Emerson File

User Manual: Emerson s - Owner's Manuals | Emerson Radio

Open the PDF directly: View PDF PDF.
Page Count: 14

213
Battery installation (Remote Control)
The remote control requires one
"button-type" 3-volt lithium battery,
included. To extend the life of the
original battery we have inserted
a small clear plastic spacer tab
between the lithium battery and the
battery terminal.
You must remove this battery spacer
tab before you can use the remote
control.
To remove the tab, pull it in the
direction of the arrow in the illustration
as shown.
When the operation of the remote control becomes intermittent
or unsatisfactory, replace the original battery with a new 3-volt
lithium battery.
The battery number is (CR2025) or equivalent.
To replace the battery, remove the screw at the back of the
remote control with an appropriate screwdriver and open the
battery cover.
Remove the original battery from the battery compartment and
install a new (CR2025) battery with the " + " side facing up as
shown in the illustration. Then put the battery cover and screw
back to its original place.
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of the original battery properly. It should not be
thrown into a fire as the battery may explode if incinerated.
It should not be left around where small children or pets
might play with, or swallow it. If the battery is accidentally
swallowed, contact a physician immediately.
California Use Only:
The Perchlorate warning applies only to primary
CR(Manganese Dioxide) Lithium coin cells sold or distributed
ONLY in California,USA. "Perchlorate Material-special
handling may apply." See
www.dtsc.ca.gov/hazardouswaste/perchlorate
Installation
This section describes how to connect the system to a TV monitor with audio/video input jacks. You cannot connect this system
to a TV monitor which does not have a video input connector. Be sure to turn off the power of each component before making
the connections.
Unpacking
Check that you have the following items:
•Main unit (1).
•Remote control (1).
•Audio/Video cable (4 feet x 1).
•Owner’s Manual (1).
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent
the product from moving when you operate the controls.
These 'feet' are made from non-migrating rubber material
specially formulated to avoid leaving any marks or stains on
your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause
the rubber 'feet' to soften, and leave marks or a rubber
residue on the furniture. To prevent any damage to your
furniture we strongly recommend that you purchase small
self-adhesive felt pads, available at hardware stores and
home improvement centers everywhere, and apply these
pads to the bottom of the rubber 'feet' before you place the
product on fine wooden furniture.
Remove
before use
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM13
14
TV and Optional Component
Connections
Required cords
•Video cord for connecting a TV set (included).
•Audio cords (included).
When connecting a cord, be sure to match the color-coded
pins to the appropriate jacks on the components.
Notes:
• TV Connection-Normal (Connection Cable Included):
To view the video from DVD discs on your TV set connect the
Video Out jack of this system to the Video ln jack of your TV
set. The Video jacks are usually colored yellow. Use the
included video cable with yellow plugs on each end.
• TV Connection-Audio (Connection Cables Included):
Connect the Left/Right audio output jacks of your system
to the Left/Right audio input jacks of the TV set.
• External Decoder Connection-Not Required:
The Coaxial Digital Audio output jack allows digital audio
signals to be fed to an external Dolby Digital decoder if
desired. The Coaxial digital audio connection cable is not
included.
Connecting the AC Power Cord
Notes:
•The Power Requirement is: AC 120V, 60Hz.
•Connecting to power other than the one listed above may
damage the system or cause abnormal operation.
•Before connecting the AC power cord of this system to a
wall outlet, connect the speakers and other component
cables to the system.
•Connect the AC power cords of your TV and any optional
connect to a wall outlet.
TV
AUDIO
IN
VIDEO IN
R L
AV Amplifier with a
Dolby Digital Decoder
COAXIAL
IN
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM14
415
DVD Playback
Preparations
•Switch on the TV set power and select "Video" as the TV
input.
•Switch on the stereo system's power if the player has
been connected to a stereo system.
Basic Play
1. Pull open the vertical disc compartment.
2. Place a disc into the disc compartment.
Hold the disc without touching either of its surfaces and
with the printed title side facing up. Align it with the guides
and place it in its proper position.
3. Push close the vertical disc compartment.
4. Press the PLAY button if the movie has not started
automatically.
