EnGenius Technologies ESR1200 Dual Band Wireless AC1200 Router User Manual

EnGenius Technologies Dual Band Wireless AC1200 Router

User Manual.pdf

Download:
Mirror Download [FCC.gov]
Document ID	2121263
Application ID	p53E2+zA38UxHKauyv0RRQ==
Document Description	User Manual.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	302.03kB (3775388 bits)
Date Submitted	2013-11-18 00:00:00
Date Available	2013-11-18 00:00:00
Creation Date	2013-11-14 10:56:51
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2013-11-18 09:47:58
Document Title	User Manual.pdf
Document Creator	Adobe InDesign CS6 (Macintosh)

quantum beam
User Manual
ESR1200
version 1.0
Dual Band Wireless ACI200 Router
with Gigabit Ports and USB
IMPORTANT
To install this router, please refer to the Quick Start Guide
included in the product packaging.
To activate and use EnShare™ refer to the document
“Using EnShare” also in the product packaging.
Table of Contents
Chapter 1 Product Overview..............................................................5
Key Features....................................................................................................6
Technical Specifications/Software Features.....................................8
Physical Interface..........................................................................................9
Chapter 4 Basic Network Settings.................................................35
Network Settings.......................................................................................36
Status.............................................................................................................37
WAN Settings...............................................................................................38
LAN Settings................................................................................................39
WLAN Settings............................................................................................40
Guest Network............................................................................................41
Configuring the LAN (Local Area Network).....................................42
DHCP Server.................................................................................................43
Configuring Dynamic Host Configuration Protocol.......................44
Enable Static DHCP IP..............................................................................45
Current Static DHCP Table......................................................................46
Configuring Event Logging.....................................................................47
Monitoring Bandwidth Usage................................................................48
Configuring the System Language.....................................................49
Configuring IP Cameras............................................................................50
Configuring Internet Settings...............................................................51
Configuring Dynamic IP...........................................................................52
DNS Servers..................................................................................................53
Configuring Static IP.................................................................................54
Configuring PPPoE.....................................................................................55
Configuring PPTP.......................................................................................56
PPTP Settings..............................................................................................57
Configuring L2TP.......................................................................................58
L2TP Settings..............................................................................................59
Configuring DS-Lite...................................................................................60
Wireless LAN Setup...................................................................................61
Access Point Mode....................................................................................62
Wireless Distribution System Mode....................................................63
WDS Security Settings Screen...............................................................64
Chapter 2 Controlling the Router Through Its
Web Configuration Interface...........................................................10
Logging In.....................................................................................................11
Viewing the Web Configuration Dash Board..................................12
Home Page...................................................................................................13
Web Menus Overview...............................................................................14
Internet.................................................................................................15
Wireless 2.4 GHz..........................................................................................16
Wireless 5 GHz...............................................................................................17
Parental Controls........................................................................................18
Guest Network.............................................................................................19
IPv6.....................................................................................20
Firewall...................................................................................21
VPN.....................................................................................22
USB Port..........................................................................................................23
Advanced.......................................................................................................24
Tools................................................................................................................26
Chapter 3 Installation Setup Wizard..............................................27
Internet Setup Wizard...............................................................................28
Setting Up Your Internet Connection.................................................29
Setting Your Wireless Security..............................................................30
Setting your Router’s Administrator Password.............................31
Setting your Router’s Time Zone........................................................32
Status and Save Settings.......................................................................34
Chapter 5 Wireless Encryption.......................................................65
Wi-Fi Protect Access (WPA) Pre-Shared Key..................................66
Configuring Security.................................................................................67
Encryption Type.........................................................................................68
WPA Radius..................................................................................................69
Wired Equivalent Privacy (WEP)...........................................................70
Configuring Filters......................................................................................71
MAC Address Filtering Table.................................................................72
Configuring Wi-Fi Protected Setup....................................................73
Configuring Client List.............................................................................74
Network.......................................................................................................103
Advanced.....................................................................................................104
Configuring a User Setting...................................................................105
USB Port/Enshare....................................................................................106
Viewing File Server.................................................................................107
Viewing DLNA...........................................................................................108
Advanced Network Settings................................................................109
Port Mapping Setup................................................................................110
Current Port Mapping Table................................................................111
Port Forwarding Setup...........................................................................112
Current Port Forwarding Table...........................................................113
Port Triggering Setup............................................................................114
Application Layer Getaway Setup....................................................116
Universal Plug and Play Setup...........................................................117
Internet Group Multicast Protocol Setup.......................................118
Quality of Service Setup.......................................................................119
Priority Queue...........................................................................................120
Bandwidth Allocation.............................................................................121
Routing Setup...........................................................................................122
Wake on LAN Setup................................................................................123
Tools Setup................................................................................................124
System Time Setting..............................................................................125
Synchronizing Time with a Computer.............................................126
Dynamic Domain Name Service (DDNS) Setup............................127
Diagnose That Client Devices Are Connected.............................128
Upgrading the Router’s Firmware....................................................129
Backing Up the Router’s Settings.....................................................130
Rebooting the Router............................................................................131
Chapter 6 Advanced Settings...........................................................75
Configuring Advanced Settings............................................................76
Setting Up Parental Controls.................................................................78
Adding a Control Policy............................................................................79
Viewing Parental Policies.......................................................................82
Guest Network............................................................................................83
Configuring the DHCP Server Setting...............................................84
Viewing the DHCP Client List on the Guest Network.................85
IPv6.................................................................................................................86
Viewing the IPv6 Connection Status.................................................87
Configuring Static IPv6............................................................................88
Setting Autoconfiguration.....................................................................89
Configuring PPPoE....................................................................................90
Configuring 6to 4........................................................................................92
Viewing local Connections.....................................................................93
Firewall Setup.............................................................................................94
Configuring Advanced Settings...........................................................95
Configuring Demilitarized Zone...........................................................97
Configuring Denial of Service................................................................98 Appendix..........................................................................................132
Wall Mounting the Router....................................................................133
Virtual Private Network Setup..............................................................99
FCC Interference Statement...............................................................134
Configuring a VPN Tunnel Profile.......................................................100
Industry Canada Statement................................................................135
General........................................................................................................101
Europe – EU Declaration of Conformity .........................................136
SA (Security Association)......................................................................102 4
Chapter 1
Product Overview
Product Overview
Key Features
•
•
•
•
•
•
•
•
•
•
Dual Band Wireless AC1200 Draft IEEE 802.11ac and IEEE 802.11
a/b/g/n
Up to 300 Mbps in the 2.4 GHz frequency band and up to 867Mbps
in 5 GHz
Built-in 4-Port Gigabit Switch for optimal audio/visual streaming
USB Port to share and access media content in the home or when
you’re away from home with EnShare™
Next Generation IPv6 Compliant
Parental Controls
Up to 8 Guest Access settings (4 per frequency band)
Industry-standard Wireless Encryption and Security
VPN Server Support Lite-Business Applications
Easy Setup Wizard
Robust and Reliable Wireless Performance
The ESR1200 is a Dual-Band Wireless AC1200 Router with
a built-in 4-port Gigabit Ethernet switch. This cost effective
router can connect to DSL or cable modems to provide
high performance Internet access for desktop or laptop
computers, tablets, smartphones and a wide variety of home
entertainment devices such as HDTVs, set top boxes, Blu-ray
players and gaming consoles.
option to leverage Quantum Beam and the AC speed boost on
the less congested 5 GHz frequency for bandwidth intensive
applications like streaming HD video.
The router’s concurrent dual band design enables users to
connect numerous wireless devices to it, giving them the
Maximum data rates are based on draft IEEE 802.11ac and IEEE 802.11 standards. Actual throughput and range may vary depending on many factors; including environmental conditions, distance between devices, radio interference in the
operating environment, and mix of devices in the network. EnGenius Technologies, Inc. EnShare™ supports both FAT32 and NTFS USB formats. Transfer speeds of data from your router-attached USB storage device to a remote/mobile device
may vary based on Internet uplink and downlink speeds, bandwidth traffic at either send or receive locations, the data retrieval performance of the attached storage device, or other factors. EnGenius does not guarantee compatibility with
all USB drives. EnGenius does not warrant its products or EnShare from loss of data or loss of productivity time. Features and specifications subject to change without notice. Trademarks and registered trademarks are the property of their
respective owners. For United States of America: Copyright ©2013 EnGenius Technologies, Inc. All rights reserved.
Product Overview
A Media Sharing Platform
The ESR1200 is designed to access and share media for
devices on the home network. In addition to connecting home
entertainment components to any of its available Gigabit
Ethernet ports, the ESR1200 also includes a USB port for
attaching a USB storage device so wireless devices in the
home or away from the home can access or upload media
content wherever there is an available Internet connection
through EnShare™ - Your Personal Cloud.
USB Media Anywhere
with EnShare
TM
Attach USB storage to the ESR1200 and access
or upload video, music, and other media
throughout your home or away from home
from your smartphone, tablet, or laptop.
EnShare is available as an Internet portal for accessing stored
media connected to the USB port of the router (See the
Using EnShare document in the product packaging). EnShare
will also be available as an app for Apple iOS devices (iPads,
iPods and iPhones) and Android-based devices (smartphones,
tablet PCs, Kindle and other mobile readers) soon. The apps
will be available through Apple iTunes Store and Google Play
respectively.
More Guest Access Options
The ESR1200 also includes up to eight (8) separate
and discrete Guest Access options allowing the router’s
administrator to assign different names (SSIDs-Service Set
Identifiers) for each login to the home network so friends or
visitors can access the user’s Internet connection without
accessing personal data stored on networked computers in
the home.
Industry-standard Wireless Security
The router supports a variety of security features and
mechanisms including industry-standard WPA/WPA2 wireless
encryption to prevent unauthorized access to your network. It
also includes a built-in SPI (Stateful Packet Inspection) firewall
to help prevent attacks from malicious software (malware)
from the Internet. The router also supports IPv6.
Technical Specifications
Software Features
Device Interface
Gigabit WAN Port
4 Gigabit LAN Ports
USB2.0 Port
Push Button for WPS
Reset Button
Frequency Bands
2.400~2.484 GHz (11b/11g/11n)
5.18~5.82 GHz (11a/11n)
Operating Mode
AP Router/WDS
Wireless Features
Auto Channel Selection
Output Power Control
WMM (Wireless Multimedia)
MSSID (Multiple SSID)
IEEE Standards
802.11ac (draft)
802.11a/b/g/n
Up to 300 Mbps wireless speed on 2.4 GHz frequency
band and 867 Mbps on 5 GHz frequency band
802.3i/u/ab
LED Indicators
Power
WLAN (Wireless Connection)
Internet
Package Contents
ESR1200 Router
Power Adapter (12V 1.5 A)
Quick Start Guide
RJ45 Ethernet Cable
Power Specification
External Power Adapter
DC In, 12V 1.5A
Certifications
FCC/CE/IC
Physical/Environmental Conditions
Operating Temperature: 0º~40º Celsius
Humidity: 90% or less (non-condensing)
Storage Temperature: -20º~60º Celsius
Humidity: 95% or less (non-condensing)
Security
WEP/WPA-PSK/WPA2-PSK
TKIP/AES
Hidden SSID
MAC Address Filtering
802.1X Authentication
DDoS
DHCP Server/Client
SPI (Stateful Packet Inspection)
NAT
Port Forwarding
DMZ
Port Mapping/Triggering
VPN Server (PPTP/L2TP)
VPN Client (PPTP/L2TP)
VPN Pass-through (PPTP/L2TP/IPSec)
Rule Based (IP Address Ranges, Port Block ICMP
VPN Tunnel (Maximum 5)
QoS
IP Filtering
Port Filtering
DDNS
IPv6 Pass-through
MAC Clone
Traffic Monitor
WAN Type: PPPoE/DHCP/Static IP
USB Features: SAMBA
Physical Interface
Dimensions and Weights
Weight: 0.5 lbs.
