Emerson 66R Series Vapor Recovery Valves Instruction Manual
2015-03-30
: Emerson Emerson-66R-Series-Vapor-Recovery-Valves-Instruction-Manual-680980 emerson-66r-series-vapor-recovery-valves-instruction-manual-680980 emerson pdf
Open the PDF directly: View PDF 
.
Page Count: 12
Types 66R and 66RR
D100248X012
Instruction Manual
Form 1737
November 2009
TYPE 66R RELIEF VALVE
W1935
TYPE 66RR RELIEF VALVE
W1908
Figure 1. Typical Constructions
*Relief valve dened in ANSI standard B95.1-1972. Not all codes or regulations permit these valves to be used as nal overpressure protection devices.
This manual describes and provides instructions, installation,
and parts list for Type 66R direct-operated relief valve* and
for Type 66RR pilot-operated relief valve* complete with
Type Y695RR pilot. Instructions and parts list for other
Fisher® equipment used with these relief valves are found in
separate manuals.
Types 66R and 66RR throttling relief valves (Figure 1) are
used to help protect a system against overpressure, or to
maintain an inlet or backpressure. The Type 66R direct-
operated construction is used for set pressure ranges of
2-inches w.c. to 5 psig (5 mbar to 0,34 bar), while the
Type 66RR pilot-operated construction with the Type Y695RR
pilot is used for set pressure ranges of 4-inches w.c. to 7 psig
(10 mbar to 0,48 bar).
Refer to Specications for Types 66R and 66RR
constructions listed on page 2. Some specications for a
given relief valve as it originally comes from the factory are
stamped on nameplates located on the Type 66R relief valve
body or Type 66RR main valve body.
Refer to Figure 2. Inlet pressure registers under the diaphragm
and is opposed by the spring. When the inlet pressure
increases above the spring setting, the valve plug opens in
a throttling manner and relieves the inlet pressure. As inlet
pressure drops back to set pressure, the spring closes the
valve plug.
Refer to Figure 2. Inlet pressure registers on the bottom
of the pilot diaphragm through the upstream control line
and bleeds through a xed restriction in the pilot to provide
loading pressure that helps the main valve spring keep
the main valve plug tightly shut off. When inlet pressure
exceeds the setting of the pilot spring, the pilot diaphragm
moves upward, opening the pilot valve disk and relieving
Types 66R and 66RR
2
2 (50) NPT or CL125 FF
anged
NPT, CL150 RF, and
CL300 RF anged
3, 4
(80, 100) CL125 FF anged CL150 RF anged
8 psig (0,55 bar), including build-up
10 psig (0,69 bar), including build-up
2-inches w.c. to 5 psig
(5 mbar to 0,34 bar) in 7 ranges
4-inches w.c. to 7 psig
(10 mbar to 0,48 bar) See Table 1
8 psig (0,55 bar)
10 psig (0,69 bar)
2-inch (51 mm)
3-inch (76 mm)
4-inch (102 mm)
-20° to 180°F (-29° to 82°C)
0° to 350°F (-18° to 177°C)
Adjusting screw
Internal or external
External on pilot and internal in main valve
Control Line (If Used): 3/4 NPT internal
Spring Case Vent: 3/4 NPT internal with removable
Type Y602-10 vent assembly
Pilot Body: 3/4 NPT internal
Pilot Diaphragm Case: 1/2 NPT internal
Pilot Spring Case: 1/4 NPT internal
NPT: 50 pounds (23 kg) for Type 66R or
65 pounds (30 kg) for Type 66RR
Flanged: 55 pounds (25 kg) for Type 66R or
70 pounds (32 kg) for Type 66RR
100 pounds (45 kg) for
Type 66R or 115 pounds (52 kg) for Type 66RR
155 pounds (70 kg) for
Type 66R or 170 pounds (77 kg) for Type 66RR
1. The pressure/temperature limits in this Instruction Manual and any applicable standard or code limitation should not be exceeded.
some of the pressure from the top of the main valve
diaphragm. At the same time, the inlet pressure increase
registers on the bottom of the main valve diaphragm.
The pressure differential acting on the main valve diaphragm
moves this diaphragm upward, opening the main valve.
Further increases in inlet pressure continue to open the pilot
valve disk and the main valve plug. When inlet pressure
returns to the pilot control spring setting, the pilot disk
closes, allowing inlet pressure to load the top of the main
valve diaphragm through the xed restriction. This equalizes
the pressures acting on this diaphragm, and the main valve
spring closes the main valve plug.
Standard
4 to 9-inches w.c. (10 to 22 mbar)(1)
5 to 15-inches w.c. (12 to 37 mbar)(1)
12 to 28-inches w.c. (30 to 70 mbar)(1)
0.9 to 2.5 psig (0,06 to 0,17 bar)
1.3 to 4.5 psig (0,09 to 0,31 bar)
1B653827052
1B653927022
1B537027052
1B537127022
1B537227022
Red
Olive drab
Yellow
Light green
Light blue
0.085 (2,16)
0.105 (2,67)
0.114 (2,90)
0.156 (3,96)
0.187 (4,75)
3.625 (92,1)
3.750 (95,3)
4.188 (106)
4.060 (103)
3.938 (100)
Special 3.8 to 7 psig (0,26 to 0,48 bar) 1B537327052 Black 0.218 (5,54) 3.980 (101)
1. Published ranges are with the spring case pointed up.
Table 1. Type Y695RR Pilot Control Spring Selection
!
