Emerson Network Router Users Manual ProLink II Software For Micro Motion Transmitters

2015-01-05

• Contents
• Before You Begin
  • 1.1 About this manual
  • 1.2 About ProLink II software
    • 1.2.1 Supported transmitters
    • 1.2.2 Uses of ProLink II
  • 1.3 ProLink II requirements
    • 1.3.1 PC requirements
    • 1.3.2 Installation kits
  • 1.4 Determining your transmitter type
  • 1.5 Micro Motion customer service
• Installation and Setup
  • 2.1 Overview
  • 2.2 Installation and setup
    • 2.2.1 Ensure required privileges
    • 2.2.2 Install the ProLink II software
    • 2.2.3 Generate the temporary license
    • 2.2.4 Determine your connection type
    • 2.2.5 Install the signal converter and connect the wires
    • 2.2.6 Configure ProLink II connection parameters and connect to the transmitter
    • 2.2.7 Obtain and configure a site key
  • 2.3 Troubleshooting the ProLink II installation
    • 2.3.1 Insufficient privileges
    • 2.3.2 Missing or corrupt registry entries
  • 2.4 Troubleshooting the ProLink II connection
    • 2.4.1 OPC server or OPC client issues
    • 2.4.2 Other issues
• Using ProLink II Software
  • 3.1 Overview
  • 3.2 ProLink II user interface
  • 3.3 Startup
    • 3.3.1 Connecting to a transmitter
    • 3.3.2 Disconnecting
  • 3.4 ProLink II help system
  • 3.5 Viewing installed options
  • 3.6 Viewing process data
  • 3.7 Viewing and resetting totalizers and inventories
  • 3.8 Viewing meter status
  • 3.9 Viewing and acknowledging alarms
    • 3.9.1 Viewing alarms
    • 3.9.2 Acknowledging alarms
  • 3.10 Managing the ProLink II license
    • 3.10.1 Transferring to same PC
    • 3.10.2 Transferring to different PC
• Initial Transmitter Startup Procedures
  • 4.1 Overview
  • 4.2 Loop tests
  • 4.3 Trimming the milliamp (mA) output(s)
  • 4.4 Zeroing the meter
• Transmitter Configuration, Characterization, and Calibration
  • 5.1 Overview
  • 5.2 Using configuration files
    • 5.2.1 Saving a configuration file to a PC
    • 5.2.2 Loading a configuration file to a transmitter
  • 5.3 Configuring a transmitter
    • 5.3.1 Using the Gas Unit Configurator tool
  • 5.4 Characterizing the meter
    • 5.4.1 When to characterize
    • 5.4.2 Characterization parameters
    • 5.4.3 How to characterize
  • 5.5 Calibrating the meter
    • 5.5.1 When to calibrate
    • 5.5.2 Density calibration
    • 5.5.3 Temperature calibration
  • 5.6 Compensating for pressure
    • 5.6.1 Options
    • 5.6.2 Pressure correction factors
    • 5.6.3 Configuration
  • 5.7 Compensating for temperature
  • 5.8 Configuring polling
• Meter Verification
  • 6.1 Overview
  • 6.2 Running the meter verification test
    • 6.2.1 First panel: Sensor and Transmitter Configuration
    • 6.2.2 Second panel: Test Definition
    • 6.2.3 Third panel: Start
    • 6.2.4 Fourth panel: Test Results
    • 6.2.5 Fifth panel: Report
• Data Logger
  • 7.1 Overview
  • 7.2 Using Data Logger
    • 7.2.1 Defining the log file
    • 7.2.2 Specifying log contents
    • 7.2.3 Starting and stopping the logging function
    • 7.2.4 Data Logger tools
• Transmitter Terminal Reference
  • A.1 Overview
  • A.2 Transmitter terminal diagrams
• Configuring the Discrete Batch Application
  • B.1 About this appendix
  • B.2 About discrete batching
  • B.3 Discrete batch configuration
    • B.3.1 Flow source
    • B.3.2 Control options
    • B.3.3 Configure presets
    • B.3.4 Batch control methods
  • B.4 Running a batch
  • B.5 Performing Batch AOC calibration
• Index