EnGenius Technologies ECB350A 2.4G b/g/n AP User Manual ECB 9750

EnGenius Technologies 2.4G b/g/n AP ECB 9750

User Manual.pdf

Table of Contents

1 Introduction ....................................................................................................................................................................... 4

1.1 Features and Benefits ..................................................................................................................................................................................... 4

1.2 Package Contents ............................................................................................................................................................................................ 5

1.3 System Requirements ..................................................................................................................................................................................... 6

1.4 Applications ....................................................................................................................................................................................................... 6

2 Before you Begin ............................................................................................................................................................... 8

2.1 Considerations for Wireless Installation .................................................................................................................................................. 8

2.2 Computer Settings (Windows XP/Windows 7/Windows 8) .............................................................................................................. 9

2.3 Apple Mac X OS ............................................................................................................................................................................................. 13

2.4 Hardware Installation................................................................................................................................................................................... 14

3 Configuring Your Client Bridge ..................................................................................................................................... 16

3.1 Default Settings ............................................................................................................................................................................................. 16

3.2 Web Configuration ....................................................................................................................................................................................... 17

4 Building a Wireless Network ......................................................................................................................................... 19

4.1 Client Bridge Mode ...................................................................................................................................................................................... 19

4.2 Client Router Mode ...................................................................................................................................................................................... 20

4.3 Access Point Mode ....................................................................................................................................................................................... 21

4.4 Access Point Router Mode ........................................................................................................................................................................ 22

4.5 WDS AP / WDS Station Mode .................................................................................................................................................................. 23

4.6 WDS Bridge Mode ........................................................................................................................................................................................ 24

4.7 Repeater mode .............................................................................................................................................................................................. 25

5 Status ................................................................................................................................................................................ 26

5.1 Save/Reload .................................................................................................................................................................................................... 26

5.2 Main ................................................................................................................................................................................................................... 27

5.3 Connection Status......................................................................................................................................................................................... 29

5.4 Wireless Client List ........................................................................................................................................................................................ 30

5.5 System Log ...................................................................................................................................................................................................... 31

6 System .............................................................................................................................................................................. 32

6.1 Operation Mode ............................................................................................................................................................................................ 32

6.2 IP Settings ........................................................................................................................................................................................................ 33

6.3 Spanning Tree Setting ................................................................................................................................................................................. 34

7 Router ............................................................................................................................................................................... 36

7.1 WAN Settings ................................................................................................................................................................................................. 36

7.1.1 Static IP......................................................................................................................................................................................................... 36

7.1.2 DHCP ............................................................................................................................................................................................................. 39

7.1.3 PPPoE ............................................................................................................................................................................................................ 41

7.1.4 PPTP............................................................................................................................................................................................................... 43

7.2 LAN Settings ................................................................................................................................................................................................... 45

7.3 VPN Pass Through ........................................................................................................................................................................................ 46

7.4 Port Forwarding ............................................................................................................................................................................................. 47

7.5 Port Triggering ............................................................................................................................................................................................... 49

7.6 DMZ ................................................................................................................................................................................................................... 51

7.7 MAC Filter ........................................................................................................................................................................................................ 52

7.8 IP Filter .............................................................................................................................................................................................................. 53

7.9 URL Filter .......................................................................................................................................................................................................... 55

8 Wireless ............................................................................................................................................................................ 56

8.1 Wireless Network .......................................................................................................................................................................................... 56

8.2 Wireless Security ........................................................................................................................................................................................... 60

8.3 Site Survey ....................................................................................................................................................................................................... 63

8.4 Wireless MAC Filter ...................................................................................................................................................................................... 67

8.5 Wireless Advanced ....................................................................................................................................................................................... 68

8.6 WPS (Wi-Fi Protected Setup) .................................................................................................................................................................... 70

8.7 WDS Link Settings......................................................................................................................................................................................... 72

9 Management .................................................................................................................................................................... 74

9.1 Administration................................................................................................................................................................................................ 74

9.2 Management VLAN ...................................................................................................................................................................................... 75

9.3 SNMP Settings ............................................................................................................................................................................................... 76

9.4 Backup/Restore .............................................................................................................................................................................................. 78

9.5 Firmware Upgrade ........................................................................................................................................................................................ 79

9.6 Time Setting .................................................................................................................................................................................................... 80

9.7 Log ...................................................................................................................................................................................................................... 81

9.8 Diagnostics ...................................................................................................................................................................................................... 82

9.9 LED Control ..................................................................................................................................................................................................... 83

9.10 Logout ............................................................................................................................................................................................................... 84

9.11 Reset .................................................................................................................................................................................................................. 85

Appendix A – FCC Interference Statement .......................................................................................................................... 86

Appendix B – IC Interference Statement ............................................................................................................................. 87

Appendix C – CE Interference Statement ............................................................................................................................. 88

1 Introduction

The ECB350 is a multi-function 802.11b/g/n product with 8 major multi-functions. The ECB350 is designed to operate in

every working environment including enterprises.

The ECB350 is a Wireless Network device that delivers up to 6x faster speeds and 7x extended coverage than 802.11b/g

devices. The ECB350 supports use in the home network with superior throughput, performance, and significant wireless

range.

To protect data during wireless transmissions, the ECB350 encrypts all wireless transmissions through WEP data encryption

and supports WPA/WPA2 encryption. The ECB350 has MAC address filtering to allow users to select differing stations to

access the network. The ECB350 is an ideal product to ensure network safety for both home and enterprise environments.

1.1 Features and Benefits

Features

Benefits

High Speed Data Rate Up to 300 Mbps

Capable of handling heavy data payloads such as HD multimedia

streaming.

10/100/1000 Fast Ethernet

Support up to 1000Mbps networking speed.

IEEE 802.11n Draft Compliant and Backwards

Compatible with 802.11b/g devices

Fully compatible with IEEE 802.11b/g/n devices.

