single stage
Off-Heat, Cool-Off
Cool-Off-Heat-Emer, System switch configuration, heat pump mode
Off-Heat-Emer,
Cool-Off
OFF
Selects Energy Management Recovery, E (with programming option on)

E (On)

Cr, Heat (FA)

Selects Adjustable Anticipation, cycle rate, Heat

Cr, Cool (FA)

Selects Adjustable Anticipation, cycle rate, Cool

Cr/AU, Emer (FA)

Selects Adjustable Anticipation, cycle rate auxiliary, (This item is

CL (OFF)

only to appear if HP1 is selected above)
Selects Compressor Lockout

dL (On)

OFF

dL (LO)

4, LO to 4, HI

°F

°C

b (On)

OFF

dS (On)

OFF

Selects Daylight Saving Time calculation

AS, Heat (On)

OFF

Selects Automatic Schedule for comfort temperature Programming,

AS, Cool (On)

OFF

heat mode
Selects Automatic Schedule for comfort temperature Programming,

1-2-3-4-5-6
62-98

TEMPERATURE LIMIT, HEAT (max. heat set point)

46-82

TEMPERATURE LIMIT, COOL (min. cool set point)

CS, (OFF)
Cool Savings
HL, Heat (99)

LL, Cool (45)

OFF,
Keypad Lockout

Selects Continuous Display backlight & intensity
Selects Backlight Intensity
Selects Adjustable Ambient Temperature Display [range -4 (LO)
to +4 (HI)]
Selects °F/°C Display (temperature units in Fahrenheit or Celsius).
Selects audible Beeper On/Off

cool mode
Selects Cool Saving Feature & amount

L (total), P (partial), Selects Keypad Lockout
Temperature Limit
(limited temperature
range)

000

001-999
OFF

Selects Keypad Lockout Combination (active only if keypad Lockout
is selected).
Fast second stage of heat (not available if SS1 is selected above)

FS, Heat (On)

Remote (OFF)

In, Remote

Outdoor Remote

LS (On)

OFF

Local temp. Sensor enable/disable (only when Indoor Remote is

dF (5)

5-50

selected On).
Selects Dual Fuel Feature & set point (in Fahrenheit)

Cd (60)

0-99

(applicable only when HP1 is selected)
Selects Compressor delay in seconds (only when dF is selected >5)

Change Filter
(OFF)
200 Hours

Selects Change filter feature

25-1975
(in increments
of 25 hours)

Change filter, duration hours

Remote temperature sensor, enable/disable
Remote temperature sensor (Indoor/Outdoor)

INSTALLER/CONFIGURATION MENU
1)

This control can be configured for:
SS1 – Single Stage System
HP1 – Heat Pump with one stage of compressor
(2 heat/1 cool)
(Dual Fuel see menu item 25)
GAS or Electric (ELE) fan operation. If the heating
system requires the thermostat to energize the fan,
select ELE. Select GAS if the heating system energizes
the fan on a call for heat. Note: Resetting the thermostat switches the option to ELE.
3) Programs per week – This control can be configured for

7 independent day or 5+1+1 day programming or non-
programmable modes. Default is 7-day mode. The
display indicates "7 Days" as default. Other options "5
Days" or "0 Days" can be selected by pressing touch
keys,
or . If "0 Days" is selected for non-programmable mode, the step for EMR will be skipped, as this
feature will not be available in this mode.
4) Program Steps per day – This control can be configured
for 4 or 2 program steps per day. Default is "4 PS" and
can be toggled between 4 PS and 2 PS by pressing
the
or
touch keys.
5) System Switch Configuration (SS1/HP1) – This thermostat is configured for Heat and Cool with Auto changeover default (Cool-Off-Heat-Auto). Can be configured as
Heat & Cool (Cool-Off-Heat), or Heat Only (Off-Heat), or
Cool Only (Cool-Off).

When the control is in heat pump configuration (HP1), the
system switch configuration will have an additional mode
available namely, Emer for Emergency Mode.
6) Energy Management Recovery (EMR) – (this step is

skipped if configured as non-programmable).