Diameter: 6.36”
Height: 1.64”
When considering the placement of the
router
remember the following:
• It must be close to an electrical
outlet.
• For optimal wireless connectivity,
place the router near the center of
the room if possible, at a high level
1 WLAN 5 GHz LED
2 WLAN 2.4 GHz LED
3 Power LED
4 WAN Port/(Internet)
Status LED
5 WPS (Wireless Protected
Setup) LED
Other electronic devices and some
architectural construction materials
or impediments may interfere with
the wireless signal(s) of the router
and reduce its range or coverage. Try
to minimize the number of walls or
floors that the router’s signal needs to
penetrate to connect to other wireless
devices.
6 DC Power Jack — Connects the ESR Series Router to its DC
power adapter
7 WAN Port — Connects the ESR Router to a cable or DSL modem
to access the user’s broadband (Internet) connection
8 LAN Ports (1 – 4) — For connecting home entertainment
components, computers, or other Ethernet-enabled devices
using Ethernet cables
9 Reset Button — For resetting the router to its factory default
settings by pressing button for more than 11 seconds or until
the Power LED starts flashing.
10 USB Port For connecting a USB Storage Device
11 WPS Button — Wi-Fi Protected Setup button. To associate
another WPS-enabled client device (computer, wireless media
bridge, USB adapter, etc.) press the WPS button for 2 to 5
seconds on the router while also pressing the WPS button on
the end device.
Chapter 2
Controlling the Router Through
Its Web Configuration Interface
10
Logging In
During the Quick Start Guide procedure, you should have
successfully logged into the router’s Web Configuration User
Interface (essentially the router’s operating system that
controls how it operates) and established some initial settings
and controls for the router.
If you wish to change the router’s settings (such as establish
a new username and password for the person who manages
and maintains the router, set Parental Controls, establish
a Guest Access-SSID setting for visitors, or any number of
other settings) you can log into the Web Configuration again
through a web browser (Internet Explorer, Safari, Chrome,
Firefox) on your computer or tablet device.
The default login settings are:
username: admin
password: admin
To do this, enter the router’s default IP address of
192.168.0.1 into your browser’s address window.
1. At the login screen, enter your username and a password
2. Click Login to continue.
It’s highly recommended that if you haven’t done so already,
to change these default names to something unique so your
router and the devices connected to it on your home network
are more secure.
11
Viewing the Web Configuration Dash Board
The Home Page screen of the Web Configuration interface, or dashboard, provides access to the router’s settings and controls.
Logout
Language
IP Cam Viewer
USB Storage Sharing
Network Settings
Home Page
Setup Wizard
Home
12
Home Page
Language
The Language link displays the menu to set the OSD language.
The Home Page displays the areas within the Web
Configuration to which you can navigate: Setup Wizard,
Network Settings, USB Storage Sharing, IP Cam Viewer,
Language, and Logout
Logout
The Logout link closes the router’s Web Configuration
interface from any screen.
Home
The Home link takes you back to the dashboard screen no
matter where you are in the Web Configuration interface.
Setup Wizard
The Setup Wizard link starts the wizard that automatically
configures the router.
Network Settings
The Network Settings link displays the menus to manually
configure the router.
USB Storage Sharing
The USB Storage Sharing link displays the menus to access
shared storage devices connected to the router.
IP Cam Viewer
The IP Cam Viewer link displays the menus to view an IP
camera connected to the network.
13
Web Menus Overview
System
View and edit settings that affect system functionality.
Operation Mode
Configure the device to be a router or WDS access point.
Status
Displays the summary of the current system status.
Schedule
Schedule services to start and stop at specific times or intervals.
Event Log
View recorded system operations and network activity events.
Monitor
View the current network traffic bandwidth usage.
Language
Configure the application menu and GUI language.
IP Camera
View the IP cameras connected to the ESR Series Router.
14
Internet
View and edit settings that affect network connectivity.
Status
Displays a summary of the Internet status and type of connection.
Dynamic IP
Setup a dynamic IP connection to an ISP (Internet Service Provider).
Static IP
Setup a static IP connection to an ISP.
PPPoE
Setup a PPPoE connection to an ISP.
PPTP
Setup a PPTP connection to an ISP.
L2TP
Setup an L2TP connection to an ISP.
15
Wireless 2.4 GHz
View and edit settings for 2.4 GHz wireless network connectivity.
Status
View the current wireless connection status and related information.
Basic
Configure the minimum settings required to setup a wireless network connection.
Advanced
Configure the advanced network settings.
Security
Configure the wireless network security settings.
Filter
Establish a list of client devices (computer, tablets, smartphones, printers, etc.)
based on their MAC (Media Access Control) numbers that are allowed to wirelessly
connect to the 2.4 GHz network.
WPS
Automates the connection between a wireless device and your encrypted router
using an 8-digit PIN.
Client List
View the 2.4 GHz wireless devices currently connected to the network.
16
Wireless 5 GHz
View and edit settings for 5 GHz wireless network connectivity.
Status
View the current wireless connection status and related information.
Basic
Configure the minimum settings required to setup a wireless network connection.
Advanced
Configure the advanced network settings.
Security
Configure the wireless network security settings.
Filter
Establish a list of client devices (computer, tablets, smartphones, printers, etc.)
based on their MAC (Media Access Control) numbers that are allowed to wirelessly
connect to the 5 GHz network.
WPS
Automates the connection between a wireless device and your encrypted router
using an 8-digit PIN.
Client List
View the 5 GHz wireless devices currently connected to the network.
17
Parental Controls
View and edit settings for parental controls.
Wizard
Enable or disable the Parental Controls function. The menu also provides information for configuring parental control policies.
Web Monitor
The menu provides a log of the events for defined parental control policies.
18
Guest Network
View and edit settings for a guest network.
Selection
Enable or disable the Guest Network function.
DHCP Server Setting
Configure the Guest Network DHCP server settings.
DHCP Client List
Configure the Guest Network client list.
19
IPv6
View and edit settings for the IPv6 protocol.
Basic
Allows you to enable or disable the IPv6 and IPv6 Pass-through functions.
Status
Shows IPv6 LAN connection details.
Static IPv6
Configure the IPv6 protocol.
Auto Configuration
Configure the IPv6 by obtaining the information through the ISP provider.
PPPoE
Configure the PPPoE network protocol and obtain information from your ISP
(Internet Service Provider).
6to4
Allows IPv6 packets to be transmitted over an IPv4 network.
Link Local
Configure the IPv6 link local address.
20
Firewall
View and edit settings for the network firewall.
Basic
Enable or disable the network firewall.
Advanced
Configure virtual private network (VPN) packets.
DMZ
Redirect packets from the WAN port IP address to a particular IP address on the
LAN.
DoS
Enable or disable blocking of DoS (Denial of Service) attacks.
ACL
Configure access control lists.
21
VPN
View and edit settings for VPN tunnelling.
Status
View the status of current VPN tunnels.
Profile Setting
Manually configure VPN tunnels.
User Setting
Configure users, user ID and password combinations, and assign access to specific
VPN tunnels.
Wizard
Automatically configure VPN tunnels with guidance from the software.
22
USB Port
For viewing and editing settings for storage sharing.
EnShare™
Enables or disables the EnShare remote access function.
File Sharing
Enables or disables the Samba sharing function.
File Server
Enables and configures the File Server function.
DLNA
Enables the discovery of DLNA devices (includes some HDTVs, game consoles,
set top boxes/media players, Blu-ray players, smartphones, and network attached
storage) on the home network.
23
Advanced
View and configure advanced system and network settings.
NAT
Enable or disable Network Address Translation (NAT).
Port Mapping
Re-direct a range of service port numbers to a specified LAN IP address.
Port Forwarding
Configure server applications to send and receive data from specific ports on the
network.
Port Triggering
Configure applications that require multiple connections and different inbound and
outbound connections.
ALG
Configure the application layer gateway (ALG).
UPnP
Enable or disable Universal Plug and Play (UPnP) functionality.
IGMP
Enable or disable the Internet Group Multicast Protocol (IGMP).
24
QoS
Configures the network quality of service (QoS) setting by prioritizing the uplink
and downlink bandwidth.
Routing
Configure static routing.
WOL (Wake On LAN)
Configure Wake on LAN to turn on a computer over the network.
25
Tools
For viewing and configuring the router’s operating system and network tools
settings.
Admin
For setting the administrator’s password used to log into the router.
Time
For configuring the system time on the router.
DDNS
Maps a static domain name to a dynamic IP address.
Diagnosis
Perform a Ping test to verify whether a specific device is connected to the LAN.
Firmware
For updating the router’s firmware.
Backup
For loading or saving the configuration settings to or from a backup file or to
restore the router to its factory default settings.
Reset
Reboots the router.
26
Chapter 3
Installation Setup Wizard
27
Internet Setup Wizard
Setup Wizard
Home
Use the Wizard to detect and set up
the type of Internet connection when
you need to set up a secure wireless
connection, create an administrator
password to secure the device, or set the
router’s date and time properties.
To use the Internet Setup Wizard, follow
these steps:
1. Click the Wizard button to show the
Wizard start screen.
2. Click Next to continue with the setup
procedure.
28
Setting Up Your Internet Connection
1. Decide how to set up the Internet connection.
Note:It is recommended to let the device setup the Internet
connection automatically.
• Select Auto Detect to let the Wizard set up the Internet
connection.
• Select Manual Setup to set the properties yourself.
Note: The connection types available are static IP, PPPoE,
Dynamic IP, PPTP, and L2TP.
4. Click Next to continue, Prev to return to the previous
screen, or Cancel to stop the procedure.
2. Click Next to continue or Prev to return to the previous
screen.
If you selected Manual Setup, follow these steps:
3. Select the Internet connection type and enter the
connection properties.
29
Setting Your Wireless Security
Setting wireless encryption for 2.4 GHz and 5 GHz networks.
To encrypt the wireless signals for either or both of the frequency
bands in the ESR1200 router, follow these steps:
1. Enter the router name in the wireless Name (SSID) text field.
2. Select the security level from the Encryption drop-down list.
Important: To ensure the network is secure, it is
recommended to select High for an encryption level.
3. Enter a password in the Encryption Key text field.
4. Repeat steps 1 through 3 to encrypt the 5 GHz band
5. Click Next to continue, Prev to return to the previous screen, or
Cancel to stop the procedure.
30
Setting Your Router’s Administrator Password
Set up a password to log into the ESR Series Router.
1. Enter a password in the New Password text field.
2. Enter the same password in the Repeat New Password text field.
3. Click Prev to return to the previous screen, Skip to skip this procedure, Next to
continue, or Cancel to stop the procedure.