Multi-Function

Allowing users to select Access Point, Client Bridge, WDS AP, WDS

Bridge, WDS Station, Universal Repeater, Router or Client Router

mode in various applications.

Point-to-Point or Point-to-Multipoint

Wireless Connectivity

Allows transfer of data from building to building.

Support Multiple SSID in AP mode (up to 4)

Allow clients to access different networks through a single access

point and assign different policies and functions for each SSID

through the built in software.

WPA/WPA2/IEEE 802.1x Support

Powerful data security.

MAC Address Filtering in AP Mode

Ensure a secure network connection.

User Isolation Support (AP mode)

Protect the private network between client users.

Power-over-Ethernet (IEEE802.3af)

Flexible Access Point locations.

Save User Settings

Firmware upgrade does not delete user settings.

SNMP Remote Configuration Management

Allows remote connection to configure or manage the ECB350

easily.

QoS (WMM) support

Enhanced user performance and density.

1.2 Package Contents

The ECB350 package contains the following items (all items must be in package to issue a refund):

 ECB350 Wireless Long Range Multi-Function CB / AP

 12V/1A 100V~240V Power Adapter

 2*Detachable Antenna

 RJ-45 Ethernet LAN Cable

 CD-ROM with User's Manual

 Quick User Guide

1.3 System Requirements

The following are the minimum system requirements in order configure the device.

 Computer with an Ethernet interface or Wireless Network function

 Windows OS (XP, Vista, 7), Mac OS, or Linux based operating systems

 Web-Browsing Application (i.e.: Internet Explorer, FireFox, Safari, or other similar software)

1.4 Applications

Wireless LAN products are easy to install and highly efficient. The following list describes some of the many applications

made possible through the power and flexibility of wireless LANs:

a) Difficult-to-Wire Environments

There are many situations where wires cannot be laid easily or cannot be hidden from view. Older buildings, sites with

multiple buildings, and/or areas make the installation of a Wired LAN impossible, impractical, and/or expensive.

b) Temporary Workgroups

Create temporary workgroups/networks in open areas such as parks, athletic arenas, exhibition centers, temporary

offices, and construction sites where one wants a temporary Wireless LAN established and easily removed.

c) The Ability to Access Real-Time Information

Doctors/Nurses, Point-of-Sale Employees, and/or Warehouse Workers can access real-time information while dealing

with patients, serving customers, and/or processing information.

d) Frequently Changing Environments

Set up networks in environments that change frequently (i.e.: Show Rooms, Exhibits, etc.).

e) Small Office and Home Office (SOHO) Networks

SOHO users need a cost-effective, easy and quick installation of a small network.

f) Wireless Extensions to Ethernet Networks

Extend network coverage where the network cannot reach (i.e.: There is no wired internet connection to reach certain

location of the environment).

g) Wired LAN Backup

Implement wireless LANs to provide backup for mission-critical applications running on wired networks.

h) Training/Educational Facilities

Training sites at corporations or students at universities use wireless connectivity to ease access to information,

information exchanges, and learning.

2 Before you Begin

This section will guide you through the installation process. Placement of the ENGENIUS ECB350 is essential to maximize

the ECB350’s performance. Avoid placing the ECB350 in an enclosed space such as a closet, cabinet, or wardrobe.

2.1 Considerations for Wireless Installation

The operating distance of all wireless devices cannot be pre-determined due to a number of unknown obstacles in the

environment that the device is deployed in. These could be the number, thickness, and location of walls, ceilings, or other

objects that the ECB350’s wireless signals must pass through. Here are some key guidelines to allow the ECB350 to have

optimal wireless range.

 Keep the number of walls and/or ceilings between the ECB350 and other network devices to a minimum. Each wall

and/or ceiling can reduce the signal strength, resulting in lower signal strength.

 Building materials makes a difference. A solid metal door and/or aluminum stubs may have a significant negative

effect on the signal strength of the ECB350. Locate your wireless devices carefully so the signal can pass through a

drywall and/or open doorways. Materials such as glass, steel, metal, concrete, water (example: fish tanks), mirrors, file

cabinets and/or brick can also lower your wireless signal strength.

 Interferences can also come from your other electrical devices and/or appliances that generate RF noise. The most

usual types are microwaves, or cordless phones.

2.2 Computer Settings (Windows XP/Windows 7/Windows 8)

In order to use the ECB350, you must first configure the TCP/IPv4 connection of your computer system.

 Click Start button and open Control Panel.

Windows XP Windows 7

 Move your mouse to the lower right hot corner to display the Charms Bar and select the Control Panel in Windows 8

Windows 8

 In Windows XP, click Network Connections

 In Windows 7/Windows8, click View Network Status and Tasks in the Network and Internet section, then select

Change adapter settings

 Right click on Local Area Connection and select Properties

 Select “Internet Protocol Version 4 (TCP/IPv4)” and then

select Properties

 Select Use the following IP address and enter an IP address that is

different from the ECB350 and subnet mask then click OK.

Note: Ensure that the IP address and subnet mask are on the same subnet as

the device.

For example: ECB350 IP address: 192.168.1.1

PC IP address: 192.168.1.2 – 192.168.1.255

PC subnet mask: 255.255.255.0

2.3 Apple Mac X OS

 Go to System Preferences (can be opened in the Applications folder or selecting it in the Apple Menu)

 Select Network in the Internet & Network section

 Highlight Ethernet

 In Configure IPv4, select Manually

 Enter an IP address that is different from the ECB350 and subnet mask then press OK

Note: Ensure that the IP address and subnet mask are on the same subnet as the device.

For example: ECB350 IP address: 192.168.1.1

PC IP address: 192.168.1.2 – 192.168.1.255

PC subnet mask: 255.255.255.0

 Click Apply when done.

2.4 Hardware Installation

1. Ensure that the computer in use has an Ethernet Controller (RJ-45 Ethernet Port). For more information, verify with your

computer user manual.