When set to "On" causes the thermostat to start heating

or cooling early to make the building temperature reach

the program setpoint at the time you specify.
Example: Let us say, the heating program is 65°F at
night and 70° at 7 AM. If the building temperature is 65°F,
the difference is 5°F. Allowing 5 minutes per °F rise, the
thermostat setpoint will change to 70° at 6:35 AM.
Cooling allows more time per °F, because it takes
longer to reach temperature.
7, 8 & 9) Cycle Rate Selection – The factory default setting
is fast cycle (FA Cr) in all modes (Heat, Cool, Emer). To
slow cycling (SL, Cr), press touch keys
or
toggle

between FA & SL. The cycle rates are as below different
selections:

Mode
Fast rate
Slow rate
Heat
0.6°F
1.2°F
Cool
1.2°F
1.7°F
Emer
1.2°F
1.7°F
10) Select Compressor Lockout (CL) – Selecting CL On
will cause the thermostat to wait 5 minutes between
cooling cycles. This is intended to help protect the
compressor from short cycling. Some of the newer
compressors have already got a time delay built in and
do not require this feature to be activated in the thermostat. Your compressor manufacturer can tell you if this
lockout feature is already present in their system. When
the thermostat compressor time delay is activated, it will
flash the set point for up to five minutes.
11) Select Continuous Backlight – In low lighting conditions, display backlight improves the display contrast.
When C terminal is connected, selecting dL On will turn

the backlight on continuously. Selecting dL Off will turn
the backlight on momentarily after any key is pressed.
When C terminal is not powered (battery only), dL On
enables the momentary backlight whenever a key is
pressed.
12) Select Backlight Intensity – This thermostat has the

ability to provide two selectable intensities of the back
light: HI and LO. Using
or
touch keys you can

toggle the selection between HI and LO.
13) Select Temperature Display Adjustment 4 LO to 4 HI

This allows you to adjust the room temperature display

by an amount in the range of -4°F to +4°F in 1° steps by

using the
or
touch keys. Your thermostat was

accurately calibrated at the factory, however you have the

option to change the display temperature value to match

your previous thermostat, if you so prefer.
14) Select °F or °C Readout – Select the desired temper
ature unit by pressing
or . Factory default is °F.
15) Select Audio Prompting (Beeper) On or Off – Factory

default setting is on (b, On). If you wish to turn off the

beeper select OFF.
16) Select Daylight Saving Time Calculation – This feature

will allow the thermostat to calculate the DST automatically and apply it to the Real Time Clock display. Default

On. Use
or
touch keys to select the feature, OFF.
17 & 18)Select Automatic Schedule – This feature allows
programming a “Comfort Temperature” into all program
periods with the Auto Schedule key. When Heat AS (for
Heat mode) or Cool AS (for Cool mode) is selected On,

the Auto Schedule feature is ready to be set. Off indicates that the feature is not ready to be used or a
“Comfort Temperature is already set. See Auto Schedule
in Programming section.
19) Select Cool Savings™: With Cool Savings™ enabled,

the thermostat will make small adjustments to the

setpoint temperature during periods of high demand to

reduce AC system running time and save energy. When

the cooling system has been running for more than 20

minutes, humidity in the home will be lower and a higher

temperature will feel comfortable. After 20 minutes of run

time, the thermostat will start increasing the setpoint
temperature in steps of less than one degree as the

system continues to run. These adjustments will eventually cause the system to satisfy the thermostat to turn the

system off and reduce the energy consumption. When

the Cool Savings™ feature is active and making adjustments, the display will flash “Cool Savings”. The
amount of the adjustments to the setpoint temperature
is dependent on the Cool Savings™ value that is set, 1
being the least adjustment and 6 being the most adjustment. With this feature set to OFF, no change will occur
when the AC system is continuously running during the
periods of high demand. Periods of high demand will normally occur during the late afternoon and early evening
on the hottest d
ays of the summer. As demand lessens
the adjustments t o setpoint temperature are reversed
until setpoint temperature returns to normal and “Cool
Savings” no longer flashes.

INSTALLER/CONFIGURATION MENU
20) Heat Temperature Limit Range – This feature adjusts
the highest setpoint temperature for heat. The default
setting is 99°F. It can be changed between 62°F and
98°F by pressing the
or
key. The "temperature
limit" icon will be displayed to the left of your setpoint
temperature when using this feature. The "temperature
limit" icon will flash if an attempt is made to adjust the
temperature beyond the range selected.
21) Cool Temperature Limit Range – This feature adjusts
the lowest setpoint temperature for cool. The default
setting is 45°F. It can be changed between 46°F and
82°F by pressing the
or
key. The "temperature
limit" icon will be displayed to the left of your setpoint
temperature when using this feature. The "temperature
limit" icon will flash if an attempt is made to adjust the
temperature beyond the range selected.
22) Keypad Lockout – This step allows you to select the
type of lockout or limited range security required. If no
lockout or limited range security is required, press
to
advance the menu.
Three security settings are available in this menu item.
Use the
or
keys to select the lockout desired.
Lockout selections are:
"Keypad Lockout and L" = Total Lockout. Total Lockout
locks all keys.
"Keypad Lockout and P" = Partial Lockout. Partial Lock out allows only the
or
keys to operate within your
set temperature limits.
"Temperature Limit/Keypad Lockout" prevents
changing the temperature limits in the Configuration
Menu.
Keypad Lockout Combination Number Selection
Display will read "OFF" "Keypad Lockout".
Skip this step and continue through the configuration
menu items 23 thru 26 if you require an Air Filter Change
out indicator or Humidifier Pad Change out indicator by
pressing the
button to advance.
Return to this point when you are ready to start your
selected lock-out and continue by:
Pressing
or
keys to select ON.
Press . Display will read "000".
Pressing
or
keys to select your keypad lockout
combination number. Note: "000" is not a valid
combination choice.
Record the number you select for future use.
Press
to exit the menu. The security feature you
select will start in 10 seconds. The system button will
remain active for 10 seconds to allow setting Heat, Off,
Cool or Auto.