•If the disc has one or more titles recorded on it, a menu
screen will appear on the TV screen after a few moments.
5. Select the preferred title by using the (,,,) Navigation
buttons, followed by the ENTER button, or press the number
button corresponding to the menu.
•Play of the seleted title now commences.
When the menu continues onto another screen
After step 3 on previous page, press SKIP .
•To return to the previous menu screen, press SKIP .
•For further details, refer also to the disc jacket.
Stopping play and returning to the menu screen
Press the DVD MENU button.
•Play is suspended and the menu screen is displayed.
When the unit is not in use
When the unit is not in use, remove the disc and press the
Standby button to turn off the power. The STANDBY indicator
will illuminate.
Notes:
•The disc continues to rotate while the menu is displayed
even after the player has finished playing a particular item.
When no further selections are to be played, be sure to
press the STOP button to clear the menu display.
•If the disc is placed in upside down, the On Screen Display
will indicate "NO DISC".
For your reference
•When " " appears on the TV screen while a button is
being operated, it means that the corresponding operation
is prohibited by the player.
Stopping play
•Press the STOP button.
For your convenience
•When play is stopped, the unit records the point when
STOP was pressed (RESUME function). Press PLAY
again and play will resume from this point. When the tray is
opened or STOP is pressed again, the RESUME function
will be cleared. The RESUME function works only with discs
for which the elapsed playing time appears during playback.
Still picture
Press the PAUSE/STEP button during play.
To return to normal play
Press PLAY .
Frame advance
•Press the PAUSE/STEP button to advance to still picture
mode.
•Press the PAUSE/STEP button repeatedly until the desired
frame is displayed. The disc is advanced one frame each
time the PAUSE/STEP button is pressed.
Skipping Chapters or Tracks
Skipping ahead
Press SKIP during play.
•A chapter is skipped each time the button is pressed.
Skipping back
Press SKIP during play.
Slow-motion Play by Remote Control
Only
While a disc is playing, press PAUSE/STEP followed by FWD..
Each time you press FWD. , the slow motion will get even
slower until you reach the slowest speed.
To return to normal play
•Press PLAY button.
Search: rapid advance-rapid reverse
Press the SEARCH or button(s). Each time you press the
button, the speed change from: x2, x4, x8, x16.
BACKWARD x2 = Fast Reverse 1
BACKWARD x4 = Fast Reverse 2
BACKWARD x8 = Fast Reverse 3
BACKWARD x16 = Fast Reverse 4
FORWARD x2 = Fast Forward 1
FORWARD x4 = Fast Forward 2
FORWARD x8 = Fast Forward 3
FORWARD x16 = Fast Forward 4
To return to normal play
•Press the PLAY button.
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM15
16
Selecting a Start Point using the
Chapter Time Code
Example: Viewing after 1 hour 3 minutes have elasped from
the chapter start.
1. Press the SEARCH button thirdly during play.
2. Press the Number button(s) to select the preferred chapter.
Example: To specify 1 hour 3 min 00 sec, press ' 1 ', ' 0 ', ' 3 ',
' 0 ', ' 0 '.
3. Play now commences from Title 2.
Note: Depending on the disc used, it may not be possible to
perform these operations during DVD menu play.
For your reference
" INPUT INVALID" appears on the TV screen if the number
selected does not exist on the disc.
Repeat Playback (CD)
1. Press the REPEAT/A-B button once and " Track"
indicator will appear on the TV screen. The selected track
will be repeated indefinitely unless the STOP button is
pressed.
2. Press the REPEAT/A-B button twice and " ALL" indicator
will appear on the TV screen. The entire disc will be
repeated indefinitely unless the STOP button is pressed.
3. Press the REPEAT/A-B button again to resume normal
playback.
Repeat Playback (DVD)
1. Press the REPEAT/A-B button during play as follow:
REPEAT x1 = Repeat Chapter
REPEAT x2 = Repeat Title
REPEAT x3 = Repeat Off
Note: Repeat play may not work correctly with some DVDs.
Selecting Scenes by Chapter Number
Example: Starting play from Chapter 03.
