Emerson Ewv404 Owners Manual HF330UD.QX33

Emerson VCR EWV404 EWV404

a83e63ab-65cd-4e27-889e-6c631e7910a9 Emerson VCR EWV404 User Guide |

2015-01-05

: Emerson Emerson-Ewv404-Owners-Manual-165580 emerson-ewv404-owners-manual-165580 emerson pdf

Open the PDF directly: View PDF .
Page Count: 8

If channel 3 is already occupied for broadcasting,

1) Set your TV to channel 4.

2) Insert a pre-recorded tape into the VCR.

3) Press the PLAY button once.

4) After a few seconds, press the PLAY button on the VCR for 3 seconds.

•

The RF output channel will change to channel 4 from channel 3 and you will

see a playback picture.

• When a

picture does not appear on the TV screen, repeat step [4].

5) Press the STOP button to stop playback.

You can use the AUDIO OUT jack and

VIDEO OUT jack on the back of the

VCR if your TV has Audio/Video Input

jacks. In this case, you need to set the

TV to external Line Input Mode. Please

refer to your TV’s owner’s manual.

- 1 -

Owner’s Manual

Video Cassette Recorder

EWV404

If you need additional operating assistance after

reading this owner’s manual or to order replace-

ment accessories, please call

TOLL FREE : 1-800-256-2487

or visit our web site at http://www.funai-corp.com

0VMN04033 / HF331UD ★★★★★

Printed in China

ANT

AUDIO

VIDEO

OUT

OUT IN

ANT

AUDIO

VIDEO

OUT

OUT IN

AUDIO IN jack

Connect the audio cable from the audio out

jack of a camcorder, another VCR, or an

audio source.

VIDEO IN jack

Connect the video cable from the video out

jack of a camcorder, another VCR, or an

audio-visual source (laser disc player,

video disc player, etc.).

AUDIO OUT jack

Connect the audio cable to the audio in jack

of a camcorder, another VCR, a stereo

amplifier, or an audio system.

ANT IN jack

Connect your antenna or cable box.

ANT OUT jack

Connect the RF cable (supplied) to

the antenna input jack on your TV.

Front & Rear Terminals

Stereo TV Connection

ANT

OUT

AUDIO

ANT

OUT

VIDEO

Connect

Audio/Video Cables

(not supplied)

AUDIO OUTVIDEO

OUT

AUDIO INVIDEO

(Back of TV)

INOUT

(Back of VCR)

• Remote control

(NA372UD) with

Two AA batteries

• RF Cable

(WPZ0901TM002) • Owner’s Manual

(0VMN04033)

Supplied Accessory Installing the Batteries for

the Remote Control

Install two AA batteries

(supplied) matching the

polarity indicated on

the bottom of the

remote control.

Hint

• The RF output channel may

not change when you adjust

tracking during playback. In

this case, stop the playback,

and start the playback again.

After that, press the PLAY but-

ton on the VCR for 3 seconds

again.

VIDEO OUT jack

Connect the video cable to the video in jack

of a camcorder, another VCR, or a TV.

RF Output Channel

EMERSON AND THE G-CLEF LOGO ARE REGISTERED TRADEMARKS

OF EMERSON RADIO CORP., PARSIPPANY, NEW JERSEY, U.S.A.

CHANNEL

POWER

TAPE IN TIMER REC

VCR/TV

POWER

VIDEO AUDIO

1. Before using your VCR

ANT

OUT

RF Cable (supplied)

(Back of VCR)

(Back of TV) (Back of TV)

Plug the AC power cords of the VCR and TV into the AC outlets.

Disconnect

Antenna

Connect

Cable

Signal

Antenna

Cable

Signal

Basic VCR/TV Connection

Select this connection when you want to view or record a

scrambled channel.

With this connection, channels cannot

be changed on the VCR. You can view or record ONLY the

channels you have selected on the cable box or the satellite

box.

• While you are recording, only the recorded channel can

be viewed.

o select channels of the cable box or satellite box

1)Turn on the VCR by pressing the POWER button, and

then, press the VCR/TV button.The POWER and the

VCR/TV indicators on the front panel will light on. Then,

press the CHANNEL buttons to select channel 3 or 4

(the same channel as the output channel of the cable

box or satellite box).

•If you use the channel 4, you need to change the VCR’s

RF output to channel 4. Refer to “RF Output Channel”.

2) At the TV, select channel 3 or 4 (the same channel as

you have selected at step 1).

3) At the cable box or satellite box, select the channel you

want to view or record.

Select this connection when you want to change channels

on the VCR. With this connection, you may watch one

channel while recording another.