Types 66R and 66RR
3
1. Use qualied personnel when installing, operating, and
maintaining these relief valves. Before installing,
inspect the relief valve, and pilot if used, for any damage
or foreign material that may have collected.
2. Make certain the body interior is clean and that
pipelines are free of foreign material. Apply pipe
compound to only the male pipeline threads with an
NPT body, or use suitable line gaskets and acceptable
bolting practices with a anged body.
3. Install a Type 66R or 66RR relief valve in a horizontal
pipeline with the diaphragm casings above the body.
Other orientations will change the relief set pressure and
set pressure range due to the weight of the internal
parts. The ow through the relief valve must comply
with the ow arrow on the body.
4. An upstream control line is not required for a standard
Type 66R relief valve with internal registration through
a stem guide (key 41, Figure 6). However, for an
optional Type 66R relief valve with sealing diaphragm
(key 14, Figure 6), connect a control line to the 3/4-inch
NPT tapped connection boss on the diaphragm case
(key 3, Figure 6) as shown in Figure 3.
5. For a Type 66RR relief valve used in a relief application,
connect an upstream control line to the 1/2 NPT
connection on the pilot diaphragm case (key 4, Figure 8).
For other typical applications, piping arrangements
are shown in Figures 4 and 5. Regardless of Type 66RR
installation, the pipe plug (key 78, not shown) will have
to be removed from the vent of the Type Y695RR pilot
spring case (key 3, Figure 8).
6. On backpressure or bypass applications, install a
three-valve isolating bypass, and vent valves
immediately upstream and downstream of the unit, if
system operation is necessary during maintenance.
7. The standard Type 66R spring case (key 2, Figure 6) has
a Type Y602-10 vent assembly (key 30, Figure 6) installed
in the 3/4 NPT spring case tapping. The vent may be
removed and obstruction-free piping or tubing installed for
remote piping of the spring case or for pressure loading of
the spring case as shown in Figure 5. If kept in the spring
case, the vent must be protected against clogging.
M1041 M1056
!
Figure 2. Operational Schematics
TYPE 66R TYPE 66RR
skIRT
skIRT
Types 66R and 66RR
4
8. Each unit is factory-set for the set pressure specied on
the order. If no setting is specied, set pressure is factory
set at the mid-range of the Type 66R spring (key 6,
Figure 6) or the Type 66RR pilot control spring (key 6,
Figure 8). The set pressure of a unit is adjusted by
changing the compression of the appropriate spring.
Check and verify the spring setting to make sure that it is
correct for the application.
9. Set pressure for a Type 66RR relief valve is dened as
the pressure at which the main valve starts-to-
discharge. Type 66RR units have been designed so
that either a 1-inch w.c. (2,50 mbar) build-up or a
5 percent build-up (whichever is greater) above this set
pressure will open the main valve and permit it to yield
full open capacity.
Key numbers are referenced in Figure 6 for the Type 66R
relief valve, in Figure 7 for the Type 66RR main valve, and in
Figure 8 for the Type 66RR relief valve pilot.
With proper installation and adjustment completed, slowly
open the upstream shutoff valve while using gauges to
monitor pressure. To monitor inlet pressure, remove the pipe
plug (key 31, not shown) on the side of the body opposite
the ow arrow, and then temporarily install a gauge.
On backpressure or bypass applications using an isolating
bypass, also open the downstream shutoff valve and close
the bypass valve.
If set pressure adjustment is necessary, monitor inlet
pressure with a gauge during the adjustment procedure.
Adjust a Type 66R relief valve by removing the closing
cap (key 27) if necessary, loosening the locknut (key 45) if
used, and turning the adjusting screw (key 25) clockwise to
increase or counterclockwise to decrease the set pressure.
After adjustment, tighten the locknut or install the closing
cap. To adjust a Type 66RR relief, remove the Type Y695RR
pilot closing cap (key 22), turn the adjusting screw (key 35)
clockwise to increase or counterclockwise to decrease the
set pressure, and then install the closing cap.
Slowly close the upstream shutoff valve. Release all
pressure from the relief valve, and pilot if used, by opening
the upstream vent valve.
Slowly close the upstream shutoff valve, while opening the
bypass valve if an isolating bypass is used. Then, close the
downstream shutoff valve, and open both vent valves to
release all pressure from the relief valve (and pilot if used).
TAnk
BJ8921-C
A2562
AV9712-D
A2564
AV9712-D
A2563-1
Figure 3. Type 66R Relief Valve Installation at Outlet
of Sewage Treatment Plant Digester Tank
Figure 4. Type 66RR Relief Valve Installation in
Vacuum Breaker System
Figure 5. Type 66R Relief Valve Installation in
Vacuum Regulation System
Types 66R and 66RR
5
!
