EnGenius Technologies ENH900EXTA Wireless Access Point User Manual
EnGenius Technologies Wireless Access Point
Contents
- 1. User Manual.pdf
- 2. User Manual_rev.pdf
User Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2247786 |
| Application ID | eJB64qP7dSqM/jH/6pHxhg== |
| Document Description | User Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 350.63kB (4382867 bits) |
| Date Submitted | 2014-04-22 00:00:00 |
| Date Available | 2014-04-22 00:00:00 |
| Creation Date | 2014-04-22 10:15:07 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2014-04-22 10:40:47 |
| Document Title | User Manual.pdf |
| Document Creator | Adobe InDesign CS6 (Windows) |
Business Solutions User Manual ENH900EXT version 1.0 Dual Band Long Range Wireless N900 Outdoor Access Point IMPORTANT To install this Access Point please refer to the Quick Installation Guide included in the product packaging. Table of Contents Chapter 1 Product Overview............................................... 4 Key Features/Introduction........................................................ 5 System Requirements............................................................... 6 Package Contents......................................................................... 7 Technical Specifications.............................................................. 8 Physical Interface.......................................................................... 10 2.4GHz/5 GHz SSID Profile...................................................... 41 Wireless Security.......................................................................... 42 Wireless MAC Filtering............................................................... 43 Wireless Advanced..................................................................... 44 WPS Mixed-Enterprise: AP/WDS AP Mode........................... 45 Fast Roaming................................................................................. 46 WDS Link Settings....................................................................... 47 2.4GHz Mesh Link Settings...................................................... 48 Guest Network Settings............................................................ 49 Chapter 2 Before You Begin................................................. 11 Computer Settings....................................................................... 12 Hardware Installation................................................................. 15 Mounting the ENH900EXT...................................................... 16 Chapter 8 Management ........................................................ 50 Management VLAN Settings.................................................. 51 Wi-Fi Multi Media......................................................................... 52 Advanced Settings....................................................................... 53 CLI Settings/Email Alert............................................................. 54 Time Zone........................................................................................ 56 Auto Reboot Settings................................................................ 57 Wi-Fi Scheduler............................................................................... 58 Tools.................................................................................................. 59 Account/Firmware........................................................................ 61 Backup/Restore ............................................................................. 62 Log...................................................................................................... 63 Logout/Reset................................................................................. 64 Appendix................................................................................. 65 FCC Interference Statement................................................... 66 CE Interference Statement...................................................... 67 Professional Installation Instruction ................................ 70 Chapter 3 Configuring Your Access Point......................... 18 Default Settings./Web Configuration................................ 19 Chapter 4 Building a Wireless Network........................... 20 Access Point Mode...................................................................... 21 WDS AP Mode.............................................................................. 23 WDS Bridge Mode........................................................................ 24 WDS Station Mode....................................................................... 25 AP Mesh Mode................................................................................ 26 Mesh Only Mode.......................................................................... 27 Chapter 5 Status.................................................................... 28 Main Status..................................................................................... 29 Connection...................................................................................... 32 Chapter 6 Network .............................................................. 34 Basic IP Settings............................................................................ 35 Spanning Tree Protocol Setting............................................. 36 Chapter 7 2.4 GHz/5 GHz Wireless....................................... 37 Wireless Settings............................................................................ 38 2.4 GHz/5 GHz Wireless Network........................................... 