31
Setting Your Router’s Time Zone
Setup date and time syncronization on the ESR Series Router
with a computer or an Network Time Protocol (NTP) server.
To synchronize date and time settings with a computer, follow
these steps:
1. Select Synchronize with PC (computer) from the Time Setup
drop-down list. The date and time values are shown in the PC
Date and Time text field.
2. Click Prev to return to the previous screen, Apply to save the
settings, or Cancel to stop the procedure.
To synchronize the date and time settings with an NTP server,
follow these steps:
1. Select Synchronize with NTP Server from the Time Setup
dropdown list.
2. Select a time zone value from the Time Zone drop-down list.
3. Enter an IP address or domain name of an NTP server in the
NTP Server text field.
4. Click the Enable Daylight Savings check box to enable or
disable daylight savings time.
5. Select the date and time values when daylights savings
time starts in the Start Time drop-down lists.
32
6. Select the date and time values when daylights savings
time ends in the End Time drop-down lists.
7. Click Prev to return to the previous screen, Apply to
save the settings, or Cancel to stop the procedure.
33
Status and Save Settings
This screen lets you review, change, and save your Internet
connection, save wireless security settings or setup up a userspecified name for the default EnGenius DDNS service.
To review or modify the device settings, follow these steps:
1. Review the settings shown on the screen for the Internet
connection, 2.4 GHz and 5 GHz networks, and the router
administrator login.
2. You can change settings to the Internet connection and
wireless network settings by clicking the Setup button.
You may wish to use a different name that’s easier to remember
for the default EnGenius DDNS service used for the EnShare™
feature. To specify your own DDNS name, follow these steps:
3. The Enable option should be selected by default.
a. Enter the name in the Domain Name text field.
b. Select a time interval to refresh the DNS records from the
Refresh dropdown list.
c. Click Apply to save the DDNS name you have entered.
WARNING! Selecting Disable in the DDNS Settings/
Status field will disconnect the router’s connection
to the default EnGenius DDNS server and as a result
will disable the EnShare feature which lets you access
media from a USB storage device connected to your
ESR pod router when you’re away from your home.
4. Click Save to exit the Web Configuration interface. The router
will reboot (restart) to apply all the settings you’ve specified.
Devices connected to the router will temporarily lose their
Internet connection. The reboot may take several seconds
before the router and your Internet connection are once again
available.
34
Chapter 4
Basic Network Settings
35
Network Settings
Network Settings
Viewing System Status
Home
To see a more detailed view of the router’s status than
the information displayed on the Home page of the Web
Configuration interface, from the Home Page click on the
Network Settings button in the upper navigation bar.
Note:
If a feature or function does not apply to all modes, a note indicates
which modes are applicable. Otherwise, it is assumed the feature
or function applies to all modes.
36
Status
Application Version
The version of the router’s firmware.
To view the Status settings, click System and then click Status.
On the Status page, you can view a summary of the current
router system status including the router’s (hardware/software
version, date/time), wired network (LAN), and wireless network
(WLAN) information.
Note: To update the router’s firmware, visit www.engeniustech.
com and go to the product page for your router, then select the
Downloads tab at the bottom of the web page to see if a newer
version of the firmware is available.
Model
The model name of the ESR Series Router.
Mode
The operating mode of the ESR Series Router.
Uptime
The amount of time the ESR Series Router has been connected
for the current session.
Current Date/Time
The current system date and time.
Hardware Version
The hardware version number of the router.
Serial Number
The serial number of the router (required for customer service or
support).
37
WAN Settings
Attain IP Protocol
Displays the IP protocol in use for the router. It can be a
dynamic or static IP address.
IP Address
The router’s IP address as designated by an ISP (Internet Service
Provider).
Subnet Mask
The router’s WAN Subnet mask as designated by an ISP provider.
Default Gateway
The router’s Gateway address as designated by an ISP provider.
MAC Address
The router’s WAN MAC (Media Address Control) address. The
router’s MAC address is located on the label on the bottom panel
of the router and is unique for each router.
Primary DNS
The primary DNS of an ISP provider.
Secondary DNS
The secondary DNS of an ISP provider.
38
LAN Settings
IP Address
The router’s local IP address. The default LAN IP address is:
http://192.168.0.1
To access the Web Configuration interface for the router, type
this address into the address (URL) field of your web browser.
This can only be done in the same physical location where the
router resides (your home network).
Subnet Mask
The router’s local Subnet mask.
DHCP Server
The DHCP setting status (Default: Enabled). The DHCP (Dynamic
Host Control Protocol) is a software mechanism in your router
that assigns IP addresses to wired and wireless devices on your
network, for example, a computer, printer, tablet or HDTV on your
network may be assigned an IP address of http://192.168.0.104.
Note how the address is essentially an extension or addition of
your router’s IP address.
MAC Address
The router’s unique MAC address.
39
WLAN Settings
Channel
The communications channel used by all stations, or computing
devices, on the network.
ESSID
The ID value of a set of one or more interconnected basic service
sets (BSSs).
Security
The security setting status (Default: Disabled).
BSSID
The unique ID of the BSS using the above channel value on this
router. The ID is the MAC address of the BSSs access point.
Associated Clients
The number of clients associated (actively linked to the router via
a wireless or wired/Ethernet connection) with this SSID.
40
Guest Network
Guest Network
The guest network status. (Default: Disabled)
IP Address
The Guest Network’s LAN IP address.
Subnet Mask
The Guest Network’s local Subnet mask.
DHCP Server
The Guest Network DHCP setting status (Default: Enabled).
Guest Network Interface
The SSID (Service Set Identifier) of the Guest Network.
41
Configuring the LAN
(Local Area Network)
The settings on this page allow you to configure the wired
network settings. Devices connected to the router’s Ethernet
ports comprise its LAN. The router’s IP is defined in the IP
Address field. The default setting of the DHCP server is set
to Enabled so that networked clients (computers, home
entertainment components, printers, etc.) will automatically be
assigned IP addresses by the router.
More advanced users may wish to configure the DNS server
settings to meet their specific requirements. Changing the
settings in this section are not necessary for most situations.
LAN IP
IP Address
For configuring the router’s LAN IP address.
To view the LAN settings, click System, then click LAN.
IP Subnet Mask
For configuring the router’s LAN Subnet mask
Note: Keep the router’s default values if you are uncertain of
the settings values.
802.1d Spanning Tree
The Spanning Tree is disabled by default. When enabled, the
Spanning Tree feature prevents network loops (transmissions
won’t pass the same node twice or several times to reach the
destination).
Note:
The default device IP address is 192.168.0.1.
42
DHCP Server
The DHCP server assigns IP addresses to the devices on the LAN.
DHCP Server
Enable or disable the DHCP server (Default: Enabled).
Lease Time
Configure the amount of time each allocated IP address can be
used by a client.
Start IP
The first IP address in the range of addresses assigned by the
router.
End IP
The last IP address in the range of addresses assigned by the
router.
Domain Name
The domain name of the router.
43
Configuring Dynamic Host Configuration Protocol
This window allows you to view and configure Dynamic Host Configuration Protocol (DHCP) addresses.
WARNING! Do not modify the settings in this section without a thorough understanding of the parameters.
To view the DHCP settings, click System then click DHCP.
DHCP Client Table
Displays the connected DHCP clients whose IP addresses are
assigned by the DHCP server of the router.
IP Address
Displays the IP address of the static DHCP client device
in the table.
MAC Address
Displays the MAC address of the static DHCP client device
in the table.
Expiration Time
The date and time when the current DHCP address
is no longer valid.
Click Refresh to update the table.
44
Enable Static DHCP IP
There are reasons why you may want to enable a static IP
address on a client device on your ESR router’s network.
On occasion, if there are power outages or if you’ve reconfigured
the settings on your ESR router and reboot (restart) it to apply
the new settings, the previous IP address that the router’s DHCP
server assigned to one or more devices on the network may have
changed. Some client devices on your network may also have
web configuration interfaces (set top boxes, Network Attached
Storage, etc.) that are accessible from the router’s assigned
IP address from its DHCP server, so the client device can be
managed. Thus if the client device’s IP address changes from
time to time, it may be difficult linking to it unless you find its
new address through the ESR router’s DHCP Client Table.
MAC Address
Enter the MAC address of the device to add as a static DHCP
client.
Click Add to add the device to the static DHCP client table or
Reset to return the table to its previous state.
If you wish to avoid this, then the Enable Static DHCP IP option
allows you set a static (essentially a permanent) address for
given client devices on your network.
To do so, select the Enable Static DHCP IP option.
IP Address
Enter the IP address of the device to add as a static DHCP client.
45
Current Static DHCP Table
Allows you to view the active static DHCP IP addresses that
have been manually assigned to client devices with their
corresponding MAC addresses.
No. (Number)
Displays the ID of the static DHCP client device in the table.
IP Address
Displays the IP address of the static DHCP client device in the
table.
MAC Address
Displays the MAC address of the static DHCP client device in the
table.
Select
Click to select static DHCP client devices to be deleted.
Click Delete Selected to remove a selected address. Click Delete
All to remove all addresses from the table. Click Reset to return
the table to its previous state. Click Apply to save the settings or
Cancel to discard changes.
46
Configuring Event Logging
The logging service records and displays important system
information and activity on the network. The events are stored in
a memory buffer with older data overwritten by newer when the
buffer is full.
To view the Log settings, click System and then click Log.
Log Message List
Select Enable Logging to Syslog Server
Click Save to start logging information to the system.
Log Message window
Shows the current system operations and network activity.
Click Save to save the message list to a text file, Clear to discard
message from the memory buffer, or Refresh to clear previous
messages and write new messages to the memory buffer.
Click Apply to save the changes.
47
Monitoring Bandwidth Usage
This tool allows you to view real-time bandwidth usage for WAN
(Wide Area Network - or Internet), LAN (Local Area Network) and
WLAN (Wireless Local Area Network) traffic. For the ESR1200,
it shows both the bandwidth traffic in both the 2.4 and 5 GHz
frequency bands.
To view the Bandwidth Monitor settings, click System, then click
Monitor.
The screens display the active bandwidth usage for both the LAN
and WLAN networks as well as the bandwidth being used on the
WAN connection.
48
Configuring the System Language
The ESR router’s Web Configuration interface supports multiple
languages.
To view the Language settings, click System, then click
Language.
Select the system language you wish to use from the drop-down
menu.
49
Configuring IP Cameras
This ESR router supports up to four (4) EnGenius IP Cameras
simultaneously. If no IP Camera is detected, please check that the
IP Camera’s IP address and UPnP client are configured correctly.
To view the IP Camera settings, click System, then click IP
Camera.
Before starting this procedure, you must connect your EnGenius
IP camera to the network.
Make sure the camera is powered on.
Click the Refresh button to view a listing of available devices.
Note: The "IP Camera" function supports EnGenius IP
Camera products only.
50
Configuring Internet Settings
View Internet Status
IP Address
The router’s WAN IP address.
The WAN Settings, or Internet Status, page shows a summary of
the current Internet connection information. This section is also
shown on the System Status page.
Subnet Mask
The router’s WAN subnet mask.
To view the Status settings, click Internet, then click Status.
Default Gateway
The ISP’s Gateway IP address.
WAN Settings
To view the WAN Settings, click Internet then select Status.