Relief valve parts are subject to normal wear and must
be inspected and replaced as necessary. The frequency
of inspection and replacement of parts depends upon the
severity of service conditions and the requirements of local,
state, and federal regulations.
This section gives procedures for complete disassembly
and assembly of the relief valve or main valve body.
Disassemble the valve only as far as required to gain
access to the necessary parts. Then, begin the “Assembly”
procedure at the appropriate step. Key numbers for the
Type 66R relief valve are referenced in Figure 6 and, for the
Type 66RR main valve, in Figure 7.
Disassembly
1. With a Type 66RR relief valve, disconnect the pilot
control and/or vent lines.
2. Loosen the locknut (key 45) if used, and remove the
closing cap (key 27) and closing cap gasket (key 26).
3. In order to facilitate resetting spring compression during
assembly, be sure to note the position of the adjusting
screw (key 25) before removing it. Then, turn the
screw out of the spring case (key 2) to remove spring
compression, and remove the upper spring seat
(key 24), spring (key 6), cap screws and nuts (keys 21
and 22), and spring case.
4. Unscrew the stem nut (key 23) from the top of the stem
(key 13). To keep the stem from twisting, lift the
diaphragm (key 5) and attached parts far enough to hold
the stem with an open-end wrench. Or, remove the
pipe plug (key 31, not shown) from the side of the
body opposite the arrow, and insert a 5/16-inch
(7,94 mm) or smaller rod through the pipe plug hole
and the hole in the stem.
5. Remove the spring seat washer (key 36) if used,
lower spring seat (key 17), stiffener plate (key 39) if
used, upper diaphragm plate (key 4), diaphragm
(key 5), lower diaphragm plate (key 15), stem gasket
(key 18), diaphragm spacer (key 16) if used, and another
stem gasket and lower diaphragm plate if used. With a
high-temperature uorocarbon (FKM) diaphragm, remove
the diaphragm gasket (key 66, not shown) that goes
between the diaphragm and diaphragm case (key 3).
6. Remove the cap screws (key 20) and washers (key 34)
that attach the diaphragm case to the body (key 1).
7. Remove the diaphragm case and diaphragm case
gasket (key 35). Depending on construction, remove
either the stem guide (key 41) or the sealing diaphragm
(key 14) and last lower diaphragm plate (key 15) and
stem gasket (key 18). If used, remove the rod from the
stem and the pipe plug hole in the body.
8. Lift out the stem and attached parts.
9. Unscrew the stem nut (key 23) from the bottom of the
stem, and remove the valve plug skirt (key 10), O-ring
(key 8), O-ring retainer (key 9), and seal washer (key 37).
10. Slide a seat ring puller, T-wrench, or other suitable tool
over the seat ring (key 11). Engage the tool with the
seat ring lugs. Unscrew the seat ring.
11. If necessary to replace the bottom ange gasket
(key 19), remove the cap screws (key 20), bottom
ange (key 7), and gasket.
Assembly
1. Apply pipe compound to the threads of the seat ring
(key 11). Screw in the seat ring, using a seat ring puller
or similar device. Wipe off any excess pipe compound.
2. Place the seal washer (key 37), O-ring retainer (key 9),
O-ring (key 8), and valve plug skirt (key 10) on the stem
(key 13) in the order shown in Figure 6 or 7.
3. Secure the stem nut (key 23) to the stem. Install the
stem and attached parts into the body.
4. If necessary, install a new bottom ange gasket (key 19)
and the bottom ange (key 7) on the valve body. Secure
the ange with the cap screws (key 20).
5. Depending on construction, either install the stem guide
(key 41) on the body, or install the stem gasket (key 18),
lower diaphragm plate (key 15), and the sealing
diaphragm (key 14) on the stem. Make sure that on a
sealing diaphragm, the diaphragm holes are aligned
with the body ange holes.
Types 66R and 66RR
6
!
6. Install the diaphragm case gasket (key 35) and
diaphragm case (key 3) on either the body ange or
sealing diaphragm, making sure the gasket and case
holes are aligned with the body ange holes.
7. Secure the diaphragm case with the washers (key 34)
and cap screws (key 20), tightening the cap screws
with an even crisscross pattern. With a high-temperature
uorocarbon (FKM) diaphragm, use a new case
gasket (key 66, not shown), and install it on top of the
diaphragm case.
8. With a sealing diaphragm construction, place another
lower diaphragm plate on the sealing diaphragm so that
the cupped side of the plate faces up, followed by
another stem gasket (key 18) and the diaphragm spacer
(key 16) if used.
9. Place a stem gasket (key 18) on the stem or diaphragm
spacer, followed by the lower diaphragm plate (key 15),
diaphragm (key 5), upper diaphragm plate (key 4),
stiffener plate (key 39) if used, lower spring seat
(key 17), and spring seat washer (key 36) if used.