23 Select Fast Second Stage ON or OFF – In the run
mode, with the fast Heat feature enabled (FA Heat On), if
the Heat setpoint temperature is manually raised by 3°F
(2°C) or more above the actual temperature using
the
second stage will energize immediately. With FA OFF,
second stage will not energize until the setpoint temperature is 1°F or more above actual temperature for more
than ten minutes. The Fast Cool feature (FA Cool) provides the same controls when the setpoint temperature is
lowered.
24) Select Remote Temperature Sensor – This control
allows one wired remote temperature sensor (indoor,
F145-1328, or outdoor, F145-1378) be connected to it
and indicates the measured temperature in clock digits.
This menu enables you to select the remote sensor and
also configure it as indoor or outdoor temperature sensor.
Factory default is off. Select Remote On and Remote in
(for indoor) or Outdoor Remote.
Local Temperature Sensor disable – This is applicable
only when indoor remote temperature sensor is enabled.
Factory default is On LS. You can make it Off LS if you
desire by using
or
touch keys. Then, only the
indoor remote temperature reading will be used for
control.
25) Select Dual Fuel Feature and Setpoint – This feature is
applicable only in heat pump modes. An outside remote
sensor must also be installed. When the outside tem perature falls below the selected setpoint temperature,
dF, the thermostat will switch to gas heat and shut down
the compressor. Use the
or
keys to select the
desired setpoint temperature in the range of 5 to 50.
Factory default is 5, which disables this feature. See
Dual Fuel Temperature and Setpoint in Programming
section.
Select Compressor Delay – When dF is enabled, the
shut down of the compressor(s) is delayed for a time
period after the auxiliary stage is energized. This delay,
Cd, is factory set at 60, but can be set in the range of 0
to 99.
26) Select Change Filter Run Time – The thermostat
will display "Change Filter" after a set time of blower
operation. This is a reminder to change or clean your air
filter. This time can be set from 25 to 1975 hours in 25
hour increments. A selection of OFF will cancel this
feature. When "Change Filter" is displayed, you can
clear it by pressing Clean Display. In a typical application,
200 hours of run time is approximately 30 days.

OPERATING YOUR THERMOSTAT
Choose the Fan Setting (Auto or On)

Fan Auto is the most commonly selected setting and runs the
fan only when the heating or cooling system is on.
Fan On selection runs the fan continuously for increased air
circulation or to allow additional air cleaning.

Choose the System Setting
(Cool, Off, Heat, Emer, Auto)

Press the SYSTEM button to select:
Heat: Thermostat controls only the heating system.
Off: Heating and Cooling systems are off.
Cool: Thermostat controls only the cooling system.
Auto: Auto Changeover is used in areas where both heating
and cooling may be required on the same day. AUTO allows
the thermostat to automatically select heating or cooling
depending on the indoor temperature and the selected heat
and cool temperatures. When using AUTO, be sure to set the
Cooling temperatures more than 1° Fahrenheit higher than
the heating temperature.
Emer: Setting is available only when the thermostat is configured in HP1 mode.

Manual Operation for
Non-Programmable Thermostats

Press the SYSTEM button to select Heat or Cool and use
the
or
buttons to adjust the temperature to your
desired setting. After selecting your desired settings you can
also press the SYSTEM button to select AUTO to allow
the thermostat to automatically change between Heat
and Cool.

IMPORTANT!
Manual Operation (Bypassing the Program)
Programmable Thermostats

Press
or
and the HOLD button and adjust the temperature wherever you like. This will override the program. The
HOLD feature bypasses the program and allows you to adjust
the temperature manually, as needed. Whatever temperature
you set in HOLD will be maintained 24 hours a day, until you
manually change the temperature or press Run Schedule to
cancel HOLD and resume the programmed schedule.