MAC Address
The router’s WAN MAC address. The router’s MAC address is
located on the label on the back side of the router.
Primary DNS
The primary DNS address of an ISP provider.
Secondary DNS
The secondary DNS address of an ISP provider.
Attain IP Protocol
Display the IP Protocol type used for the ESR Series Router
(Dynamic IP Address or Static IP Address).
51
Configuring Dynamic IP
Dynamic IP addressing assigns a different IP address each time
a device connects to an ISP (Internet Service Provider) and most
commonly used by cable ISPs.
To view the Dynamic IP, click Internet then select Dynamic IP.
Dynamic IP
Hostname
Assign a name for the Internet connection type. This field can be
blank.
MTU (Maximum Transmission Unit)
Allows you to configure the MTU. The MTU specifies the largest
packet size permitted for an internet transmission. The factory
default MTU size for Dynamic IP (DHCP) is 1500. The MTU size
can be set between 512 and 1500.
Clone MAC
Enter the MAC address of your computer’s (or tablet’s) network
embedded Network Interface Card (NIC) in the MAC address field
and click Clone MAC.
Note: Some ISP providers require registering the MAC address of
the Network Interface Card (NIC) connected directly to the cable or
DSL modem. Clone MAC masks the router's MAC address with the
MAC address of the computer’s NIC.
52
DNS Servers
The DNS server translates a domain or website name into a URL
(Uniform Resource Locator), or Internet address. There are two
options to choose from: From ISP or User-Defined. Select From ISP to
retrieve the DNS address value from the ISP; select User-Defined to
assign a custom DNS server address.
DNS Server
Configure the type of DNS server. (Default = From ISP)
First DNS Server
Configure the first, or primary, DNS server.
Second DNS Server
Configure the second, or secondary, DNS server.
Click Apply to save the settings or Cancel to discard the changes.
53
Configuring Static IP
Setting a static IP address allows an administrator to set a
specific IP address for the router and guarantees that it can not
be assigned a different address.
To view the Static IP settings, click Internet, then click Static
IP.
Static IP
IP Address
The router’s WAN IP address.
MTU (Maximum Transmission Unit)
The MTU specifies the largest packet size permitted for an
internet transmission. The factory default MTU size for static IP
is 1500. The MTU size can be set between 512 and 1500.
Subnet Mask
The router’s WAN subnet mask.
MAC Address
The router’s MAC address.
Default Gateway
The WAN gateway address.
Click Apply to save the settings or Cancel to discard the
changes.
Primary DNS
The primary DNS server address.
Secondary DNS
The secondary DNS server address.
54
Configuring PPPoE
Point-to-Point Protocol over Ethernet (PPPoE) is used mainly by
ISPs that provide DSL modems to connect to the Internet.
To view the PPPoE settings, click Internet, then click PPPoE.
Username
Enter the username assigned by an ISP.
Password
Enter the password assigned by an ISP.
Idle Timeout
Configure the maximum idle time (1 to 1,000 minutes) allowed
for an inactive connection.
Service Name
Enter the service name of an ISP (optional).
MTU (Maximum Transmission Unit)
Enter the (MTU). The MTU specifies the largest packet size
permitted for an internet transmission (PPPoE default: 1492).
The MTU size can be set between 512 and 1492.
Clone MAC
Enter the MAC address of the devices’ network interface
card (NIC) in the MAC address field and click Clone MAC.
Authentication Type
Select the type of authentication provided by the ISP: Auto, PAP,
or CHAP. If unsure of the best setting, select Auto or check with
your Internet Service Provider.
Note: Some ISP providers require registering the MAC address
of the network interface card (NIC) connected directly to
the cable or DSL modem. Clone MAC masks the router’s
MAC address with the MAC address of the computer’s NIC.
Type
Configure the connection type between the router and the
ISP. Select one of the following: Keep Connection, Automatic
Connection or Manual Connection.
Click Apply to save the settings or Cancel to discard the
changes.
55
Configuring PPTP
PPTP (Point-to-Point Tunnelling Protocol) is used in association
with virtual private networks (VPNs). There are two parts to
a PPTP connection: the WAN interface settings and the PPTP
settings.
To view the PPTP settings, click Internet, then click PPTP.
WAN Interface Settings
Dynamic IP Address
WAN Interface Type
Select Dynamic IP Address to assign an IP address provided by an
ISP.
Hostname
Enter a hostname of an ISP. (optional).
Clone MAC
Enter the MAC address of the computer’s (or tablet’s) embedded
Network Interface Card (NIC) in the MAC address field and click
Clone MAC.
Note: Some ISP providers require registering the MAC address of
the network interface card (NIC) connected directly to the cable or
DSL modem. Clone MAC masks the router’s MAC address with the
MAC address of the computer’s NIC.
56
PPTP Settings
User Name
Enter the username assigned by your ISP.
Password
Enter the password assigned by your ISP.
Service IP Address
Enter the PPTP server IP address provided by your ISP.
Idle Timeout
Configure the maximum amount of time, in minutes, allowed for
inactive Internet connection. The Internet connection will be
dropped when the maximum idle time is reached. Valid values are
between 1 and 1,000.
Connection ID
Enter the connection ID provided by your ISP (optional).
MTU (Maximum Transmission Unit)
Enter MTU. The MTU specifies the largest packet size (Default:
1462) permitted for an Internet transmission. The MTU size can
be set between 512 and 1492.
Click Apply to save the settings or Cancel to discard the changes.
Type
Configure the connection type between the router and the
ISP. Select one of the following: Keep Connection, Automatic
Connection or Manual Connection.
57
Configuring L2TP
L2TP (Layer 2 Tunneling Protocol) is used in association with
VPNs (Virtual Private Networks). There are two parts to a L2TP
connection:
1. The WAN interface settings
and
2. The L2TP settings.
To view the L2TP settings, click Internet, then click L2TP.
WAN Interface Settings
Dynamic IP Address
WAN Interface Type
Select Dynamic IP Address to assign an IP address provided by
an ISP.
Hostname
Enter a hostname of an ISP (optional).
Clone MAC
Enter the MAC address of your computer’s embedded Network
Interface Card (NIC) in the MAC address field and click Clone MAC.
Note: Some ISP providers require registering the MAC address
of the network interface card (NIC) connected directly to
the cable or DSL modem. Clone MAC masks the router’s MAC
address with the MAC address of the computer’s NIC.
58
L2TP Settings
Username
Enter the username assigned by an ISP.
Password
Enter the password assigned by an ISP.
Service IP Address
Enter the L2TP server IP address provided by an ISP.
Idle Timeout
Configure the maximum amount of time, in minutes, allowed for
inactive Internet connection. The Internet connection will be
dropped when the maximum idle time is reached. Valid values are
between one and one thousand.
Connection ID
Enter the connection ID provided by an ISP (optional).
MTU (Maximum Transmission Unit)
Enter MTU. The MTU specifies the largest packet size (Default:
1460) permitted for an Internet transmission. The MTU size can
be set between 512 and 1492.
Click Apply to save the settings or Cancel to discard the changes.
Type
Configure the connection type between the router and the
ISP. Select one of the following: Keep Connection, Automatic
Connection or Manual Connection.
59
Configuring DS-Lite
Dual-Stack Lite, or DS-Lite, allows ISPs to stop IPv4 addresses
from reaching a customer’s network devices and only use IPv6.
To view the DS-Lite settings, click Internet, then click DS-Lite.
DS-Lite Configuration
Select DS-Lite DHCPv6 Option or Manual Configuration.
AFTR IPv6 Address
Enter the AFTR IPv6 connection type.
B4 IPv4 Address
Enter an Optional B4 IPv4 address.
WAN IPv6 Address
Enter the WAN IPv6 address.
IPv6 WAN Default Gateway
Enter the IPv6 WAN default Gateway address.
Click Apply to save the settings or Cancel to discard the changes.
60
Wireless LAN Setup
To view the Wireless Basic settings, click Wireless and then
select Basic.
Radio
Enable or disable the wireless radio. If the wireless radio is
disabled, wireless Access Points are not available.
Mode
Select the wireless operating mode for the router. Two modes
are available: Access Point or Wireless Distribution System (WDS)
mode.
AP (Access Point)
Provides a connection Access Point for wireless devices.
WDS (Wireless Distribution System)
Allows the wireless network to be expanded using multiple
Access Points without wired connections.
Click Apply to save the settings or Cancel to discard changes.
61
Access Point Mode
These instructions apply to both the 2.4 GHz and 5 GHz frequency bands.
The router by default is already configured in Access Point Mode. For optimum connectivity to a number of different wireless client
devices, it’s recommended that you keep the router in its default wireless settings. You can choose to have the router associate
only with certain iterations (IEEE standards) and by doing so this will either positively or negatively affect the router’s speed and
throughput performance.
Band
Select a wireless standard for the network from the following
options:
• 2.4 GHz (IEEE 802.11b)
• 2.4 GHz (IEEE 802.11n)
• 2.4 GHz (IEEE 802.11b/g)
• 2.4 GHz (IEEE 802.11g)
• 2.4 GHz (IEEE 802.11b/g/n)
•
•
•
•
Auto Channel
Enable or disable having the router automatically select a
channel for the wireless network. Auto Channel is enabled by
default. Select Disable to manually assign a specific channel.
(Default = Disable)
Check Channel Time
When Auto Channel is enabled, select a time period that the
system will check for the appropriate channel for the router.
5 GHz (IEEE 802.11a)
5 GHz (IEEE 802.11n)
5 GHz (IEEE 802.11a/n)
5 GHz (IEEE 802.11 draft ac)
Channel
When Auto Channel is disabled, select a channel to assign to
the wireless network. Valid values are from one to eleven in
the US and one to thirteen in the EU.
Enable SSID#
Select the number of wireless groups, between one and four,
available on the network.
SSID[#]
Enter the name of the wireless network(s).
62
Wireless Distribution System Mode
Configuring the router’s wireless settings for WDS (Wireless Distribution System) mode.
Channel
Select a channel to assign to the wireless network. Valid values
are from one to eleven in the US and one to thirteen in the EU.
MAC Address [#]
Enter the MAC address(es) for the wireless Access Point(s)
that are part of the WDS.
WDS Data Rate
Select the data rate for the WDS.
Set Security
Click Set Security to set up the WDS security settings screen.
63
WDS Security Settings Screen
Selecting the type of WDS encryption (Disable, WEP or WPA PreShared Key) you would like for the wireless network.
Wired Equivalent Privacy (WEP)
Key Length
Select between 64-bit and 128-encryption.
Key Format
Select the type of characters used for the WEP Key: ASCII
(5 characters) or Hexadecimal (10 characters).
Default Key
Select the default encryption key for wireless transactions.
Encryption Key [#]
Enter the encryption key(s) used to encrypt the data packets
during data transmission.
64
Chapter 5
Wireless Encryption
65
Wi-Fi Protected Access (WPA) Pre-Shared Key
WPA Type
Select the type of WPA.
• WPA Temporal Key Integrity Protocol (TKIP): This generates
a 128-bit key for each packet.
• WPA2 Advanced Encryption Standard (AES):
Government standard packet encryption which is
stronger than TKIP.
Pre-Shared Key Type
Select the type of pre-shared Key as Passphrase (ASCII) or Hexadecimal.