10. To keep the stem (key 13) from rotating, insert a
5/16-inch (7,9 mm) or smaller rod into the pipe plug
hole and through the hole in the stem, or reach far
enough under the diaphragm with an open-end wrench
to hold the stem. Install the other stem nut (key 23) on
the stem.
11. Remove the rod (if used) from the pipe plug hole, and
install the pipe plug (key 31, not shown) in the body.
12. Install the spring case (key 2) on the diaphragm, and
secure with the cap screws and nuts (keys 21 and 22),
nger-tightening only at this point.
13. Install the spring (key 6), upper spring seat (key 24),
adjusting screw (key 25), and new closing cap gasket
(key 26). With some constructions, the closing cap
(key 27) will have to be installed before the
adjusting screw.
14. Compress the spring slightly with the adjusting screw to
ensure proper slack in the diaphragm. Tighten the nuts
and cap screws alternately in equal increments to
avoid crushing the diaphragm.
15. Turn a Type 66RR adjusting screw into the spring case
to the position noted in “Disassembly” step 3. If this
position was not marked, turn the adjusting screw until
the valve begins to open when inlet pressure just
exceeds 2-inches w.c. (5 mbar).
16. Complete the relief valve adjustment according to the
“Startup” section.
Body Area
This procedure is for gaining access to the disk assembly,
orice, and body seal O-ring. All pressure must be released
from the regulator, before the following steps can be
performed. Key numbers are referenced in Figure 8.
1. To inspect and replace the disk assembly (key 13)
remove the body cap assembly (key 43).
2. Remove the disk assembly (key 13) from the disk spacer
(key 44) and replace if necessary.
3. To inspect the orice (key 5), remove the cap screws
(key 2) and separate the diaphragm case assembly
(key 4) from the body (key 1).
4. Remove and inspect the body seal O-ring (key 11) and
the backup ring (key 49). Replace if damaged.
5. Inspect and replace the orice (key 5) if necessary.
Lightly lubricate the threads of the replacement orice.
Install with 29 to 37 foot pounds (39 to 50 N•m)
of torque.
6. Install the backup ring (key 49) into the body
(key 1). Next place the body seal O-ring (key 11) into
the body. See Figure 8.
7. Replace the diaphragm casing (key 4) on the body
(key 1) and secure with the cap screws (key 2) using 7
to 9 foot pounds (9,50 to 12 N•m) of torque.
8. Secure the disk assembly (key 13) to the disk spacer
(key 44). Place the back disk spring (key 41) and a new
back body seal O-ring (key 42) on the back body cap
(key 43).
9. Lightly lubricate the threads when replacing the body
cap assembly.
Diaphragm and Spring Case Area
This procedure is for gaining access to the control spring,
diaphragm, and lever assembly stem. All pressure must
be released from the diaphragm case assembly before
performing the following steps. Key numbers are referenced
in Figure 8.
Types 66R and 66RR
7
1. Remove the closing cap (key 22), and turn the adjusting
screw (key 35) counterclockwise to remove all
compression from the control spring (key 6).
2. Remove the adjusting screw (key 35) and change the
control spring to match the desired spring range.
3. Install the adjusting screw (key 35) and refer to the
Startup section for adjustment.
4. Install a replacement closing cap gasket (key 25), if
necessary, and reinstall the closing cap (key 22).
5. If the spring range was changed, be sure to change the
stamped spring range on the spring case nameplate.
1. Remove the closing cap (key 22) and the adjusting
screw (key 35).
2. Remove the hex nuts (key 23, not shown) and cap
screws (key 24), lift off the spring case assembly
(key 3) and remove the control spring (key 6).
3. Remove the diaphragm (key 10) plus attached parts by
tilting them so that the pusher post (key 8) slips off
the lever assembly (key 16). To separate the diaphragm
assembly (key 10) from the attached parts, unscrew the
diaphragm plate cap screw (key 38) from the pusher
post (key 8). If the only further maintenance is to
replace the diaphragm parts, skip to step 7.
4. To replace the lever assembly (key 16), remove the
machine screws (key 17). To replace the stem
(key 14), perform Body Area Maintenance procedure
step 3, and pull the stem (key 14) out of the guide insert
(key 18).
5. Install the stem (key 14) into the guide insert (key 18)
and perform Body Area Maintenance procedure steps 6
and 7 as necessary.
6. Install the lever assembly (key 16) into the stem (key 14)
and secure the lever assembly (key 16) with the machine
screws (key 17).
7. Reassemble the diaphragm parts as follows:
• Pusher post (key 8)
• Diaphragm head gasket (key 45)
• Diaphragm head (key 7)
• Diaphragm (key 10)
• Diaphragm head (key 7)
• Lower spring seat (key 50)
• Washer (key 36)
• Diaphragm plate cap screws (key 38)
Secure using 5 to 6 foot-pounds (7 to 8 N•m) of torque.
8. Install the pusher post (key 8) plus attached diaphragm
parts onto the lever assembly (key 16).
9. Install the spring case (key 3) on the diaphragm casing
(key 4) so that the vent assembly (key 26) is correctly
oriented, and secure it with the cap screws (key 24) and
hex nuts (key 23, not shown) ngertight.