Program Override (Temporary Override)

Press
or
buttons to adjust the temperature. This will
override the temperature setting for a (default) four hour override period. The override period can be shortened by pressing
or lengthened by pressing . Program Override period
can range from 15 minutes to 7 days.
Example: If you turn up the heat during the morning program,
it will be automatically lowered later, when the temporary hold
period ends. To cancel the temporary setting at any time and
return to the program, press Run Schedule.
If the SYSTEM button is pressed to select AUTO the
thermostat will change to Heat or Cool, whichever ran last. If
it switches to heat but you want cool, or it changes to cool but
you want heat, press both
or
buttons simultaneously to
change to the other mode.

PROGRAMMING
Set Current Time and Day

1) Press Menu key to enter installer menu. Then press

Set Time once to indicate hour & A or P designation in

clock display.
2) Press and hold either the
or
touch key until you

reach the correct hour and A or P designation.
3) Press Set Time again to display minutes only in clock
display.
4) Press and hold either the
or
touch keys until you

reach the correct minutes.
5) Press Set Time once again to display year.
6) Press and hold either the
or
touch key until you

reach the correct year.
7) Press Set Time once again to display month.
8) Press and hold either the
or
touch key until you

reach the correct month.
9) Press Set Time once again to display date of the month

along with day of the week at top row (which is automatic).
10) Press and hold either the
or
touch key until you

reach the correct day of the month and day of the week

is automatically calculated and displayed at the top row.
11) Press Run Schedule once; now the display will show the

correct time and room temperature.

Automatic Daylight Saving Calculation

The Real Time Clock will adjust automatically for daylight savings time, in the following manner:
Increment one hour at 2 AM on the second Sunday of March
and decrement one hour at 2 AM on the first Sunday of November. (New DST effective 2007).
The daylight saving feature can be enabled or disabled in
installer configuration mode. Default is dS ON (enabled).
After entering installer configuration mode, momentarily
press
or
touch key until the display indicates dS (in
actual temperature digits) and on (default – in clock digits).
and
keys will toggle display and operation from on to
OFF.

Programming Tip: Copy Button

You may copy any daily program to another day or group
of days by pressing the Copy button. In 7 day programming
mode when the Copy button is pressed, the other 6 days
of the week will flash. To copy the current program into the
remaining six days, simply press the Copy button again. To
copy the current program to another day of the week, press
Advance Day to select the day and press Copy to paste the
program. In 5+1+1 day programming mode the copy function
is similar. The weekday (Mon-Fri) program can be copied to
Sat and Sun (both flashing) or use Advance Day to choose
Sat or Sun and press the Copy button to paste the program.

PROGRAMMING
Fill in the blank schedule on the next page then:

Enter the Heating Program

1) Press the Menu button and then press Set Schedule.
Press SYSTEM button to select either "Heat" or "Cool"
in the system switch area indicating the active mode being
programmed. You can switch to the other mode by pressing the system switch at any time.
2) The top of the display will show the day(s) being programmed. The time and set at temperature are also
displayed. "Morning" will also be displayed to indicate
the period.
3) Press
or
key to change the temperature to your
selected temperature for the 1st heating period (Morning).
4) Press
or
key to adjust the start time for period.
The time will change in 15 minute increments.
5) Press FAN to select Auto or Prog.
6) After you have set the time and the temperature for the
period to begin, press Set Schedule to advance to the
next program period.
7) Repeat steps 2 through 6 until all of the program times
and temperatures are set for all program periods on
that day.
8) Press "Advance Day" to change to the next day and
repeat steps 2 through 8.
9) When programming is complete and all of the times and
temperatures match your desired heating schedule, press
Run Schedule. The thermostat will now run your program.

Enter the Cooling Program

1) Press the SYSTEM button until the Cool icon appears.
2) Follow Enter Heating Program instructions for entering
cooling times and temperatures.

Automatic Schedule

This feature provides a method to program every day with
the most popular time and temperature profile using one key
press. For this feature to be available, the Auto schedule options (AS Cool or AS Heat) should be set on in the installer
configuration.
Select the desired “Comfort Temperature” in the setpoint.
When the Auto Schedule touch key is pressed, it will start
flashing indicating that it is now ready to insert the displayed
temperature setpoint as the “Comfort Temperature” for the
selected system mode currently in (Heat/Cool). A second
press of the Auto Schedule touch key will complete the
process. A 6 o F setback temperature will also be inserted for
the night step. Once it is done, the touch key display Auto
Schedule will disappear disabling any further operation of
Auto Schedule touch key. If desired it can be enabled again
in the installer configuration menu.

Entering Fan Program

In the Set Schedule mode, the FAN key is used to select the
fan operation during a program period. The default state of
the Fan key is FAN Auto (fan runs during a call for cool but
not on a call for heat). It can be changed to FAN Prog (fan
runs during a program period). Each press of the FAN key will
change the mode of the fan between Auto and Prog.
In the Run mode, when a program period that has FAN Prog
begins, the fan will turn on and stay on during the complete period. The display will show FAN On Prog. Pressing
the FAN key will change FAN On Prog to On (fan running
continuously) or Auto. To return to FAN On Prog, press Run
Schedule.