• You may not view or record a scrambled channel.

o select channels of the cable box or satellite box

1)At the cable box or satellite box, select channel 3 or 4

(the same channel as the VCR’s RF output channel.)

•Refer to “RF Output Channel”.

2)At the TV, select the same channel as the output chan-

nel (3 or 4) of the cable box or satellite box.

3)Turn on the VCR by pressing the POWER button, and

then, press the VCR/TV button .The POWER and

VCR/TV indicators on the front panel will light on. Then,

select the channel you want to view or record.

o play back a tape

Follow the steps 1) to 2) above. Then, play back a tape.

•Refer to “Playback” on page 5.

To view one channel while recording another

While you are recording on the VCR, press the VCR/TV but-

ton so that the VCR/TV indicator disappears on the VCR.

2)At the cable box or satellite box, select the channel you

want to view.

Hint for Cable Box or Satellite Box

ANT

OUT

RF Cable

(supplied)

(Back of VCR)

IN OUT

(Back of TV)

Cable

Signal

Connection A

(Cable box or

Satellite box)

ANT

OUT

RF Cable (supplied) RF Cable(Back of TV)

IN OUT

(Cable box or

Satellite box)

Cable

Signal

Connection B

(Back of VCR)

HF330UD.QX33 03.12.16 17:34 Page 1

- 2 - EN

2. Important Safeguards

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

The caution marking is located on the rear of the cabinet.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated "dangerous

voltage" within the product's enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

1. Read Instructions- All the safety and operating

instructions should be read before the appliance

is operated.

2. Retain Instructions- The safety and operating

instructions should be retained for future refer-

ence.

3. Heed Warnings- All warnings on the appliance

and in the operating instructions should be

adhered to.

4. Follow Instructions- All operating and use

instructions should be followed.

5. Cleaning- Unplug this video product from the

wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth

for cleaning.

EXCEPTION: A product that is meant for unin-

terrupted service and, that for some specific

reason, such as the possibility of the loss of an

authorization code for a CATV converter, is not

intended to be unplugged by the user for clean-

ing or any other purpose, may exclude the refer-

ence to unplugging the appliance in the clean-

ing description otherwise required in item 5.

6. Attachments- Do not use attachments not rec-

ommended by the video product manufacturer

as they may cause hazards.

7. Water and Moisture- Do not use this video

product near water, for example, near a bath

tub, wash bowl, kitchen sink, or laundry tub, in a

wet basement, or near a swimming pool, and

the like.

8. Accessories- Do not place this video product

on an unstable cart, stand, tripod, bracket, or

table. The video product may fall, causing seri-

ous injury to a child or adult, and serious dam-

age to the appliance. Use only with a cart,

stand, tripod, bracket, or table recommended by

the manufacturer, or sold with the video product.

Any mounting of the appliance should follow the

manufacturer's instructions and should use a

mounting accessory recommend-

ed by the manufacturer. An appli-

ance and cart combination should

be moved with care. Quick stops,

excessive force, and uneven sur-

faces may cause the appliance

and cart combination to overturn.

9. Ventilation- Slots and openings in the cabinet

are provided for ventilation and to ensure reli-

able operation of the video product and to pro-

tect it from overheating, and these openings

must not be blocked or covered. The openings

should never be blocked by placing the video

product on a bed, sofa, rug, or other similar sur-

face. This video product should not be placed in

a built-in installation such as a bookcase or rack

unless proper ventilation is provided or the man-

ufacturer's instructions have been adhered to .

10. Power Sources- This video product should be

operated only from the type of power source

indicated on the marking label. If you are not

sure of the type of power supply to your home,

consult your appliance dealer or local power

company. For products intended to operate from

battery power, or other sources, refer to the

operating instructions.

11. Grounding or Polarization- This video product

is equipped with a polarized alternating-current

line plug (a plug having one blade wider than

the other). This plug will fit into the power outlet

only one way. This is a safety feature. If you are

unable to insert the plug fully into the outlet, try

reversing the plug. If the plug should still fail to

fit, contact your electrician to replace your obso-

lete outlet. Do not defeat the safety purpose of

the polarized plug.

12. Power Cord Protection- Power supply cords

should be routed so that they are not likely to be

walked on or pinched by items placed upon or

against them, paying particular attention to

cords at plugs, convenience receptacles, and

the point where they exit from the appliance.

13. Outdoor Antenna Grounding- If an outside

antenna or cable system is connected to the

video product, be sure the antenna or cable sys-

tem is grounded so as to provide some protec-

tion against voltage surges and built-up static

charges. Article 810 of the National Electrical

Code, ANSI/NFPA No. 70, provides information

with regard to proper grounding of the mast and

supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of

grounding conductors, location of antenna-dis-

charge unit, connection to grounding electrodes,

and requirements for the grounding electrode.