10. Install the control spring (key 6) and the adjusting
screw (key 35) in the spring case (key 3). Turn the
adjusting screw (key 35) clockwise until there is
enough control spring (key 6) force to provide proper
slack to the diaphragm (key 10). Using a crisscross
pattern, nish tightening the cap screws (key 24) and
hex nuts (key 23, not shown) to 160 to 190 inch-
pounds (18 to 21 N•m) of torque. To adjust the outlet
pressure to the desired setting, refer to the Startup
and Adjustment section.
11. Install a replacement closing cap gasket (key 25) if
necessary, and then install the closing cap (key 22).
A Type 66R or 66RR relief valve has a serial number
stamped on a nameplate attached to the diaphragm case.
When corresponding with your local Sales Ofce, always
refer to this serial number. Also, when ordering replacement
parts, give the complete 11-character part number of each
needed part as found in the following parts list.
1 Body
Cast iron (not for use with sealing
diaphragm)
2 NPT 2K556819012
CL125 FF anged
NPS 2 (DN 50) 2K557019012
NPS 3 (DN 80) 2K557219012
NPS 4 (DN 100) 2K557419012
Cast iron for use with sealing
diaphragm (Type 66R only)
2 NPT 2K556719012
CL125 FF anged
NPS 2 (DN 50) 2K5569X0012
NPS 3 (DN 80) 2K557119012
NPS 4 (DN 100) 2K557319012
WCC Steel (not for use with sealing
diaphragm)
2 NPT 2L3505X0012
CL150 RF anged
NPS 2 (DN 50) 2J840122012
NPS 3 (DN 80) 2P936022012
NPS 4 (DN 100) 2N850022012
NPS 2 (DN 50) CL300 RF anged 2L4426X0012
2 Spring Case, Steel (complete with SST
drive screw) See following table
Types 66R and 66RR
8
20
7
19
1
10
11
8
9
13
41
34
15
3
22
32
21
5332439
17
36
40
6
24
25
26
27
23
29
28
30
18
35
37
23
Figure 6. Type 66R Relief Valve
*Recommended spare part.
40A6361-B
30A6359-B
B1433
3 Diaphragm Case, Steel
Standard
NPS 2 (DN 50) body 3D478728992
NPS 3 (DN 80) body 3D478928992
NPS 4 (DN 100) body 3D479128992
Optional 3/4 NPT tapped
(for Type 66R with sealing diaphragm only)
NPS 2 (DN 50) body 1F4421000A2
NPS 3 (DN 80) body 1F4419000A2
NPS 4 (DN 100) body 1F1319000A2
4 Upper Diaphragm Plate, Zinc-plated steel
NPS 2 (DN 50) body
2-inches w.c. to 2 psig (5 mbar to 0,14 bar)
set pressures for Type 66R or 3-inches w.c.
to 3.25 psig (7 mbar to 0,22 bar) set
pressures for Type 66RR 1D255625072
1.5 to 5 psig (0,10 to 0,34 bar)
set pressures for Type 66R or 3.25 to
7 psig (0,22 to 0,48 bar) set
pressures for Type 66RR 1D555725012
NPS 3 (DN 80) body 1D477328992
NPS 4 (DN 100) body 1D477425062
5* Diaphragm
Nitrile (NBR)
NPS 2 (DN 50) body 1D477002072
NPS 3 (DN 80) body 1D477102072
NPS 4 (DN 100) body 1D477202072
Fluorocarbon (FKM)
NPS 2 (DN 50) body 1D477002332
NPS 3 (DN 80) body 1D477102332
NPS 4 (DN 100) body 1D477202332
6 Spring, Zinc-plated steel See following table
7 Bottom Flange, Steel
NPS 2 (DN 50) body 1D477825062
NPS 3 (DN 80) body 17A9250X012
NPS 4 (DN 100) body 1D478025062
8* O-Ring
Nitrile (NBR)
NPS 2 (DN 50) body 1D785306992
NPS 3 (DN 80) body 1D785406992
NPS 4 (DN 100) body 1D785506992
Fluorocarbon (FKM)
NPS 2 (DN 50) body 1N115606382
NPS 3 (DN 80) body 1N115706382
NPS 4 (DN 100) body 1D2658X0022
9 O-Ring Retainer
Brass
NPS 2 (DN 50) body 1D475814012
NPS 3 (DN 80) body 1D475914012
NPS 4 (DN 100) body 1D476014012
316 SST
NPS 2 (DN 50) body 1D475835072
NPS 3 (DN 80) body 1D475935072
NPS 4 (DN 100) body 1D476035072
10 Valve Plug Skirt
Brass
NPS 2 (DN 50) body 1D476112012
NPS 3 (DN 80) body 1D476212012
NPS 4 (DN 100) body 1D476312012
316 SST
NPS 2 (DN 50) body 1D476133092
NPS 3 (DN 80) body 1D476233092
NPS 4 (DN 100) body 1D476333092
18
15
13
14
16
35
27
25
45
26
24
Types 66R and 66RR
9
51A7562_E
Figure 7. Type 66RR Main Valve and Pilot Mounting Parts
*Recommended spare part.