PROGRAMMING
Energy Saving Factory Pre-Program

The 1F97-1277 thermostats are programmed with the energy saving settings shown in the table below for all days of the week.
If this program suits your needs, simply set the thermostat clock and press the RUN button.
The table below shows the factory set heating and cooling schedule for all days of the week.

Heating
Program
Cooling
Program

*Wake Up
(Morning)
6:00 AM
70°F

Leave For Work
(Day)
8:00 AM
62°F

*Return Home
(Evening)
5:00 PM
70°F

Go To Bed
(Night)
10:00 PM
62°F

6:00 AM

8:00 AM

5:00 PM

10:00 PM

78°F

85°F

78°F

82°F

* You can eliminate these two program periods in the configuration menu (reference #4) if the building is occupied all day.
Day will change to 6:00 am and can be programmed as required.

Planning Your Program – Important

The Heating and Cooling Program schedules below allow you to pencil in your own program times and temperatures.
The 1F97-1277 comes configured for 7 day programming and can also be configured for 5+1+1 programming
(see configuration section).
Factory settings are listed on Monday, Saturday and Sunday. If you are re-programming a 5+1+1 day schedule,
pencil in your own times and temperatures directly below the factory times and temperatures.
If you are re-programming a 7 day fill in all lines with the times and temperatures you want.
Keep the following guidelines in mind when planning your program.
• In Heating, lower temperatures will save energy.
• In Cooling, higher temperatures will save energy.
• If you plan on using Auto Changeover, do not program the heating higher than the cooling.

Worksheet for Re-Programming 5+1+1 and 7 Day Program
Heating
Program
MON

Wake Up
(Morning)

Fan

Leave For Work
(Day)
Fan

Return Home
(Evening)

Fan

Go To Bed
(Night)

Fan

6:00 AM

70°F

Auto 8:00 AM

62°F Auto 5:00 PM

70°F

Auto 10:00 PM 62°F Auto

6:00 AM

70°F

Auto 8:00 AM

62°F Auto 5:00 PM

70°F

Auto 10:00 PM 62°F Auto

6:00 AM

70°F

Auto 8:00 AM

62°F Auto 5:00 PM

70°F

Auto 10:00 PM 62°F Auto

TUE
WED
THU
FRI
SAT
SUN
Cooling
Program
MON

Wake Up
(Morning)

Fan

Leave For Work
(Day)
Fan

Return Home
(Evening)

Fan

Go To Bed
(Night)

Fan

6:00 AM

78°F

Auto 8:00 AM

85°F Auto 5:00 PM

78°F

Auto 10:00 PM 82°F Auto

6:00 AM

78°F

Auto 8:00 AM

85°F Auto 5:00 PM

78°F

Auto 10:00 PM 82°F Auto

6:00 AM

78°F

Auto 8:00 AM

85°F Auto 5:00 PM

78°F

Auto 10:00 PM 82°F Auto

TUE
WED
THU
FRI
SAT
SUN

PROGRAMMING
Wired Remote Temperature Sensing

Weight of Remote Reading:

Once in the installer configuration mode, momentarily press
the
or
touch key until display indicates Remote (at the
top left of the LCD) and OFF (default – in clock digits).
Pressing
or
touch key will toggle the operation and
display from Remote OFF to Remote On.
When Remote On is selected, press
key for the display to
indicate Remote In (for indoor remote).
The
or
keys will toggle the operation and display from
Remote In to Outdoor Remote.
When any remote is selected the temperature will display in
the clock digits for one second alternating with the current
time for three seconds when in Run Schedule mode.
Outdoor Remote will indicate at the top left of display for
outdoor remote reading.
Only Remote will show at top left for indoor remote reading.
(oF or oC will not indicate with remote temperature readings).

When Remote In is selected (with Remote selected to On),
press
key for the display to indicate the status of the local
sensor LS On (default for thermostat local sensor operational). The
and
keys will toggle the function and display
from LS (shown in actual temperature digits) and On (shown
in clock digits) to LS OFF to designate the local sensor is
disabled.

One remote temperature sensor can be installed indoor or
outdoor and connected to the thermostat by a maximum
cable length of 100 meters (300 ft). Three terminals, +, S & are provided on the terminal block to connect to the WhiteRodgers standard wired remote sensor. This sensor will be
read by the thermostat only when 24VAC is present.
When used as indoor sensor, the readings can be weighted
with the local sensor for specific program periods. User can
enable or disable the remote sensor in the installer configuration mode and also the outdoor temperature can be selected
to show on the display.