39 Chapter 1 Product Overview Introduction Key Features • Up to 29 dBm transmit power enabling long range connectivity • Supports IEEE802.11a/b/g/n wireless standards with up to 450 Mbps data rate on each band. • Three detachable 5 dBi 2.4 GHz Omni-directional antennas • Three detachable 7 dBi 5 GHz Omni-directional antennas • Mesh Supported • Can be used with included power adapter or via PoE with PoE 802.3at - capable switches or injectors • Dual Band/Three Stream • Band Steering shifts dual band clients to 5 GHz for better throughput performance • Secured Guest Network option available Introduction The ENH900EXT is a high-powered, long-range 3x3 DualBand Wireless 802.11a/b/g/n Outdoor Access Point with speeds up to 450 Mbps on both its high-powered 2.4 GHz and 5 GHz radios. It can be configured as an: Access Point, or WDS (AP, Station & Bridge). The ENH900EXT is designed to operate in a variety of outdoor environments. Its high-powered, long-range characteristics make it a costeffective alternative to ordinary Access Points that don’t have the range and reach to connect to a growing number of wireless users who wish to connect to a business network. The ENH900EXT supports the 2.4 GHz frequency band under 802.11 b/g/n mode while at the same time providing the 5 GHz band for communicating to and from other 5 GHz capable computers, tablets or smart phones or transferring files. Several ENH900EXTs can be deployed Maximum data rates are based on IEEE 802.11 standards. Actual throughput and range may vary depending on many factors including environmental conditions, distance between devices, radio interference in the operating environment, and mix of devices in the network. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their respective owners. For United States of America: Copyright © 2014 EnGenius Technologies, Inc. All rights reserved. System Requirements in a campus setting using the 5 GHz band as a backhaul to provide multiple 2.4 GHz wireless cells for computers or mobile devices in common outdoor areas. The following are the Minimum System Requirements in order to configure the device. The ENH900EXT is easy to install in virtually any location with its included PoE (Power over Ethernet) injector for quick outdoor installation. The ENH900EXT enables network administrators to control its transmit power and features settings for selecting narrow bandwidth and traffic shaping. The ENH900EXT also supports wireless encryption including Wi-Fi Protected Access (WPA-PSK/ WPA2-PSK) Encryption and IEEE 802.1X with RADIUS. • Computer with an Ethernet interface or wireless network capability • Windows OS (XP, Vista, 7), Mac OS, or Linux-based operating systems • Web-Browsing Application (i.e.: Internet Explorer, Firefox, Safari, or another similar browser application) Package Contents The ENH900EXT package contains the following items:* • ENH900EXT Access Point • 3 detachable 5 dBi 2.4 GHz Omni-directional Antenna • 3 detachable 7 dBi 5 GHz Omni-directional Antenna • Power Adapter (48V/0.8A) • PoE Injector (EPE-48GR) • Grounding Cable • Pole Mount Bracket • Wall Mount Base • Mounting Screw Set • Quick Installation Guide • Technical Support Card *(all items must be in package to issue a refund): Technical Specifications Standard: IEEE802.11a/n on 5 GHz IEEE802.11b/g/n on 2.4 GHz IEEE802.3at WDS Detail WDS AP WDS Bridge WDS Station Antenna 6 External N-type Antenna 3 x detachable 5 dBi 2.4 GHz Omni-directional Antennas 3 x detachable 7 dBi 5 GHz Omni-directional Antennas Mesh Detail Mesh AP Mesh Only Management Auto Channel Selection Multiple SSID: 16 SSIDs, 8 SSIDs per Radio BSSID SNMP V1/V2c/V3 MIB I/II, Private MIB VLAN Tag/VLAN Pass-through Clients Statistics Save Configuration as User Default Fast Roaming E-Mail Alert RADIUS Accounting Guest Network Physical Interface 2 x 10/100/1000 Gigabit Ethernet Port with PoE support LAN1 Port: IEEE802.3at PoE Input LAN2 Port: IEEE802.3af PoE Output Both Ethernet Ports support Surge Protection to 6KV LED Indicator Power LAN 1 LAN 2 2.4 GHz 5 GHz Power Requirements External Power Adapter, DC IN, 48V/0.8A IEEE802.3at support Control CLI Supported Distance Control (Ack Timeout) 802.1X Supplicant (CB Mode) Multicast Supported Auto Reboot Obey Regulatory Power Operation Modes Access Point WDS Mesh Security WEP Encryption - 64/128/152 bit WPA/WPA2 Personal (WPA-PSK using TKIP or AES) WPA/WPA2 Enterprise (WPA-PSK using TKIP or AES) Hides SSID in beacons MAC address filtering, up to 50 MACs Wireless STA (Client) connection list Https Support SSH Support RF Specification (Aggregated Value) Channel Data Rate Tx Power Rx Sensitivity 802.11b 2.4GHz 1Mbps 29 -96 2Mbps 29 -95 5.5Mbps 29 -93 11Mbps 29 -92 6Mbps 28 -94 54Mbps 25 -75 6Mbps 29 -94 54Mbps 24 -75 MCS0/ 8 / 16 29 -95 MCS7 / 15 / 23 24 -70 MCS0/ 8 / 16 22 -94 MCS7 / 15 / 23 22 -69 MCS0/ 8 / 16 27 -95 MCS7 / 15 / 23 23 -70 MCS0/ 8 / 16 27 -94 MCS7 / 15 / 23 23 -69 MCS0 MCS8 MCS0 MCS9 MCS0 MCS9 802.11g 2.4GHz 802.11a 5GHz QoS (Quality of Service) Complaint with IEEE 802.11e standard 802.11n HT20 2.4GHzx Physical/Environment Conditions Operating: Temperature: -4 °F to 158 °F (-20 °C to 70 °C) Humidity (non-condensing): 90% or less Storage: Temperature: -22 °F to 176 °F (-30 °C to 80 °C) Humidity (non-condensing): 90% or less 802.11n HT40 2.4GHz 802.11n HT20 5GHz 802.11n HT40 5GHz 802.11ac HT20 5GHz 802.11ac HT40 5GHz 802.11ac HT80 5GHz Physical Interface Dimensions and Weights Length: 11.22” Width: 8.58” Depth: 2.1” Weight: 4.17 lbs 1 2.4 GHz Antennas: Detachable 5 dBi 2.4 GHz Omni-directional 2 5 GHz Antennas Detachable 7 dBi 5 GHz Omni-directional 3 LAN Port 1 (802.3at PoE Input): Ethernet port for RJ-45 cable. 4 LAN Port 2 (802.3af PSE Output): Ethernet port for RJ-45 cable. 5 LED Indicators: LED lights for Power, LAN Port 1, LAN Port 2, 2.4 GHz Connection and 5 GHz Connection. 6 Ground 7 Mounting Holes: Using the provided hardware, the ENH900EXT can be attached to a wall or pole. 10 Chapter 2 Before You Begin 11 Computer Settings Windows XP/Windows 7 2b. In Windows 7, click View Network Status and Tasks in the Network and Internet section, then select Change adapter settings. In order to use the ENH900EXT, you must first configure the TCP/IPv4 connection of your Windows OS computer system. 1. Click the Start button and open the Control Panel. 