11 Seat Ring
Bronze
NPS 2 (DN 50) body 1D783012022
NPS 3 (DN 80) body 1D783112022
NPS 4 (DN 100) body 1D783212022
316 SST
NPS 2 (DN 50) body 1D783033092
NPS 3 (DN 80) body 1D783133092
NPS 4 (DN 100) body 1D783233092
13 Valve Stem
For use without sealing diaphragm
Brass
NPS 2 (DN 50) body 1D752914012
NPS 3 (DN 80) body
Cast iron body 1D754514012
Steel body 1N4455X0012
NPS 4 (DN 100) body 1D759614012
316 SST
NPS 2 (DN 50) body 1D752935072
NPS 3 (DN 80) body
Cast iron body 1D754535072
Steel body 1N445535072
NPS 4 (DN 100) body 1D759635072
For use with sealing diaphragm
Brass
NPS 2 (DN 50) body 1J820214012
NPS 3 (DN 80) body 1J259114012
NPS 4 (DN 100) body 1J130814012
For use with sealing diaphragm
316 SST
NPS 2 (DN 50) body 1J820235072
NPS 3 (DN 80) body 1J259135072
NPS 4 (DN 100) body 1J130835072
14* Sealing Diaphragm (for Type 66R
with tapped diaphragm case only)
Nitrile (NBR)
NPS 2 (DN 50) body 1H737002042
NPS 3 (DN 80) body 1J198102042
NPS 4 (DN 100) body 1H727502042
Fluorocarbon (FKM)
NPS 2 (DN 50) body 1H7370X0012
NPS 3 (DN 80) body 1J1981X0012
NPS 4 (DN 100) body 1H7275X0012
15 Lower Diaphragm Plate, Zinc-plated steel
(1 required without and 3 required with
sealing diaphragm)
NPS 2 (DN 50) body 1D475725062
NPS 3 (DN 80) body 1D479325062
NPS 4 (DN 100) body 1D479425062
16 Diaphragm Spacer (for Type 66R
with sealing diaphragm only),
Zinc-plated steel
NPS 2 (DN 50) body 1J820326092
NPS 3 (DN 80) body 1J259226092
NPS 4 (DN 100) body 1J130926092
17 Lower Spring Seat
Type 66R thru 3 psig (0,21 bar) set
pressures and all Type 66RR,
Aluminum 0X014744012
Type 66R for 3 to 5 psig
(0,21 to 0,34 bar) set pressures,
Brass 1J331314012
18* Stem Gasket, Composition (1 required without
and 3 required with sealing diaphragm)
NPS 2 or 3 (DN 50 or 80) body 1D255304022
NPS 4 (DN 100) body 1D478404022
Types 66R and 66RR
10
Key 2, Spring Case Assembly
Key 6, Spring
2 (50)
Type 66R 2 to 8-inches w.c. (5 to 20 mbar) 1D7614X0012 1D765427012
Type 66RR 3 to 8-inches w.c. (7 to 20 mbar) 12A6056X012
Type 66R only
6 to 16-inches w.c. (15 to 40 mbar)
11-inches w.c. to 1 psig (27 mbar to 0,07 bar)
0.75 to 1.5 psig (0,05 to 0,10 bar)
1 to 2 psig (0,07 to 0,14 bar)
1.5 to 3 psig (0,10 to 0,21 bar)
3 to 5 psig (0,21 to 0,34 bar)
1D7614X0022
1D7614X0032
1D7614X0042
1D7614X0052
1D7614X0062
1D4792000A2
1D765527012
1D765627032
1D765727032
1D765827032
1D962627032
1N506427142
3 (80)
Type 66R 2 to 8-inches w.c. (5 to 20 bar) 1D7614X0072 1D770727012
Type 66RR 3 to 8-inches w.c. (7 to 20 mbar) 12A6057X012
Type 66R only
6 to 16-inches w.c. (15 to 40 mbar)
11-inches w.c. to 1 psig (27 mbar to 0,07 bar)
0.75 to 1.5 psig (0,05 to 0,10 bar)
1 to 2 psig (0,07 to 0,14 bar)
1.5 to 3 psig (0,10 to 0,21 bar)
3 to 5 psig (0,21 to 0,34 bar)
1D7614X0082
1D7614X0092
1D7614X0102
1D7614X0112
1D7614X0122
1D5391000A2
1D770827032
1D765727032
1D765827032
1D770927032
1E204427032
1N506527142
4 (100)
Type 66R 2 to 8-inches w.c. (5 to 20 mbar) 1D7614X0132 1D771027012
Type 66RR 3 to 8-inches w.c. (7 to 20 mbar) 12A6058X012
Type 66R only
6 to 16-inches w.c. (15 to 40 mbar)
11-inches w.c. to 1 psig (27 mbar to 0,07 bar)
0.75 to 1.5 psig (0,05 to 0,10 bar)
1 to 2 psig (0,07 to 0,14 bar)
1.5 to 3 psig (0,10 to 0,21 bar)
1D7614X0142
1D7614X0152
1D7614X0162
1D7614X0172
1D7614X0182
1D771127032
1D527627032
1D771227032
1D771327032
1E204527032
*Recommended spare part.