Sensing Range:
Outdoor temperature range is -40 to 140oF
Indoor temperature range is 32 oF to 99 oF

When in view schedule mode the weight of the indoor remote
sensor will be shown in the left actual temperature digits designated as A2 (default for average weight), H4 (high weight)
or L1 (low weight). The period (Morning, Day, Evening, Night)
will also be shown to the right of the weight value in the actual
temperature digits.
When in view schedule mode, press
and
keys at the
the same time to sequence the indoor remote temperature
sensor weight from A2 to H4 to L1 and back to A2 for each
of the program period times for each day. (The H4 weight is
twice the weight of A2 and A2 is twice the weight of L1).

The local sensor may be disabled only if the indoor remote
sensor is enabled and functional.
If the indoor remote sensor is disabled or not functional, the
local sensor will automatically enable and display in the run
schedule mode.
The actual temperature displayed in the run mode is the
mathematical weighted sum of the two temperature sensors –
local and indoor remote.
(Outdoor remote sensor is not used for this computation).
If the remote sensor is absent or not enabled then the actual
temperature will be as measured by the local sensor.

TROUBLESHOOTING
Reset Operation

Note: When thermostat is reset, installer configuration menu settings and programming will reset to factory settings.
If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by removing
the wires from terminals R and C (do not short them together) and removing batteries for 2 minutes. After resetting the thermostat, replace the
wires and batteries. If the thermostat has been reset and still does not function correctly contact your heating/cooling service person or place
of purchase.

Symptom

Possible Cause

Corrective Action

No Heat/No Cool/No Fan
(common problems)

1. Blown fuse or tripped circuit breaker.
2. Furnace power switch to OFF.
3. Furnace blower compartment door or
panel loose or not properly installed.
4. Loose connection to thermostat or system.

Replace fuse or reset breaker.
Turn switch to ON.
Replace door panel in proper position to engage
safety interlock or door switch.
Tighten connections.

No Heat

1. Pilot light not lit.
2. Furnace Lock-Out Condition. Heat
may also be intermittent.

Re-light pilot.
Many furnaces have safety devices that shut down
when a lock-out condition occurs. If the heat works
intermittently contact the furnace manufacturer or
local HVAC service person for assistance.
Diagnostic: Set SYSTEM Switch to HEAT and
raise the setpoint above room temperature. Within
a few seconds the thermostat should make a soft
click sound. This sound usually indicates the thermostat is operating properly. If the thermostat does
not click, try the reset operation listed above. If the
thermostat does not click after being reset contact
your heating and cooling service person or place of
purchase for a replacement. If the thermostat clicks,
contact the furnace manufacturer or a HVAC service
person to verify the heating is operating correctly.

3. Heating system requires service or
thermostat requires replacement.

No Cool

1. Cooling system requires service or
thermostat requires replacement.

Same as diagnostic for No Heat condition except
set the thermostat to COOL and lower the setpoint
below the room temperature. There may be up to
a five minute delay before the thermostat clicks in
Cooling.

Heat, Cool or Fan
Runs Constantly

1. Possible short in wiring.
2. Possible short in thermostat.
3. Possible short in heat/cool/fan system.
4. FAN Switch set to Fan ON.

Check each wire connection to verify they are not
shorted or touching together. No bare wire should
stick out from under terminal block. Try resetting
the thermostat as described above. If the condition
persists the manufacturer of your system or service
person can instruct you on how to test the Heat/
Cool system for correct operation. If the system
operates correctly, replace the thermostat.

Thermostat Setting &
Thermostat Thermometer
Disagree

1. Thermostat thermometer setting
requires adjustment.

The thermometer can be adjusted +/- 4 degrees.
See Temperature Display Adjustment in the Configuration Menu section.

Furnace (Air Conditioner)
Cycles Too Fast or Too Slow
(narrow or wide
temperature swing)

1. The location of the thermostat and/or
the size of the Heating System may
be influencing the cycle rate.

Digital thermostats provide precise control and
cycle faster than older mechanical models. The
system turns on and off more frequently but runs for
a shorter time so there is no increase in energy use.
If you would like an increased cycle time, choose
SL for slow cycle in the Configuration menu, step 7
(heat) or 8 (cool). If an acceptable cycle rate is not
achieved, contact a local HVAC service person for
additional suggestions.

Forgot Keypad
Lockout Code

Press the menu button (button will disappear) and
hold in for 20 seconds. This unlocks the thermostat.

First item in Configuration
Menu is not SS1 or HP1

Earlier model of thermostat refer to 37-6814D.