3. Right click on Local Area Connection and select Properties. Windows XP Windows 7 2a. In Windows XP, click Network Connections. 12 4. Select Internet Protocol Version 4 (TCP/IPv4) and then select Properties. 5. Select Use the following IP address and enter an IP address that is different from the ENH900EXTand Subnet mask, then click OK. Note: Ensure that the IP address and Subnet mask are on the same subnet as the device. For example: ENH900EXT IP address: 192.168.1.1 PC IP address: 192.168.1.2 – 192.168.1.255 PC Subnet mask: 255.255.255.0 13 Apple Mac OS X 4. In Configure IPv4, select Manually. 1. Go to System Preferences (Which can be opened in the Applications folder or selecting it in the Apple Menu). 5. Enter an IP address that is different from the ENH900EXT and Subnet mask then press OK. 2. Select Network in the Internet & Network section. Note: Ensure that the IP address and Subnet mask are on the same subnet as the device. For example: ENH900EXT IP address: 192.168.1.1 PC IP address: 192.168.1.2 – 192.168.1.255 PC Subnet mask: 255.255.255.0 6. Click Apply when done. 3. Highlight Ethernet. 14 Hardware Installation 1. Connect one end of the Ethernet cable into the main LAN port (PoE) of the Access Point and the other end to the AP Ethernet port on the PoE injector. This diagram depicts the hardware configuration. 2. Connect the Power Adapter to the DC-IN port of the PoE injector and plug the other end in to an electrical outlet. 3. Connect the second Ethernet cable into the LAN port of the PoE injector and the other end to the Ethernet port on the computer. 4. Screw on the provided antennas to the device. Once both connections are secure, verify the following: PoE Injector/ PoE Swtich a) Ensure that the POWER light is on (it will be green). b) Ensure that the 2.4 GHz/5 GHz WLAN light is on (it will be green for both 5 GHz and 2.4 GHz). Ethernet c) Ensure that the LAN (Computer/ENH900EXT Connection) light is on (it will be green). Power Outlet PC d) Once all three lights are on, proceed to set up the Access Point using the computer. Note: The Access Point supports both IEEE 802.3at PoE (Power over Ethernet) or the included power injector. You may use either one as the power source. Do NOT use both at the same time. 15 Mounting the ENH900EXT Using the provided hardware, the ENH900EXT can be attached to a wall or a pole. To attach the ENH900EXT to a wall using wall mounting kit. 3. Place the lock and flat washers on the four hex cap screws and drive the screws to attach the bracket to the back of the Access Point. 1. Mark the four locations of the mounting holes on the flat mounting surface. 4. Tighten the flat washers to secure the bracket to the mounting surface. 2. Drill a 37 mm deep 8 mm hole in the markings and hammer the bolts into the openings. 3. 1. 2. 4. 16 To attach the ENH900EXT to a pole using the provided pole mounting kit: 1. Place the lock and flat washers on the four hex cap screws and drive the screws to attach the bracket to the back of the Access Point. 3. Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket . 4. Lock and tighten the Pole Strap to secure the Pole Mount Bracket to the pole. 2. Drive the four round head screws to attach the Pole Mount Bracket to the bracket. 1. Note: See diagram below for vertical and horizonal placements. 2. 3. horizontal placement horizontal placement 17 4. horizontal placement Chapter 3 Configuring Your Access Point 18 Configuring Your Access Point 2. The default username and password are admin. Once you have entered the correct username and password, click the Login button to open the web-base configuration page. This section will show you how to configure the device using the web-based configuration interface. Default Settings Please use your Ethernet port or wireless network adapter to connect the Access Point. IP Address 192.168.1.1 Username / Password admin / admin Web Configuration 1. Open a web browser (Internet Explorer/Firefox/Safari/ Chrome) and enter the IP Address http://192.168.1.1 3. If successful, you will be logged in and see the ENH900EXT User Menu. Note: If you have changed the default LAN IP Address of the Access Point, ensure you enter the correct IP Address. 19 Chapter 4 Building a Wireless Network 20 The ENH900EXT has the ability to operate in various modes. This chapter describes the operating modes of the ENH900EXT. Access Point Mode In Access Point Mode, ENH900EXT behaves likes a central connection for stations or clients that support IEEE 802.11a/b/g/n networks. The stations and clients must be configured to use the same SSID (Service Set Identifier) and security password to associate with the ENH900EXT. The ENH900EXT supports up to eight SSIDs per band at the same time for secure access. ENH900EXT Access Point Client 2.4 GHz Client 5 GHz Client Client Client Client 21 The ENH900EXT can be used as a centralized Outdoor Access Point with which other EnGenius Wireless N 2.4 or 5 GHz Outdoor Client Bridges can associate; leveraging the long-range capability of their internal high-gain directional antennas, resulting in a very cost-effective solution to expand a company network over a multiple building campus. ENH202 Client Bridge ENH202 Client Bridge ENH900EXT Access Point Client Client 2.4 GHz 2.4 GHz Client Client Client 5 GHz 5 GHz ENH500 Client Bridge ENH900EXT Client Bridge Switch Client Switch Internet Client Client Client 22 Client Client WDS AP Mode The ENH900EXT also supports WDS AP mode. This operating mode allows wireless connections to the ENH900EXT using WDS technology. In this mode, configure the MAC addresses in both Access Points to enlarge the wireless area by enabling WDS Link settings. WDS supports up to four (4) AP MAC addresses. ENH900EXT WDS AP ENH900EXT WDS AP 5 GHz 5 GHz Client Computer Client Computer 2.4 GHz Client 2.4 GHz Client Client 23 Client WDS Bridge Mode In WDS Bridge Mode, the ENH900EXT can wirelessly connect different LANs by configuring the MAC address and security settings of each ENH900EXT device. Use this mode when two wired LANs located a small distance apart want