Pre-Shared Key
Enter the pre-shared Key value.
66
Configuring Security
Enabling security options on the wireless network helps to
prevent intrusions to systems on the wireless network.
To view the Security settings, click Wireless then select
Security.
SSID Selection
Select the wireless network group in which you wish to change
its wireless security settings.
Broadcast SSID
Enable or disable the broadcast SSID. Choose whether or not the
wireless group is visible to other members.
Wi-Fi Multimedia (WMM)
Enable or disable quality of server (QoS) to optimize the
streaming for bandwidth sensitive data such as HDTV video
streaming, online gaming, VoIP, video conferencing, etc.
Encryption
Select the encryption type for the router.
Enable 802.1x Authentication
Check the box to enable or disable 802.1x authentication.
67
Encryption Type
Enabling encryption is strongly encouraged because unauthorized parties within range of your router’s wireless signal may attempt
to access your wireless network and then gain access to private information on devices on your network. It’s highly recommended
that you encrypt your router with WPA2 (AES) for optimal security and throughput performance. Always select a strong passphrase
greater than 8 characters long and comprised of letters, numbers, and symbols. Please make note of the passphrase and keep it in a
secure location somewhere in your home in case you need to retrieve it.
IMPORTANT! WPA2 (AES) offers much stronger security than WEP (Wired
Equivalent Privacy) which has been and can be comprimised.
Click Apply to save the settings or Cancel to discard the changes.
Wi-Fi Protected Access (WPA)
Pre-Shared Key
WPA Type
Select the type of WPA from the following:
• WPA2 Advanced Encryption Standard (AES):
RECOMMENDED — Government standard packet encryption
which is stronger than TKIP.
• WPA Temporal Key Integrity Protocol (TKIP): Generates a
128-bit key for each packet.
• WPA2 Mixed: Mixed mode allows client devices to first
associate to the router using WPA2, and if they fail to
connect, then they are connected via WPA (TKIP).
Pre-Shared Key Type
Select the type of pre-shared key as Passphrase (ASCII) or
Hexadecimal.
Pre-Shared Key
Enter the Pre-sShared Key value.
68
WPA RADIUS
Using a RADIUS server to authenticate wireless stations and
provide a session key to encrypt data during communications.
WPA Type
Select the type of Wireless Protected Access (WPA) from the
following:
• WPA2 Advanced Encryption Standard (AES):
RECOMMENDED — Government standard packet encryption
which is stronger than TKIP.
• WPA Temporal Key Integrity Protocol (TKIP): Generates a
128-bit key for each packet.
• WPA2 Mixed: Mixed mode allows client devices to first
associate to the router using WPA2, and if they fail to
connect, then they are connected via WPA (TKIP).
RADIUS Server IP Address
Enter the IP address of the server.
RADIUS Server Port
Enter the port number of the server.
RADIUS Server Password
Enter the password of the server.
69
Wired Equivalent Privacy (WEP)
Key Length
Select between 64-bit and 128-encryption.
Authentication Type
Select the type of authentication from the following:
• Open System: Wireless stations can associate with the router
without WEP encryption
• Shared Key: Devices must provide the corresponding WEP
key(s) when connecting to the router
• Auto: The router automatically detects whether Open System
or Shared Key is being used
Key Type
Select the type of characters used for the WEP Key: ASCII
(5 characters) or Hexadecimal (10 characters).
Encryption Key [#]
Enter the encryption key(s) used to encrypt the data packets
during data transmission.
Enable 802.1x Authentication
Enable or disable 802.1x authentication.
70
Configuring Filters
WARNING! Incorrectly changing these settings may cause the device to stop functioning. Do
not modify the settings in this section without a thorough understanding of the parameters.
When Enable Wireless Access Control is selected, only wireless clients with MAC addresses listed in the table are allowed to connect
to the wireless network.
To view the Filter settings, click Wireless then select Filter.
Enabling Wireless Access Control
Select “Enable Wireless Access Control”
Description
Enter a description of the device
allowed to connect to the network.
MAC Address
Enter the MAC Address of the
wireless device.
Click Add to append a new device
to the list or Reset to discard changes.
71
MAC Address Filtering Table
No. (Number)
The sequence number of the device.
Description
The description of the device.
MAC Address
The MAC address of the device.
Select
Indicates the device(s) that can have actions performed on
them.
Click Delete Selected to remove selected devices from the
list.
Click Delete All to remove all devices from the list.
Click Reset to discard changes. Click Apply to save the settings
or Cancel to discard changes.
72
Configuring Wi-Fi Protected Setup
Wi-Fi Protected Setup (WPS) is an quick and easy way to associate a new wireless client device to the encrypted router using a PIN or
the WPS buttons on each device.
To view the WPS settings, click Wireless then select WPS.
WPS
Enable or disable WPS.
WPS Current Status
Displays whether or not the
wireless security is configured.
Self Pin Code
An 8-digit PIN which is required
when configuring the router
for the first time in Windows 7 or Vista.
SSID
The name of the wireless network.
Authentication Mode
The current security settings for the
corresponding SSID (wireless network).
Passphrase Key
A randomly generated key created by
the router during the WPS process.
WPS via Push Button
Click “Start to Process” to activate WPS.
WPS via PIN
Enter the PIN of a wireless device click “Start to Process” to
activate WPS.
73
Configuring Client List
View the wireless devices currently connected to the router.
To view the Client List settings, click Wireless then select Client
List.
Interface
The type of network connected to the device.
MAC Address
The MAC address of device connected to network.
Signal
The signal strength of the device connected to the network.
Idle Time
The amount of time the connected device has not been active on
the network.
Click Refresh to refill the list with currently connected devices.
74
Chapter 6
Advanced Settings
75
Configuring Advanced Settings
Allows you to define the Advanced Settings available on the router.
WARNING! Incorrectly changing these settings may cause the device to stop functioning. Do not modify
the settings in this section without a thorough understanding of the parameters.
To view the Advanced settings, click Wireless then select Advanced.
Fragment Threshold
Enter the maximum size of a packet during data transmission.
A value too low could lead to low performance.
RTS Threshold
Enter the RTS threshold. If the packet size is smaller than the
RTS threshold, the router does not use RTS/CTS to send the
data packet.
Beacon Interval
Enter the beacon interval. This is the amount of time that the
router sets to synchronize the network.
Delivery Traffic Indication Message (DTIM) Period
Enter the DTIM period. The DTIM is a countdown period informing clients of the next point
of broadcast and multicast of messages over the network. Valid values are between 1 and 255.
N Data Rate
Select the N data rate. This is the rate in which the ESR Series Router will transmit data packets to wireless N compatible devices.
76
Channel Bandwidth
Select the channel bandwidth. The factory default is Auto 20/40MHz. The default setting provides the best performance by auto
selecting channel bandwidth.
Preamble Type
Select the preamble type. Long Preamble provides better LAN compatibility and Short Preamble provides better wireless performance.
CTS Protection
Select the type of CTS protection. Using CTS Protection can lower the data collisions between Wireless B (802.11b) and Wireless G
(802.11g) devices and lower data throughput.
Tx Power
Select the wireless signal strength level. Valid values are between 25% and 100%.
Click Apply to save the settings or Cancel to discard changes.
77
Setting Up Parental Controls
Offensive web content can be blocked when a parent specifies keywords. Parents can also limit Internet access within a specified
time and day, with a Schedule. A Policy is a rule profile which describes the keyword filter and Internet access schedule. Parents can
apply the policy to multiple users or Policy Members. The Parental Controls tool will screen policy members based on applied policies.
Note: By default, everyone is allowed to view all the contents
without any limitation and filter.
Configuring the Access Control List
To view the ACL settings, click Firewall then select ACL.
Viewing the Access Control List
To learn how to view existing access control list, refer to Viewing Parental Policies.
Adding a Control Policy
To learn how to create and add a policy to the access
control list, refer to Adding a Control Policy.
To view the Wizard settings,
click Parental Control then select Wizard.
Enable Parental Control (Access Control)
Click to enable Parental Control.
Add Policy
Click the button to add a new control policy to the
network.
Policy Table
Shows the control policies available on the network.
Click Apply to save changes or Cancel to discard them.
78
Adding a Control Policy
1. Enter a unique name for your policy in the Policy Name
text field.
The router provides a wizard to guide you through setting up a
new Access Control Policy.
To start the procedure, click the Add Policy button.
2. Click Prev to return to the previous screen, Next to continue
the procedure, or Cancel to stop the procedure.
3. Add target devices to the access control policy.
Click Next to continue the procedure or Cancel to stop the
procedure.
The procedure consists of the following steps:
79
To add a device to the Member List, follow these steps:
a. Click MAC or IP from the Filter Type option.
b. Click Add to show the add client dialog.
c. Enter the name of the device in the Device Name text field.
5. Setting up a schedule for the router services.
d. Enter either a MAC address or an IP address in the Address
field depending upon which filter type you chose.
e. Click the Add Device Button
to close the screen and
add the device to the Member List.
To set up a Service Schedule, follow these steps:
a. Select Allow from the Schedule option.
b. Click the days that the schedule will be active.
c. Enter the time period that the schedule will be active.
6. Click Prev to return to the previous screen, Next to continue
the procedure, Save to save the changes, or Cancel to stop
the procedure.
4. Click Prev to return to the previous screen, Next to continue
the procedure, Save to save the changes, or Cancel to stop
the procedure.
80
7. Setup a keyword and URL filter list.
10.Select Enable to save web access information to a log file or
Disable to ignore the information.
To set up a keyword/URL filter list, follow these steps:
a. Select Allow from the Filtering option.
b. Enter a keyword or URL in the URL/Keyword text field.
c. Click the Add button to add the filter to the list.
d. Repeat steps a through c for each filter.
11.Click Prev to return to the previous screen, Save to save the
changes, or Cancel to stop the procedure.
8. Click Enable Application Filter to filter software applications.
9. Click Prev to return to the previous screen, Next to continue
the procedure, Save to save the changes, or Cancel to stop
the procedure.
81
Viewing Parental Policies
Available parental control policies are shown in a table and each policy can be enabled or disabled, edited, and deleted.
To view the Web settings, click Parental Control then select Web Monitor.
Enable
Click to enable or disable the control policy.
Policy Name
Shows the control policy name.
Target Device
Shows the target device MAC address or IP address.
Schedule
Shows the control policy schedule.
Logged
Shows whether the control policy is storing
log information.
Modify
Edit a policy by clicking the Edit Button.
Delete a policy by clicking the Delete Button.
82
Guest Network
The Guest Network function enables you to offer Internet connectivity to visitors or guests while keeping other networked devices
(computers and hard drives) and sensitive personal or company information private and secure.
The Guest Network is controlled by the Wireless SSID function. When the Guest Network function is enabled, the Guest SSID can
only get the internet connection from WAN, but can not reach the client from the LAN port.
Enabling the Guest Network
To view the Selection settings, click Guest Network then select Selection.
Guest Network
Enable or Disable the Guest Network
function
Client Isolation
Guest clients are isolated and cannot
communicate with each other.
SSID
Choose a SSID for the Guest Network
used. The SSID can be defined from the Wireless setting page.
Click Apply to save the settings or Cancel to discard changes.
83
Configuring the DHCP Server Setting
The Guest Network SSID should be on a different subnet from the router’s DHCP server.
