Emerson Rosemount 3300 Series Users Manual Book_3300_CA

2015-01-05

• Table of Contents
• Section 1 Introduction
  • Safety Messages
  • Manual Overview
  • Service Support
• Section 2 Transmitter Overview
  • Theory of Operation
  • Applications
  • Components of the Transmitter
  • System Architecture
  • Probe Selection Guide
    • Dead Zones
  • Process Characteristics
    • Coating
    • Bridging
    • Foam
    • Vapor
    • Measuring Range
    • Interface
  • Vessel Characteristics
    • Heating Coils, Agitators
    • Tank Shape
• Section 3 Installation
  • Safety messages
  • Installation Procedure
  • Before You Install
    • Alarm and Write Protection Switches
  • Mounting Considerations
    • Process Connection
    • Installation of Single Lead Probes in Non-metallic Tanks
    • Mounting in Still pipes/by-pass pipes
    • Free Space
    • Recommended Mounting Position
    • Insulated Tanks
  • Mechanical Installation
    • Shortening the Probe
    • Anchoring
    • Mounting a Centering Disc for Pipe Installations
  • Electrical Installation
    • Cable/conduit entries
    • Grounding
    • Cable Selection
    • Hazardous Areas
    • Power Requirements
    • Maximum Loop Resistance
    • Connecting the Transmitter
    • Non-Intrinsically Safe Output
    • Intrinsically Safe Output
  • Optional Devices
    • Tri-Loop
    • Using More than one transmitter on the bus
    • 751 Field Signal Indicator
• Section 4 Start-Up
  • Safety messages
  • Configuration Parameters
    • Basic Configuration
    • Volume Configuration
  • Configuration using a 375 Field Communicator
  • Basic Configuration
    • Transmitter Variables
    • Measurement Units
    • Reference Gauge Height
    • Probe Length
    • Probe Type
    • Product Dielectric
    • Vapor Dielectric
    • Measurement Mode
    • Probe Angle
    • Maximum Upper Product Thickness
    • Damping
    • Display Panel
    • 4 and 20 mA Points
  • Volume Configuration
    • Transmitter Variables
    • Volume Units
    • Tank Type
    • Tank Dimensions
    • Strapping Table
  • Configuration using The Radar Configuration Tool
    • Installing the RCT software
    • Specifying the COM Port
    • Help In RCT
    • Using the Setup Wizard
    • Using the Setup Function
    • Setup - Info
    • Setup - Basics
    • Setup - Output
    • Setup - Tank Config
    • Setup - Volume
    • Setup - LCD
  • Special Functions
    • TriLoop
• Section 5 Operating the Display Panel
  • Display Functionality
  • Error Messages
  • Alarm and Write Protection
• Section 6 Service and Troubleshooting
  • Safety messages
  • Advanced Configuration
    • User defined Upper Reference Point
    • Plotting the Measurement Signal
    • Interface Measurements for Semi-Transparent Bottom Products
    • High Level Rates
    • Interface Measurements with Fully Immersed Probes
  • Service
    • Analog Output Calibration
    • Level and Distance Calibration
    • Disturbances at the Top of the Tank
    • Amplitude Threshold Settings
    • Logging Measurement Data
    • Saving the Transmitter Configuration
    • Removing the Transmitter Head
    • Changing the Probe
  • Diagnostic Messages
    • Troubleshooting
    • Errors
    • Warnings
• Appendix A Reference Data
  • Specifications
    • Process Temperature and Pressure Rating
    • Ambient Temperature
  • Dimensional drawings
  • Ordering Information
  • Spare Parts
• Appendix B Product Certifications
  • Safety Messages
  • EU Conformity
  • European ATEX Directive Information
    • Intrinsic Safety
    • Flameproof
  • Hazardous Locations Certifications
    • Factory Mutual (FM) Approvals
    • Canadian Standards Association (CSA) Approval
    • IECEx Approval
  • Combination of Approvals
  • Approval Drawings
• Index
  • Numerics
  • A
  • B
  • C
  • D
  • E
  • F
  • G
  • H
  • I
  • L
  • M
  • N
  • P
  • R
  • S
  • T
  • U
  • V
  • W