(Fig. A)

14. Lightning- For added protection for this video

product during a lightning storm, or when it is

left unattended and unused for long periods of

time, unplug it from the wall outlet and discon-

nect the antenna or cable system. This will pre-

vent damage to the video product due to light-

ning and power-line surges.

15. Power Lines- An outside antenna system

should not be located in the vicinity of overhead

power lines or other electric light or power cir-

cuits, or where it can fall into such power lines

or circuits. When installing an outside antenna

system, extreme care should be taken to keep

from touching such power lines or circuits as

contact with them might be fatal.

16. Overloading- Do not overload wall outlets,

extension cords, or integral convenience recep-

tacles as this can result in a risk of fire or elec-

tric shock.

17. Object and Liquid Entry- Never push objects

of any kind into this video product through any

openings as they may touch dangerous voltage

points or short-out parts that could result in a

fire or electric shock. Never spill liquid of any

kind on the video product.

18. Servicing- Do not attempt to service this video

product yourself as opening or removing covers

may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service

personnel.

19. Damage Requiring Service- Unplug this video

product from the wall outlet and refer servicing

to qualified service personnel under the follow-

ing conditions:

a. When the power-supply cord or plug is dam-

aged.

b. If liquid has been spilled, or objects have fallen

into the video product.

c. If the video product has been exposed to rain or

water.

d. If the video product does not operate normally

by following the operating instructions. Adjust

only those controls that are covered by the

operating instructions as an improper adjust-

ment of other controls may result in damage

and will often require extensive work by a quali-

fied technician to restore the video product to its

normal operation.

e. If the video product has been dropped or dam-

aged in any way.

f. When the video product exhibits a distinct

change in performance-this indicates a need for

service.

20. Replacement Parts- When replacement parts

are required, be sure the service technician has

used replacement parts specified by the manu-

facturer or have the same characteristics as the

original part. Unauthorized substitutions may

result in fire, electric shock or other hazards.

21. Safety Check- Upon completion of any service

or repairs to this video product, ask the service

technician to perform safety checks to determine

that the video product is in proper operating

condition.

22. Heat- This video product should be situated

away from heat sources such as radiators, heat

registers, stoves, or other products (including

amplifiers) that produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

ANTENNA

LEAD WIRE ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND

CLAMP

GROUND CLAMP

ELECTRIC

SERVICE

EQUIPMENT

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

S2898A

HF330UD.QX33 03.12.16 13:19 Page 2

- 3 - EN

3. Preset for Use

LANGUAGE SELECT

BENGLISH [ON]

FRANCAIS

ESPAÑOL

Hint

•

Repeat these steps only if there was a

power failure or if the VCR has been

unplugged for more than 30 seconds.

Turn on the TV and set

it to channel 3.

•If channel 3 is already occupied for broad-

casting, see“RF Output Channel” section.

POWER

STOP

PLAY

3CH 01

AUTO SET UP

F.FWD

To Select a Channel

You can select a channel by directly

pressing the Number buttons on the

remote control.

Notes for using the Number but-

tons:

•

When selecting cable channels which

are higher than 99, enter channel

numbers as a three-digit number.(For

example: 117, press 1,1,7)

• You must precede single-digit

channel numbers with a zero (For

example: 02, 03, 04 and so on).

To Preset the Channel Again

1) Press the MENU button until the main

menu appears.

2) Select "CHANNEL SET UP" by pressing the

PLAY or STOP button. Then, press the

F.FWD button.

Select "AUTO SET UP" by pressing

the

PLAY or STOP button. Then, press the

F.FWD button. After scanning, the tuner

stops on the lowest memorized channel.

To Change the On-Screen Language

1) Press the MENU button until the main

menu appears.

2) Select "LANGUAGE SELECT" by pressing

the PLAY or STOP button. Then, press the

F.FWD button.

3) Select "ENGLISH" , "FRANCAIS" or

"ESPAÑOL" by pressing the PLAY or STOP

button. Then, press the C.RESET/EXIT but-

ton.