To view the DHCP Server Settings, click Guest Network then select DHCP Server Setting.
Router IP address
Define the router IP address
for the Guest network.
Default Subnet Mask
Define the Subnet Mask IP
address for the Guest
network.
Start IP
To define the Guest network DHCP server start IP.
End IP
To define the Guest network DHCP server end IP.
Click Apply to save the settings or Cancel to discard changes.
84
Viewing the DHCP Client List on the Guest Network
Shows the list of guest clients registered on the network.
To view the DHCP Client List settings, click Guest Network then select DHCP Client List.
DHCP Client Table
Shows the IP address,
MAC address, and
expiration time of each
of the registered clients
on the list.
IP Address
The IP address of the guest client.
MAC Address
The MAC address of the guest client.
Expiration Time
The time that the guest client’s DHCP address will expire and must be renewed.
Click Refresh to refresh the view of the list.
85
IPv6
There are several connection types to choose from: Auto Detection, Static IPv6, Autoconfiguration (SLAAC/DHCPv6), PPPoE, IPv6
in IPv4 Tunnel, 6to4, and Link-local. If you are unsure of your connection method, please contact your IPv6 Internet Service Provider.
Note: If you are using the PPPoE option, you will need to ensure that any PPPoE client software on your computers has been removed or
disabled.
Enabling IPv6 Settings
To view the Basic settings, click IPv6 then select Basic.
Before using or configuring the IPv6 protocol, or IPv6 passthrough, on an ESR Series Router you must enable it.
IPv6
Select enable to configure the IPv6 protocol on the router.
IPv6 Passthrough
Select enable to allow IPv6 passthrough functionality.
IPv6 must be disabled to enable this feature.
Click Apply to save the settings or Cancel to discard changes.
86
Viewing the IPv6 Connection Status
To view the Status information, click IPv6 then select Status.
IPv6 Connection Information
Shows the IPv6 connection type, the LAN IPv6 link-local address and the DHCP-PD.
LAN IPv6 Computers List
Shows a list of network computers and their IPv6 connection information.
87
Configuring Static IPv6
To view the Static IPv6 settings, click IPv6 then select Static IPv6.
Use Link-Local Address
Enable or disable LAN link-local address.
IPv6 Address
Enter the LAN (local) IPv6 address for the router.
Subnet Prefix Length
Enter the subnet prefix length.
Default Gateway
Enter the default gateway.
Primary IPv6 DNS Address
Enter the primary IPv6 DNS address.
Secondary IPv6 DNS Address
Enter the secondary IPv6 DNS address.
LAN IPv6 Address
Enter the LAN IPv6 address.
LAN IPv6 Link-Local Address
Enter the LAN IPv6 link-local address.
Router Advertisement Lifetime
Enter the IPv6 Address Lifetime (in minutes).
Enable Automatic IPv6 Address Assignment
Enable or disable automatic IPv6 address assignment.
Click Apply to save the settings or Cancel to discard changes.
Autoconfiguration Type
Enter the autoconfiguration type. (Default: SLAAC+RDNSS).
88
Setting Autoconfiguration
To view the Auto Configuration settings, click IPv6 then select Auto Configuration.
Obtain A DNS Server Address Automatically
Enable or disable obtaining a DNS server
automatically.
Primary IPv6 DNS Address
Enter the primary IPv6 DNS address.
Secondary IPv6 DNS Address
Enter the secondary IPv6 DNS address.
Enable DHCP-PD
Enable or disable DHCP-prefix delegation (PD).
LAN IPv6 Address
Enter the LAN IPv6 address.
LAN IPv6 Link-Local Address
Enter the LAN IPv6 link-local address.
Enable Automatic IPv6 Address Assignment
Enable or disable automatic IPv6 address assignment.
Autoconfiguration Type
Enter the autoconfiguration type. (Default: SLAAC+RDNSS)
Router Advertisement Lifetime
Enter the IPv6 Address Lifetime (in minutes).
Click Apply to save the settings or Cancel to discard changes.
89
Configuring PPPoE
To view the PPPoE settings, click IPv6 then select PPPoE.
Address Mode
Select Static if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic.
MTU
Maximum Transmission Unit - you may need to change the MTU
for optimal performance with your specific ISP. 1492 is the
default MTU.
IP Address
Enter the IP address (Static PPPoE only).
User Name
Enter your PPPoE user name.
Password
Enter your PPPoE password.
Verify Password
Retype the your PPPoE password.
Service Name
Enter the ISP Service Name (optional).
Reconnect Mode
Select either Always-on, On-Demand, or Manual.
Maximum Idle Time
Enter a maximum idle time during which the
Internet connection is maintained during inactivity.
To disable this feature, enable Auto-reconnect.
90
Obtain A DNS Server Address Automatically
Enable or disable obtaining a DNS server automatically.
Primary IPv6 DNS Address
Enter the primary IPv6 DNS address.
Secondary IPv6 DNS Address
Enter the secondary IPv6 DNS address.
Enable DHCP-PD
Enable or disable DHCP-prefix delegation (PD).
LAN IPv6 Address
Enter the LAN IPv6 address.
LAN IPv6 Link-Local Address
Enter the LAN IPv6 link-local address.
Enable Automatic IPv6 Address Assignment
Enable or disable automatic IPv6 address assignment.
Autoconfiguration Type
Enter the autoconfiguration type. (Default: SLAAC+RDNSS)
Router Advertisement Lifetime
Enter the IPv6 Address Lifetime (in minutes).
Click Apply to save the settings or Cancel to discard changes.
91
Configuring 6to4
To view the 6to4 settings, click IPv6 then select 6to4.
6to4 Address
Enter the 6to4 IP address.
Primary IPv6 DNS Address
Enter the primary IPv6 DNS address.
Secondary IPv6 DNS Address
Enter the secondary IPv6 DNS address.
LAN IPv6 Address
Enter the LAN IPv6 address.
LAN IPv6 Link-Local Address
Enter the LAN IPv6 link-local address.
Enable Automatic IPv6 Address Assignment
Enable or disable automatic IPv6 address
assignment.
Autoconfiguration Type
Enter the autoconfiguration type. (Default: SLAAC+RDNSS)
Router Advertisement Lifetime
Enter the IPv6 Address Lifetime (in minutes).
Click Apply to save the settings or Cancel to discard changes.
92
Viewing Local Connections
To view the Link Local settings, click IPv6 then select Link Local.
LAN IPv6 Link-Local Address
Enter the LAN IPv6 link-local address.
Click Apply to save the settings or Cancel to discard changes.
93
Firewall Setup
Note: This section applies to Client Router mode.
Configuring Basic Settings
To view the Basic settings, click Firewall then select Basic.
The ESR Series Router firewall automatically detects and blocks Denial of Service (DoS) attacks. URL blocking, packet filtering and
stateful packet inspection (SPI) are also supported. The details of the attack and the timestamp are recorded in the security log.
Firewall
Enable or disable the firewall of the ESR Series Router.
Click Apply to save the settings or Cancel to discard changes.
94
Configuring Advanced Settings
The router supports VPN pass-through which allows virtual private networking (VPN) packets to pass through the firewall.
To view the Advanced settings, click Firewall then select Advanced.
Note: VPN L2TP Pass-through, VPN PPTP Pass-through, and
VPN IPSec Pass-through are enabled by factory default.
VPN L2TP Pass-through
Click Select to allow an L2TP connection method
over a VPN.
VPN PPTP Pass-through
Click Select to allow a PPTP connection method
over a VPN.
VPN IPSec Pass-through
Click Select to allow an IPSec connection method over a VPN.
IPv6 Pass-through
Click Select to allow IPv6 packets to pass through the firewall.
PPPoE Pass-through
Click Select to allow a PPPoE packets to pass through the firewall.
Click Apply to save the settings or Cancel to discard changes.
95
VPN L2TP Pass-through Click Select to allow
an L2TP connection method over a VPN.
VPN PPTP Pass-through Click Select to allow a
PPTP connection method over a VPN.
VPN IPSec Pass-through Click Select to allow
an IPSec connection method over a VPN.
IPv6 Pass-through Click Select to allow IPv6
packets to pass through the firewall.
PPPoE Pass-through Click Select to allow
PPPoE packets to pass through the firewall.
Click Apply to save the settings or Cancel to discard changes.
Note: VPN L2TP Pass-through, VPN PPTP Pass-through, and VPN
IPSec Pass-through are enabled by factory default.
96
Configuring Demilitarized Zone
Configuring a device on the LAN as a Demilitarized Zone (DMZ) host allows unrestricted two-way Internet access for Internet
applications, such as online video games, to run from behind the NAT firewall. The DMZ function allows the router to redirect all
packets going to the WAN port IP address to a particular IP address on the LAN. The difference between the virtual server and the
DMZ function is that a virtual server redirects a particular service or Internet application, such as FTP, to a particular LAN client or
server, whereas a DMZ redirects all packets, regardless of the service, going to the WAN IP address to a particular LAN client or server.
A DMZ host allows a computer to have all its connections and ports completely open during data transmission.
WARNING! The PC defined as a DMZ host is not protected by the firewall and is vulnerable to malicious network attacks.
Do not store or manage sensitive information on the DMZ host.
To view the DMZ settings, click Firewall then select DMZ.
Enabling DMZ
Click Enable DMZ to activate DMZ functionality.
Local IP Address
Enter an IP address of a device on the LAN.
Click Apply to save the settings or Cancel to discard changes.
97
Configuring Denial of Service
To enable blocking of denial of service (DoS) attacks, select the DoS option in the Firewall section. DoS attacks can flood the Internet
connection with the continuous transmission of data. Blocking these attacks ensures that the Internet connection is always available.
To view the DoS settings, click Firewall then select DoS.
Block DoS
Enable or disable blocking DoS attacks.
Discard Ping on WAN
ICMP (ping) packages are blocked
while Block DoS is enabled.
Enable Discard Ping on WAN if the WAN port is required.
Click Apply to save the settings or Cancel to discard changes.
98
Virtual Private Network Setup
A Virtual Private Network (VPN) provides a secure connection between two remote locations or two users over the Internet. It
provides authentication to securely encrypt data communicated between the two remote endpoints. The Short Model Name supports
up to 5 VPN tunnels, making it ideal for small-office / home-office users or employees who work from home but need to communicate
securely back to the main office.
Viewing Status
To view the Status settings, click VPN then select Status.
No. (Number)
The sequence number of the VPN tunnel.
Name
The name of the VPN tunnel.
Type
The type of VPN tunnel.
Gateway/Peer IP Address
The VPN gateway or peer IP address.
Transmit Packets
The number of packets transmitted.
Received Packets
The number of packets received.
Uptime
The amount of time the VPN has been active.
Select
Indicates the device(s) that can have actions performed on them.
99
Configuring a VPN Tunnel Profile
To view the Status settings, click VPNthen select Status.
Manually configure a VPN tunnel profile.
Creating a Profile
•
•
•
•
Click Add to create a new VPN tunnel profile.
Click Edit to edit the settings of the selected profile.
Click Delete Selected to delete the selected profile.
Click Delete All to delete all current profiles.
100
General
For manually configuring a VPN tunnel profile.
Name: Enter the name for this profile.
Connection Type: Click the drop-down menu to select the
connection type (PPTP, L2TP, IPSec, L2TP over IPSec).