1. Press the SEARCH button during play.
2. Press the Number button(s) to select the preferred chapter.
Example: Press ' 0 ' , ' 3 '.
3. Play now commences from Chapter 03.
Note: Depending on the disc used, it may not be possible to
perform these operations during DVD menu play.
For your reference
" INPUT INVALID" appears on the TV monitor if the number
selected does not exist on the disc.
Selecting a Start Point using the Title
Time Code
Example: Viewing after 1 hour 3 minutes have elapsed from
the title start.
1. Press the SEARCH button twice during play.
2. Press the Number button(s) to specify the starting position.
Example: To specify "1 hour 3 min.00sec.", press ' 1 ', ' 0 ', ' 0 ',
' 3 ', ' 0 ', and ' 0 '.
3. Play now commences from the specified position.
Notes:
•This operation works only with discs for which the elapsed
playing time appears during playback.
•For some discs, play may not start from the specified
position even when the steps above have been performed
correctly.
•Depending on the disc used, it may not be possible to
perform these operations during DVD menu play.
TT 01/03 CH /06
TT 01/03 CH 03/06
TT 01/03 T : :
TT 01/03 T 1:03:00
CH 01/06 T : :
CH 01/06 T 1:03:00
Chapter
Title
Off
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM16
617
Repeat sections between two specific
points (Repeat/A - B)
1. Press the REPEAT/A-B button during play at the point where
repeat play is to commence (A).
2. Press the REPEAT/A-B button again at the point where repeat
play is to be concluded (B).
Repeat play of the selection between points A and B starts
automatically. The section from point A to point B will play
repeatedly.
To return to normal play
•Press the REPEAT/A-B button again.
Note: Some subtitles recorded around point A or B may fail to
appear.
CD-R/RW Playback
Important Information
The DVD player in this system can play normal audio CDs,
recordable CDs (CD-Rs), re-writable CD's (CD-RWs). However,
because of the non-compatibility of certain ripping/burning solf-
ware used to record CDs, and the quality of the blank discs used
for recording, 100% playability of CD-RW cannot be guaranteed.
This is not an indication of any problem with your system.
Picture CD Operation
1. After loading a picture CD disc into the disc tray, the picture
CD menu will appear on the TV screen.
2. Press the (,) Navigation buttons to select your desired
folder.
3. Press the ENTER button to confirm your selection and start
the playback of picture CD disc.
A
AB
00:00 00:00
001_00A
/
002_0A
003_1A
004_2A
005_3A
006_4A
Convenient Functions
Changing Audio Soundtrack
Language
It is possible to change the audio soundtrack language from
English to a different language, if available. (This operation
works only with discs on which multiple audio soundtrack
languages are recorded.)
1. Press the AUDIO button during play.
2. Press the AUDIO button repeatedly to select the preferred
language.
For your reference
•The choice of languages is limited to those that are
available on the disc being played. All discs do not have all
languages available.
•When the power is turned on or the disc is removed, the
language heard is the one selected initially. If this
language is not recorded on the disc, only the language
available on the disc will be heard.
•The unit is factory preset to ENGLISH.
Viewing from another Angle
Some DVD discs may contain scenes which have been shot
simultaneously from a number of different angles. For these
discs, the same scene can be viewed from each of these
different angles using the ANGLE button. (The recorded angles
differ depending on the disc used.)
1. Press the ANGLE button during play.
2. Press the ANGLE button to select the preferred angle.
Note: This function will only work on discs where different
angles have been recorded.
Clearing & Displaying of Subtitles
If a disc has subtitles recorded on it, they can either be
displayed or cleared on the TV screen. (This operation works
only with discs on which the subtitle language is recorded.)
•Press the SUBTITLE button during play.
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM17
18
Audio CD Playback
Preparation
•Switch on the TV set power and select "Video" as the TV
input.
•Switch on the stereo system's power if the player has been
connected to a stereo system.
Basic Play
1. Pull open the vertical disc compartment.
2. Place a disc into the disc compartment.
Hold the disc without touching either of its surfaces and
position it with the printed title side facing up. Align it with
the guides and place it in its proper position.