Monel® is a mark owned by Special Metals Corporation
19* Bottom Flange Gasket, Composition
NPS 2 (DN 50) body 1D476404022
NPS 3 (DN 80) body 1D476504022
NPS 4 (DN 100) body 1D476604022
20 Cap Screw, Zinc-plated steel
NPS 2 (DN 50) body
Cast iron body (13 required) 1C631224052
Steel body (12 required) 1C275224052
NPS 3 (DN 80) body (17 required for
cast iron or 16 for steel body) 1D529824052
NPS 4 (DN 100) body (17 required for
cast iron or 16 for steel body) 1D530824052
21 Cap Screw, Zinc-plated steel
[16 required for NPS 2 (DN 50),
20 for NPS 3 (DN 80), or 24 for
NPS 4 (DN 100) body] 1D529624052
22 Hex Nut, Zinc-plated steel
[16 required for NPS 2 (DN 50),
20 for NPS 3 (DN 80), or 24 for
NPS 4 (DN 100) body] 1A309324122
23 Stem Nut (2 required)
Brass
NPS 2 or 3 (DN 50 or 80) body 1D529718992
NPS 4 (DN 100) body 1D530918992
SST
NPS 2 or 3 (DN 50 or 80) body 1D5297X0022
NPS 4 (DN 100) body 1D5309X0052
24 Upper Spring Seat
Type 66R for 3 to 5 psig (0,21 to
0,34 bar) set pressures, Brass
NPS 2 or 3 (DN 50 or 80) body 1J331214012
NPS 4 (DN 100) body 1E271114012
25 Adjusting Screw
Type 66R thru 2 psig (0,14 bar) set
pressures and all Type 66RR,
Aluminum 1L928608012
Type 66R for 1.5 to 3 psig
(0,10 to 0,21 bar) set pressures,
Brass 1V9069X0012
Type 66R for 3 to 5 psig
(0,21 to 0,34 bar) set pressures
[except NPS 4 (DN 100) body],
Zinc-plated steel
NPS 2 (DN 50) body 1A279128982
NPS 3 (DN 80) body 1N506624102
26* Closing Cap Gasket
Neoprene 1N446206992
27 Closing Cap
Type 66R thru 3 psig (0,21 bar)
set pressures and all Type 66RR,
Die-cast zinc 1A589544022
Type 66R for 3 to 5 psig (0,21 to
0,34 bar) set pressures,
Brass 1H798714012
28 Flapper Valve (for Type 66R only),
Brass 1C901715072
29 Snap Ring (for Type 66R only),
Bronze 1D178016012
30 Type Y602-10 Vent Assembly,
SST/Zinc/Monel® EMY602X1-A10
31 Pipe Plug (not shown)
Cast iron 1A361919012
Steel 1A369224492
Types 66R and 66RR
11
*Recommended spare part.
34 Washer, Zinc-plated steel
NPS 2 (DN 50) body (7 required for
cast iron or 6 for steel body) 1D793624152
NPS 3 (DN 80) body (9 required for
cast iron or 8 for steel body) 1D716228982
NPS 4 (DN 100) body (9 required for
cast iron or 8 for steel body) 1D716328982
35* Diaphragm Case Gasket, Neoprene
Cast iron body
NPS 2 (DN 50) 1D843604082
NPS 3 (DN 80) 1D843704082
NPS 4 (DN 100) 1D843804082
Steel body
NPS 2 (DN 50) 1D753004082
NPS 3 (DN 80) 1D754704082
NPS 4 (DN 100) 1D843804082
36 Spring Seat Washer [for use only with
NPS 2 or 3 (DN 50 or 80) body],
Zinc-plated steel 1H723125072
37 Seal Washer
NPS 2 or 3 (DN 50 or 80) body, Steel 1F990428982
NPS 4 (DN 100) body, Brass 1H720799012
39 Stiffener Plate, Steel
2-inches w.c. to 2 psig (5 mbar to 0,14 bar)
set pressures for Type 66R or 3-inches w.c. to
3.25 psig (7 mbar to 0,22 bar) set
pressures for Type 66RR
NPS 2 or 3 (DN 50 or 80) body 1D753125062
NPS 4 (DN 100) body 1D760725072
1.5 to 5 psig (0,10 to 0,34 bar) set
pressures for Type 66R or 3.25 to 7 psig
(0,22 to 0,48 bar) set pressures for
Type 66RR [not used with NPS 2 (DN 50) body]
NPS 3 (DN 80) body 1E204325012
NPS 4 (DN 100) body 1A355325012
40 Drive Screw, 18-8 SST 1A368228982
41 Stem Guide (not for use with
sealing diaphragm)
Steel
NPS 2 (DN 50) body 1D752824092
NPS 3 (DN 80) body 1D754625032
NPS 4 (DN 100) body 1D759725032
SST
NPS 2 (DN 50) body 1D752835132
NPS 3 (DN 80) body 1D754635132
NPS 4 (DN 100) body 1D759735072
45 Locknut for 3 to 5 psig
(0,21 to 0,34 bar)
set pressure Type 66R only,
Zinc-plated steel 1A352424122