Authentication Type: Click the drop-down menu to select the
authentication type.
Shared Key: Enter the shared key to be used for this profile.
Confirm: Enter the shared key a second time to confirm the
shared key.
Local ID Type: Click the drop-down menu to select the type of
ID used for this profile (IP address, Domain Name, Email
Address).
Peer ID: Enter the Peer ID designation based on definition type
from Peer ID Type, previous field.
Apply: Click Apply to save the changes.
Cancel: Click Cancel to delete the changes.
Local ID: Enter the local ID designation based on definition type
from Local ID Type, previous field.
Peer ID type: Click the drop-down menu to select the type of
Peer ID for this profile (IP address, Domain Name, Email
Address).
101
SA (Security Association)
IKE (Internet Key Exchange) is configured in two negotiations.
Phase 1 authenticates the VPN Clients to each other by
confirming the matching Pre-Shared Key with the two gateways.
IPSec is the Phase 2 of the VPN process.
Manually configuring a VPN tunnel profile.
IKE (Phase 1) Proposal
Exchange: Click the drop-down menu to select the type of
exchange (Main Mode, Aggressive Mode).
DH Group: Click the drop-down menu to select the DH group
(group 1, group 2, group 5, group 14).
Encryption: Click the drop-down menu to select the type of
encryption (DES, 3DES, AES128, AES192, AES256).
Authentication: Click the drop-down menu to select the
authentication protocol (MD5, SHA1).
Authentication: Click the drop-down menu to select the
authentication protocol (MD5, SHA1).
Perfect Forward Secrecy (PFS): Select enable to enable PFS. A
fresh DH key is generated during IKE phase II and renewed for
each key exchange to eliminate dependencies between the
keys.
Life Time: Enter the life time value for Phase 1. The life time
value should be greater than Phase 2 (IPSec). 86400 sec. (1day)
is a common default and is a normal value for Phase 1.
IPSec (Phase 2) Proposal
Protocol: Click the drop-down menu to select the protocol type
(ESP, AH)
Encryption: Click the drop-down menu to select the type of
encryption (DES, 3DES, AES128, AES192, AES256).
DH Group: Click the drop-down menu to select the DH group
(group 1, group 2, group 5, group 14).
Life Time: Enter the life time value for Phase 2. The life time
value should be smaller than Phase 1 (IKE). 3600 sec. (1 hour)
is a common value for Phase 2.
Apply: Click Apply to save the changes.
Cancel: Click Cancel to delete the changes.
102
Network
Manually configuring a VPN tunnel profile.
Security Gateway Type: Click the drop-down menu to select the
Security Gateway Type (IP Address, Domain Name)
Security Gateway: Enter the gateway value as defined in
Security Gateway Type.
Local Network
Local Address: Enter the IP address of the local PC.
Local Netmask: Enter the netmaks of the local PC.
Remote Network
Remote Address: Enter the IP address of the remote PC.
Remote Netmask: Enter the netmask of the remote PC.
Apply: Click Apply to save the changes.
Cancel: Click Cancel to delete the changes.
103
Advanced
Manually configuring a VPN tunnel profile.
NAT Traversal: Select enable to enable the NAT Traversal
function in order to hide the private IP address from public view.
Note: Services such as VoIP require the use of a private
IP address.
Dead Peer Detection:
Apply: Click Apply to save the changes.
Cancel: Click Cancel to delete the changes.
104
Configuring a User Setting
The User Setting function allows you to create user profiles
inorder to setup login access to the VPN service.
Name
Enter the name of the new user profile.
Password
Enter the password for the user name.
Confirm
Enter the password a second time to confirm the setting.
Add
Click Add to accept the profile and add it to the Current VPN User
Table.
Reset
Click Reset to clear the new settings.
Current VPN User Table
Displays the User ID, User Name and Selection status.
Delete Selected
Click to delete the selected user profile.
Reset
Click to clear the selections from the Current VPN User Table.
Apply
Click to accept save the new settings.
Cancel
Click to clear the new changes.
Delete All
Click to delete all the current user profiles.
105
USB Port
The ESR1200 router is equipped with a USB port for connecting a hard drive so media content can be accessed or transferred to other
devices in the home or devices away from home.
Viewing EnShare
The EnShare feature allows you to access media
content stored on a USB hard drive connected to the
router’s USB port in the home and when you are away
from home when you have access to the Internet.
By default the EnShare feature is enabled.
To view the EnShare settings or disable EnShare, click USB Port then select EnShare.
1. Select Disable to disable the EnShare feature.
2. Click Apply to save the new settings.
File Sharing
The File Sharing function allows you to provide users
the ability to share files over the network through the
Samba service. By default the EnShare feature is
enabled.
To view the File Sharing settings, click USB Port then select File Sharing.
1. Select Enable to enable the Samba Service function.
2. Click Apply to save the new settings, or click Cancel to delete the changes.
106
Viewing File Server
The File Server function allows you to provide network users FTP access to shared USB stored files.
To view the File Server settings, click USB Port then select File Server.
Enable FTP Service
Select this to enable the FTP service to share files on the USB
device
Port Number
Define the port number (default: 21) to open for the FTP service.
Login Timeout
Define the period of inactivity (default: 90) before a user is
logged out.
Stay Timeout
Define the lockout period (default: 90) before a user is allowed
to attempt a login.
Login User
Define the number of concurrent users to access the service
(Max: 20 users)
Share Mode
Define the type of share priviledge: Read/Write, Read only.
Use Anonymous Login
Select this to allow anonymous user login.
User Name
Enter the user name to login to the FTP service.
Password
Enter the password to login to the FTP service.
107
Viewing DLNA
The DLNA Media Server function allows you to transfer photos, music and video between networked devices through the ESR Series
Router.
To view the DLNA settings, click USB Port then select DLNA.
1. Select Enable to enable the DLNA Media Server function.
2. In the Share Folder Name, enter the name of the shared folder.
3. Click Apply to save the new settings, or Cancel to clear the changes.
108
Advanced Network Settings
NAT Setup
Network Address Translation (NAT) allows users on the LAN to access the Internet through a single Public IP Address or multiple
Public IP Addresses. NAT provides firewall protection from hacker attacks and allows for mapping LAN IP addresses to WAN IP
addresses with key services such as websites, FTP, and video game servers.
To view the NAT settings, click Advanced then select NAT.
NAT
Enable or Disable the NAT.
Network Turbine
Enable or Disable the network turbine.
Note: The network turbine is designed to improve the router’s performance. There is about 20~30% improvement when the
network turbine is enabled.
Note: The network turbine may cause problems with the Internet connection. Disable the network turbine function if you experience
connection issues.
Click Apply to save the settings or Cancel to discard changes.
109
Port Mapping Setup
Port Mapping allows you to redirect a particular range of service port numbers from the WAN to a particular LAN IP address.
To view the Port Mapping settings, click Advanced then select Port Mapping.
Enable Port Mapping
Click Enable Port Mapping to activate port mapping.
Description
Enter notes or details about the mapped port range
configuration.
Local IP
Enter the local IP address of the server behind the
NAT firewall.
Protocol
Select the protocol to use for mapping from the following: TCP, UDP or Both.
Port Range
Enter the range of ports to be forwarded.
Click Add to append a new device to the list or Reset to discard changes.
110
Current Port Mapping Table
Displays a list of mapped port ranges in use on the network.
No. (Number)
The sequence number of the mapped port range.
Description
Notes or details about the mapped port range.
Local IP
IP address of the server for the mapped port range.
Type
The protocol used to communicate with the WAN ports and LAN
server.
Port Range
The range of mapped ports.
Select
Indicates the device(s) that can have actions performed on them.
Click Delete Selected to remove selected devices from the list.
Click Delete All to remove all devices form the list.
Click Reset the discard changes.
Click Apply to save the settings or Cancel to discard changes.
111
Port Forwarding Setup
Port forwarding enables multiple server applications on a LAN to serve clients on a WAN over a single WAN IP address. The router
accepts incoming client packets, filters them based on the destination WAN, or public, port and protocol and forwards the packets to
the appropriate LAN, or local, port. Unlike the DMZ feature, port forwarding protects LAN devices behind the firewall.
To view the Port Forwardung settings, click Advanced then select Port Forwarding.
Enable Port Forwarding
Click Enable Port Forwarding to active port forwarding.
Description
Enter notes or details about the forwarded port configuration.
Local IP
Enter the local IP address of the server behind the NAT firewall.
Protocol
Select the protocol to use for mapping from the following: TCP,
UDP or Both.
Local Port
Enter the LAN port number that WAN client packets will be
forward to.
Public Port
Enter the WAN port number that clients will send their packets
to.
Click Add to append a new configuration to the table or Reset
to discard changes.
112
Current Port Forwarding Table
The table of current port forwarding configurations.
Click Delete Selected to remove selected devices from the list.
Click Delete All to remove all devices form the list.
Click Reset the discard changes.
Click Apply to save the settings or Cancel to discard changes.
113
Port Triggering Setup
Some applications, such as online games, videoconferencing and VoIP telephony, require multiple ports for inbound and outbound
traffic. If an application requires simultaneous use of incoming and an outgoing ports, configure port triggering to map a local port or
range of ports to a specific public port. Sending packets out over the local port triggers the router to open an incoming local port that
is mapped to the same public port and application as the outgoing local port(s). The local application can communicate over the
incoming and outgoing ports without the need for creating a fixed address.
To view the Port Triggering settings, click Advanced then select Port Triggering.
Enable Port Triggering
Click Enable Trigger Port to activate port triggering.
Description
Enter notes or details about the port triggered configuration.
Popular Applications
Select a default application or add a new one.
Trigger Port
Enter the application’s outbound port number(s).
Trigger Type
Select the protocol to use for port triggering from the following:
TCP, UDP or Both.
Public Port
Enter the inbound port(s) for the application in the following
format: 2300-2400 or 47624.
114
Public Type
Select the protocol to use for the inbound port from the following: TCP, UDP or Both.
Click Add to append a new configuration to the table or Reset to discard changes.
Current Port Triggering Table
The list of current port triggering configurations.
Click Delete Selected to remove selected devices
from the list.
Click Delete All to remove all devices form the list.
Click Reset the discard changes.
Click Apply to save the settings or Cancel to discard changes.
115
Application Layer Gateway Setup
The ALG (Application Layer Gateway) serves as a window between correspondent application processes so that they may exchange
information on an open environment.
To view the ALG settings, click Advanced then select ALG.
Select the listed applications that need ALG support and then the router will authorize them to pass through the NAT gateway.
Click Apply to save the settings or Cancel to discard changes.
116
Universal Plug and Play Setup
UPnP helps internet devices, such as gaming and videoconferencing, to access the network and connect to other registered UPnP
devices.
To view the UPnP settings, click Advanced then select UPnP.
Click Enable or Disable to activate or deactivate UPnP.
Click Apply to save the settings or Cancel to discard changes.
117
Internet Group Multicast Protocol Setup
Internet Group Multicast Protocol (IGMP) is a network-layer protocol used to establish membership in a multicast group.
To view the IGMP settings, click Advanced then select IGMP.
Click Enable or Disable to activate or deactivate IGMP.
Click Apply to save the settings or Cancel to discard changes.