1-MENU-

TIMER PROGRAMMING

AUTO REPEAT [OFF]

BCHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

2CHANNEL SET UP

AUTO SET UP

BMANUAL SET UP

STOP

PLAY

3MANUAL SET UP

CHANNEL 30 (CATV)

ADD

4MANUAL SET UP

CHANNEL 30 (CATV)

ADD

STOP

PLAY

F.FWD

STOP

PLAY

F.FWD

1-MENU-

TIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

BCLOCK SET

LANGUAGE SELECT

2CLOCK SET

MONTH DAY YEAR

0 3 / – – – – – –

HOUR MINUTE AM/PM

– – : – – – –

STOP

PLAY

STOP

PLAY

F.FWD

3CLOCK SET

MONTH DAY YEAR

0 3 / 1 5 – – – –

HOUR MINUTE AM/PM

– – : – – – –

STOP

PLAY

F.FWD

4CLOCK SET

MONTH DAY YEAR

0 3 / 1 5 2 0 0 4

HOUR MINUTE AM/PM

– – : – – – –

STOP

PLAY

F.FWD

5CLOCK SET

MONTH DAY YEAR

0 3 / 1 5 MON 2 0 0 4

HOUR MINUTE AM/PM

0 5 : – – – –

STOP

PLAY

F.FWD

6CLOCK SET

MONTH DAY YEAR

0 3 / 1 5 MON 2 0 0 4

HOUR MINUTE AM/PM

0 5 : 4 0 – –

STOP

PLAY

F.FWD

7CLOCK SET

MONTH DAY YEAR

0 3 / 1 5 MON 2 0 0 4

HOUR MINUTE AM/PM

0 5 : 4 0 P M AM

BPM

STOP

PLAY

Hint

• To go back one step, press the REW button

(during the steps [2] to [7].)

• Your clock setting will be lost if there is a

power failure or if the VCR has been

unplugged for more than 30 seconds.

REW

F.FWD

Hint

• If you accidentally select Spanish or French

and need English: Press the MENU button

and choose SELEC. IDIOMA, or SELEC-

TION LANGUE. Press the F.FWD button,

and select ENGLISH. Finally, press the

C.RESET/EXIT button.

Select “ADD” or “DELETE”

Select the channel to be

added or deleted.

5 To exit the

menu.

C.RESET

EXIT

Select the current month

Select the current day

Select the current year

Select “AM” or “PM”

8 To exit the CLOCK SET

screen.

Select the current hour

Select the current minute

Yes

es Press the MENU

button to exit

• Refer to “Hint for Cable Box or

Satellite Box” section on page 1.

Do you connect the cable of the cable box or

the satellite box to the VCR’s ANT IN jack?

Yes

Clock Set UpTo Add/Delete ChannelsTurn on the VCR for the first time

TV ScreenRemote Control

F.FWD

• If the clock is not set, the

CLOCK SET screen

appears when you press

the MENU button. In this

case, go to step [2].

Please wait for a few minutes.

After scanning...

•The tuner stops on the lowest memorized

channel.

•You can select only the channels memorized

in VCR by using the CHANNEL buttons.

•If "AUTO SET UP" appears on the TV screen

again, check the cable connections. Then,

press the F.FWD button once again.

HF330UD.QX33 03.12.16 13:19 Page 3

- 4 - EN

4. Precautions

Specifications

CAUTION:

TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO

WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOC

ÉLECTRIQUES, INTRODUIRE LA

LAME LA PLUS LARGE DE LA

FICHE DANS LA BORNE CORRE-

SPONDANTE DE LA PRISE ET

POUSSER JUSQU’AU FOND.

Moisture Condensation Warning

Moisture condensation may occur inside

the unit when it is moved from a cold

place to a warm place, or after heating a

cold room or under conditions of high

humidity. Do not use the VCR at least for

2 hours until its inside is dry.

FCC Warning

This equipment may generate or use

radio frequency energy. Changes or

modifications to this equipment may

cause harmful interference unless the

modifications are expressly approved in

the instruction manual. The user could

lose the authority to operate this equip-

ment if an unauthorized change or modi-

fication is made.

Important Copyright Information

Unauthorized recording or use of broad-

cast television programming, video tape,

film or other copyrighted material may

violate applicable copyright laws. We

assume no responsibility for the unau-

thorized duplication, use, or other acts

which infringe upon the rights of copy-

right owners.

Install Location

For safety and optimum performance of

your VCR:

• Install the VCR in a horizontal and sta-

ble position. Do not place anything

directly on top of the VCR. Do not

place the VCR directly on top of the TV.

• Shield it from direct sunlight and keep

it away from sources of intense heat.

Avoid dusty or humid places. Avoid

places with insufficient ventilation for

proper heat dissipation. Do not block

the ventilation holes on the sides of the

VCR. Avoid locations subject to strong

vibration or strong magnetic fields.

Avoid the Hazards of Electrical Shock and

Fire

• Do not handle the power cord with wet

hands.

• Do not pull on the power cord when

disconnecting it from AC wall outlet.

Grasp it by the plug.