2. Connect one end of the Category 5 Ethernet cable into the RJ-45 port of the ECB350 and the other end to the RJ-45

port of the computer that will use the ECB350. Ensure that the cable is securely connected to both the ECB350 and the

Computer.

3. Connect the Power Adaptor DC Inlet to the DC-IN port of the ECB350 and the Power Adaptor to the electrical outlet.

Once both connections are secure, verify the following:

a) Ensure that the POWER light is on (it will be green).

b) Ensure that the WLAN light is on (it will be green).

c) Ensure that the LAN (Computer/ECB350 Connection) light is on (it will be green).

d) Once all three lights are on, proceed to setting up the computer.

This diagram depicts the hardware configuration.

Front Panel Rear Panel

Front Panel

LED Lights

LED lights for Wireless, Ethernet port and Power.

Rear Panel

DC IN

DC IN for Power.

Reset Button

One click for reset the device. Press over 10 seconds for reset to factory default.

Ethernet Port

Ethernet port for RJ-45 cable.

3 Configuring Your Client Bridge

This section will show you how to configure the device using the web-based configuration interface.

3.1 Default Settings

Please use your Ethernet port or wireless network adapter to connect the Client Bridge.

Default Settings

IP Address

192.168.1.1

Username / Password

admin / admin

Operation Mode

Client Bridge

3.2 Web Configuration

 Open a web browser (Internet Explorer/Firefox/Safari) and enter the IP Address http://192.168.1.1

Note: If you have changed the default LAN IP Address of the Access Point, ensure you enter the correct IP Address.

 The default username and password are admin. Once you have entered the correct username and password, click the

 If successful, you will be logging in and see the ECB350 User Menu.

4 Building a Wireless Network

The ECB350 has the ability to operate in various operating modes. The ECB350 is the ideal device in which you can build

your WLAN. This chapter describes how to build a WLAN around your ECB350 using the operating modes of the ECB350.

4.1 Client Bridge Mode

In Client Bridge Mode, the ECB350 acts as a wireless dongle that connects to an Access Point to allow a system wireless

access to the network. This mode requires you to connect the Ethernet port on your PC to the ECB350 LAN port.

If you use the client bridge operating mode, use the ECB350 Site Survey feature to scan for Access Points within range.

When you find an Access Point, configure the ECB350 to use the same SSID and Security Password as the Access Point to

associate with it.

4.2 Client Router Mode

In the Client Router Mode, the ECB350 grants Internet access to multiple LANs. In this mode, the ECB350’s internal

Dynamic Host Configuration Protocol (DHCP) server automatically allocates ranges of IP addresses to each LAN that will

access the Internet through the ECB350.

This mode requires you to connect the ECB350 wirelessly to an Access Point or Wireless Router and then connect the LANs

to the ECB350 using a wired connection.

4.3 Access Point Mode

In Access Point Mode, ECB350 behaves likes a central connection for stations or clients that support IEEE 802.11b/g/n

networks. The stations and clients must be configured to use the same SSID and security password to associate with the

ECB350. The ECB350 supports up to four SSIDs at the same time for secure guest access.

4.4 Access Point Router Mode

In Access Point Router Mode, ECB350 grants Internet access to multiple wireless clients. In this mode, the ECB350’s internal

Dynamic Host Configuration Protocol (DHCP) server automatically allocates ranges of IP addresses to each wireless client

that will access the Internet through the ECB350.

This mode requires you to connect the ECB350’s Ethernet port to a modem or router. And the wireless clients must be

configured to use the same SSID and security password to associate with the ECB350. The ECB350 supports up to four

SSIDs at the same time for secure guest access.

4.5 WDS AP / WDS Station Mode

The ECB350 also supports WDS AP mode. This operating mode allows wireless connections to the ECB350 using WDS

technology. In this mode, configure the MAC addresses in both Access Points to enlarge the wireless area by enabling

WDS Link settings. WDS supports four AP MAC addresses.

Note: WDS Station Mode does not support Access Point feature.

4.6 WDS Bridge Mode

In WDS Bridge Mode, the ECB350 can wirelessly connect different LANs by configuring the MAC address and security

settings of each ECB350 device. Use this mode when two wired LANs located a small distance apart want to communicate

with each other. The best solution is to use the ECB350 to wirelessly connect two wired LANs, as shown in the following

figure.

WDS Bridge Mode can establish four WDS links, creating a star-like network.

Note: WDS Bridge Mode does not act as an Access Point. Access Points linked by WDS are using the same frequency channel. More Access

Points connected together may lower throughput. Please be aware to avoid loops in your wireless connection, otherwise enable Spanning

Tree Function.

4.7 Repeater mode

Repeater is used to regenerate or replicate signals that are weakened or distorted by transmission over long distances and

through areas with high levels of electromagnetic interference (EMI).

5 Status

The Status section contains the following options: Main, Wireless Client List, and System Log.

The following sections describe these options.

5.1 Save/Reload

This page lets you save and apply the settings shown under Unsaved changes list, or cancel the unsaved changes and

revert them to the previous settings that were in effect.

5.2 Main

Clicking the Main link under the Status menu or clicking Home at the top-right of the ECB350 Page shows the status

information about the current operating mode.

- The System Information section shows general system information such as Device Name, MAC Address, Current Time,

Firmware Version, and Management VLAN ID (Note: VLAN ID is only applicable in Access Point or WDS AP mode).

- The LAN Settings section shows the Local Area Network settings such as the LAN IP Address, Subnet Mask, and DNS

Address.

- The WAN Settings section shows WAN setting such as the MAC Address, Connection Type, Connection Status, IP

Address, Subnet Mask, and DNS Address.

Note: WAN Settings is only in Client Router and Router mode.

- The Current Wireless Settings section shows wireless information such as Operating Mode, Frequency, and Channel.

Since the ECB350 supports multiple-SSIDs, information about each SSID, the ESSID and security settings, are displayed

(Note: Profile Settings is only applicable in Access Point, WDS AP, or Router mode).