White-Rodgers is a business
of Emerson Electric Co.
The Emerson logo is a
trademark and service mark
of Emerson Electric Co.

www.white-rodgers.com
www.emersonclimate.com

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Page Count                      : 12
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:d3106947-43d6-41b5-a48e-8f3c5877c18f
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
GTS PDFX Version                : PDF/X-1:2001
GTS PDFX Conformance            : PDF/X-1a:2001
Create Date                     : 2012:10:13 05:43:47+08:00
Metadata Date                   : 2012:11:07 12:30:52-06:00
Modify Date                     : 2012:11:07 12:30:52-06:00
Creator Tool                    : Adobe InDesign CS5 (7.0.4)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 11122 bytes, use -b option to extract), (Binary data 9795 bytes, use -b option to extract)
Instance ID                     : uuid:724b5d7a-79c3-4a21-9950-ae646191fa84
Document ID                     : xmp.did:BA45A026603DE111AD9DA3673049D084
Original Document ID            : xmp.did:C92910718426E111ABD9E0F744E301A4
Rendition Class                 : proof:pdf
Version ID                      : 1
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:C92910718426E111ABD9E0F744E301A4, xmp.iid:1D8393998C26E111ABD9E0F744E301A4, xmp.iid:1E8393998C26E111ABD9E0F744E301A4, xmp.iid:A5C7E08C8D26E111ABD9E0F744E301A4, xmp.iid:F49E02AD9026E111ABD9E0F744E301A4, xmp.iid:DDC31B249126E111ABD9E0F744E301A4, xmp.iid:4841ACFD9B26E111ABD9E0F744E301A4, xmp.iid:D34756322827E111AFF2BAABEBD45EC8, xmp.iid:4C3781842A27E111B893C222155AB82A, xmp.iid:AF48FB272B27E111B893C222155AB82A, xmp.iid:38D1A21D2E27E111B893C222155AB82A, xmp.iid:8BA460163127E111B893C222155AB82A, xmp.iid:1963D1113327E111B893C222155AB82A, xmp.iid:723A44B93327E111B893C222155AB82A, xmp.iid:70F775FA3327E111B893C222155AB82A, xmp.iid:C0BAC3173427E111B893C222155AB82A, xmp.iid:B93FE2ABAC38E111B6BE8FDFB0F8A241, xmp.iid:9AFCB863AF38E111B6BE8FDFB0F8A241, xmp.iid:994583DCAF38E111B6BE8FDFB0F8A241, xmp.iid:1391EF54B138E111B6BE8FDFB0F8A241, xmp.iid:BC45D708B238E111B6BE8FDFB0F8A241, xmp.iid:B0F8837FFE3AE111A718E541BFC7451D, xmp.iid:1B6A6EC2043BE111A718E541BFC7451D, xmp.iid:2559AF1D053BE111A718E541BFC7451D, xmp.iid:13A33447093BE111A718E541BFC7451D, xmp.iid:A53304050A3BE111A718E541BFC7451D, xmp.iid:E6F875690B3BE111A718E541BFC7451D, xmp.iid:1CAFC3B60B3BE111A718E541BFC7451D, xmp.iid:09E9B7F50B3BE111A718E541BFC7451D, xmp.iid:0AE9B7F50B3BE111A718E541BFC7451D, xmp.iid:A370EF530D3BE111A718E541BFC7451D, xmp.iid:AB3A183C803CE11181FBD898F2B4AA3A, xmp.iid:B7344DF1803CE11181FBD898F2B4AA3A, xmp.iid:4A5BA866813CE11181FBD898F2B4AA3A, xmp.iid:49C63292813CE11181FBD898F2B4AA3A, xmp.iid:72546631873CE11181FBD898F2B4AA3A, xmp.iid:5E7A8C165F3DE111AD9DA3673049D084, xmp.iid:56DB627F5F3DE111AD9DA3673049D084, xmp.iid:1DC94BFC5F3DE111AD9DA3673049D084, xmp.iid:1EC94BFC5F3DE111AD9DA3673049D084, xmp.iid:BA45A026603DE111AD9DA3673049D084, xmp.iid:A692DCF7603DE111AD9DA3673049D084, xmp.iid:DD1C6F28613DE111AD9DA3673049D084, xmp.iid:E96B5547613DE111AD9DA3673049D084, xmp.iid:75A9828D613DE111AD9DA3673049D084, xmp.iid:E3F9E5704B77E1119800D9E4EC12DB2F, xmp.iid:4BEFB9C74B77E1119800D9E4EC12DB2F, xmp.iid:9A76702D4C77E1119800D9E4EC12DB2F, xmp.iid:827224D84E77E1119800D9E4EC12DB2F, xmp.iid:ED23C2BA5477E1119800D9E4EC12DB2F, xmp.iid:698CB1327F77E11192EDE0A8F19BD424, xmp.iid:FFCD1DEA8077E11193E3EAB4C88566AC, xmp.iid:AD7E9C5AB490E111AF9BF85CDE10B5F2, xmp.iid:70147EF4EE13E21192F1AC68851267E9, xmp.iid:4BE761E98514E211A97898A588A3A322, xmp.iid:FFB0F9B18614E211A97898A588A3A322, xmp.iid:B8DB5BEDA114E211A97898A588A3A322, xmp.iid:D4A0AB38A214E211A97898A588A3A322, xmp.iid:314385B8A914E211A97898A588A3A322, xmp.iid:908DA3FDA914E211A97898A588A3A322, xmp.iid:9501363EB414E211A97898A588A3A322, xmp.iid:A6F032D0B414E211A97898A588A3A322, xmp.iid:62A99D24B514E211A97898A588A3A322
History When                    : 2011:12:15 03:33:29+08:00, 2011:12:15 03:48:31+08:00, 2011:12:15 03:48:31+08:00, 2011:12:15 03:55:19+08:00, 2011:12:15 04:17:41+08:00, 2011:12:15 04:21:01+08:00, 2011:12:15 05:38:41+08:00, 2011:12:15 22:22:19+08:00, 2011:12:15 22:38:56+08:00, 2011:12:15 22:43:30+08:00, 2011:12:15 23:04:41+08:00, 2011:12:15 23:25:58+08:00, 2011:12:15 23:40:09+08:00, 2011:12:15 23:44:50+08:00, 2011:12:15 23:46:39+08:00, 2011:12:15 23:47:28+08:00, 2012:01:07 05:23:26+08:00, 2012:01:07 05:42:54+08:00, 2012:01:07 05:46:16+08:00, 2012:01:07 05:56:48+08:00, 2012:01:07 06:01:50+08:00, 2012:01:10 04:14:13+08:00, 2012:01:10 04:59:02+08:00, 2012:01:10 05:01:35+08:00, 2012:01:10 05:31:23+08:00, 2012:01:10 05:36:41+08:00, 2012:01:10 05:46:39+08:00, 2012:01:10 05:48:49+08:00, 2012:01:10 05:50:35+08:00, 2012:01:10 05:52:12+08:00, 2012:01:10 06:00:22+08:00, 2012:01:12 02:15:25+08:00, 2012:01:12 02:20:30+08:00, 2012:01:12 02:23:46+08:00, 2012:01:12 02:25+08:00, 2012:01:12 03:05:14+08:00, 2012:01:13 04:50:40+08:00, 2012:01:13 04:53:36+08:00, 2012:01:13 04:57:06+08:00, 2012:01:13 04:58:16+08:00, 2012:01:13 04:58:17+08:00, 2012:01:13 05:04:08+08:00, 2012:01:13 05:05:29+08:00, 2012:01:13 05:06:21+08:00, 2012:01:13 05:08:19+08:00, 2012:03:26 21:56:09+08:00, 2012:03:26 21:58:35+08:00, 2012:03:26 22:01:26+08:00, 2012:03:26 22:20:31+08:00, 2012:03:26 23:02:39+08:00, 2012:03:27 04:06:39+08:00, 2012:03:27 04:18:56+08:00, 2012:04:28 06:00:08+08:00, 2012:10:12 05:59:40+08:00, 2012:10:13 00:00:15+08:00, 2012:10:13 00:05:52+08:00, 2012:10:13 03:20:47+08:00, 2012:10:13 03:22:54+08:00, 2012:10:13 04:16:35+08:00, 2012:10:13 04:18:31+08:00, 2012:10:13 05:31:54+08:00, 2012:10:13 05:35:59+08:00, 2012:10:13 05:38:21+08:00
History Software Agent          : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata, /;/metadata
Derived From Instance ID        : xmp.iid:1EC94BFC5F3DE111AD9DA3673049D084
Derived From Document ID        : xmp.did:C92910718426E111ABD9E0F744E301A4
Derived From Original Document ID: xmp.did:C92910718426E111ABD9E0F744E301A4
Derived From Rendition Class    : default
Doc Change Count                : 2651
Format                          : application/pdf
Title                           : 1F97-1277_37-7388A.indd
Creator                         : Adobe InDesign CS5 (7.0.4)

EXIF Metadata provided by EXIF.tools

Emerson 1F97 1277 Users Manual 1277_37 7388A

White-Rodgers-1F97-1277-Emerson-Blue-12-Touchscreen-Single-Stage-Thermostat-Installation-And-Operation-Instructions-677013 white-rodgers-1f97-1277-emerson-blue-12-touchscreen-single-stage-thermostat-installation-and-operation-instructions-677013

1f971277 1555708d-85de-4161-a3cd-72ad98593f4c Emerson Thermostat 1F97-1277 User Guide |

Navigation menu

Versions of this User Manual:

Views

Navigation