60 U-Bolt (for Type 66RR only),
Steel 11A7488X012
61 U-Bolt (for Type 66RR only), Steel 11A7489X012
62 Mounting Bar (for Type 66RR only), Steel
NPS 2 (DN 50) body 11A7490X012
NPS 3 (DN 80) body 11A8938X012
NPS 4 (DN 100) body 11A8939X012
63 Pipe Union (for Type 66RR only),
Malleable iron 1B540621992
64 Pipe Nipple (for Type 66RR only),
Steel 1K994226012
65 Hex Nut (for Type 66RR only),
Zinc-plated steel (4 required) 1A345724122
66* Diaphragm Gasket (for Fluorocarbon (FKM)
diaphragm only), Fluorocarbon (FKM)
(not shown)
NPS 2 (DN 50) body 1U6985X0012
NPS 3 (DN 80) body 1U6986X0012
NPS 4 (DN 100) body 1U6989X0012
67 Pipe Nipple (for Type 66RR),
Steel 1B539126012
1 Body, Ductile iron 17B9020X012
2 Cap Screw (2 required), Steel 1C856228992
3 Spring Case Assembly, Ductile iron/SST 13B0109X042
4 Diaphragm Casing, Ductile iron 47B3063X012
5 Orice, 316 SST
7/16-inch (11 mm) 0L0832X0012
6 Spring See Table 1
7 Diaphragm Head 304 SST 17B9723X032
8 Pusher Post, 316 SST 18B3465X012
10 Diaphragm
Nitrile (NBR) 37B9720X012
Fluorocarbon (FKM) 23B0101X052
11 Body Seal O-Ring
Nitrile (NBR) 1H993806992
Fluorocarbon (FKM) 1H9938X0012
12 Insert Seal O-Ring
Nitrile (NBR) 1B885506992
Fluorocarbon (FKM) 1B8855X0012
13 Disk Assembly
Nitrile (NBR) 1E9848X0042
Fluorocarbon (FKM) 1E9848X0032
14 Stem, 316 SST 17B5278X012
16 Lever Assembly, 302 SST 1B5375000B2
17 Machine Screw (2 required) 19A7151X022
18 Guide Insert, 316 SST 27B4028X022
22 Closing Cap
Plastic (standard) T11069X0012
Steel 1E422724092
23 Hex Nut (8 required), Steel 1A352724122
24 Cap Screw (8 required), Steel 1A352524052
25 Gasket, (Steel closing cap only), Neoprene 1P753306992
26 Vent, Type Y602-1 (spring case up) 17A6570X012
35 Adjusting Screw, Cast Zinc 1B537944012
36 Washer, Steel 18B3440X012
38 Cap Screw, Steel 1B290524052
41 Back Disk Spring, 302 SST 1E984637022
42 Back Body Seal O-Ring
Nitrile (NBR) 13A1584X012
Fluorocarbon (FKM) 13A1584X022
43 Back Body Cap, 316 SST 1F2737X0012
44 Disk Spacer, 316 SST 1E9861X0012
45 Lower Head Gasket, Composition 18B3450X012
49 Backup Ring, 302 SST 18B3446X012
50 Lower Spring Seat, Steel 1B636325062
Types 66R and 66RR
The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their prospective owners. Fisher is a mark owned by Fisher Controls, Inc., a
business of Emerson Process Management.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specications of such
products at any time without notice.
Emerson Process Management does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Emerson
Process Management product remains solely with the purchaser.
©Emerson Process Management Regulator Technologies, Inc., 1980, 2009; All Rights Reserved
USA - Headquarters
McKinney, Texas 75069-1872 USA
Tel: 1-800-558-5853
Outside U.S. 1-972-548-3574
Asia-Pacic
Shanghai, China 201206
Tel: +86 21 2892 9000
Europe
Bologna, Italy 40013
Tel: +39 051 4190611
Middle East and Africa
Dubai, United Arab Emirates
Tel: +971 4811 8100
USA - Headquarters
McKinney, Texas 75069-1872 USA
Tel: 1-800-558-5853
Outside U.S. 1-972-548-3574
Asia-Pacic
Singapore, Singapore 128461
Tel: +65 6777 8211
Europe
Bologna, Italy 40013
Tel: +39 051 4190611
Gallardon, France 28320
Tel: +33 (0)2 37 33 47 00
USA - Headquarters
Elk River, Minnesota 55330-2445 USA
Tel: 1-763-241-3238
Europe
Selmsdorf, Germany 23923
Tel: +49 (0) 38823 31 0
For further information visit www.sherregulators.com
Figure 8. Type Y695RR Pilot Assembly
2
24
B2701
B2649_1
45 48 16 17 14
12 13
49 11 41 42
43144518
735226
36
26 38 25 50 10
3