A Note about Recycling

This product's packaging materials are

recyclable and can be reused. Please

dispose of any materials in accordance

with your local recycling regulations.

Batteries should never be thrown away

or incinerated but disposed of in accor-

dance with your local regulations con-

cerning chemical wastes.

Note to the Cable TV System Installer

This reminder is provided to call the

Cable TV system installer’s attention to

Article 820-40 of the National Electrical

Code, which provides guidelines for

proper grounding – in particular, specify-

ing that the cable ground shall be con-

nected to the grounding system of the

building, as close to the point of cable

entry as possible.

Precautions

• Designs and specifications are subject to change without notice and legal obligation.

• If an explanation in the Owner’s Manual is not consistent across languages, please

refer to the English version.

CORRECTIVE ACTION

• Make sure the power plug is connected to an AC outlet.

• Make sure the power is turned on.

• Make sure the timer recording is set correctly.

• Make sure the power is off.

• Make sure the VCR clock is set correctly.

• Make sure the tape has a record tab. If needed, cover the hole with

cellophane tape.

• Adjust tracking control for a better picture by pressing the CHANNEL

buttons.

•

Head cleaning may be necessary. Refer to “Auto Head Cleaning” on

page 8.

• Make sure the VCR is not in the Menu mode.

• Turn on the TV and set the TV to channel 3. If channel 3 is already

occupied for broadcasting, change the RF output to channel 4, and

change the TV channel to channel 4. (See “RF Output Channel” on

page 1 for the detail.)

• Fine tune the channel reception on your TV.

• Re-check the ANT. IN and ANT. OUT connections. See page 1.

• Press the VCR/TV button on the remote control so that the VCR/TV

indicator on the VCR disappears.

• Make sure the power plug is connected to an AC outlet.

• Check batteries in remote control.

• You cannot copy a copyrighted video tape.You are experiencing copy

guard protection.

If you are having problems operating your product even though you have followed

the instructions in this manual, check the following list of problems and corrective

actions.You may be able to solve the problem yourself.

PROBLEM

No power.

Timer recording is impossible.

Cannot go into Recording mode.

Playback picture is partially noisy.

No playback picture (only sound

can be heard.)

No or poor playback picture.

TV programs cannot be seen nor-

mally.

No VCR operation from the

infrared Remote Control.

Video or color fades in and out when

making a copy of a video tape.

Video Heads : Four Heads

Operating temperature : 41°F~104°F

(5°C~40°C)

Converter output : VHF Channel 3 or 4.

Power requirement : 120V, 60Hz

Power consumption : 14 Watts

Dimensions : W 14-3/16” (360mm)

H 3-5/8” (92mm)

D 8-9/16” (216mm)

Weight : 4.0 lbs. (1.8 Kg.)

(approx.)

Troubleshooting Guide

HF330UD.QX33 03.12.16 13:19 Page 4

8. On-Screen Operations

1 To call up the main menu

6. Recording & OTR (One Touch Recording)

5. Playback

4 To exit the menu

- 5 -

-MENU-

BTIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

2 To select an item

-MENU-

TIMER PROGRAMMING

AUTO REPEAT [OFF]

BCHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

3 To decide

CHANNEL SET UP

AUTO SET UP

BMANUAL SET UP

CHANNEL

TAPE IN TIMER REC

VCR/TV

POWER

REC/OTR REW

F.FWD

STOP/EJECT

PLAY

PLAYB

POWER

VCR/TVEJECT

CHANNEL

PAUSE

/STILL

C.RESET

EXIT

-MODE

SLOW

DISPLAYSPEED

STOP

PLAY

REC/OTR

REW

F.FWD

123

456

Before:

Tu r n on the TV and set it to

channel 3.

•If channel 3 is already occupied for broad-

casting, see “RF Output Channel” section.

STOP EJECT A

TAPE IN

VCR/TV

POWER

Hint

•

When a tape without record tab is inserted, the VCR will start playback auto-

matically at step [1].

• Tracking will be automatically adjusted upon playback. To adjust the tracking manu-

ally, press the CHANNEL buttons.

TV ScreenRemote Control

PLAY

STOP

EJECT

Accidental erasure prevention

To prevent accidental recording on a record-

ed cassette, remove its record tab. To record

on it later, cover the hole with cellophane

tape.

Record tab

•Select the

desired channel

with tab

•Select the desired tape

speed

REC

Type of tape T60 T120 T160

SP mode 1hour 2hours 2-2/3hours

SLP mode 3hour 6hour 8hour

Tape Speed Recording/Playback Time

CH12

TV ScreenRemote Control

CHANNEL

123

456

SPEED

REC/OTR

REC OTR(0:30) OTR(1:00).....

