Emerson Ift9701 Users Manual Transmitter Installation

2015-01-05

• Chapter 1
  • Before You Begin
    • 1.1 About this manual
    • 1.2 Safety
    • 1.3 European installations
    • 1.4 Definitions
    • 1.5 Flowmeter components
• Chapter 2
  • Getting Started
    • 2.1 Safety, reliability, accessibility
      • 2.1.1 Hazardous area
      • 2.1.2 Orientation and mounting
      • 2.1.3 Temperature, humidity, and vibration
      • 2.1.4 Visibility of tags
    • 2.2 Transmitters approved for ATEX Zone 1
    • 2.3 Jumper settings
      • 2.3.1 Security
      • 2.3.2 Fault output levels
      • 2.3.3 Re-installing the circuit board compartment cover
• Chapter 3
  • Remotely Mounting the Transmitter
    • 3.1 Overview
    • 3.2 Choosing the proper location
    • 3.3 Mounting the transmitter
      • 3.3.1 Guidelines for flat-surface mounting
      • 3.3.2 Guidelines for pole mounting
    • 3.4 Connecting the transmitter to the sensor
      • 3.4.1 Cable types
      • 3.4.2 Guidelines for conduit
      • 3.4.3 Guidelines for cable gland
      • 3.4.4 Wiring connections to sensor
• Chapter 4
  • Power Supply and Output Wiring
    • 4.1 Overview
    • 4.2 Wiring guidelines
    • 4.3 Connect power supply wiring
    • 4.4 Connect output wiring
      • 4.4.1 Milliamp output
      • 4.4.2 Milliamp output connected to Bell 202 multidrop network
      • 4.4.3 Communication tools connected to milliamp output
      • 4.4.4 Pulse output
• Chapter 5
  • Flowmeter Startup
    • 5.1 Overview
    • 5.2 Customer service
    • 5.3 Startup procedures
    • 5.4 Initialization
      • 5.4.1 Diagnostic LED
      • 5.4.2 Optional display
      • 5.4.3 Startup mode
      • 5.4.4 Operating mode
    • 5.5 Flowmeter zeroing
      • 5.5.1 Zeroing procedure
      • 5.5.2 Diagnosing zero failure
    • 5.6 Configuration, calibration, and characterization
    • 5.7 Process measurement
• Chapter 6
  • Configuration with a HART Communicator
    • 6.1 Configuration overview
    • 6.2 Configuration parameters
      • 6.2.1 HART tag
      • 6.2.2 Measurement units
      • 6.2.3 Flow cutoff
      • 6.2.4 Damping
      • 6.2.5 Flow direction
      • 6.2.6 Range values for milliamp output
      • 6.2.7 Pulse output scaling
    • 6.3 Calibration procedures
      • 6.3.1 Auto zero
      • 6.3.2 Flow calibration procedure
    • 6.4 Characterization
• Chapter 7
  • Configuration with ProLink II Software
    • 7.1 Configuration overview
    • 7.2 Configuration parameters
      • 7.2.1 HART tag
      • 7.2.2 Process variable measurement
      • 7.2.3 Output configuration
    • 7.3 Calibration procedures
      • 7.3.1 Auto zero
      • 7.3.2 Flow calibration procedure
    • 7.4 Characterization
• Chapter 8
  • Troubleshooting
    • 8.1 Customer service
    • 8.2 General guidelines
    • 8.3 Transmitter diagnostic tools
      • 8.3.1 Diagnostic LED
      • 8.3.2 Optional LCD
      • 8.3.3 Fault outputs
    • 8.4 Power supply
    • 8.5 Wiring
    • 8.6 Over range and sensor failure conditions
    • 8.7 Slug flow
    • 8.8 Transmitter failure
    • 8.9 Digital diagnostic messages
• Appendix A
  • IFT9701 Specifications
    • A.1 Performance specifications
    • A.2 Functional specifications
      • A.2.1 Output signals
      • A.2.2 Local display (optional)
      • A.2.3 Low-flow cutoff
      • A.2.4 Slug-flow inhibit
      • A.2.5 Damping
      • A.2.6 Fault indication
      • A.2.7 Output testing
      • A.2.8 Power supply options
    • A.3 Environmental limits
      • A.3.1 Temperature
      • A.3.2 Process fluid temperature limits
      • A.3.3 Humidity limits
      • A.3.4 Vibration limits
    • A.4 Density limits
    • A.5 Environmental effects
    • A.6 Ambient temperature effect on milliamp output
    • A.7 Shipping weight
    • A.8 Hazardous area classifications
• Appendix B
  • HART Communicator Menu Trees
• Appendix C
  • Installing the Optional Display
• Appendix D
  • Return Policy
    • D.1 General guidelines
    • D.2 New and unused equipment
    • D.3 Used equipment
• Index