5.3 Connection Status

Click on the Connection Status link under the Status menu. This page displays the current status of the Network,

including Network Type, SSID, BSSID, Connection Status, Wireless Mode, Current Channel, Security, Data Rate, Noise Level,

and Signal Strength.

Note: Only applicable in Client Bridge, Client Router, WDS Station, and Repeater mode.

5.4 Wireless Client List

Clicking the Wireless Client List link under the Status menu displays the list of clients associated to the ECB350, along

with the MAC addresses and signal strength for each client. Clicking Refresh updates the client list.

Note: Only applicable in Access Point, WDS AP, Repeater and Router mode.

5.5 System Log

The ECB350 automatically logs (records) events of possible interest in its internal memory. To view the logged information,

click the System Log link under the Status menu. If there is not enough internal memory to log all events, older events are

deleted from the log. When powered down or rebooted, the log will be cleared.

System Log

Refresh

Update the log.

Clear

Clear the log.

6 System

6.1 Operation Mode

The ECB350 supports 8 operating modes: Access Point, Client Bridge, WDS AP, WDS Bridge, WDS Station, Universal

Repeater, Router, and Client Router.

System Properties

Device Name

Enter a name for the device. The name you type appears in SNMP management. This name is

not the SSID and is not broadcast to other devices.

Operation Mode

Use the radio button to select an operating mode.

Save & Apply / Cancel

Click Save & Apply to confirm the changes or Cancel to cancel and return previous settings.

6.2 IP Settings

This page allows you to modify the device's IP settings.

Note: Only applicable in Access Point, Client Bridge, WDS AP, WDS Bridge, WDS Station, and Repeater mode.

IP Settings

IP Network Setting

Select whether the device IP address will use the static IP address specified in the IP Address

field or be obtained automatically when the device connects to a DHCP server.

IP Address

The IP Address of this device.

IP Subnet Mask

The IP Subnet Mask of this device.

Default Gateway

The Default Gateway of this device. Leave it blank if you are unsure of this setting.

Primary / Secondary DNS

The primary / secondary DNS address for this device.

6.3 Spanning Tree Setting

This page allows you to modify the Spanning Tree settings. Enabling Spanning Tree protocol will prevent network loops in

your LAN network.

Note: Only in Access Point, Client Bridge, WDS AP, WDS Bridge, WDS Station, and Repeater mode.

Spanning Tree

Spanning Tree Status

Enable or disable the Spanning Tree function.

Bridge Hello Time

Specify Bridge Hello Time, in seconds. This value determines how often the device sends

handshake packets to communicate information about the topology throughout the entire

Bridged Local Area Network.

Bridge Max Age

Specify Bridge Max Age, in seconds. If another bridge in the spanning tree does not send a

hello packet for a long period of time, it is assumed to be dead.

Bridge Forward Delay

Specify Bridge Forward Delay, in seconds. Forwarding delay time is the time spent in each of

the Listening and Learning states before the Forwarding state is entered. This delay is provided

so that when a new bridge comes onto a busy network, it analyzes data traffic before

participating.

Priority

Specify the Priority Number. A smaller number has greater priority.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7 Router

This section is only applicable for AP Router Mode or Client Router Mode.

7.1 WAN Settings

There are four types of WAN connections: Static IP, DHCP, PPPoE, and PPTP. Please contact your ISP to find out which

settings you should choose.

7.1.1 Static IP

If your ISP Provider has assigned you a fixed IP address, enter the assigned IP Address, Subnet mask, Default Gateway IP

Address, and Primary DNS and Secondary DNS (if available) of your ISP provider.

Static IP

Internet Connection Type

Select Static IP to begin configuration of the Static IP connection.

Account Name

Enter the account name provided by your ISP.

Domain Name

Enter the domain name provided by your ISP.

MTU

Specify the Maximum Transmit Unit (MTU) size. It is recommended that you accept the default

setting of Auto. Otherwise, packets will be fragmented downstream if the MTU is set too high or

too low, which impacts network performance. In extreme cases, an MTU setting that is too low can

prevent the ECB350 from establishing some connections.

IP Address

Assign an IP address Manually.

IP Subnet Mask

Specify a subnet mask of the IP address.

Gateway IP Address

Specify the gateway of your network.

Primary DNS

Specify the primary DNS server’s IP address.

Secondary DNS

Specify the second DNS server’s IP address.

Discard Ping on WAN

Check to Enable to recognize pings on the ECB350 WAN interface or Disable to block pings on

the ECB350 WAN interface. Note: Pinging IP addresses is a common method used by hackers to

test whether the IP address is valid. Blocking pings provides some extra security from hackers.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

Note: Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see section 4.1).

7.1.2 DHCP

Select DHCP as your WAN connection type to obtain an IP address automatically. You will need to enter the account name

as your hostname and, optionally, enter DNS information.

DHCP

Internet Connection Type

Select DHCP to begin configuration of the DHCP connection.

Account Name

Enter the account name provided by your ISP.

Domain Name

Enter the domain name provided by your ISP.

MTU

Specify the Maximum Transmit Unit (MTU) size. It is recommended that you accept the default

setting of Auto. Otherwise, packets will be fragmented downstream if the MTU is set too high or

too low, which impacts network performance. In extreme cases, an MTU setting that is too low can

prevent the ECB350 from establishing some connections.

Get Automatically From

ISP

Click this radio button to obtain the DNS automatically from the DHCP server.

Use These DNS Servers

Click the radio button to set up the Primary DNS and Secondary DNS servers manually.

Discard Ping on WAN

Check to Enable to recognize pings on the ECB350 WAN interface or Disable to block pings on

the ECB350 WAN interface. Note: Pinging IP addresses is a common method used by hackers to

test whether the IP address is valid. Blocking pings provides extra security from hackers.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.1.3 PPPoE

Select Point-to-Point Protocol over Ethernet (PPPoE) if your ISP uses a PPPoE connection. Your ISP will provide you with a

username and password. This selection is typically used for DSL services. Remove your PPPoE software from your computer,

as it is not needed and will not work with your ECB350.