(Normal recording)

OTR

(

8:00

)

OTR

(

7:30

)

STOP

EJECT

To cue or review picture during play-

back (Picture Search)

Press the F.FWD or REW button.

• Press it again and the VCR will now

search in super high speed. (in the

LP/SLP modes only)

To freeze the picture on TV screen

during playback (Still mode)

Press the PAUSE/STILL button.Each

time you press the button, the picture will

be forwarded by one frame.

• If the picture begins to vibrate vertically

during the still mode, stabilize the pic-

ture by pressing the CHANNEL buttons.

• If the picture is distorted or rolling verti-

cally, adjust the vertical hold control on

your TV, if equipped.

Counter Reset

Press the C.RESET/EXIT button.

To play back in slow motion

Press the SLOW button during playback

or the still mode.

• If the noise bar appears on the TV

screen, you can reduce it by pressing

the CHANNEL buttons.

To temporarily stop recording

(Pause mode)

Press the PAUSE/STILL button.

• During the rec pause mode, five

marks appear on the TV screen. Each

mark represents one minute.

• Press it again to resume recording.

Auto Rewind

When a tape reaches its end during play-

back, fast-forward, or recording (except

timer recording and One Touch

Recording), the tape will automatically

rewind to the beginning. After rewinding

finishes, the VCR will eject the tape and

turn itself to off.

Before:

Turn on the TV and set it to

channel 3.

•If channel 3 is already occupied for

broadcasting, see “RF Output Channel” section.

7. Other Operations

Hint

• Still/Slow/Pause mode will be automatically cancelled after 5 minutes to prevent damage to the tape and the

video head.

• To return to playback from the Picture Search/Still/Slow mode, press the PLAY button.

STOP

F.FWD

C.RESET

EXIT

CHANNEL

TAPE IN TIMER REC

VCR/TV

POWER

REC/OTR REW

F.FWD

STOP/EJECT

PLAY

POWER

VCR/TVEJECT

CHANNEL

PAUSE

/STILL

C.RESET

EXIT

-MODE

SLOW

DISPLAYSPEED

STOP

PLAY

REC/OTR

REW

F.FWD

123

456

CHANNEL

TAPE IN TIMER REC

VCR/TV

POWER

REC/OTR REW

F.FWD

STOP/EJECT

PLAY

POWER

VCR/TVEJECT

CHANNEL

PAUSE

/STILL

C.RESET

EXIT

-MODE

SLOW

DISPLAYSPEED

STOP

PLAY

REC/OTR

REW

F.FWD

123

456

REC

Hint

•If you have connected the VCR to a cable box or satellite box, refer to “Hint for

Cable Box or Satellite Box” section on page 1.

STOP EJECT A

PLAY

You can select a fixed recording time by press-

ing the REC/OTR button repeatedly.

TAPE IN

VCR/TV

POWER

HF330UD.QX33 03.12.16 13:19 Page 5

- 6 - EN

9. Recording Features

•Insert a tape with its record tab into the VCR.

F.FWD

8ONE TIME PROGRAM

PROGRAM NUMBER 4

DATE 0 5 / 0 3 MON

START TIME 0 7 : 3 0 PM

END TIME 0 8 : 3 0 PM

CHANNEL 1 6

REC SPEED – –

STOP

PLAY

9ONE TIME PROGRAM

PROGRAM NUMBER 4

DATE 0 5 / 0 3 MON

START TIME 0 7 : 3 0 PM

END TIME 0 8 : 3 0 PM

CHANNEL 1 6

REC SPEED SP BSP

SLP

F.FWD

2PROGRAM NUMBER 4

DATE – – / – –

START TIME – – : – – – –

END TIME – – : – – – –

CHANNEL – –

REC SPEED – –

STOP

PLAY

F.FWD

3PROGRAM NUMBER 4

BONCE

DAILY

WEEKLY

STOP

PLAY

F.FWD

4 Select the desired month

Select the desired day

ONE TIME PROGRAM

PROGRAM NUMBER 4

DATE 0 5 / 0 3 MON

START TIME – – : – – – –

END TIME – – : – – – –

CHANNEL – –

REC SPEED – –

F.FWD

STOP

PLAY

1-MENU-

BTIMER PROGRAMMING

AUTO REPEAT [OFF]

CHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

Select an empty program

number

Select “ONCE”, “DAILY”

(Mon-Fri), or “WEEKLY”

F.FWD

STOP

5 Select the desired start

time (hour)

Select the

minute

ONE TIME PROGRAM

PROGRAM NUMBER 4

DATE 0 5 / 0 3 MON

START TIME 0 7 : 3 0 – –

END TIME – – : – – – –

CHANNEL – –

REC SPEED – –

F.FWD

STOP

6ONE TIME PROGRAM

PROGRAM NUMBER 4

DATE 0 5 / 0 3 MON

START TIME 0 7 : 3 0 PM

END TIME – – : – – – –

CHANNEL – –

REC SPEED – – AM

BPM

STOP

PLAY

F.FWD

Select “AM” or “PM”

Repeat the procedure in steps

5 and 6 to set the end time.