3. Push close the vertical disc compartment.
4. Press the PLAY button.
Note: Make sure the TV type is set to NTSC (factory default).
When the unit is not in use
When the unit is not in use, remove the disc and press the
Standby button to turn off the power. The STANDBY indicator
will illuminate.
Notes:
•The disc continues to rotate while the menu is displayed
even after the player has finished playing a particular item.
When no further selections are to be played, be sure to
press the STOP button to clear the menu display.
•If the disc is placed in upside down, the On Screen Display
will indicate "NO DISC".
For your reference
•When " " appears while a button is being operated, it
means that the corresponding operation is prohibited by
the player.
For your convenience
When play is stopped, the unit records the point where
STOP was pressed. Press PLAY again, and play will
resume from this point. When the tray is opened, the
RESUME function will be cleared. The RESUME function
works only with discs for which the elapsed playing time
appears during playback.
Still Picture (PAUSE/STILL)
•Press the PAUSE/STEP button during play.
Audio CD
•The player will be placed in the pause mode.
To return to normal play
•Press PLAY button.
Changing Subtitle Language
It is possible to change the subtitle language from English to a
different language, if available. (This operation works only with
discs on which multiple subtitle languages are recorded.)
1. Press the SUBTITLE button during play.
2. Press the SUBTITLE button repeatedly to select the preferred
language.
Notes:
•In some cases, the subtitle language is not changed
immediately to the selected one.
•When the power is turned off or the disc is removed,
subtitles appear in the language selected at the initial
settings. If this language is not recorded on the disc, they
will appear in the disc's priority language.
Selection of Titles
Some DVDs may have more than 1 movie (Title) on them. If the
disc has a title menu recorded on it, the TITLE button can be
used to select the desired title. (The details of operation differ
depending on the disc used.)
1. Press the TITLE button during play. A list of titles on the disc
is now displayed.
2. Press the (,,,) Navigation buttons to select the
preferred title.
3. Press the ENTER button. The selected title now starts
playing.
Using a DVD Menu
Some DVD discs have unique menu structures called DVD
menus. For example, DVDs programmed with complex contents
provide guide menus and those recorded with various languages
provide menus for audio and subtitle language. Although the
DVD menu's contents and operation differ from disc to disc, the
following explains the basic operation when this feature is used.
1. Press the DVD MENU button during play. The DVD menu
available on the disc is now displayed.
2. Press the (,,,) Navigation buttons to select the
preferred menu.
3. Press the ENTER button. The selected item is now executed.
When the menu continues onto another screen
Repeat step 2 and 3.
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM18
819
Settings and Adjustments
Once the initial setup has been completed, the player can
always be operated under the same conditions. The settings
will be retained in the memory, until the settings are changed.
TV Display
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select General.
3. Use the (,) Navigation buttons to move the cursor to the
TV Display item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between Normal/PS (Pan &
Scan), Normal/LB (Letterbox), and Wide formats.
Normal/PS (Pan & Scan):
Video material formatted in the PAN & SCAN style is played
in that style (the left and right edges are cut off).
Normal/LB (Letterbox):
Video material not formatted in the Letterbox style is played
in the Pan & Scan style.
Wide:
Select this for a wide screen TV set.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
TV Type
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select General.
3. Use the (,) Navigation buttons to move the cursor to
the TV Type item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between NTSC, and PAL
modes.
- - General Setup Page - -
Set TV Display Mode
PreferenceDolby
General Audio
TV Display
TV Type
Angle Mark
OSD Lang
Captions
Screen Saver
PS
NTSC
ON
ENG
ON
ON
Normal/PS
Normal/LB
Wide
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
Angle Mark
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select General.
3. Use the (,) Navigation buttons to move the cursor to the
Angle Mark item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between On and Off modes.
This only works when there is an angle mark on the disc.
Note: Select "On" the screen shows the angle mark when
playing a DVD.
