Empower Tribe Commercial FZE ULM200D01 USB Wireless Microphone Receiver User Manual ULM200M ULM200D Controls

MUSIC Group Services PH Corp USB Wireless Microphone Receiver ULM200M ULM200D Controls

Contents

Manual r1

ULM200M /ULM200D ControlsULM200M /ULM200D Controls1. POWER/STATUS LED1. ▼ VOLUME Button (Mute/volume down)2. ▲ VOLUME Button (Power on/unmute/volume up)3. USB connector5. Wireless Link Status LEDULM200M /ULM200D Getting Started1.Connect the ULM200D wireless receiver to the “WIRELESS ONLY!”USB connector onwireless-enabled BEHRIINGER mixers, powered speakers or other compatible products, or to aUSB port on a computer.2.Press and hold the ▲ button on the ULM200M wireless microphone to connect wirelessly to theULM200D receiver. The LED on the microphone will fl ash slowly during the connectingsequence and will light solid once connected. If the ULM200M wireless microphone cannotconnect to a receiver, the microphone will automatically power down after 10 seconds.3.Once connected, the ULM200M microphone will be set at a medium volume. Use the ▲ and ▼buttons to adjust the volume4. A long press of the ▼ button will put the ULM200M microphone into mute. The mutecondition is indicated by rapid fl ashing of the LED. If the user does not unmute within 60seconds, the ULM200M microphone will power down to save battery life.5. A short press of the ▲button will unmute the ULM200M microphone. If the ULM200Mmicrophone is unmuted more than 10 seconds after muting, it will return to the previous volumelevel, if unmuted after less than 10 seconds it will be set to the minimum volume level.6. Unplug the ULM200D wireless receiver to power down. The ULM200M wireless microphone
will power down 10 seconds after the ULM200D wireless receiver is unplugged.7. The LED in the ULM200M wireless microphone will indicate when the battery is low byregular brief fl ashes.8. Should the ULM200M wireless microphone become unpaired with the ULM200D wirelessreceiver, the microphone can be re-paired from the powered down state by simultaneouslypressing the ▲ and ▼ buttons and moving the microphone to within 10 cm (4 inches) of theULM200D wireless receiver. The LED on the microphone will fl ash slowly during the pairingsequence and will light solid once connected. If the ULM200M wireless microphone cannot pairto the receiver it will automatically power down after 10 seconds.SpecificationRF output <100 mW / +20 dBmOperating range 120 m (Line of Sight)*Dynamic range 92 dB, A-weighted**Equivalent input noise -112 dBuFrequency Response 20 Hz - 20 kHz, ±1 dB(Wireless Link)Sampling rate 48 kHzResolution 24-bitEncoding 232 kbps SLAC(Slightly Lossy Audio Codec)Latency 14.5 msRF frequency 2.4 GHz ISM band(2406 MHz - 2474 MHz)18 channelsPower Supply current 70 mA @ +5 VDCBattery type 2 x AA (LR6) Alkaline cellsBattery life >30 hoursDimensions (W x D x H) 45.7 x 45.7 x 243.8 mm(1.8 x 1.8 x 9.6")Weight 0.4 kg (0.9 lbs)*Achievable range will be dependent on nearby sources of RF interference and/or line of sightobstacles.**Measured from analog input to analog output, unity gain operation withoutLEGAL DISCLAIMERMUSICGroup accepts no liability for any loss which may be suff ered by any person who relies eitherwholly or in part upon any description, photograph, or statement contained herein. Technicalspecifi cations, appearances and other information are subject to change without notice. Alltrademarks are the property of their respective owners. MIDAS, KLARK TEKNIK,TURBOSOUND, BEHRINGER, BUGERA and DDA are trademarks or registered trademarks ofMUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2014 All rights reserved.LIMITED WARRANTYFor the applicable warranty terms and conditions and additional information regarding MUSIC
Group’s Limited Warranty, please see complete details online at music-group.com/warranty.FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATIONResponsible Party Name: MUSIC Group Services NV Inc.Address: 5270 Procyon Street Las Vegas, NV 89118 USAPhone Number: +1 702 800 8290ULTRALINK ULM200M/ULM202Dcomplies with the FCC rules as mentioned in the following paragraph:This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:•Reorient or relocate the receiving antenna•Increase the separation between the equipment and receiver•Connect the equipment into an outlet on a circuit diff erent from that to which the receiver isconnected•Consult the dealer or an experienced radio/TV technician for helpThis device complies with Part 15 of the FCC rules. Operation is subject to the following twoconditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may causeundesired operation.Important information:Changes or modifi cations to the equipment not expressly approved by MUSIC Group can voidthe user’s authority to use the equipment.Operation in the 2.4 GHz ISM (Industrial, Scientifi c, Medical) frequency band may be subject tointerference from other transmitting equipment operating in this band. In the event of suchinterference, please verify and reassign the transmitting channels of any potentially interferingtransmitting equipment.RF EXPOSURE (USB Receiver):The USB Receiver is intended to use exclusively with Behringer mobile host devices as indicatedin the user manual, it is not intended to connect to laptops or computers.A distance of 20 cm shall be maintained between the antenna and users, and the transmitter maynot be co-located with any other transmitter or antenna.

Navigation menu