PPPoE

Internet Connection Type

Select PPPoE to begin configuration of the PPPoE connection.

MTU

Specify the Maximum Transmit Unit (MTU) size. It is recommended you accept the default

setting of Auto. Otherwise, packets will be fragmented downstream if the MTU is set too high

or too low, which impacts network performance. In extreme cases, an MTU setting that is too

low can prevent the ECB350 from establishing some connections.

Enter the Username provided by your ISP.

Password

Enter the Password provided by your ISP.

Service Name

Enter the Service Name provided by your ISP.

Connect on Demand

Select the radio button to specify the maximum idle time. Internet connection will disconnect

when it reach the maximum idle time, but it will automatically connect when user tries to access

the network.

Keep Alive

Select whether to keep the Internet connection always on, or enter a redial period once the

internet lose connection.

Get Automatically From ISP

Click this radio button to obtain the DNS automatically from the DHCP server.

Use These DNS Servers

Click the radio button to set up the Primary DNS and Secondary DNS servers manually.

Discard Ping on WAN

Check to Enable to recognize pings on the ECB350 WAN interface or Disable to block pings on

the ECB350 WAN interface. Note: Pinging IP addresses is a common method used by hackers to

test whether the IP address is valid. Blocking pings provides some extra security from hackers.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.1.4 PPTP

Select PPTP as your WAN connection type if your Internet Service Provider (ISP) uses a Point-to-Point Tunneling Protocol

(PPTP) connection. You will need to provide the IP address, Subnet Mask, Default Gateway (Optional), DNS (Optional),

Server IP, Username, and Password provided by your ISP.

PPTP

Internet Connection Type

Select PPTP to begin configuration of the PPTP connection.

MTU

Specify the Maximum Transmit Unit (MTU) size. It is recommended that you accept the default

setting of Auto. Otherwise, packets will be fragmented downstream if the MTU is set too high

or too low, which impacts network performance. In extreme cases, an MTU setting that is too

low can prevent the ECB350 from establishing some connections.

IP Address

Enter the WAN port IP address.

Subnet Mask

Enter the WAN IP subnet mask.

Default Gateway

Enter the WAN gateway IP address.

PPTP Server

Enter the IP address of the PPTP server.

Username

Enter the Username provided by your ISP.

Password

Enter the Password provided by your ISP.

Service Name

Enter the Service Name provided by your ISP.

Connect on Demand

Select the radio button to specify the maximum idle time. Internet connection will disconnect

when it reach the maximum idle time, but it will automatically connect when user tries to access

the network.

Keep Alive

Select whether to keep the Internet connection always on, or enter a redial period once the

internet loses connection.

Get Automatically From ISP

Click this radio button to obtain the DNS automatically from the DHCP server.

Use These DNS Servers

Click the radio button to set up the Primary DNS and Secondary DNS servers manually.

Discard Ping on WAN

Check to Enable to recognize pings on the ECB350 WAN interface or Disable to block pings on

the ECB350 WAN interface. Note: Pinging IP addresses is a common method used by hackers to

test whether the IP address is valid. Blocking pings provides some extra security from hackers.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.2 LAN Settings

This page allows you to modify the device's LAN settings.

LAN Settings

IP Address

The LAN IP Address of this device.

IP Subnet Mask

The LAN Subnet Mask of this device.

Use Router As DHCP Server

Check this option to enable the Internal DHCP server.

Starting /Ending IP Address

The range of IP addresses of the DHCP server will allocate to LAN device.

WINS Server IP

Enter the IP address of the WINS server.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.3 VPN Pass Through

The VPN Passthrough allows a secure virtual private network (VPN) connection between two computers. Enabling the

options on this page opens a VPN port and enables connections to pass through the ECB350 without interruption.

7.4 Port Forwarding

Port forwarding can be used to open a port or range of ports to a device on your network. Using port forwarding, you can

set up public services on your network. When users from the Internet make certain requests on your network, the ECB350

can forward those requests to computers equipped to handle the requests. For example, if you set the port number 80

(HTTP) to be forwarded to IP address 192.168.1.150, all HTTP requests from outside users are forwarded to 192.168.1.150.

Port Forwarding

Enables or disables the Port Forwarding feature.

Service Name

Enter a name or description to help you identify this entry.

Protocol

Select a protocol for the application. Choices are Both, TCP, and UDP.

Start / End Port

The port range that the server is running on the local computer.

IP Address

The local IP address of the computer the server is hosted on.

Add / Cancel

Click Add to add port forwarding rule or Cancel to discard the settings

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.5 Port Triggering

If you use Internet applications which use non-standard connections or port numbers, you may find that they do not

function correctly because they are blocked by the device’s firewall. Port Triggering will be required for these applications

to work.

Port Triggering

Enables or disables the Port Triggering feature.

Service Name

Enter a name or description to help you identify this entry.

Trigger Port

This is the outgoing (outbound) port numbers for this application.

Trigger Type

Select whether the application uses TCP, UDP or Both types of protocols for outbound transmissions.

Forwarded Port

These are the inbound (incoming) ports for this application.

Public Type

Select whether the application uses TCP, UDP or Both types of protocols for inbound transmissions.

Add / Cancel

Click Add to add port forwarding rule or Cancel to discard the settings

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.6 DMZ

If you have a computer that cannot run Internet applications properly from behind the ECB350, you can allow the

computer to have unrestricted Internet access. Enter the IP address of that computer as a Demilitarized Zone (DMZ) host

with unrestricted Internet access. Adding a client to the DMZ may expose that computer to a variety of security risks, so

use this option as a last resort.

DMZ

DMZ Hosting

Enables or disables the DMZ function.