Select "Off" the angle mark is not shown.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
- - General Setup Page - -
Set TV Standard
PreferenceDolby
General Audio
TV Display
TV Type
Angle Mark
OSD Lang
Captions
Screen Saver
PS
NTSC
ON
ENG
ON
ON
NTSC
PAL
- - General Setup Page - -
Set Angle Mark
PreferenceDolby
General Audio
TV Display
TV Type
Angle Mark
OSD Lang
Captions
Screen Saver
PS
NTSC
ON
ENG
ON
ON
On
Off
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM19
20
On Screen Display Language
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select General.
3. Use the (,) Navigation buttons to move the cursor to the
OSD Lang item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between English, German,
Spanish and French on screen display languages.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
Captions
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select General.
3. Use the (,) Navigation buttons to move the cursor to the
Captions item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between On and Off modes.
•Select this option when some newer DVD movies include
closed captioning for hearing impaired viewers.
Note: Select "On" to switch on the captioning feature that
describes other sounds being heard together with
the dialog.
Select "Off" the closed captions will not appear.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
- - General Setup Page - -
Set OSD Language
PreferenceDolby
General Audio
TV Display
TV Type
Angle Mark
OSD Lang
Captions
Screen Saver
PS
NTSC
ON
ENG
ON
ON
English
Spanish
German
French
- - General Setup Page - -
Closed Caption
PreferenceDolby
General Audio
TV Display
TV Type
Angle Mark
OSD Lang
Captions
Screen Saver
PS
NTSC
ON
ENG
ON
ON
On
Off
- - General Setup Page - -
Screen Saver
PreferenceDolby
General Audio
TV Display
TV Type
Angle Mark
OSD Lang
Captions
Screen Saver
PS
NTSC
ON
ENG
ON
ON On
Off
- - Speaker Setup Page - -
Set Downmix Mode
PreferenceDolby
General
Downmix LT/RT
Stereo
Audio
Screen Saver
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select General.
3. Use the (,) Navigation buttons to move the cursor to the
Screen Saver item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between ON and OFF modes.
Note: If you turn the screen saver on, the screen saver image
appears when you leave the system in pause or stop
mode for more than 1 minute. The screen saver is useful
to prevent your display from becoming damaged.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
Downmix
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select Audio.
3. Use the (,) Navigation buttons to move the cursor to the
Downmix item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between LT/RT, Stereo modes.
LT/RT : The front speakers are in theatrical LT/RT downmix
mode.
Stereo: The front speakers are in Stereo Downmix mode.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM20
021
Dynamic
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select Dolby.
3. Use the (,) Navigation buttons to move the cursor to the
Dynamic item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between Full and off levels and
3/4 to 1/4 in between..
Note: Select your desired Dynamic Range Compression Rate
(DRC) to adjust linear compression rate to obtain the
different compression results of the signals.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
Audio
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select Preference.
3. Use the (,) Navigation buttons to move the cursor to the
Audio item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between English, French,
Spanish, German, and Japanese audio soundtrack
languages*.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
* Actual available audio languages depend on the disc used.
- - Dolby Digital - -Setup
Dynamic Range Compression
Preference
General
Dynamic
Audio Dolby
FULL
3/4
1/2
1/4
OFF
Subtitle
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select Preference.
3. Use the (,) Navigation buttons to move the cursor to the
Subtitle item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between English, French,
Spanish, German, or Japanese subtitles*. or turn subtitles
Off.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
* Actual available subtitle languages depend on the disc used.
Disc Menu
1. Press the SETUP button to enter the Setup Menu.
2. Use the (,) Navigation buttons to select Preference.
3. Use the (,) Navigation buttons to move the cursor to the
Disc Menu item.
4. Use the () Navigation button followed by the (,)
Navigation buttons to select between English, French,
Spanish, German, and Japanese Menu languages*.
5. Press the ENTER button.
6. Using the (,,,) Navigation buttons and press ENTER
to exit and save setting.
* Actual available menu languages depend on the disc used.
- - Preference Page - -
Preferred Audio Language
Dolby
General Audio
Audio
Subtitle
Disc Menu
ENG
ENG
ENG
English
French
Spanish
German
Japanese
Preference
- - Preference Page - -
Preferred Subtitle Language
Dolby
General Audio
Audio
Subtitle
Disc Menu
ENG
ENG
ENG
Off
English
French
Spanish
German
Japanese
Preference
- - Preference Page - -
Preferred Menu Language
Dolby
General Audio
Audio
Subtitle
Disc Menu
ENG
ENG
ENG English
French
Spanish
German
Japanese
Preference
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM21
22
Other Functions
This chapter describes how to use some functions contained in system.