to communicate with each other. The best solution is to use the ENH900EXT to wirelessly connect two wired LANs, as shown in the following diagram. WDS Bridge Mode can establish up to four WDS links, creating a star-like network. Note: WDS Bridge Mode does not act as an Access Point. Access Points linked by WDS are using the same frequency channel. More Access Points connected together may lower throughput. This configuration can be susceptible to generate endless network loops in your network, so it is recommended to enable the Spanning Tree function to prevent this from happening. Client Computer ENH900EXT WDS Bridge ENH900EXT WDS Bridge Client Computer Client Computer ENH900EXT WDS Bridge 24 WDS Station Mode Station mode expands the WDS by receiving a wireless signal/service and sharing it through the Ethernet port. ENH900EXT WDS AP on both 5 GHz & 2.4 GHz ENH900EXT WDS Station ENH900EXT WDS Station ENH900EXT WDS Station 25 AP Mesh Mode Under the AP Mesh mode, the ENH900EXT can be used as the central connection hub for station or clients that support IEEE 802.11 b/g/n network. Under this mode, the ENH900EXT can be configured with the same Mesh SSID and security password in order to associate with other ENH900EXTs, as well as connect with clients under the same SSID and encryption signatures. For example, you would use one band to connect Access Points in range with Mesh mode and the other band to broadcast traffic on the network. Client Computer Client Computer Client Computer Client Computer Client Computer Client Computer ENH900EXT Access Point Client Computer Client Computer ENH900EXT Access Point ENH900EXT Access Point Client Computer Client Computer ENH900EXT Access Point Client Computer Client Computer Client Computer ENH900EXT Access Point ENH900EXT Access Point 26 Mesh Only Mode Under the Mesh-only mode, the ENH900EXT can be configured with the same Mesh SSID and security password in order to associate with other Mesh enabled ENH900EXTs, instead of connecting with clients. ENH900EXT Access Point ENH900EXT Access Point ENH900EXT Access Point ENH900EXT Access Point ENH900EXT Access Point ENH900EXT Access Point 27 Chapter 5 Status 28 Main Status Save Changes Device Status This page lets you save and apply the settings shown under Unsaved changes list, or cancel the unsaved changes and revert to the previous settings that were in effect. Clicking the Device Status link under the Overview menu shows the status information about the current operating mode. • The Device Information section shows general system information such as Device Name, MAC Address, Current Time, Firmware Version, and Management VLAN ID Note: VLAN ID is only applicable in Access Point or WDS AP mode. • The LAN Information section shows the Local Area 29 Network settings such as the LAN IP Address, Subnet mask, and DNS Address. • The Wireless LAN Information 2.4 GHz/5 GHz section shows wireless information such as Operating Mode, Frequency, and Channel. Since the ENH900EXT supports multiple-SSIDs, information about each SSID, the ESSID, and security settings, are displayed Note: Profile Settings are only applicable in Access Point and WDS AP modes. • The Statistics section shows Mac information such as SSID, MAC address, RX and TX. 30 • The Wireless Mesh Information - 2.4 GHz section shows wireless information such as Operation Mode, Wireless Mode, Channel Bandwidth, Frequency/ Channel, Mesh SSID and Mesh Security. 31 Connection 2.4 GHz/5 GHz Connection List 2.4 GHz/5 GHz WDS Link List Click the connection link under the Overview menu displays the connection list of clients associated to the ENH900EXT’s 2.4 GHz/5 GHz, along with the MAC addresses and signal strength for each client. Clicking Refresh updates the client list. Click the connection link under the Overview menu. This page displays the current status of the WDS link, including WDS Link ID, MAC Address, Link Status and RSSI. Note: Only applicable in WDS AP and WDS Bridge modes. Note: Only applicable in Access Point and WDS AP modes. 32 The Mesh Link List Monitor the 2.4GHz Mesh Link List under the status menu. The page will display the current status of the Mesh Links under the Mesh AP mode and Mesh nodes under the Mesh Only mode. Note: Only Applicable in the Mesh AP and Mesh Only mode. 33 Chapter 6 Network 34 Basic IP Settings IPv4/IPv6 Settings IP Network Settings: Select whether the device IP address will use a static IP address specified in the IP address field or be obtained automatically when the device connects to a DHCP server. This page allows you to modify the device’s IP settings. IP Address: The IP address of this device. Subnet Mask: The IP Subnet mask of this device. Gateway: The Default Gateway of this device. Leave it blank if you are unsure of this setting. Primary/Secondary DNS: The primary/secondary DNS address for this device. Save: Click Save to confirm the changes. 35 Spanning Tree Protocol (STP) Settings This page allows you to modify the Spanning Tree settings. Enabling the Spanning Tree protocol will prevent network loops in your LAN network. Spanning Tree Status: Enables or disables the Spanning Tree function. Hello Time: Specifies Bridge Hello Time in seconds. This value determines how often the device sends handshake packets to communicate information about the topology throughout the entire Bridged Local Area Network. Max Age: Specifies Bridge Max Age in seconds. If another bridge in the spanning tree does not send a hello packet for a long period of time, it is assumed to be inactive. Forward Delay: Specifies Bridge Forward Delay in seconds. Forwarding delay time is the time spent in each of the Listening and Learning states before the Forwarding state is entered. This delay is provided so that when a new bridge comes onto a busy network, it analyzes data traffic before participating in the network. Priority: Specifies the Priority Number. A smaller number has a greater priority than a larger number. Save: Click Save to confirm the changes. 