Select the desired channel

Select the desired recording speed

Turn off the VCR

for recording

• TIMER indicator on the VCR lights up.

C.RESET

EXIT

POWER

Warning: Unauthorized recordings of copyrighted video tapes

may be an infringement of copyright laws.

Connect

OUT

AUDIO

VIDEOIN

OUT

ANT

VIDEO

OUT

INOUT

AUDIO

Audio/Video Cables

(not supplied)

RF Cable

(supplied)

(Back of TV)

(Back of Recording VCR*)

*Front input jacks are also available

(Back of Playing VCR)

Connect

1) Insert a pre-recorded tape into the playing VCR.

2) Insert a tape with its record tab into the recording VCR.

3) Press the SPEED button on the remote control of the recording VCR

to select the desired recording speed (SP/SLP).

4) Select the “L1” or “L2”position on the recording VCR.

• To use the input jacks on the back of the VCR, select "L1" position by

pressing [0], [0], [1] on the remote control or the CHANNEL buttons.

• To use the input jacks on the front of the VCR, select "L2" position by

pressing [0], [0], [2] on the remote control or the CHANNEL buttons.

5) Press the REC/OTR button on the recording VCR.

6) Begin playback of the tape in the playing VCR.

7) To stop recording, press the STOP/EJECT button on the recording

VCR, then stop playback of the tape in the playing VCR.

1) Turn the power on by pressing

the POWER button.

2) Select main menu by pressing

the MENU button.

3) Select "TIMER PROGRAM-

MING" by pressing the PLAY or

STOP button. Then, press the

F.FWD button.

4) Select the program number

which you want to check by

pressing the PLAY or STOP but-

ton. The details of the program

you selected will appear on the

TV screen.

• Go to the digit you want to

change by pressing the F.FWD

or REW button. Then, enter cor-

rect numbers by pressing the

PLAY or STOP button.

• You may cancel the entire pro-

gram by pressing the REW but-

ton while the program number

flashes.

5) Press the C.RESET/EXIT button

to exit.

6) Press the POWER button to

return to timer stand-by mode.

To Check, Correct, or Cancel a

Timer Program

Hint

• To go back one step, press the REW button

(during the steps [3] to [9].)

• If there is a power failure or the VCR has been unplugged for more than 30 sec-

onds, the clock setting and all timer settings will be lost.

• If the tape runs out before the end time, the VCR will switch to the Stop mode

immediately, eject the tape and the VCR power will be turned off. The TIMER

indicator will flash.

• If a tape is not in the VCR or does not have the record tab, the TIMER indicator

flashes and timer recording cannot be performed. Please insert a recordable tape.

• When all the Timer Recording are completed, the TIMER indicator flashes.

To play or eject the recorded tape, press the POWER button first,and then

press the PLAY or EJECT button.

Press the STOP/EJECT button on the VCR.

To cancel a Timer Recording that is in progress

Hint

• For best results during dubbing, use the VCR’s front panel controls whenever possible. The

remote control might affect the playing VCR’s operation.

• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are

not recommended.

• You can use a video disc player, satellite receiver, or other audio/video component with A/V out-

puts in place of the playing VCR.

• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)

Timer Recording Hint for Timer Recording

Copying a Video Tape

•

If you have connected the VCR to a cable

box or satellite box as the Connection A

on page 1, select the VCR to channel 3 or

4 (the RF output channel of the VCR).

Then, select the desired channel at the

cable box or satellite box. Leave the cable

box or satellite box on for timer recording.

PLAY

• You can program one

year in advance.

PLAY

STOP

PLAY

STOP

PLAY

HF330UD.QX33 03.12.16 13:19 Page 6

- 7 - EN

10. Special Features

You can specify the time for

fast forwarding or rewinding.

• Insert a tape into the VCR.

You can specify the number of

programs to be skipped.

• Insert a tape into the VCR.

1TIME SEARCH

– : – –

-MODE

2 Select the desired length

of time for fast forwarding

or rewinding

TIME SEARCH

2 : 5 0

STOP

PLAY

Hint f

Hint for

or Timer Sear

Timer Searc

ch & Inde

h & Index Sear

x Searc

• These functions are not available during recording.