ZOOM
1. Press the ZOOM button to change the size of the screen
between 2x, 3x, 4x, and off zoom.
Common Procedure
1. Press the DISPLAY button repeatedly during play to
display elapsed time of title, chapter, track, etc.
KEY LOCK
This feature allows you to lock all the controls on the front
panel of the main unit to prevent others, especially children,
from operating the unit without the remote handset. To
activate the Key Lock feature press the KEY LOCK
button on the remote control. The "Key Lock On" statement
will appear on the TV screen and all front panel controls,
including the Power button will be locked. To unlock the
front panel controls press the KEY LOCK button
on the remote control again. The "Key Lock Off" statement
will appear on the TV screen to indicate the unlock action.
Title Elapsed TT01/03 CH01/06
0:04:05
TT01/03 CH01/06
0:04:35
TT01/03 CH01/06
0:04:55
TT01/03 CH01/06
0:04:55
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM22
223
The disc does not play.
•Insert a disc.
•Insert the disc correctly with the playback side facing down
on the disc tray.
•Clean the disc. (see page 12)
•The system cannot play CD-ROMs, etc. (see page 11)
Insert a DVD or a CD disc.
•Check the region code of the DVD disc. (see page 11)
•Moisture has condensed inside the system. Remove the
disc and leave the system turned on for about an hour.
(see page 9)
The system starts playing the DVD automatically.
•The DVD features the auto playback function.
Playback stops automatically.
•Depending on the disc, the auto pause signal is recorded.
While playing such a disc, the system stops playback at the
signal.
Stopping playback, Search, Slow-motion play, repeat play
or Program play, etc., cannot be done.
•Depending on the disc, some of the above operations may
not be available.
Messages do not appear on the TV screen in the language
you want.
•Select the language for OSD in SETUP menu. (see page 20)
The disc must have the language you selected, if not, other
language will be selected.
The language for the sound cannot be changed when you
play a DVD.
•Multilingual sound is not recorded on the DVD.
•Changing the language for the sound is prohibited on the
DVD.
The language for the subtitles cannot be changed when
you play a DVD.
•Multilingual subtitles are not recorded on the DVD.
•Changing the language for the subtitles is prohibited on
the DVD.
The subtitles cannot be turned off when you play a DVD.
•Depending on the DVD, you may not be able to turn the
subtitles off.
The angles cannot be changed when you play a DVD.
•Multi-angles are not recorded on some DVDs.
•Change the angles when the angle marks appears on the
TV screen. (see page 17)
•Changing the angles is prohibited on some DVDs.
The system does not operate properly.
•Static electricity, etc., may affect the system’s operation.
Disconnect the AC power cord once, then connect it again.
Troubleshooting
If you experience any of the following difficulties while using the
system, use this troubleshooting guide to help you remedy the
problem. Should any problem persist, consult your nearest
service center by calling 1-800-898-9020.
No power.
•Is the power cord firmly plugged into the power outlet?
•One of the safety mechanisms may be operating. In this
event, unplug the player from the power outlet briefly and
then plug it in again.
No picture.
•Check that the system is connected securely.
•The video connecting cord is damaged. Replace it with a
new one.
•Make sure you connect the system to the video input
connector on the TV. (see page 14)
•Make sure you turn on the TV.
•Make sure you select the video input on the TV so that you
can view the pictures from this system.
Noise (interference) appears in the picture.
•Clean the disc.
•If video from this system has to go through your VCR to
get to your TV, the copy-protection applied to some DVD
programs could affect picture quality.
The aspect ratio of the screen cannot be changed even
though you set “TV SYSTEM” in the SETUP menu when
you play a wide picture.
•The aspect rate is fixed on your DVD disc.
•Depending on the TV, you may not be able to change the
aspect ratio.
There is no sound or only a very low-level sound is heard.
•The audio connecting cord is damaged. Replace it with a
new one.
•The system is in pause mode or in slow-motion play mode,
or fast forward or fast reverse is performed
•Press PLAY to return to normal play mode.
Severe hum or noise is heard.
•Move your TV away from the audio components.
•The plugs and jacks are dirty. Wipe them with a cloth slightly
moistened with alcohol.
•Clean the disc.
The remote does not function.
•Remove any obstacles between the remote control and
the system.
•Move the remote control closer to the system.
•Point the remote control at the remote sensor on the front
panel.
•Replace all the batteries in the remote control with new
ones if they are weak.
•Check that the batteries are loaded correctly.
Additional Information
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM23
24
The serial number of your system can be found on a label on the back panel of the
main unit, and also on the display carton. Please record the serial number in the
space below. You may need to refer to this number if your system ever needs to be
serviced.
Model No.: BAR330
Serial No.:
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM24
425
EMERSON RADIO CORP.
LIMITED WARRANTY
What does this warranty cover? Any manufacturing defects in original material, including original parts and
workmanship, under normal use and conditions.
For how long? For a period of ninety (90) days for labor and for a period of one (1) year for parts, from the date of original
purchase in the U.S.
What will we do? If you need service under this warranty, and you provide us with the dated proof of purchase, we will
provide repair service at no charge for labor and parts, for the time periods set forth above, at an authorized Depot Repair
Facility, or replace the product in our discretion.
How do you make your warranty claim? If it becomes necessary to repair your unit, you can obtain the name and mailing
location of a Depot Repair Facility by dialing 1-800-695-0098. You should pack your unit in a well-padded heavy
corrugated box, enclose your check or money order payable to the Depot Repair Facility in the amount of $9.00 to cover
the return shipping and handling costs, and enclose a copy of your proof of purchase (warranty service will not be
provided without a dated proof of purchase).
Finally, you should ship the unit prepaid via UPS or parcel post (insured).
What does your warranty not cover? Your warranty does not cover the following:
yDamage from negligence, misuse, abuse, accident, or failure to follow operating instructions.
yUse of product in a commercial application or rentals.
yChanges or repairs by anyone other than an authorized Depot Repair Facility.
yDamage because your unit is improperly connected to the equipment of other manufacturers.
yUnit on which the serial number has been defaced, modified or removed.
yDamage to equipment not properly connected to the product.
yCost incurred in shipping your unit to and from an authorized Depot Repair Facility.
yOrdinary adjustments which you can perform as outlined in the owner’s manual.
ySignal reception problems caused by external antenna or cable systems.
yProducts purchased, used, serviced, or damaged outside of the United States.
yDamage to compact discs or cassettes.
What other limitations apply to you warranty?
THIS WARRANTY IS NOT-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER AND DOES NOT
EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF
AMERICA. ANY APPLICABLE IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE
LIMITED IN DURATION TO A PERIOD OF THE EXPRESSED WARRANTY AS PROVIDED ABOVE BEGINNING WITH THE
DATE OF ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESSED OR IMPLIED, SHALL
APPLY TO THE PRODUCT THERE AFTER. WE MAKE NO WARRANTY AS TO THE FITNESS OF THE PROFDUCT FOR
ANY PARTICULAR PURPOSE OR USE.
THE EXTENT OF OUR LIABILITY UNDER THIS LIMITED WARRANTY IS THE REPAIR OR REPLACEMENT PROVIDED
ABOVE AND IN NO EVENT WILL OUR LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER OF THE
PRODUCT. UNDER NO CIRCUMSTANCES WILL WE BELIABLE FOR ANY LOSS, DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OF THIS PRODUCT.
How does state law apply to your warranty?
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, BUT YOU MAY ALSO HAVE OTHER RIGHT WHICH VARY
FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED WARRANTIES OR EXCLUSION
OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE, SO THESE RESTRICTIONS MAY NOT APPLY TO YOU.
DVD399
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM25
26
BAR330-020207-01 Printed in China
BARBIE BAR330_Eng P13-26.p65 2/2/2007, 3:30 PM26

Navigation menu