36 Chapter 7 2.4 GHz & 5 GHz Wireless 37 Wireless Wireless Settings Device Name: Enter a name for the device. The name you type appears in SNMP management. This name is not the SSID and is not broadcast to other devices. Band Steering: Enable Band Steering to send 802.11n clients to the 5 GHz band, where 802.11b/g clients cannot go, and leave 802.11b/g clients in 2.4GHz to operate at their slower rates. Band Steering works within the Access Point by directing 5 GHz-capable clients to that band. Save: Click Save to confirm the changes. 38 This page displays the current status of the Wireless settings of the ENH900EXT. Extension Channel: Select upper or lower channel. Your selection may affect the Auto channel function. 2.4 GHz/5 GHz Wireless Network Transmit Power: Sets the power output of the wireless signal. Data Rate: Select a data rate from the drop-down list. The data rate affects throughput of data in the ENH900EXT. Select the best balance for you and your network but note that the lower the data rate, the lower the throughput, though transmission distance is also lowered. RTS/CTS Threshold: Specifies the threshold package size for RTC/CTS. A small number causes RTS/CTS packets to be sent more often and consumes more bandwidth. Client Limits: Limits the total number of clients. Operation Mode: Select Operation Mode. The ENH900EXT supports three different operation modes: Access Point, or WDS (WDS AP, WDS Bridge, and WDS Station). Aggregation: Merges data packets into one packet. This option reduces the number of packets, but also increases packet sizes. Wireless Mode: Supports 802.11b/g/n mixed mode in 2.4 GHz and 802.11a/n mixed mode in 5 GHz. AP Detection: AP Detection can select the best channel to use by scanning nearby areas for Access Points. Channel HT Mode: The default channel bandwidth is 20 MHz/ 40 MHz. The larger the channel, the greater the transmission quality and speed. Distance: Specifies the distance between Access Points and clients. Note that longer distances may drop higher- 39 speed connections. Save: Click Save to confirm the changes or Cancel to cancel and return to previous settings. 40 2.4 GHz/5 GHz SSID Profile Current Profile: You can configure up to sixteen (16) different SSIDs (eight (8) per band). If multiple client devices will be accessing the network, you can arrange the devices into SSID groups. Click Edit to configure the profile and check whether you want to enable extra SSID. SSID: Specifies the SSID for the current profile. Suppressed SSID: Check this option to hide the SSID from clients. If checked, the SSID will not appear in the site survey. Station Separation: Click the appropriate radio button to allow or prevent communication between client devices. VID: Specifies the VLAN tag for each profile. If your netowrk includes VLANs, you can specify a VLAN ID for packets pass through the Access Point with a tag. Wireless Security: See the Wireless Security section. Isolation: Restrict clients communicating with different VIDs by selecting the radio button. Save: Click Save to accept the changes. 41 Wireless Security Auth Type: Select Open System or Shared Key. The Wireless Security section lets you configure the ENH900EXT’s security modes: WEP, WPA-PSK, WPA2-PSK, WPA-PSK Mixed, WPA, WPA2, and WPA Mixed. It is strongly recommend that you use WPA2-PSK. Input Type: ASCII: Regular Text (recommended) Hexadecimal Numbers (For advanced users) Key Length: Select the desired option and ensure that wireless clients use the same setting. Your choices are 64, 128, and 152-bit password lengths. Default Key: Select the Key you wish to be the default. Transmitted data is ALWAYS encrypted using the Default Key; the other Keys are for decryption only. You must enter a Key Value for the Default Key. Encryption Key Number: Enter the Key Value or values you wish to use. Only the Key selected as Default is required. The others are optional. 42 Wireless MAC Filtering Wireless MAC Filtering is used to allow or deny network access to wireless clients (computers, tablet PCs, NAS, smartphones, etc.) according to their MAC addresses. You can manually add a MAC address to restrict permission to access the ENH900EXT. The default setting is: Disable Wireless MAC Filter. ACL Mode: Determines whether network access is granted or denied to clients whose MAC addresses appear in the MAC address table on this page. Your choices are: Disabled, Deny MAC in the list, or Allow MAC in the list. Note: Only applicable in Access Point and WDS AP modes. Add: Click Add to add the MAC address to the MAC address table. MAC Address: Enter the MAC address of the wireless client. Delete: Delete the selected entries. Save: Click Save to apply the changes. 43 Wireless Advanced WPA-PSK (WPA Pre-Shared Key) Encryption: Wireless Traffic Shaping Traffic shaping regulates the flow of packets leaving an interface to deliver improved Quality of Service. Encryption: Select the WPA encryption type you would like. Please ensure that your wireless clients use the same settings. Passphrase: Wireless clients must use the same Key to associate the device. If using ASCII format, the Key must be from 8 to 63 characters in length. If using HEX format, the Key must be 64 HEX characters in length. Enable Traffic Shaping: Check this option to enable Wireless Traffic Shaping. Download Limit: Specifies the wireless transmission speed used for downloading. Group Key Update Interval: Specifies how often, in seconds, the Group Key changes. Upload Limit: Specifies the wireless transmission speed used for uploading. Save: Click Save to confirm the changes. 