• Press the STOP button to stop the search.

• If the end of the tape is reached during a Search, the VCR will cancel the search and rewind the

tape.

1INDEX SEARCH

– –

2INDEX SEARCH

0 3

STOP

PLAY

1-MENU-

TIMER PROGRAMMING

BAUTO REPEAT [OFF]

CHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

STOP

PLAY

2-MENU-

TIMER PROGRAMMING

BAUTO REPEAT [ON]

CHANNEL SET UP

CLOCK SET

LANGUAGE SELECT

F.FWD

Hint

• To cancel Auto Repeat, follow steps [1]-[2]

above. Then, press the F.FWD button so

that [OFF] appears beside AUTO REPEAT.

Press the C.RESET/EXIT button to exit.

• If menu remains on the TV screen at step

[3], press the C.RESET/EXIT button to exit.

You can repeat playback of a

whole tape automatically.

• Insert a tape into the VCR.

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5

02 01 01 02 03

Beginning

of tape

End

of tape

CURRENT PROGRAM

INDEX MARK

Time Search Index Search Auto Repeat

x2 (Twice)

-MODE

x1 (Once)

0:01~ 9:59

(1 minute~9 hours

and 59 minutes)

01 ~ 20

F.FWD

REW

To rewind To fast forward

After searching,

PLAYB

F.FWD

REW

To rewind To fast forward

After searching,

3 AUTO REPEAT B

PLAYBHint

Hint

• The VCR records an index mark at the

beginning of the recording when you make

a recording. There should be time gap

between index marks for the Index Search.

HF330UD.QX33 03.12.16 13:19 Page 7

11. Information

- 8 - EN

Servicing

Should your VCR become inoperative, do not

try to correct the problem by yourself. There

are no user-serviceable parts inside. Turn off,

unplug the power plug, and please call our

help line mentioned on page 1 to locate an

Authorized Service Center.

Cabinet Cleaning

• Wipe the front panel and other exterior sur-

faces of the VCR with a soft cloth immersed

in lukewarm water and wrung dry.

• Never use a solvent or alcohol. Do not spray

insecticide liquid near the VCR. Such chemi-

cals may cause damage and discoloration to

the exposed surfaces.

Auto Head Cleaning

• Automatically cleans video heads as you insert or

remove a cassette, so you can see a clear picture.

• Playback picture may become blurred or interrupt-

ed while the TV program reception is clear. Dirt

accumulated on the video heads after long peri-

ods of use, or the usage of rental or worn tapes

can cause this problem. If a streaky or snowy pic-

ture appears during playback, the video heads in

your VCR may need to be cleaned.

1. Please visit your local Audio/Video store and pur-

chase a good quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the

problem, please call our help line mentioned on

page 1 to locate an Authorized Service Center.

NOTES:

• Remember to read the instructions included with

the video head cleaner before use.

• Clean video heads only when problems occur.

PREPARACIÓN DE CANALES

(La antena o la caja de televisión por

cable deberá estar conectada)

NOTES: Cuando utilice su nueva

videograbadora por primera vez, o en el

caso de ser necesario después de pro-

ducirse un fallo en la alimentación, la

videograbadora se pondrá inicialmente en el

modo de preajuste cuando se pulse

[POWER].

1. Encienda el televisor y ponga el televisor

en el canal 3.

2. Pulse [POWER] para encender la

videograbadora.

3. Seleccione "ENGLISH",

"FRANCAIS"(French)

o "ESPAÑOL"

(Spanish) pulsando

[PLAY] o [STOP]. Y

luego pulse [F.FWD].

4. Pulse una vez

[F.FWD].

El sintonizador explora

y memoriza todos los canales activos de su

zona. Tras la exploración, el sintonizador se

detiene en el canal memorizado más bajo.

PREPARACIÓN DEL RELOJ

1. Pulse [MENU] hasta que aparezca el

menú principal. (Si el reloj no está puesto

en hora y se pulsa [MENU], el menú

AJUSTE DE RELOJ aparece en primer

lugar. En este caso, siga el paso 3.)

2. Pulse [PLAY] o [STOP] para indicar a

"AJUSTE DE RELOJ". Luego, pulse [F.FWD].

• Para volver atrás un

paso, pulse [REW].

4. Pulse [F.FWD] para

poner en fun-

cionamiento el reloj.

Ajuste el mes.

Ajuste el día.

Ajuste el año.

Ajuste el minuto.

Ajuste la

mañana (AM) o

la tarde (PM).

Ajuste la hora.