DMZ Address

Enter an IP Address of the computer that will have unlimited Internet access.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

7.7 MAC Filter

You can choose whether to Deny or Allow only those devices listed in the MAC Filtering table to access the Internet.

MAC Filter

Enables or disables the MAC Filter function.

Deny all clients with MAC addresses

listed below to access the network

When selected, the computers listed in the MAC Filter Table will be Denied to access

the Internet.

Allow all clients with MAC addresses

listed below to access the network

When selected, only the computers listed in the MAC Filter table will be Allowed to

access the Internet.

7.8 IP Filter

You can choose whether to Deny or Allow only devices with those IP Addresses listed on the IP Filter Table from accessing

certain ports. This can be used to control which Internet applications the computers can access.

Note: You will need to have knowledge of which Internet port numbers each application uses.

IP Filter

Enables or disables the IP Filter function.

Deny all clients with IP addresses

listed below to access the network

When selected, the computers listed in the IP Filter table will be Denied to access

the Internet.

Allow all clients with IP addresses

listed below to access the network

When selected, only the computers listed in the IP Filter table will be Allowed to

access the Internet.

7.9 URL Filter

You can deny access to certain websites by blocking keywords in the URL web address.

For example, “gamer” has been added to the URL Filter Table. Any web address that includes “gamer” will be blocked.

8 Wireless

8.1 Wireless Network

This page displays the current status of the Wireless settings of the ECB350.

Access Point / WDS AP / Router mode:

Wireless Network (Access Point / WDS AP / Router mode)

Wireless Mode

Wireless mode supports 802.11b/g/n mixed mode.

Channel HT Mode

The default channel bandwidth is 20/40MHz. The larger the channel, the better the transmission

quality and speed.

Extension Channel

Select upper or lower channel. Your selection may affect the Auto channel function.

Channel / Frequency

Select the channel and frequency appropriate.

Auto

Check this option to enable auto-channel selection.

AP Detection

AP Detection can select the best channel to use by scanning nearby areas for Access Points.

Current Profile

Configure up to four different SSIDs. If many client devices will be accessing the network, you

can arrange the devices into SSID groups. Click Edit to configure the profile and check whether

you want to enable extra SSID.

Profile Isolation

Restricted client to communicate with different VID by selecting the radio button.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

SSID Profile

SSID

Specify the SSID for the current profile.

VLAN ID

Specify the VLAN tag for the current profile.

Suppressed SSID

Check this option to hide the SSID from clients. If checked, the SSID will not appear in the site

survey.

Station Separation

Click the appropriate radio button to allow or prevent communication between client devices.

Wireless Security

See the Wireless Security section.

Save / Cancel

Click Save to accept the changes or Cancel to cancel and return previous settings.

Client Bridge / Client Router / WDS Station / Repeater mode:

Wireless Mode

Wireless mode supports 802.11b/g/n mixed mode.

SSID

The SSID is a unique named shared amongst all the points of the wireless network. The SSID

must be identical on all points of the wireless network and cannot exceed 32 characters. You

may specify an SSID or select one from the Site Survey.

Site Survey

Click on Site Survey to search the existing Access Points.

Preferred BSSID

Specify the BSSID (Access Point’s MAC Address).

Wireless Security

The encryption is using. It must the same as Access Point’s encryption.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

8.2 Wireless Security

The Wireless Security section lets you configure the ECB350's security modes: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed,

WPA, WPA2, and WPA Mixed. We strongly recommend you use WPA2-PSK.

WEP Encryption:

WEP Encryption

Auth Type

Select Open System or Shared Key.

Input type

ASCII: Regular Text (recommended)

HEX: Hexadecimal Numbers (For advanced users)

Key Length

Select the desired option and ensure the wireless clients use the same setting.

Choices are 64, 128, 152-bit password lengths.

Default Key

Select the key you wish to be default. Transmitted data is ALWAYS encrypted using the Default

Key; the other Keys are for decryption only.

You must enter a Key Value for the Default Key.

Encryption Key #

Enter the key value or values you wish to use. Only the Key selected as Default is required. The

others are optional.

WPA-PSK (WPA Pre-Shared Key) Encryption:

WPA-PSK (WPA Pre-Shared Key) Encryption

Encryption

Select the WPA encryption type you would like.

Please ensure that your wireless clients use the same settings.

Passphrase

Wireless clients must use the same key to associate the device.

If using passphrase format, the Key must be from 8 to 63 characters in length.

Group Key Update Interval

Specify how often, in seconds, the group key changes.

WPA Encryption: Only in Access Point / WDS AP / Router mode

WPA Encryption

Encryption

Select the WPA encryption type you would like.

Please ensure that your wireless clients use the same settings.

Radius Server

Enter the IP address of the Radius Server.

Radius Port

Enter the port number used for connections to the Radius server.

Radius Secret

Enter the secret required to connect to the Radius server.

Group Key Update Interval

Specify how often, in seconds, the group key changes.

Note: 802.11n does not allow WEP/WPA-PSK TKIP/WPA2-PSK TKIP security mode. The connection mode will automatically change from

802.11n to 802.11g.

8.3 Site Survey

Use this feature to scan nearby Access Points.

Note: Only applicable in Client Bridge, Client Router, or Repeater modes.

1. Click Site Survey.

2. Scanning the nearby Access Points

3. The ECB350 will list the available access points after site survey.

Site Survey (Client Bridge / Client Router / Repeater mode)

BSSID

Access Point's wireless MAC address.

SSID

SSID that the Access Point is broadcasting.

Channel

Channel that the Access Point is using.

Signal Level (dBm)

Signal strength from the Access Point to your station.

Type

The band that the Access Point is using.

Security

Encryption method that the Access Point is using to secure data over the WLAN.

Refresh

Click Refresh to rescan nearby Access Point.