44 WPA Mixed-Enterprise: Access Point / WDS AP mode Radius Accounting Server: Enter the IP address of the Radius accounting server. Radius Accounting Port Enter the port number used for connections to the Radius accounting server. Radius Accounting Secret: Enter the secret required to connect to the Radius accounting server. Interim Accounting Interval: Specifies how often, in seconds, the accounting data sends. Note: 802.11n does not allow WEP/WPA-PSK TKIP/ WPA2-PSK TKIP security mode. The connection mode will automatically change from 802.11n to 802.11g. Encryption: Select the WPA encryption type you would like. Please ensure that your wireless clients use the same settings. Radius Server: Enter the IP address of the Radius server. Radius Port: Enter the port number used for connections to the Radius server. Radius Secret: Enter the secret required to connect to the Radius server. Group Key Update Interval: Specifies how often, in seconds, the Group Key changes. Radius Accounting: Enable or disable accounting feature. 45 Fast Roaming Enable the function to serve mobile client devices that roam from Access Point to Access Point. Some applications running on Client devices require fast re-association when they roam to a different Access Point Please enter the settings of the SSID and initialize the Security mode to WPA enterprise, as well as to set the Radius Server firstly. Users can enable the Fast Roaming and implement the advanced search. Enable Fast Roaming: Enable or disable fast roaming feature. Enable Advanced Search: Enable or disable advanced search feature. Please also set the same enterprise Encryption under the same SSID on other Access Points and enable the Fast Roaming. When the configuration is realized on different Access Point, the mobile client devices can run the voice service and require seamless roaming to prevent delay in conversation from Access Point to Access Point. 46 WDS Link Settings 2.4 GHz/5 GHz WDS Link Settings Using the WDS (Wireless Distribution System) feature will allow a network administrator or installer to connect to Access Points wirelessly. Doing so will extend the wired infrastructure to locations where cabling is not possible or inefficient to implement. Note: Compatibility between different brands and models of Access Points is not guaranteed. It is recommended that the WDS network be created using the same models for maximum compatibility. Also note: All Access Points in the WDS network need to use the same Channel and Security settings. Security: Select None or AES from the drop-down list. To create a WDS network, please enter the MAC addresses of the Access Points that you want included in the WDS. There can be a maximum of four Access Points. AES Passphrase: Enter the Key Values you wish to use. Other Access Points must use the same Key to establish a WDS link. Note: Only applicable in WDS AP and WDS Bridge modes. MAC Address: Enter the Access Point’s MAC address to where you want to extend the wireless area. Mode: Select to disable or enable from the drop-down list. Save: Click Save to confirm the changes. 47 2.4GHz Mesh Link Settings AES Passphrase: Enter the key values you wish to uses. Other Access Points must use the same key to establish a mesh link Users can choose the 2.4GHz band for Mesh operation. Mesh Settings Mesh SSID: To create a mesh network, please enter the Mesh SSID of the Access Point that you wish to include in the Mesh. Security: Select None or WPA2-PSK AES from drop-down list. 48 Guest Network Settings Ending IP Address: The last IP Address in the range of addresses assigned by the DHCP server. Adding a guest network allows visitors to use the Internet without giving out your office or company wireless security key. You can add a guest network to each wireless network in the 2.4 GHzb/g/n and 5 GHza/n frequencies. Fast Handover Fast Handover: Enable the Fast Handover feature by ensuring that each client is served by at least one Access Point at any time. Access Points continuously monitor the connectivity quality of any client in their range and efficiently share this information with other Access Points in the vincinity of that client to coordinate which of them should serve the client best. SSID: Specifies the SSID for the current profile. Suppressed SSID: Check this option to hide the SSID from clients. If checked, the SSID will not appear in the site survey. RSSI: Enter the RSSI (Received Signal Strength Index) in order to determine the handover procedure which the current wireless link will terminate. RSSI is an indication of the power level being received by the antenna. Therefore, the higher the RSSI number, the stronger the signal. Station Separation: Click the appropriate radio button to allow or prevent communication between client devices. IP Address: The IP Address of this device. Subnet Mask: The IP Subnet mask of this device. Starting IP Address: The first IP Address in the range of the addresses by the DHCP server. 49 Chapter 8 Management 50 Management VLAN Settings Management VLAN: If your network includes VLANs, you can enable Management VLAN ID for packets passing through the Access Point with a tag. This page allows you to assign a VLAN tag to packets sent over the network. A VLAN is a group of computers on a network whose software has been configured so that they behave as if they were on a separate Local Area Network (LAN). Computers on VLAN do not have to be physically located next to one another on the LAN. Save: Click Save to confirm the changes or Cancel to cancel and return to previous settings. Note: If you reconfigure the Management VLAN ID, you Note: Only applicable in Access Point and WDS AP modes. may lose your connection to the ENH900EXT. Verify that the DHCP server supports the reconfigured VLAN ID and then reconnect to the ENH900EXT using the new IP address. 