Note: Disabling the Multicast function may cause IP based multimedia devices, such as an IP-STB or OTT box, may lose
connectivity with the media streaming server.
118
Quality of Service Setup
QoS can prioritize bandwidth use such as video streaming, online gaming, VoIP telephony and videoconferencing to ensure stable
and efficient network performance.
To view the QoS settings, click Advanced then select QoS.
Total Bandwidth Settings
Uplink Select the maximum bandwidth speed for outbound
traffic.
Downlink Select the maximum bandwidth speed for inbound
traffic.
Note: Click Disabled if you do not want to prioritize any data or protocol.
119
Priority Queue
Set network resource usage based on specific protocols or port ranges. Incoming packets are processed based on the protocols’
position within the queue.
Unlimited Priority Queue
Local IP Address
Enter the local IP address of a device on the network.
This device’s activity is not restricted by the QoS feature.
High/Low Priority Queue
Specify the priority for different protocols. Additional
protocols and port ranges can be added.
Click Apply to save the settings or Cancel to discard
changes.
120
Bandwidth Allocation
Set network resource usage, for inbound and outbound traffic, based on local IP and port ranges.
Type
Select Download or Upload to specific the direction of packet
traffic.
Local IP Range
Enter the local IP range of the current configuration.
Protocol
Select the protocol to manage for the current configuration.
Port Range
Enter the local port range of the current configuration.
Policy
Select Min or Max to specify the type of configuration policy.
Rate (bps)
Select the bandwidth rate, in bits per second (bps), of the current configuration.
Click Add to save the settings and list the configuration in the
Current QoS table or Reset the discard changes.
Click Apply to save the settings or Cancel to discard changes.
121
Routing Setup
Typically static routing does not need to be setup because the router has adequate routing information after it has been configured
for Internet access. Static routing is only necessary if the router is connected to network under a different subnets.
To view the Routing settings, click Advanced then select Routing.
Note: To enable a static routing, NAT must be disabled.
If the router is connected with a network under the different
subnet, the routing setup allows the network connection within
two different subnets.
Enable Static Routing
Click Enable Static Routing to activate the feature.
Destination LAN IP
Enter the LAN IP address of the destination device.
Subnet Mask
Enter the Subnet Mask of the destination device.
Default Gateway
Enter the default gateway IP address for the destination device.
Click Add to save the settings and list the configuration in the
Current Static Routing table or Reset the discard changes.
View and select devices in the Current Static Routing Table.
Click Delete Selected or Delete All to remove devices
from the table. Click Reset to stop.
Click Apply to save the settings or Cancel to discard changes.
Hops
Enter the maximum number of hops within the static routing
that a packet is allowed to travel.
Interface
Select LAN or WAN as the interface.
122
Wake on LAN Setup
Wake on LAN setup (WOL) allows the administrator to activate a computer over the network.
To view the WOL settings, click Advanced then select WOL.
Enabling WOL over WAN
Click Enable WOL over WAN to activate the feature.
Server Port
Enter the server port of the device to activate.
Wake MAC Address
Enter the MAC address of the device to activate.
Click Start to activate the device.
Click Apply to save the settings or Cancel to discard changes.
123
Tools Setup
Configuring the Administrator Account
Change the router’s system password as well as setup a device
to remotely configure the settings.
To view the Admin settings, click Tools then select Admin.
•
•
•
•
•
Login Name: Keep or change existing login name
Old Password: Enter the existing administrator password
New Password: Enter the new administrator password
Repeat New Password: Re-type the new administrator password
Graphical Authentication: To enable or disable CAPTCHA
Remote Management
• Host Address: Enter the designated host IP Address.
• Port: Enter the port number (Default: 8080) for remote accessing
management web interface.
• Enable: Select to enable remote management.
Click Apply to save the settings or Cancel to discard changes.
Note: To access the settings of the ESR Series Router remotely,
enter the router’s WAN IP address and port number.
124
System Time Setting
Change the system time of the ESR Series Router and setup automatic updates through a network time (NTP) protocol server or
through a computer.
To view the Time settings, click Tools then select Time.
Synchronizing with an NTP Server
Time Setup
Select how the ESR Series Router obtains
the current time.
Time Zone
Select the time zone for the ESR Series Router.
NTP Time Server
Enter the domain name or IP address of an NTP server.
Enabling Daylight Savings
Click to enable or disable daylight savings time.
Start Time
Select the date and time when daylight savings time starts.
End Time
Select the date and time when daylight savings time ends.
Click Apply to save the settings or Cancel to discard changes.
125
Synchronizing Time with a Computer
Time Setup
Select how the ESR Series Router obtains the current time.
Computer Date and Time
Displays system date and time from a computer.
Enable Daylight Saving
Click to enable or disable daylight savings time.
Start Time
Select the date and time when daylights
savings time starts.
End Time
Select the date and time when daylights savings time ends.
Click Apply to save the settings or Cancel to discard changes.
126
Dynamic Domain Name Service (DDNS) Setup
The most common use for DDNS is in allowing an Internet domain name to be assigned to a computer with a varying (dynamic) IP
address. This makes it possible for other sites on the Internet to establish connections to the machine without needing to track the IP
address themselves.
To view the DDNS settings, click Tools then select DDNS.
Dynamic DNS
Click to enable or disable DDNS.
Server Address
Select the server address.
Host Name
Enter the host name.
Username
Enter a username for the host service.
Password
Enter a password for the host service.
Click Apply to save the settings or Cancel to discard changes.
127
Diagnosis that Client Devices Are Connected to the Router
The diagnosis feature allows the administrator to verify that a client device is available on the network and is accepting request
packets. If the ping result returns alive, it means a device is connected. This feature does not work if the target device is behind a
firewall or has security software installed.
To view the Diagnosis settings, click Tools then select Diagnosis.
Diagnosing a Network Connection Problem
Address to Ping
Enter IP address of the device to ping.
Ping Frequency
Select the interval, in seconds, that the ping message is sent out.
Click Start to begin the diagnosis.
128
Upgrading The Router’s Firmware
Firmware is the router’s system software that operates and allows the administrator to interact with it.
To view the Firmware settings, click Tools then select Firmware.
WARNING! Upgrading firmware through a wireless connection is not recommended. Firmware upgrading must be performed while connected
to an Ethernet (LAN port) with all other clients disconnected.
To update the firmware version, follow these steps:
1. Download the appropriate firmware approved by EnGenius from an EnGenius web site. See the Downloads tab on the product
page for this product. For new products, new firmware may not be readily available.
2. Click Choose File.
3. Browse the file system and select the firmware file.
4. Click Apply.
129
Backing Up The Router’s Settings
Save them as a configuration file on your computer.
To view the Back-up settings, click Tools then select Back-up.
Restoring to the router’s Factory Default settings
Click Reset to restore the ESR Series Router to factory defaults.
Backup Settings
Click Save to save the current configuration on the router to a *.dlf file.
Restore Settings
To restore saved settings, do the following:
a. Click Choose File.
b. Browse the file system for location of the settings file (*.dlf).
c. Click Upload.
130
Rebooting the Router
This feature allows you to reboot the router in the event of a system hang up or other disruption to the network.
To view the Reset settings, click Tools then select Reset.
Click Apply to reset the device.
131
Appendix
132
Wall Mounting The Router
The following are instructions if you choose to mount the router on a
wall.
Note: Choose a location that is within reach of an electrical
outlet for the AC adapter and the DSL or Cable modem.
To mount the device on the wall do the following:
1. Measure the distance from the middle of each mounting screw hole.
2. Mark the locations of the screw holes on the wall.
3. Drill a hole for each marked location and insert a screw in each.
Note: Make sure to leave enough of the screw head above
the wall surface to secure the router.
4. Install and secure the mounts onto the router.
5. Install the router on the wall.
133
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.155.25GHz band are restricted to indoor usage only.
IMPORTANT NOTE:
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
134
Industry Canada Statement
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d’Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement
est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these
radars could cause interference and/or damage to LE-LAN devices.
Avertissement:
(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à l’intérieur afin de réduire
les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
(c.-à-d., qu’ils ont la priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/
ou des dommages aux dispositifs LAN-EL.
FOR MOBILE DEVICE USAGE
Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Déclaration d’exposition aux radiations: Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source
135
de rayonnement et votre corps.
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been
applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
• EN60950-1
Safety of Information Technology Equipment
• EN50385
Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human
exposure to electromagnetic fields (0 Hz - 300 GHz)
• EN 300 328
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating
in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article
3.2 of the R&TTE Directive
• EN 301 893
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering essential requirements of article 3.2
of the R&TTE Directive
• EN 301 489-1
Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 1: Common technical requirements
• EN 301 489-17
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and
services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
136
This device is a 5GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries,
except in France and Italy where restrictive use applies.
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device
for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.
This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10
mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum
authority in France.
Česky [Czech]
[Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými
ustanoveními směrnice 1999/5/ES.
Dansk [Danish]
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Deutsch [German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti [Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust
direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
Español [Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales
y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
Ελληνική [Greek]
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ΔΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ
ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
137
Français [French]
Par la présente [nom du fabricant] déclare que l’appareil [type d’appareil] est conforme aux exigences essentielles et aux
autres dispositions pertinentes de la directive 1999/5/CE.
Italiano [Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle
altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Latviski [Latvian]
Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas
1999/ 5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.
Lietuvių [Lithuanian]
Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB
Direktyvos nuostatas.
Nederlands [Dutch]
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen
en de andere relevante bepalingen van richtlijn 1999/5/EG.
Malti [Maltese]
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti
oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Magyar [Hungarian]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC
irányelv egyéb elõírásainak.
Polski [Polish]
Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi
stosownymi postanowieniami Dyrektywy 1999/5/EC.
Português [Portuguese]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Slovensko [Slovenian]
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive
1999/5/ES.
Slovensky [Slovak]
[Meno výrobcu] týmto vyhlasuje, že [typ zariadenia] spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice
1999/5/ES.
Suomi [Finnish]
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on
direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Svenska [Swedish]
Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och
övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
138

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Annotate, Fill forms
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2013:11:14 10:56:51-08:00
Metadata Date                   : 2013:11:18 09:47:58+08:00
Modify Date                     : 2013:11:18 09:47:58+08:00
Creator Tool                    : Adobe InDesign CS6 (Macintosh)
Instance ID                     : uuid:1cc69f1d-79dc-4416-87f4-1b72f145fa91
Original Document ID            : xmp.did:6EDAF4D6192068118083B95EF467C178
Document ID                     : xmp.id:4B5365BE0C20681180838C7D08E992B4
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:4A5365BE0C20681180838C7D08E992B4
Derived From Document ID        : xmp.did:DAFC491211206811822ADB4C9F810D41
Derived From Original Document ID: xmp.did:6EDAF4D6192068118083B95EF467C178
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Macintosh)
History Changed                 : /
History When                    : 2013:11:14 10:56:51-08:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 138
Creator                         : Adobe InDesign CS6 (Macintosh)

EXIF Metadata provided by EXIF.tools

EnGenius Technologies ESR1200 Dual Band Wireless AC1200 Router User Manual

EnGenius Technologies Dual Band Wireless AC1200 Router

User Manual.pdf

FCC ID Filing: A8JESR1200

Navigation menu

Namespaces

Views

Navigation