4. Select an Access Point and click that Access Point’s BSSID.

5. Enter the correct security setting.

8.4 Wireless MAC Filter

Wireless MAC Filters are used to allow or deny network access to wireless clients according to their MAC addresses. You

can manually add a MAC address to restrict the permission to access ECB350. The default setting is Disable Wireless MAC

Filter.

Note: Only applicable in Access Point, WDS AP, and Router mode.

Wireless Filter (Access Point / WDS AP / Router mode)

ACL Mode

Determines whether network access is granted or denied to clients whose MAC addresses

appear in the MAC Address table on this page. Choices are: Disabled, Deny MAC in the list, or

Allow MAC in the list.

MAC Address

Enter the MAC address of the wireless client.

Add

Click Add to add the MAC address to the MAC Address table.

Delete

Delete the selected entries.

Apply

Click Apply to apply the changes.

8.5 Wireless Advanced

This page allows you to configure wireless advance settings. It is recommended that the default settings are used unless

the user has experience with more advanced networking features.

Wireless Advanced

Data Rate

Select a data rate from the drop-down list. The data rate affects throughput of data in the ECB350.

The lower the data rate, the throughput will be lower, but so will the transmission distance.

Transmit Power

Set the power output of the wireless signal.

RTS/CTS Threshold

Specify the threshold package size for RTC/CTS. A small number causes RTS/CTS packets to be

sent more often and consumes more bandwidth.

Distance

Specify the distance between Access Points and clients. Longer distances may drop high-speed

connections.

Aggregation

Merges data packets into one packet. This option reduces the number of packets, but increases

packet sizes.

Wireless Traffic

Shaping

Check this option to enable wireless traffic shaping. Traffic shaping regulates the flow of packets

leaving an interface to deliver improved Quality of Service.

Incoming Traffic Limit

Specify the wireless transmission speed used for downloading.

Outgoing Traffic Limit

Specify the wireless transmission speed used for uploading.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

8.6 WPS (Wi-Fi Protected Setup)

Wi-Fi Protected Setup (WPS) feature is following the Wi-Fi Alliance WPS standard and it eases the set up of security-

enabled Wi-Fi networks in the home and small office environment.

It reduces the user steps required to configure a network and supports two methods that are familiar to most consumers

to configure a network and enable security.

Note: Only applicable in Access Point, WDS AP, and Router mode.

Wi-Fi Protected Setup (WPS)

WPS

Select to Enable or Disable the WPS feature.

WPS Current Status

Shows whether the WPS function is Configured or unConfigured.

When it is Configured, the WPS has been used to authorize connection between the device and

wireless clients.

Self Pin Code

The PIN code of this device.

SSID

The SSID (wireless network name) used when connecting using WPS.

Authentication Mode

Shows the encryption method used by the WPS process.

Passphrase Key

This is the passphrase key that is randomly generated during the WPS process. It is required if

wireless clients that do not support WPS attempts to connect to the wireless network.

WPS via Push Button

Click this button to initialize WPS feature using the push button method.

WPS via PIN

Enter the PIN code of the wireless device and click this button to initialize WPS feature using the

PIN method.

8.7 WDS Link Settings

Using WDS (Wireless Distribution System) will allow you to connect to Access Points wirelessly. Doing so will extend the

wired infrastructure to locations where cabling is not possible or inefficient to implement.

Note: Compatibility between different brands and models of access points is not guaranteed. It is recommended that the

WDS network be created using the same models for maximum compatibility.

Also note: All Access Points in the WDS network needs to use the same Channel and Security settings.

To create a WDS network, please enter the MAC addresses of the Access Points that you want included in the WDS. There can

be a maximum of four access points.

Note: Only applicable in WDS AP and WDS Bridge mode.

WDS Link Settings

MAC Address

Enter the Access Point’s MAC address to which you want to extend the wireless area.

Mode

Select Disable or Enable from the drop-down list.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

9 Management

9.1 Administration

This page allows you to change the ECB350 password as well as

configure the device by remote access. By default, the username is

admin and the password is: admin. The password can contain 0 to

12 alphanumeric characters and is case sensitive.

Note: Remote Access is only applicable in AP Router and Client Router mode.

Change Password

Name

Enter a new username for logging in to the New Name entry box.

Password

Enter a new password for logging in to the Password entry box.

Confirm Password

Re-enter the new password in the Confirm Password entry box for confirmation.

Save/Apply / Cancel

Click Save/Apply to apply the changes or Cancel to return previous settings.

Remote Access (only applicable in AP Router and Client Router mode)

Remote Management

Enable or Disable remote management.

Remote Upgrade

Specify whether the firmware of the ECB350 can be upgraded remotely.

Remote Management Port

If remote management is enabled, enter the port number to be used for remote management.

Example: If you specify the port number to 8080, enter http://<IP address>:8080 to access the

ECB350.

9.2 Management VLAN

This page allows you to assign a VLAN tag to the packets. A VLAN is a group of computers on a network whose software

has been configured so to behave as if they were on a separate Local Area Network (LAN). Computers on a VLAN do not

have to be physically located next to one another on the LAN.

Note: Only applicable in Access Point and WDS AP mode.

Management VLAN (Only applicable in Access Point mode)

Management VLAN ID

If your network includes VLANs, you can specify a VLAN ID for packets pass through the Access

Point with a tag. Otherwise, select No VLAN tag.

Accept / Cancel

Click Accept to confirm the changes or Cancel to cancel and return previous settings.

Note:

1. If you reconfigure the Management VLAN ID, you may lose your connection to the ECB350. Verify that the DHCP server supports the

reconfigured VLAN ID and then reconnect to the ECB350 using the new IP address.

2. Clicking Accept does not apply the changes. To apply them, use Status > Save/Load (see section 4.1).

9.3 SNMP Settings

This page allows you to assign the Contact Details, Location, Community Name, and Trap Settings for Simple Network

Management Protocol (SNMP). This is a networking management protocol used to monitor network attached devices.

SNMP allows messages (called protocol data units) to be sent to various parts of the network. Upon receiving these

messages, SNMP compatible devices (called agents) return the data stored in their Management Information Bases.

SNMP

SNMP Enable/Disable

Enable or Disable SNMP feature.

Contact

Specify the contact details of the device

Location

Specify the location of the device.

Community Name (Read

Only)

Specify the password for the SNMP community for read only access.

Community Name

(Read/Write)

Specify the password for the SNMP community with read/write access.

Trap

Trap Destination Address

Specify the IP address of the computer that will receive the SNMP traps.

Trap Destination

Community Name

Specify the password for the SNMP trap community.

9.4 Backup/Restore

This page allows you to save the current device configurations. When you save the configurations, you also can reload the

saved configurations into the device through the Restore Saved Settings from A File section. If extreme problems occur, or

if the you have set the ECB350 wrongly, you can use the Factory Default button in the Revert to Factory Default Settings

section to restore all the configurations of the ECB350 to the original default settings.

Backup/Restore

Save A Copy of Current

Settings

Click Backup to save the current configured settings.

Restore Saved Settings

from A File

To restore settings that have been previously backed up, click Browse, select the

file, and click Restore.

Revert to Factory Default

Settings

Click Factory Default button to restore the ECB350 to its factory default settings.

9.5 Firmware Upgrade

This page allows you to upgrade the firmware of the ECB350.

To perform the Firmware Upgrade:

1. Click the Browse button and navigate the OS File System to the location of the upgrade file.

2. Select the upgrade file. The name of the file will appear in the Upgrade File field.

3. Click the Upload button to commence the firmware upgrade.

Note: The device is unavailable during the upgrade process and must restart when the upgrade is completed. Any connections to or through the

device will be lost.

9.6 Time Setting

This page allows you to set the internal clock of the ECB350.

Time

Manually Set Date and Time

Manually specify the date and time.

Automatically Get Date and

Time

Select a time zone from the drop-down list and check whether you want to

enter the IP address of an NTP server or use the default NTP server to get have

the internal clock set automatically.

9.7 Log

This page allows you to setup Syslog and local log functions of the ECB350.

Log

Syslog

Enable or disable the syslog function.

Log Server IP Address

Enter the IP address of the log server.

Local Log

Enable or disable the local log service.

Save/Apply / Cancel

Click Save/Apply to apply the changes or Cancel to return previous settings.

9.8 Diagnostics

This page allows you to analyze the connection quality of the ECB350 and trace the routing table to a target in the

network.

Diagnosis

Target IP

Enter the IP address you would like to search.

Ping Packet Size

Enter the packet size of each ping.

Number of Pings

Enter the number of times you want to ping.

Start Ping

Click Start Ping to begin pinging target device (via IP).

Traceroute Target

Enter an IP address or domain name you want to trace.

Start Traceroute

Click Start Traceroute to begin the trace route operation.

9.9 LED Control

This page allows you to control LED for Power, LAN interface and WLAN interface of the ECB350.

9.10 Logout

Click Logout in the Management menu to logout of the ECB350 interface.

9.11 Reset

In some circumstances, it may be required to force the device to reboot. Click on Reboot the Device to reboot the ECB350.

Appendix A – FCC Interference Statement

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to

operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 21cm between the radiator & your body.

Appendix B – IC Interference Statement

Industry Canada statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet

aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,

y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 21cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit

être installé et utilisé avec un minimum de 21 cm de distance entre la source de rayonnement et votre corps.

Appendix C – CE Interference Statement

Europe – EU Declaration of Conformity

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet

aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,

y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 21cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit

être installé et utilisé avec un minimum de 21 cm de distance entre la source de rayonnement et votre corps.

0560

Česky

[Czech]

[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se

základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Dansk

[Danish]

Undertegnede [fabrikantens navn] erklæ rer herved, at følgende udstyr [udstyrets

typebetegnelse] overholder de væ sentlige krav og øvrige relevante krav i direktiv

1999/5/EF.

Deutsch

[German]

Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in

Ü bereinstimmung mit den grundlegenden Anforderungen und den übrigen

einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.

Eesti

[Estonian]

Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme

tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja

nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

English

Hereby, [name of manufacturer], declares that this [type of equipment] is in

compliance with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

Español

[Spanish]

Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]

cumple con los requisitos esenciales y cualesquiera otras disposiciones

aplicables o exigibles de la Directiva 1999/5/CE.

Ελληνική

[Greek]

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment]

ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ

ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

Français

[French]

Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est

conforme aux exigences essentielles et aux autres dispositions pertinentes de la

directive 1999/5/CE.

Italiano

[Italian]

Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è

conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla

direttiva 1999/5/CE.

Latviski

[Latvian]

Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of

equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un

citiem ar to saistītajiem noteikumiem.

Lietuvių

[Lithuanian]

Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius

reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.

Nederlands

[Dutch]

Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in

overeenstemming is met de essentiële eisen en de andere relevante bepalingen

van richtlijn 1999/5/EG.

Malti

[Maltese]

Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott]

jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm

fid-Dirrettiva 1999/5/EC.

Magyar

[Hungarian]

Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó

alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski

[Polish]

Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z

zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami

Dyrektywy 1999/5/EC.

Português

[Portuguese

]

[Nome do fabricante] declara que este [tipo de equipamento] está conforme com

os requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Slovensko

[Slovenian]

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in

ostalimi relevantnimi določili direktive 1999/5/ES.

Slovensky

[Slovak]

[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a

všetky príslušné ustanovenia Smernice 1999/5/ES.

Suomi

[Finnish]

[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen

tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten

ja sitä koskevien direktiivin muiden ehtojen mukainen.

Svenska

[Swedish]

Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med

de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av

direktiv 1999/5/EG.

EnGenius Technologies ECB350A 2.4G b/g/n AP User Manual ECB 9750

EnGenius Technologies 2.4G b/g/n AP ECB 9750

User Manual.pdf

Navigation menu

Namespaces

Views

Navigation