51 Wi-Fi Multi Media (WMM) Class (AC) over the other, such as giving voice or video priority over email. This feature provide QoS (Quality of Service) for prioritizing multimedia traffic on the network. WMM prioritization achieves the goal of minimizing delay in a wireless network for time-sensitive applications such as video streaming. WMM Parameters: According to version 1.1 of the WMM specifications by the Wi-Fi Alliance, defines four Access Category (AC_BE, AC_BK, AC_VI, AC_VO) labels in order to provide more favorable network access for applications that are less tolerant of packet delays. CW: CW (Contention Window) maintains the DCF random back-off component to help avoid collisions of packets from the same access category. AIFS: Arbitration Inter-Frame Spacing (AIFS) in wireless LAN communications is a method of prioritizing one Access 52 Advanced Settings SNMP Settings Location: Specifies the location of the device. This page allows you to assign the Contact Details, Location, Community Name, and Trap Settings for a Simple Network Management Protocol (SNMP). SNMP is a networking management protocol used to monitor network attached devices. SNMP allows messages (called protocol data units) to be sent to various parts of the network. Upon receiving these messages, SNMP compatible devices (called agents) returns the data stored in their Management Information Bases. Community Name (Read Only): Specifies the password for the SNMP community for read only access. Community Name (Read/Write): Specifies the password for the SNMP community with read/write access. Trap Destination Address: Specifies the IP address of the computer that will receive the SNMP traps. Trap Destination Community Name: Specifies the password for the SNMP trap community. SNMPv3: Enables or disables the SNMPv3 feature. User Name: Specifies the username for SNMPv3. Auth Protocol: Selects the authentication protocol type: MDS or SHA. Auth Key: Specifies the authentication key. Priv Protocol: Selects the privacy protocol type: DES. Priv Key: Specifies the privacy key for privacy. Engine ID: Specifies the engine ID for SNMPv3. SNMP Enable/Disable: Enables or disables the SNMP feature. Apply Save: Click Apply Save to apply the changes. Contact: Specifies the contact details of the device. 53 CLI Settings Email Alert You can use the Email Alert feature to send messages to the configured email address when particular system events occur. Note: Do NOT use your personal email address as it can unnecessarily expose your personal email login credentials. Use a separate email account made for this feature instead CLI: The Command Line Interface (CLI) allows you to type commands instead of choosing them from a menu or selecting an icon. SSH: Enable Secure Shell (SSH) to make secure, encrypted connections in the network. Secure Shell is a network protocol that allows data to be exchanged using a secure channel between two network devices. HTTPS: Enable HTTPS to transfer and display web content securely. The Hypertext Transfer Protocol over SSL (Secure Socket Layer) is a TCP/IP protocol used by web servers to transfer and display web content securely. From: Enter the email address to show the sender of the email. To: Enter the address to receive email alerts. Subject: Enter the text to appear in the email subject line. 54 Username: Enter the username for the email account that will be used to send emails. Password: Enter the password for the email account that will be used to send emails. SMTP Server: Enter the IP address or hostname of the outgoing SMTP server. Port: Enter the SMTP port number to use for outbound emails. 55 Time Zone Time Setting Start: Select the day, month, and time when daylight savings time starts. This page allows you to set the internal clock of the ENH900EXT. End: Select the day, month, and time when daylight savings times ends. Manually Set Date and Time: Manually specify the date and time. Automatically Get Date and Time: Select Automatically Get Date and Time and check whether you wish to enter the IP address of an NTP server or use the default NTP server to have the internal clock set automatically. Enable Daylight Saving: Check whether daylight savings applies to your area. 56 Auto Reboot Settings You can specify how often you wish to reboot the ENH900EXT. Auto Reboot Setting: Enables or disables the Auto Reboot function. Frequency of Auto Reboot: Specifies how often you wish to reboot the ENH900EXT by Min, Hour, Day or Week. Timer: Select the day and enter the time you would like to reboot automatically. Save: Click Save to apply the changes. 57 Wi-Fi Scheduler drop-down list. The Wi-Fi Scheduler can be created for use in enforcing rules. For example, if you wish to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu and Fri while entering a Start time of 3pm and End Time of 8pm to limit access to these times. Day(s): Place a checkmark in the boxes for the desired days or select the All Week radio button to select all seven days of the week. Duration: The Start Time is entered in two fields. The first box is for hours and the second box is for minutes. The End Time is entered in the same format as the Start time. Status: Enables or disables the Wi-Fi scheduler function. Wireless Radio: Select 2.4 GHz or 5 GHz from the dropdown list for the preferred band type. SSID Selection: Select a SSID from the drop-down list. Schedule Templates: Select a schedule template from the 58 Tools Ping Test Parameters Start Ping: Click Start Ping to begin pinging the target device (via IP). This page allows you to analyze the connection quality of the ENH900EXT and trace the routing table to a target in the network. Traceroute Target: Enter the IP address or domain name you wish to trace. Start Traceroute: Click Start Traceroute to begin the trace route operation. Target IP: Enter the IP address you would like to search. Ping Packet Size: Enter the packet size of each ping. Number of Pings: Enter the number of times you wish to ping. 59 Speed Test Parameters / LED Control LED Control This page allows you to control LED on/off for Power, LAN interface, or 2.4 GHz/5 GHz WLAN interface. Power: Enables or disables the Power LED indicator. LAN: Enables or disables the LAN LED indicator. WLAN-2.4 GHz: Enables or disables the WLAN-2.4 GHz LED indicator. WLAN-5 GHz: Enables or disables the WLAN-5 GHz LED indicator. Device Discovery This page allows you to discover devices from network for Operation Mode, IP Address, System MAC Address and Firmware version. 60 Account Firmware This page allows you to change the ENH900EXT username and password. By default, the username is: admin and the password is: admin. The password can contain from 0 to 12 alphanumeric characters and is case sensitive. Firmware Upgrade This page allows you to upgrade the firmware of the ENH900EXT. Account Settings To Perform the Firmware Upgrade: 1. Click the Choose File button and navigate the OS file system to the location of the upgrade file. Administrator Username: Enter a new username for logging in to the New Name entry box. 2. Select the upgrade file. The name of the file will appear in the Upgrade File field. Current Password: Enter the old password for logging in to the Old Password entry box. 3. Click the Upload button to commence the firmware upgrade. New Password: Enter the new password for logging in to the New Password entry box. Note: The device is unavailable during the Firmware upgrade process and must restart when the upgrade is completed. Any connections to or through the device will be lost. Verify Password: Re-enter the new password in the Confirm Password entry box for confirmation. Apply: Click Apply to apply the changes. 61 Backup/Restore Backup Setting: Click Export to save the current configured settings. This page allows you to save the current device configurations. When you save your configurations, you also can reload the saved configurations into the device through the Restore Saved Settings from a file section. If extreme problems occur, or if you have set the ENH900EXT incorrectly, you can use the Reset button in the Revert to Factory Default Settings section to restore all the configurations of the ENH900EXT to the original default settings. Restore New Setting: To restore settings that have been previously backed up, click Browse, select the file, and click Restore. Restore to Default: Click Reset button to restore the ENH900EXT to its factory default settings. 62 Log System Log Remote Log The ENH900EXT automatically logs (records) events of possible interest in its internal memory. To view the logged information, click the Log link under the System Manager menu. If there is not enough internal memory to log all events, older events are deleted from the log. When powered down or rebooted, the log will be cleared. This page allows you to setup the Remote Log functions for the ENH900EXT. Syslog: Enables or disables the syslog function. Log Server IP Address: Enter the IP address of the log server. Remote Log: Enable or disable the remote log service. Apply: Click Apply to apply the changes. 63 Logout Reset Click Logout in Management menu to logout. In some circumstances, it may be required to force the device to reboot. Click on Reset to reboot the ENH900EXT. 64 Appendix 65 Appendix A Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 38 cm between the radiator & your body. 66 Appendix B - CE Interference Statement Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: • EN60950-1 Safety of Information Technology Equipment • EN50385 Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz) • EN 300 328 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive • EN 301 893 Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2 of the R&TTE Directive • EN 301 489-1 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements • EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment 67 This device is a 5GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ. 68 Français [French] Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/ 5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. 69 Appendix C - Professional Installation Instruction Installation Personal This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting. Installation Location The product shall be installed at a location where the radiating antenna can be kept 38cm from nearby person in normal operation condition to meet regulatory RF exposure requirement. External Antenna Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is prohibited. Installation Procedure Please refer to user’s manual for the detail. Warning: Please carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalty. 70 Instructions d’installation professionnelle Installation Ce produit est destine a un usage specifique et doit etre installe par un personnel qualifie maitrisant les radiofrequences et les regles s’y rapportant. L’installation et les reglages ne doivent pas etre modifies par l’utilisateur final. Emplacement d’installation En usage normal, afin de respecter les exigences reglementaires concernant l’exposition aux radiofrequences, ce produit doit etre installe de facon a respecter une distance de 38cm entre l’antenne emettrice et les personnes. Antenn externe Utiliser uniiquement les antennes approuvees par le fabricant. L’utilisation d’autres antennes peut conduire a un niveau de rayonnement essentiel ou non essentiel depassant les niveaux limites definis par FCC/IC, ce qui est interdit. Procedure d’installation Consulter le manuel d’utilisation. Avertissement: Choisir avec soin la position d’installation et s’assurer que la puissance de sortie ne depasse pas les limites en vigueur. La violation de cette regle peut conduire a de serieuses penalites federales. 71
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Annotate, Fill forms XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Create Date : 2014:04:22 10:15:07+08:00 Metadata Date : 2014:04:22 10:40:47+08:00 Modify Date : 2014:04:22 10:40:47+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:b1b8dce5-ac1c-4a71-ada0-8950743f180c Original Document ID : xmp.did:C4416EC81C206811822AF00EF18081D8 Document ID : xmp.id:7DAD67E3C3C9E311BDA58623F4E1A46E Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:7CAD67E3C3C9E311BDA58623F4E1A46E Derived From Document ID : xmp.did:DF6F5D372BC9E31196F29FB1F253631C Derived From Original Document ID: xmp.did:C4416EC81C206811822AF00EF18081D8 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:04:22 10:15:07+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Has XFA : No Page Count : 71 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools