EnGenius Technologies SP935 Long Range Cordless SIP Phone System User Manual SP 935 Jan292015

Download:
Mirror Download [FCC.gov]
Document ID	2519641
Application ID	puzpIzoZLoEwsAQ1e0oaIQ==
Document Description	User Manual_rev.pdf
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	134.61kB (1682661 bits)
Date Submitted	2015-01-30 00:00:00
Date Available	2015-01-30 00:00:00
Creation Date	2015-01-30 11:16:53
Producing Software	GPL Ghostscript 9.04
Document Lastmod	2015-01-30 11:16:53
Document Title	SP-935_User Manual_Jan292015
Document Creator	PDFCreator Version 1.2.3
Document Author:	aihsu

Table of Contents
User Manual
SP-935
Digital Long Range Cordless Phone
EnGenius Customer Service
http://www.engeniustech.com/
Safety Instructions ....................................................................................5
General Safety Instructions ...................................................................5
Product Safety Instructions ...................................................................5
Battery Safety Instructions ....................................................................7
Regulatory Information .............................................................................8
Equipment Checklist ............................................................................... 11
Handset Illustration................................................................................. 12
Handset Features .................................................................................... 13
Basic Handset Features ....................................................................... 13
Additional Handset Features ............................................................... 15
Base Illustration ...................................................................................... 21
Base Features.......................................................................................... 22
Basic Base Station Features ................................................................. 22
Charger Illustration ................................................................................. 23
Charger Features..................................................................................... 24
Getting Started ....................................................................................... 25
Base Station Installation...................................................................... 25
Handset and Charger Installation ........................................................ 26
Basic Operations ..................................................................................... 27
Operation Modes ................................................................................ 27
A. Base Operation Modes................................................................ 27
B. Handset Operation Modes .......................................................... 27
Making a Telephone Call ..................................................................... 29
Making an 2-Way/ Intercom Call ......................................................... 29
Making a Broadcast ............................................................................ 30
Handset to Handset Calls ................................................................ 30
Redial ................................................................................................. 31
Receiving a Telephone Call .................................................................. 31
Receiving an Intercom Call .................................................................. 32
Ending a Call ....................................................................................... 33
Adjusting Handset Receiver (Earpiece) Voice Volume.......................... 33
Adjusting Handset Speakerphone Voice Volume ................................. 33
Placing a Call On Hold ......................................................................... 33
Mute................................................................................................... 34
Do Not Disturb (Silent Ring) ................................................................ 34
Key Guard ........................................................................................... 34
~2~
Battery Recharge and Replacement .................................................... 35
Advanced Operations .............................................................................. 36
Handset Registration .......................................................................... 36
Handset Group Subscription ............................................................... 37
Call Transfer........................................................................................ 38
Phonebook Operations ....................................................................... 39
Programmable Feature Call................................................................. 43
Caller ID .............................................................................................. 44
Call Manager....................................................................................... 46
Incoming ............................................................................................. 46
Outgoing ............................................................................................. 47
Call Barring ......................................................................................... 47
Visual Message Waiting Indicator (VMWI)........................................... 48
Adjust Handset Microphone Gain ....................................................... 49
Adjust Headset Ring ............................................................................ 49
SIP Configuration .................................................................................... 50
Introduction........................................................................................ 50
Application ......................................................................................... 50
VoIP Features ..................................................................................... 50
Registration handsets ......................................................................... 50
Default settings .............................................................................. 51
Web configuration .......................................................................... 51
LAN configuration ........................................................................... 52
Base Settings .................................................................................. 53
SIP Configuration ................................................................................ 53
SIP server........................................................................................ 53
SIP account ..................................................................................... 53
Individual account .......................................................................... 54
Audio Setting .................................................................................. 55
Tools ................................................................................................... 56
Admin ............................................................................................. 56
Time ............................................................................................... 57
Diagnosis ........................................................................................ 57
Firmware ........................................................................................ 58
Back-up .......................................................................................... 58
Reset/ReBoot/Registration ............................................................. 58
Menu Operations .................................................................................... 60
Technical Specifications .......................................................................... 66
~3~
Base Station ............................................................................................ 68
Index....................................................................................................... 73
~4~
manufacturer will void the warranty and the FCC authorization to operate the
equipment. Use only manufacturer provided accessories.
Safety Instructions
Caution: Your wireless telephone gives you freedom and flexibility to
stay in touch while you move around. However, when using your phone
equipment, safety instructions should be followed to avoid the risks of
fire, electric shock, injury to person, and damage to property.
General Safety Instructions
1. When using your wireless phone, ensure your safety and the safety of others:
4.
Do not use the telephone near water. Never spill liquid of any kind on this
product.
5.
Unplug the product from the wall telephone jack and power outlet before
cleaning. Do not use liquid or aerosol cleaners. Use damp cloth for cleaning.
6.
Do not place this product on an unstable cart, stand, or table. The product may
fall and cause personal injury or damage to the product or other property.
7.
Power Outage: In the event of a power outage, your handset charger will not
recharge the handset battery, and the base station will not allow you to make
an outgoing call or take an incoming call. Both the charger and the base station
require electricity for operation. You should have a telephone that does not
require electricity available for use during power outage, or have a temporary
backup power supply.
8.
Slots or openings in the product’s housing are provided for ventilation. These
openings must not be blocked or covered. Placing the product on a bed,
carpeting, or other similar surface may block these openings and should be
avoided. This product should never be placed near or over a radiator or heat
register, or in a built-in installation unless proper ventilation is provided.
9.
Never push objects of any kind into this product through housing
slots/openings as they may damage the product, touch dangerous voltage
points or short out parts that could result in fire, electric shock, or injury.
a. Always watch where you are walking and standing.
b. Don’t let a phone call distract you from working safely.
c.
If power goes out, it won’t work. Recommend backup power.
2. In an emergency:
a. If an emergency occurs, dial the emergency phone number. Remember: if
you are in an area where your phone does not have a clear signal from the
base, it is highly probable that the call may not go through. Locate the
nearest landline telephone or other communications device to call for help.
b. Emergency calls may not automatically provide emergency personnel with
your name, phone number or location.
3. Notice to Hearing Aid Users: This phone system is compatible with inductively
coupled hearing aids.
4. Notice to Cardiac Pacemaker Users: Preliminary studies done by the US FDA
and others have shown that, although interference to the implanted cardiac
pacemaker may occur when operating very closely, wireless telephones “do not
seem to pose a significant problem for pacemaker wearers.” However, until
more is known, FDA suggests that people with pacemakers may want to take
precautions when using or carrying a wireless telephone to ensure that there is
ample distance between the telephone and the pacemaker. Do not carry the
handset in a breast pocket. If you have any reason to suspect that interference
is taking place, turn off your handset immediately.
10. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supply to your
home, consult your dealer or local power company.
11. Do not overload wall power outlets and extension cords as this may result in
fire or electric shock.
12. To avoid electric shock or burn, do not disassemble this product. Send this
product to an authorized service center when service or repair work is required.
Call Customer Service for locations near you. Opening or removing covers may
expose you to dangerous voltages, electrical currents or other risks. Incorrect
reassembling of the product may cause electric shock when the product is
subsequently used.
13. Avoid using the product during a storm. There may be a risk of electric shock
from lightning.
Product Safety Instructions
Read and understand all instructions.
14. Do not place the product where persons can step, trip, or fall on it.
2.
Follow all warnings and instructions including those marked on the product.
15. Do not place conductive objects over or near the antenna.
3.
Changes or modifications to this product not expressively approved by the
16. Do not use the product to report a gas leak while in the vicinity of the leak.
1.
~5~
~6~
17. Do not install the base station or the handset charger near microwave ovens,
radios, TV sets, speakers, or other electrical equipment. These appliances may
cause interference to the product or experience interference from the product.
18. Unplug the base station or the charger adaptor from the power outlet and refer
to an authorized service center under the following conditions:
a.
b.
c.
d.
e.
f.
If liquid has been spilled into the product.
When the power supply cord or plug is damaged or frayed.
If the product has been exposed to rain or water.
If the product does not operate normally by following the operating
instructions.
If the product has been dropped or housing has been damaged.
If the product shows a distinct change in performance.
Regulatory Information
SP-935
FCC ID: A8J-SP935
IC: 10103A-SP935
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including
interference that may cause undesired operation.
Privacy of communications may not be ensured when using this phone.
Battery Safety Instructions
1.
Use only manufacturer approved Li-ion rechargeable batteries and charger. Do
not use other types of rechargeable batteries or non-rechargeable batteries.
The batteries could short-circuit, and the battery enclosure may be damaged
causing a hazardous condition.
2.
Follow the charging instruction in this manual and instruction labels and
markings in the handset and charger compartments.
3.
Battery must be recycled or disposed of properly. Do not dispose the battery in
a fire. The cells may explode.
4.
Do not dispose of the battery in municipal waste. Check with local codes for
disposal instructions.
5.
Exercise care in handling the batteries in order not to short-circuit the battery
with conductive materials such as rings, bracelets, keys, pocketknife, and coins.
The battery or conductive material may overheat and cause burn or fire.
6.
Do not expose batteries to rain or water.
7.
Do not open or mutilate the battery. Released electrolyte is corrosive and may
cause injury to eyes or skin. The electrolyte may be toxic if swallowed.
8.
During charging, the battery heats up. This is normal and is not dangerous.
Base Station
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
~7~
~8~
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum
gain of 2 dBi. Antenna having a higher gain is strictly prohibited per regulations
of Industry Canada. The required antenna impedance is 50 ohms.
Portable Handset
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
~9~
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with FCC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. To maintain compliance
with IC RF exposure compliance requirements, please follow operation
instruction as documented in this manual.
This device has been designed to operate with an antenna having a maximum
gain of 2.5dBi. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.
~10~
Equipment Checklist
1.
Handset Illustration
In a Base + Handset package, please find the following components:
a. Base Station x 1 (antenna installed)
b. Base AC/DC Adaptor x 1
c. Handset x 1 (antenna installed)
d. Handset Antenna x 1 (Long ×1)
e. Desktop Charger x 1
f. Charger AC/DC Adaptor x 2
g. 1700mA Li-ion Battery Pack x 1
h. Telephone Cord x 1
i. CD (User’s Manual), Quick Guide
Antenna
Belt Clip
Holder
Receiver
4-line LCD
2.
In a Handset package, please find the following components:
a. Handset x 1 (antenna installed)
b. Handset Antenna x 1 (Long ×1)
c. 1700mA Li-ion Battery Pack x 1
d. Desktop Charger x 1
e. Charger AC/DC Adaptor x 1
f. Quick Guide
Volume control /
Scrolling
Broadcast key
END & Power
ON/OFF key
2-WAY/
INTERCOM
3.
Optional Accessory
a. Outdoor Antenna Kit (including antenna and cable)
b. High-gain handset antenna
c. Headset
TALK/FLASH/
(For PRO)
KEYLOCK/
(For Walkie)
Microphone
Battery pack
Travel charger jack
Headset jack
(2.5mm)
~11~
~12~
Handset Features
Basic Handset Features
1.
2.
4-line LCD (Liquid Crystal Display)
a. The LCD display has LED (Light Emitting Diode) for backlighting.
st
b. The 1 line of LCD consists of icons.
c. Icons explanation from left to right
(1)
(2)
(3)
RSSI level (Receive Signal Strength Indicator)
During a call, the number of bars is proportional to
the radio signal strength received.
Link mode
(2.1) Call in-progress (ON/OFF-Hook)
Indicates if the phone line is in the OFF-Hook status.
(2.2) Intercom in-progress
Indicates if Intercom mode is active
Indicate the Handset ID which is making intercom with.
Line, Sound and Indication
(3.1) Line Indicator
Indicate when using line 1 or the incoming call from FXO line
(3.2) SIP Indicator
Indicate when using SIP or the incoming call from SIP
(3.3) Enable ringer
Re:
3.
4.
(5)
11
(6)
nd
rd
d. The 2 and 3 lines of the LCD, maximum 16 characters each, display
status, message, menu selections, or user-editable alphanumerical
characters.
~13~
TALK/FLASH (
a. Places or answers a telephone or intercom call
b. Sends a Flash signal to phone line to retrieve a dial tone after the call ends,
or to perform the call waiting feature provided by local phone companies
during a call.
SPEAKERPHONE (
Press and hold the key for over 2 seconds to enable/disable the speakerphone
during incoming, outgoing or intercom call.
2-WAY INTERCOM ((
))
a. Places an intercom call to another handset, a group handset (group paging)
or all registered handsets.
b. Intercom calls are digital, full duplex, and are conducted without the
assistance from the base station.
6.
BROADCAST (
a. Half duplex broadcasting to handsets for immediate announcement
b. Half duplex broadcasting to base stations
(3.6) Vibrate mode
(4.2) Speaker indicator
Indicate if the speaker phone is active
Two-Digit Handset ID
Displays the 2-digit Handset ID of own.
Battery Strength
Number of bars is proportional to the amount of battery time remaining.
Single beep: successful key entry.
Double beep: indicates power on/off.
Triple beep: failed operation.
Periodic 1-Long-2-Short beep (every 1 minute): low battery warning、out of
range、call on hold
No any beep for invalid key entry
5.
(3.5) Ringer and vibrate mode
(3.7) Message waiting indicator
Disable PA and indicate speaker phone
(4.1)Indicate if the incoming broadcast is disabled.
Ringer
a. Rings to an incoming call and intercom call.
b. Distinctive alert sounds indicating various events:
(1)
(2)
(3)
(4)
(3.4) Disable ringer
(4)
The last line displays the left and right soft keys.
Re：Press the
broadcast function.
7.
key on the left top corner of handset to activate the
Left/Right Soft Keys (
a. Make menu selection.
~14~
8.
) /Down(
) Scrolling Keys
Up(
a. Scroll through records and menu selections.
b. Adjust receiver voice volume when in the Talk mode.
c. Press
to enter received call log when in the Standby mode.
d. Press
9.
6.
DND (Do Not Disturb, i.e., Silent Ring)
7.
Call Logs
a. Redial: Stores 10 phone numbers (up to 26 digits each) dialed most
recently. Can perform last-number redial on all 10 numbers.
b. Received & New Call Log: Total 50 entries (16-digit phone number, 16character names, and Date/Time stamp), needs Caller ID service from local
telephone company.
c. Phone numbers and names can be saved into phonebook while in display.
8.
Call Manager: Include blocking incoming call, outgoing call and assign line
dedication, line selection.
to enter phonebook when in the Standby mode.
END; On/Off Key (
a. Ends a call.
b. Leaves current menu operation, up one level.
c. Press for 3 seconds to off the power
Additional Handset Features
1.
Multiple handsets registration
a. Up to 10 handsets can be registered to a base station
b. ID 10-19: individual Handset IDs.
c. ID 1~7: Group IDs. Handsets can “subscribe” from the handset menu to
group(s) and be paged when a landline caller or an intercom caller enters a
Group ID.
2.
Ringer Vibrator
a. Two options for Line (incoming call) ringing & Intercom ringing.
b. Six-level ringer volume selections (Off/Low/Medium/High/Vibrate/ Vibrate
& High) for each option.
c. Eight ringer type selections for each option.
3.
Caller ID
Displays incoming call phone number and name on the LCD (needs Caller ID
service from local telephone company)
4.
Call waiting with caller ID
nd
st
Displays 2 incoming call information on the same phone line when 1 call is in
progress (needs Call Waiting with Caller ID service from local telephone
company)
5.
Name tagging with caller ID
Match the caller ID with the phone book entries; once matched, the LCD screen
will display the name or nickname instead of pure caller ID info (needs Call
Waiting with Caller ID service from local telephone company).
~15~
a.
Incoming call:
a-1. PA On/Off: Enable or disable the broadcast from other handsets or
base station. When PA is Off, the handset can’t receive broadcast from
base station or other registered handsets, but it can broadcast to base
station or other registered handsets.
a-2.. Line On/Off: Enable or disable the capability to receive incoming call
from telephone line/SIP call. When Line is Off, the handset can’t receive
incoming call from telephone line/SIP call, but it can still make outgoing
call.
a-3. Int. On/Off: Enable or disable the intercom from other handsets or
base station. When Int. is Off, the handset can’t receive intercom from
base station or other registered handsets, but it can intercom to base
station or other registered handsets.
Outgoing call
Select the mode of line selection (Auto/Manual/Predefine line/Off) when
you make a line call.
b-1. Auto: A handset will be selected one of available line from subscribed
bases before making an outgoing call. (Default)
b-2. Manual: A handset will be set prompted a select from a list of
~16~
available lines before making an outgoing call.(1 for telephone line, 5 for
SIP call)
b-3 Off: Disable the capability to make an outgoing call.
c.
Call Barring
c-1. Block the users from dialing long distance calls or international calls
c-2. Up to 5 digits of each call barring setting; up to 5 entries allowed
d. This changing requires to entering the “Call Settings” (MENU-4-3-4).
[Note] You need to key in the accurate user ID and password to perform this
feature. The default password is “0000”.
9.
Any Key Answer (except
and SILENT soft Key)
a If you enable Any Key Answer, while you have two incoming line calls
simultaneously, you can press 1 to answer the line 1 call or press 2 to
answer the line 2 call.
10. Key-guard
a. When the keyguard is selected, all keys will be locked.
Press UNLOCK (Left) soft key followed by ＊ to release it.
b. The keyguard will be automatically enabled once returning back to idle
mode for 15 seconds.
11. Dialing Prefix
a. Up to 14 digits, including pause(s), one access code can be preprogrammed to be added automatically in front of the dialed number
when dialing from call logs, phonebook, and dial-and-send dialing.
12. Call Hold
a. Places call on hold
13. Mute
a. Press MUTE (Left) soft key during talk, the handset microphone will be
muted.
Press UNMUTE (Left) soft key to release it.
14. Phonebook
a. 50 entries, each stores a phone number or handset ID (up to 26 digits) and
name (up to16 characters)
b. Alphabetically sorted display and search by letter.
~17~
c.
d.
Dial from display.
During the stand-by mode, you can enter the phone book by pressing
e.
scrolling key.
Phone book transfer via air
i. Transfer specific phonebook to one handset or all registered handsets
ii. Transfer all phonebooks to one handset or all registered handsets
15. Key tone
a. Four-level key tone volume selections (Off/Low/Medium/High).
b. Four key tone type selections.
16. Call Timers
a. Display call time duration for current call during and immediately after the
call.
17. Programmable Feature Call
a. Allow user to pre-program the most frequently used Feature code into SP935 which is adjunct to the PBX system.
b. Up to 10 entries can be saved.
c. Once the feature code is being programmed, you can quickly perform
those functions during the call by pressing OPTION soft key.
18. Menu Display
a. To avoid mis-setup in the “Call Settings”(MENU-4), “Phone Settings”
(MENU-5), “Base Settings” (MENU-6) and, these settings can be hidden.
b. Handset password is required before enter Menu Display (MENU-8), the
default handset password is “0000”.
c. When disabling the settings, these setting will not displayed any longer,
unless enabled by entering Menu Display again.
19. PA On/Off
a. Enable or disable the broadcast function.
b. When PA is Off, the handset can’t receive broadcast from base station or
other registered handsets; But it can broadcast to base station or other
registered handsets.
20. Group Setting
a. Allow handset to subscribe to one or several groups.
Re: Up to 7 groups (1~7) can be subscribed.
21. Custom Name
~18~
a.
Allow changing the “SP-935” screen to the desired wording or info, such as
the user’s name.
Re: Up to 32 characters can be entered.
22. Change Pwd
a. Allow changing the handset password which requires entering in Call
Barring (MENU-4-3) and Menu Display (MENU-8) .
Re:Default is “0000”.
23. DTMF Duration
a. From MENU-6-1 to select variable duration of DTMF tone.
b. Default is 100ms.
c. When entering the Base Settings, PIN is required. Default is “0000”.
Re: Better to check with your phone company first before changing it.
24. Programmable Flash key timing
a. From MENU-6-2 to select flash key timing
b. 9-level (100 ms - 900 ms) timing selections, default= 600 ms.
c. The default value (600 ms) works in most areas. Changing this setting may
cause Flash key not working. Change only when you are certain of the new
value would work.
d. When entering the Base Settings, PIN is required. Default is “0000”.
25. Assign next handset ID for new handset
a. Using registered handset from MENU-6-3 to assign a next handset ID to a
new handset.
b. If not assign next handset ID, the system will automatically assign a
handset ID to a new handset..
c. When entering the Base Settings, PIN is required. Default is “0000”.
b.
c.
Default PIN is “0000”.
When entering the Base Settings, PIN is required. Default is “0000”.
28. Auto Hang Up feature
a. Using registered handset from MENU-6-6 to turn on/off the Auto hand up
feature.
b. If turning on the feature, the handset will automatically hang up the call
when the far-end hangs up the call.
c. When entering the Base Settings, PIN is required. Default is “0000”.
29. Set Time
The set time function allows user to set date/time to support the DTMF caller
ID (DTMF caller ID doesn’t attach date/time when receiving from PSTN, using
this setting, user is able to review the date/time when the caller ID received).
a. Enter MENU-6 to set Base Settings.
b. Press
or
scrolling key to select desired base station
c.
d.
e.
f.
Enter Base PIN (Default is “0000”).
Enter 7 to enter Set Time.
Enter 6 digits for YY/MM/DD(Year/Month/Day), then enter 4 digits for
hr:mm (Hour：Minute)
Press SAVE (Left) soft key to finish the setting.
30. Mic Gain
Allow changing the handset microphone gain based on the handset in
different environment – Quiet, Normal and Noisy environment.
This requires entering the “Phone Settings” (MENU-5-1).
31. Headset Ring
Allow changing the ringer emitted either from handset speaker or receiver of
headset.
This requires entering the “Phone Settings” (MENU-5-8).
26. Clear Handset
a. Using registered handset from MENU-6-4 to remove the other registered
handset, in case the other registered handset is defected.
b. Once clear the other registered handset, the user is able to register a new
handset for instead.
c. When entering the Base Settings, PIN is required. Default is “0000”.
27. Change PIN
Allow changing the base PIN which requires entering the “Base Settings”
(MENU-6-5).
a. Using registered handset to change PIN from MENU-6-5.
~19~
~20~
Base Illustration
Base Features
CONSOLE
AUDIO IN
LINE
REGISTER
LAN
DC In
Basic Base Station Features
RESET
GROUND
Volume
Intercom
Broadcast
1.
Audio in Jack (3.5mm)
Connect to an external device for music on hold
2.
FXO Jack (L1)
Standard RJ-11 connector to plug in the telephone line
3.
Ethernet Jack
Standard RJ-45 connector to plug in the Ethernet (LAN) line
4.
Console jack
Jack for console and firmware upgrade (Type-B USB connector)
5.
GND
Connecting the ground cable
6.
REG button for Registration and Page
a. Press and hold this REG button till the “INTERCOM” LED into flashing status
to enter registration mode.
b. To search a misplaced handset; press “REG” button, all registered handsets
beep for 30 seconds. Press “REG” again or any key on handset to stop.
7.
RESET Button
a. Restores base station to factory settings
b. Reset button is intended to prevent accidental system reset.
c. All handsets (including administrator) and additional base(s) need to be reregistered after a base station reset. The web configuration is also to reset
to factory setting.
8.
DC In: to plug in the 12V DC power adaptor
Antenna
Receiver
Microphone
~21~
~22~
Charger Features
Charger Illustration
1.
DC In
Connects to Charger AC Adaptor.
2.
Handset Charging Slot
a. Charge handset battery when handset is placed in cradle.
b. Refer to the handset LCD for charging status
DC In
(1) Charging: battery status bar is running and the LCD screen showed:
“Charging”.
(2) Fully Charged: battery status bar stands still and the LCD screen would display
“Charge Complete”
(3) Charge Fail: Should there be any error occurred during charging mode, the
LCD screen would display “Charge Fail”
Spare Battery Charging
Slot
Spare Battery Charging
Indicator
Handset Charging Slot
3.
It is impossible to overcharge the battery using this charger.
4.
The adaptor for charging station can be used as travel charger as well.
However, you can’t turn off the power while you charge the handset via travel
charger. A warning message” “Unplug Travel Charger then OFF” will be shown
on the LCD.
Notes:
1. Fully charge battery packs before first use.
2. Handset will be “power on” automatically when placing on the
charging slot.
3. However, if you run drain the battery, it will take around one minute
for handset to auto power on.
~23~
~24~
Getting Started
Handset and Charger Installation
Base Station Installation
1.
Plug the transformer end of the Charger AC/DC adaptor into a standard AC
electric power outlet, plug the other end into the “DC In” jack on the back of
the Charger.
2.
Install battery pack onto the handset.
3.
Install handset antenna.
4.
Place handset onto the charger slot.
5.
Fully charge the battery for three hours before use.
6.
The phone system is now ready to perform basic functions such as making and
receiving phone calls and intercom calls. No base station or handset
programming is needed for basic operations.
1.
Plug the transformer end of the base
station AC/DC adaptor into a standard AC
electrical power outlet, plug the other end
into the “DC In” jack on the back of the
base station.
2.
Plug phone cord into the “RJ11” FXO jack
3.
Plug Ethernet cord into the “RJ45” LAN jack
PS: SIP configuration please see P50.
Note:
1. Handset(s) packaged along with a Base Station are pre-registered at
the factory. If you have a new handset, you will need to register the
handset with the base station in order to be recognized as a member
handset by the base(s) and by other handsets. See Handset
Registration.
2. Fully charge battery packs before the first usage.
~25~
~26~
Basic Operations
3. Menu Tree
Operation Modes
Menu
Both the base station and handset have levels of operation at which time only
certain procedures of functions can be performed.
1.KeyGuard
2.PhoneBook
3.Sounds
2.Ring Tone
A. Base Operation Modes
1. STANDBY mode- this is the default mode. The page key is active in standby
mode only. The base “Power” (blue color) LED will light up during this mode.
2.
3.
TALK mode- the base station operates in this mode during phone call. The “In
Use” (white color) LED will light up during this mode.
4.Key Tone
4.Call Settings
d.
d.
2.Group Setting
2.Line On/Off
3.Call Manager
Incoming
3.Int. On/Off
4.Feature Call
Outgoing
1.Auto
3.Off
5.Phone Settings
1. Mic. Gain
2.Any Key Talk
3.Contrast
4.Backlight
5.Name Tag
6.Custom Name
7.Change Pwd
8.Headset Ring
1.DTMF Duration
2.Flash time:
Main Menu
1.KeyGuard
6.Base Settings
Enter
Base PIN:----
3.Assign Next HS
4.Clear HS
5.Change PIN
SELECT
BACK
6.Auto Hang Up
7.Registration
The Menu structure display as below:
8.Menu Display
~27~
1.PA On/Off
Call Barring
down the
key for 3 seconds.
The standby screen display (custom name) can be
edited.
The 2-dight number represents the handset ID
MENU mode
a. Press the Right soft function key to activate Menu
mode.
b. In Menu mode, the handset settings and information
contained in memory can be changed.
c. The functions available through the Menu selection
are covered in greater detail from page 43.
1.Dial Prefix
2.Manual
B. Handset Operation Modes
1. STANDBY mode- this is the default mode.
a. If there is no on-going activity, the handset
automatically goes into SLEEP/STANDBY mode to save
battery power.
b. The handset can be turned off completely by holding
2.
3.Key Voulme
REGISTRATION mode- the base station enters this mode by pressing and
holding the REG button for 5 seconds. The 4 LEDs will be blinking in
“Registration” mode, also a prompt sound will be emitted.
c.
1.Ring Volume
1.Register
7.Set Time
2.Deregister
8.Line Detection
3.Remote REG
1.Call Setting
Enter Password
----
2.Phone Setting
~28~
3.Base Setting
The SP-935 Cordless Phone System offers private, Intercom/ 2-way radio calls
independence of base station. Intercom/ 2-way communication can be placed
between handsets.
Making a Telephone Call
1.
Press
number.
, wait for dial tone, and then enter phone
2. Alternatively, you can enter phone number first then press
11
Press REDIAL
or dial number
REDIAL
key.
When using this method, you can use the CLEAR (Left) and
DELETE (Right) soft keys to edit the number entered.
“Delete” erases the last digit entered. “Clear” erases the
entire line but remains in the dial-and send dialing.
1. Press
Group ID.
MENU
2.
Press
key to end the call.
Notes:
1.
2.
3. Speed dial by access the entries in the phone book
(Menu 2)
a. Press
or
scrolling key to enter the phone
book
b.
4.
key followed by a two-digit handset ID or
3.
Intercom calls can be made regardless if the Base Station is
present.
If a Group ID is entered, the first handset (belonging to that
group) that answers will establish a link with the caller. See
Handset Group Subscription.
If a link cannot be established, the LCD shows “Paging timeout”
after a 35-second time out.
Making a Broadcast
Press
to dial out the number
To abort dialing, press
Handset to Handset Calls
1. Broadcasting all handsets
a. Press and hold
key.
b. Start to speak the message to be broadcasted once you hear the key tone;
the speakerphone of destination handsets will be opened up, if it received
the voice.
Notes:
1.
Re: the initiating handset press and hold the
the speaking or broadcasting.
If a link cannot be established, the LCD will show “Base not found”
after a 6-second time out.
2.
key from one handset.
A call duration timer will start displaying the length of the call after
c. Release
key is needed during
key to end the broadcasting.
link is established.
2. Broadcasting a group of handsets
a. Enter the Group ID and then press and hold
Making an 2-Way/ Intercom Call
key.
~29~
Start to speak the message to be broadcasted once you hear the key tone;
the speakerphone of destination handsets will be opened up, if it received
~30~
the voice.
ringer has been turned off.
Re: the initiating handset press and hold the
during the speaking or broadcasting.
c. Release
key is needed
2. If the handset is on the charger cradle (ringer will be
temporarily switched to “Ring” if it has been set to
key to end the broadcasting.
“Vibrate”), lift the handset and press
conversation.
3. Broadcasting an individual handset
a. Enter the Handset ID and then press and hold
key to start
Re: You can turn on the “Any Key Talk” from MENU-5-2
key.
b. Start to speak the message to be broadcasted once you hear the key tone;
the speakerphone of destination handsets will be opened up, if it received
the voice.
Re: the initiating handset press and hold the
during the speaking or broadcasting
c. Release
key to end the broadcasting.
key is needed
Notes:
1.
2.
You can press SILENT (Left) soft key if you choose to ignore the call.
Unlike turning off the ringer (from the handset menu), the SILENT
key operation is valid only for the current call.
If Caller ID service is available, the LCD will display the incoming call
information. If the LCD shows “Private” or “Unknown”, the caller’s
information may have been blocked by the caller or the originating
phone company.
Redial
Receiving an Intercom Call
1. Press REDIAL (Left) soft key.
2. The LCD shows the last phone number dialed. To dial this
number, press
key.
Use
key to scroll through the last 10 phone
ringer has been turned off. Press
intercom call.
3.
or
1. When an intercom call arrives (called from other handsets,
ex. Handset 12), the ringer will ring or vibrate unless the
numbers dialed. Select and press
key to dial the
selected number.
[Note] Intercom numbers (Handset ID) are not stored in the
last 10 numbers dialed log.
Receiving a Telephone Call
1. When an incoming call arrives, the LCD will show the caller
ID message, and the ringer will ring or vibrate unless the
~31~
to answer the
2. If the handset is on the charger cradle (ringer will be
temporarily switched to “Ring” if it has been set to
“Vibrate”), lift the handset and press
conversation.
key to start
3. If the handset is not on the cradle and MENU-6-2 “Any Key Talk” setting is “On”,
press any key (except
and the SILENT soft key) to answer.
Notes:
1. The LCD displays the caller’s Handset ID.
2. You can press the SILENT (Left) soft key if you choose to ignore the call.
~32~
Unlike turning off the ringer the SILENT key operation is valid only for
the current call.
2. To return to the conversation, press UNHOLD (Left) soft key
Notes:
1. Handset LCD displays a call is being on hold. An alert tone (double
beep) every 30 seconds will remind the handset that a call is being on
hold.
2. If the operation (e.g., call transfer) after putting a call on-hold fails,
the held call may be dropped.
Ending a Call
To end a telephone or intercom call, press
cradle.
key, or place handset into charger
Mute
Adjusting Handset Receiver (Earpiece) Voice Volume
2. When mute is active, the other end will not hear your
voice, but still can speak to you.
1. Voice volume can only be adjusted during a call.
2. There are 6 levels of volume selections. Use
1. After a link is established, you can press MUTE (Left) soft
key to mute the handset microphone.
or
3. To leave the mute state, press UNMUTE (Left) soft key. Mute is effective only
for the current call.
key to adjust
3. The new setting remains effective for all future calls until
changed.
Adjusting Handset Speakerphone Voice Volume
1. Voice volume can only be adjusted during a call (in
speakerphone mode).
2. There are 6 levels of volume selections. Use
or
Do Not Disturb (Silent Ring)
1. Enter the key sequence MENU-3-1, then select “Off”. Press
SELECT (Left) soft key to confirm your choice. This will turn
off the ringer until it is turn on again from the menu.
2. For temporary silencing the ringer when an incoming call
arrives, press SILENT (Left) soft key.
key to adjust
Key Guard
3. The new setting remains effective for all future calls until
changed.
1. To prevent accidental dialing, you can press MENU (Right)
soft key, then press“1” to select Keyguard option. The
handset keypad is locked. No key entry is accepted.
Placing a Call On Hold
1. When a call is in progress, it can be put on hold by pressing
OPTION (Right) soft key and the ＊ key
~33~
2. To unlock the keypad, press UNLOCK (Left) soft key, then,
~34~
within 2 seconds, press the digit ＊ to unlock.
Advanced Operations
Handset Registration
3. Once returning back to standby mode for 15 seconds, the
keyguard will be automatically enabled.
1.
If your handset(s) is purchased as part of a system, it has been pre-registered
with the base station at the factory.
4. Key Guard is in effect until unlocked.
2.
If Handset ID as “00,” that means it is a new handset or the ID has been
erased. You need to register the handset with the base station.
Battery Recharge and Replacement
3. Registration:
a. Press MENU-7 to enter the registration mode
b. Press and hold the base’s PAGE button for 3 seconds
until the In Use LED (white color) lighting up and
flashing, also the base station will emit prompt sound
to remind you the base station is in the registration
mode..
c. Press handset key 1 , this completes the registration
process. The base station will assign a handset ID
between 11 and 19 automatically. The assigned ID will
be displayed on the handset LCD, indicating successful
registration.
1.
Charge the battery when one or several of the following happen:
a. Phone beeps twice (every 60 seconds in talk mode, every 10 minutes in
standby mode).
b. Battery icon is empty.
c.
Phone does not respond when a power on/off key
is pressed.
d. LCD and backlighting become dim.
e. Talk range shortfall is experienced.
2.
You can replace the handset battery after placing the call-in-progress on hold
and press
key. To retrieve the call on held, press talk key again after
replaced battery and power the handset on..
3.
Battery talk time and standby time vary depending on the talk/standby pattern
and the operating distance. Putting the handset back to charger cradle as
often as possible is recommended for best performance. Use only
manufacturer provided battery and charger!
d. Repeat above steps for all additional handsets.
4. De-registration:
a. You can de-register the handset you’re using from the
base station. De-registration will reset the Handset ID
to 00, erase the system security code, and free up the
handset ID for future registration.
b. After deregistration, the handset will not be able to use
the base station to make or receive phone calls, nor can
it intercom other handsets.
c. Press MENU-7 to enter the registration mode
d. Press and hold the base’s PAGE button for 3 seconds
until the In Use LED (white color) lighting up and
flashing, also the base station will emit prompt sound to
remind you the base station is in the de-registration
mode.
e. Press the handset number key 2 , this completes the
~35~
~36~
de-registration process. Upon successful deregistration, the handset display will show ”Please
register”.
Notes:
1. The base station has a 30 second registration timeout starting from
pressing the PAGE button. The handset has a 6 second registration
timeout starting from the registration or de-registration option has
been selected. The base station and handset will automatically exit
registration mode after timeout.
2. Repeat registration or de-registration process if unsuccessful.
Notes:
1. The handset can change group affiliations at any time.
2. The base station is not responsible for group assignments.
Consequently, it cannot de-subscribe a handset from a group.
3. When an intercom caller enters a group ID, all handsets subscribed to
this group will ring. The first handset to answer will establish a link
with the caller. Afterward, it is a one-to-one call, not a one-to-many
call.
Call Transfer
Handset Group Subscription
While a telephone call is in progress, you can transfer it between different
handsets.
1. Up to nine handset groups (1-7) can be defined and
handsets can decide which group(s) they want to be in.
2. For example, Group 1 represents the Customer Service
Group, Group 2 represents the Sales Group,
Direct transfer
1. Press OPTION (Right) soft key, followed by the ＊ key to put
the call on hold.
and Group 3 is the Marketing Group. Suppose that Handset Call Settings
11 wants to receive incoming rings for all Sales and
2.Group Setting
Marketing related calls. Then handset 11 will need to
SELECT
“subscribe” to Group 2 and Group 3.
BACK
2. Press OPTION (Right) soft key, followed by the 1 key or
SELECT soft key of XFER, pressed destination handset ID,
then the held call will be transferred directly.
After the call transferred to destination handset, the original
handset will go back to standby mode automatically.
3. Group Selections:
a. Press handset MENU-4 to enter the Call Settings menu
b. Press number 2 , handset enters group setting menu.
c. Press OPTION soft key and followed by 1 key to
subscribe the group (“＃”, ＃:1~7). Enter 1~7.
d. Repeat for all desired groups.
e. Delete group selections by pressing OPTION soft key
and followed by 2 to Unsubscribe the group.
Indirect transfer
If you want to talk to the destination handset before the call
transferred, you can follow with below method:
1. During the call, press
key, followed by entering the
destination handset ID.
2.
Press the
of the destination handset to answer the
intercom call, you can now talk to the destination handset.
After the talking, press
to end the intercom call, then
the destination handset is able to pick up the incoming call
~37~
~38~
automatically.
records without name will be placed on top of the
phonebook list.
f. To enter the name, press the corresponding keypad
number one or more times according to the order of
the character on the key.
See table below for a list of available characters and
their orders. For example, press 2 once for the
character “A”, twice for “B”, etc.
After the call transferred to destination handset, the original
handset will go back to standby mode automatically.
Notes: If the destination handset does not answer after handset paging or
transferring timeout, the call is routed back to the originating handset.
Notes:
1. When enter a phone number, the cursor automatically advances to the
Phonebook Operations
2.
1. You can store up to 50 entries in the phonebook. Each
entry can contain a phone number or handset ID (up to 26
digits) and a name (up to16 characters).
next digit field. Use
or
scrolling key to move the cursor
backward or forward to insert or delete (the digit above the cursor, or left
of the cursor if cursor is on the right of the last digit).
When entering a name, the cursor automatically advances to the next
character field if you press a different key for the next character. If you
need to enter consecutive characters from the same key, you can wait for
the cursor to advance or use
2. To access the phonebook, press MENU (Right) soft key,
followed by 2 ; or press
scrolling key while the
handset is in standby mode.
Main Menu
2.PhoneBook
SELECT
BACK
3.
4.
3. To add a new entry:
a. Press ADD (Left) soft key.
b. Enter the name when LCD prompts “Name?” Use
DELETE (Right) soft key to delete the last digit entered.
When completed, press SAVE (Left) soft key to save.
Re: Up to 16 characters can be entered as the name.
or
cursor backward or forward manually. Also use
or
to move
the cursor to insert (to the left of the cursor) or delete (the character
above the cursor, or left of the cursor if cursor is on the right of the last
character).
By default, all letters are entered in the upper case. Use the ＊ key to
toggle between upper and lower cases.
A “Pause” entry represents a 1 second delay in dialing the following digits,
which is useful when calling a sequence of segmented numbers (e.g.,
access code, credit card number, auto-attendant entries, etc.) Pause is
entered by pressing the ＃ key twice (LCD displays P). Entering pause
twice (PP) will result in 2 seconds pause in the dialing.
c. You will then be prompted to enter a number for the
name just entered.
Re: Up to 26 digits can be entered as the number.
d. After entering the number, press the SAVE (Left) soft
key to save this entry into phonebook.
e. Enter a phonebook entry without a name, the all
~39~
scrolling key to move the
~40~
b. Press OPTION (Right) soft key to enter option menu.
5. Character Table:
Key
＊
Characters and Orders
‘+,.*()&1
ABC2
DEF3
GHI4
JKL5
M NO 6
PQRS7
TUV8
WXYZ9
Caps – when in character editing.
＊– when in number editing.
Space & ＃ – when in character editing
# & P (Pause) – when in number editing
4.
The entries are alphabetically sorted and stored as a list in an ascending order
(A to Z) from the top of the list.
5.
The first line of LCD display shows name and the 2 line shows the phone
number. If the phone number is longer than 16 digits, press OPTION (Right)
soft key and select Option 3 “View Number” to view the complete number.
6.
c. Press 1 to erase the desinated phone entry.
d. LCD shown “Delete entry?” Press YES (Left) soft key to
confirm your change.
8. To edit phonebook:
a. Use
or
scrolling key or the alphabetical
search method to locate the record to be erased or
edited.
b. Press OPTION (Right) soft key to enter option menu.
c. Press 2 to edit the desinated phone entry.
9.
Dial from display:
a.
or
Press
to dial the phone number or Handset ID displayed.
nd
To search for a record:
a. Use
scrolling key to enter the Phone Book mode.
b.
c.
d.
Press a key that corresponds to the first character of the name you are
looking for.
For example, you are looking for “EnGenius”, and then press the number
3 twice.
Use
or
looking for.
scrolling key to locate the exact record you are
7. To erase phonebook:
a. Use
or
scrolling key or the alphabetical
search method to locate the record to be erased or
edited.
~41~
10. To transfer phonebook:
To transfer phonebook, both parties have to enter the phonebook transfer
mode firstly by following below:
a. Press OPTION (Right) soft key follow by 5 or or
scrolling key to
transfer when handset in phonebook mode.
b. For phone sending party, press 1 to enter sending mode.
i. Either press TX ALL(Left) soft key to transfer all phonebook entries to
another handset(s).
ii. Or press TX ONE (Right) soft key to transfer one entry to another
handset(s).
iii. Press 2-digit handset ID or group ID, then select all phonebook entries
or one entry to be transferred.
Re : “00” means all handsets
iv. During phonebook transferring, LCD shows “Sending” and 2-digit
countdown on the LCD to indicate the phonebook numbers which are
waiting for sending.
c. For phonebook receiving party, press 2 to enter receiving mode.
i. When entering the receiving mode, LCD shows “Ready”.
~42~
ii. Start to receive phonebook, LCD shows “Get phonebook from Ext. # :
xx”.
iii. A beep emitted when receiving each phonebook.
iv. When the phonebook receiving, 2-digit countdown on the LCD to
indicate the phonebook numbers which are waiting for receiving.
Re: The phonebook transfer through the wireless interface, it may partially miss
transmission by interference.
g. Press OPTION (Right) soft key to delete or edit the
feature call you programmed into the system.
h. Repeat the same operations to program 2nd and even
more feature call that you will use frequently.
4. Using pre-programmed feature call during the call.
Programmable Feature Call
1. If SP-935 base station is installed behind a PBX system, it is feasible to preprogram some feature call along with the PBX’s feature code into the system.
a. Press OPTION (Right) soft key while the handset is in the
talk mode.
b. Press the correspondence number of the feature call
which you want to perform i.e. press “0” to perform
the “PBX Transfer”.
2. Up to 10 most frequently used feature call codes can be pre-programmed.
3. Name and enter feature call codes:
a. Press MENU (Right) soft key while the handset is in the
standby mode.
b. Press 4 , followed by 4 to enter the “Feature Call”
menu.
c. Press ADD (Left) soft key to add a new entry of feature
call.
d. Key in the name of feature call, like editing a
phonebook entry, i.e. “PBX Transfer”.
Press SAVE (Left) soft key to confirm.
e. Key in the feature call code of the correspondence PBX
feature i.e. F＊70.
Press SAVE (Left) soft key to confirm.
Re: “F” represent the Flash signal.
f. The 1st feature call and correspondence feature call
code you entered will appear on the LCD screen.
Notes:
1. This feature call would be useful if the SP-935 base station is adjunct to a
PBX system,
2. if you have not pre-programmed any feature call into the system, only
“#.Phonebook” in the OPTION menu.
3. The SP-935’s programmable feature call may not function with all PBX or
Key phone systems due to the diversity of various proprietary systems.
Caller ID
1. Contact with your local phone company to subscribe to this feature. The phone
system receives and displays Caller ID information transmitted by your local
phone company. This information may include the calling phone number, name,
date and time. This unit can store up to 50 calls of caller ID information.
2. The display will show the date and time of call on the first line, followed by the
name on the second line, and the phone number on the third line. An unread
~43~
~44~
record will have a “NEW” at the end of the first line of display.
3. When viewing a call record, the number can be dialed, stored to the phonebook or
deleted.
View Call Log
1. To view the call log, press
Press
or
key to scroll through the numbers and
names when available.
or
When display a caller ID, Press
to dial this number.
Call Manager
“Call Manager” feature allows four options：
1. The first option is “Incoming”. The handset can be selected to enable receiving
the incoming PA, intercom call, line call or line dedicated.
to enter the Call Log.
2. Press OPTION right soft key, you can
choose save, delete, clear all.
a. Save call log:
2.
2. The second option is “Outgoing”. The handset can be set to access available
bases automatically or manually or pre-defined telephone line.
key to
3. The third option is “Call Barring”. The handset can be selected to block the calls
which are not allowed.
(1) Press SELECT right soft key, you can use
or
Note: When enter this menu (Call Manager), you must enter handset’s password
first (4 digits). The default password of handset is “0000”.
key to scrool the name, and press DELETE to
edit the name.
Then press SAVE left soft key to save the name.
Incoming
(2) Use
or
key to scrool the number, and
press DELETE to edit the number.
Then press SAVE left soft key to save the number.
1.
(3) After above process, the call log saved into
phonebook.
b. Delete call log:
(1) Press SELECT right soft key followed by YES left soft
key to confirm deleting.
Press 1 or 2 if muti-base is on to select Incoming.
a. Press 1 to enable receiving PA On/Off.
Re：Default setting is “ON”.
c. Clear All:
(1) Press SELECT right soft key followed by YES left soft
key to confirm clearing all caller ID records.
Call a Caller ID
1. Press
key on idle screen to enter the call log, use
Press MENU (Right) soft key followed by 4 to enter
the Call Settings mode.
Press 3 to select Call Manager followed by entering
handset’s password (4 digits).
b. Press 2 to enable receiving Line On/Off wich include
SIP and FXO line both.
Re：Default setting is “ON”.
c. Press 3 to enable receiving Intercom On/Off.
Re：Default setting is “ON”.
or
key to scrool the call log.
(1) By default all incoming calls will ring all handsets.
~45~
~46~
Re：Default of Call Barring “OFF”.
When enter this menu, you must enter handset password first (4 digits).
Re: The default password of handset is “0000”.
Outgoing
1.
Press MENU (Right) soft key followed by 4 to enter the
Call Settings mode.
Press 3 to select Call Manager followed by entering
handset’s password (4 digits).
Press 2 or 3 if muti-base is on to select “Outgoing”.
The hanset is able to make outgoing calls via the desired
line of base station
Re：Default setting is “Auto”.
a. Press 1 to “Auto”.The hanset is able to make outgoing
call via an available line and SIP ed bases automatically.
2.
To add the Call Barring code
a. Once turn on the Call Barring feature, you can key in the
“Call Barring” code
To add one block code, press ADD (Left) soft key then
start entering the Call Barring code. After the number
entering the Call Barring code., press SAVE (Left) soft
key to save.
(1) Up to 5 digits can be edited to be Call Barring code.
For example, if you want to block all call dialing to
Manhanttan, NY area, you can enter 1212 as the
Call Barring code.
(2) If you base station is adjuct to a PBX system, please
also include that specific number to retrieve the
PSTN tone.
b. Press 2 to “Manual”. When pressing
key in
standby mode, the handset LCD will show the available
or
to scroll the options: 1. SIP, 2
line. Press
Line. Press digit 1, you can select the SIP line 1 to make
a call..
c Press 3 to “Off”.The hanset is disable to make any
outgoing call.
c. If wants to block all outgoing calls, enter “＊ ＊ ＊ ＊
＊” 5 “＊” keys followed by, press SAVE (Left) soft key
to save it, all outgoing calls will be restricted.
Call Barring
1.
b. Press OPTION (Right) soft key to delete or edit the Call
Barring codes.
. Up to 5 sets of Call Barring codes can be programmed.
Press MENU (Right) soft key followed by 4 to enter the
Call Settings mode.
Press 3 to select Call Manager followed by entering
handset’s password (4 digits).
Press 3 or 4 if muti-base is on to select “Call Barring”
to block users from dialing the long distance calls or
international calls. And also block the incoming call from
outside line or other registered handset.
~47~
Visual Message Waiting Indicator (VMWI)
VMWI feature supported the FSK message which received from telephone line; It
will activate a message icon of handset and flash the VOICE MESSAGE LED of base.
Notes:
1. A subscription to telephone company voice mail service is required.
~48~
2. If the handset still indicates the icon even after you have listened all messages, turn it off
by pressing and holding “Caller ID” key on the handset.
SIP Configuration
Introduction
Adjust Handset Microphone Gain
In case you will use the handset in different workplace or environment, to perform
better voice quality for the other end, you can adjust the handset microphone gain
to suit for variable place.
a. Press MENU right soft key while the handset is in the standby mode.
b. Press 5 (Phone Settings), followed by 1 to enter the “Mic. Gain” menu.
c. Use
or
key to scroll the “Standard”, “Medium” and “Low”
options.
d. If you are using the handset in quiet environment, like office or meeting
room, the level of “Standard” is recommended.
The SP-935 is a long range cordless telephone system which built-in a SIP client
along with a traditional FXO port. It provides user the capability to make VoIP call or
PSTN call via different ports. Below describes how to setup the SIP configuration of
SP-935 base from web.
Application
Typically, the SP-935 is able to connect with a legacy PBX (or PSTN line) via a
telephone jack, and in addition with an IPPBX via a networking jack. These two
interfaces are perfectly suitable for adjunct telephone system for enterprise
environment as following figure.
If you are using the handset in a noisy environment, like factory or
outdoor place, the level of “Medium” or “Low” is recommended.
Adjust Headset Ring
When using headset, to avoid missing the call due to the ringer emitted from
receiver of headset, you can change the ringer emitting from either handset
speaker or receiver of headset.
a. Press MENU right soft key while the handset is in the standby mode.
b. Press 5 (Phone Settings), followed by “9” to enter the “Headset Ring”
menu.
c. Select On , the ringer will be emitted from the receiver of headset; If
select Off , the ringer will be emitted from handset speaker.
VoIP Features
- Support 3 VoIP and 1 PSTN line calls simultaneously.
- Each handset has only one SIP account.
- Up to register 10 SIP accounts and 10 handsets accordingly.
- Flexible call manager feature to dedicate the SIP or PSTN call.
- Use G.711U-law for VoIP codec
- SIP and LAN setting from web configuration
- Internet interface: 10/100base-T LAN port x1
Registration handsets
- Before setting the SIP configuration, the available handset(s) of SP-935 must
register to the base of SP-935.
- Register handset:
(1) Press and hold the register key on base till the “Intercom” key into flashing
status. During this flashing LED period, the base can perform the registration.
~49~
~50~
(2) In handset, enter “MENU, 7,1” to enter the registration.
(3) The assigned ID ( from 10 to 19) will be displayed on handset LCD, indicating
successful registration
(4) Repeat the above steps for all additional handsets.
Default settings
Connect the internet port to SP-935 LAN port.
IP Address
Username / Password
192.168.1.156
admin / admin
Web configuration
Open a web browser (Internet Explorer/Firefox/Safari/Chrome) and enter the IP
Address http://192.168.1.156
LAN configuration
The default username and password are admin. Once you have entered the correct
username and password, click the Login button to open the web-base configuration
page.
If successful, you will be logging in and see the configuration of SP-935.
Note: When you change the LAN IP to DHCP, once you click the “Apply” to take
effect the change. Then you should know the new IP of SP-935 in advance to access
the web configuration next time.
~51~
~52~
Base Settings
Note: When you change one of the Base Setting, you should click the “Apply” to
take effect the change. The items with gray color are not changeable and reserved
for other version..
Individual account
- Note: You should register every handset on SP-935 base, before you start setting
the SIP configuration,
SIP Configuration
The default SIP number is according to handset ID which means SIP number 10 for
handset ID 10 accordingly. You need to enter the Edit button for each account.
SIP server
SIP account
Enter VoIP-> Account Setting
~53~
~54~
Click the Apply button to save the setting as the screen showing:
After you finish these accounts setting, you need to click the Apply button as
following in red to activate the setting.
Tools
Admin
This page allows you to change the username and password. By default, the
username is admin and the password is: admin. The password can contain 0 to 12
alphanumeric this characters and is case sensitive.
Audio Setting
In this Audio Setting, after you change the setting and click “Apply”, you need to
power cycle the base in order for any changes take effect.
Admin
Login Name
Old Password
New
Password
~55~
Enter a new username for logging in to the New Name entry box.
Enter the old password for logging in to the Old Password entry
box.
Enter the new password for logging in to the New Password entry
box.
~56~
Repeat New
Password
Apply / Cancel
Re-enter the new password in the Confirm Password entry box for
confirmation.
Click Apply to apply the changes or Cancel to return previous
settings.
Time
This page allows you to set the internal clock.
Start
Click Start Ping to begin pinging target device (via IP).
Firmware
This page allows you to upgrade the firmware of SP-935.
To perform the Firmware Upgrade:
Click the Browse button and navigate the OS File System to the location of the
upgrade file.
Select the upgrade file. The name of the file will appear in the Upgrade File field.
Click the Apply button to commence the firmware upgrade.
Note: The device is unavailable during the upgrade process and must restart when
the upgrade is completed. Any connections to or through the device will be lost.
Back-up
Time
Time Setup
Time Zone
Apply / Cancel
Select to sync with a NTP server or with the PC internal clock.
Select a time zone from the drop-down list and check whether you
want to enter the IP address of an NTP server or use the default
NTP server to get have the internal clock set automatically.
Click Apply to apply the changes or Cancel to return previous
settings.
Diagnosis
This page allows you to analyze the connection quality of SP-935 and trace the
routing table to a target in the network.
This page allows you to save the current device configurations. When you save the
configurations, you also can reload the saved configurations into the device through
the “Restore Settings” from A File section. If extreme problems occur, or if you
have set the SP-935 wrongly, you can use the “ Reset” button in the Restore to
factory default section to restore all the configurations of the SP-935 to the original
default settings.
Back-up
Restore to factory
default
Backup Setting
Restore Setting
Click Reset button to restore the SP-935 to its factory default
settings.
Click Save to save the current configured settings.
To restore settings that have been previously backed up, click
Browse, select the file, and click Upload.
Reset/ReBoot/Registration
You can press and hold the below buttons to execute specific features, or using the
web setting instead.
Diagnosis
Address to Ping
Ping Result
Enter the IP address you would like to search.
Check the specific IP address alive
~57~
~58~
Menu Operations
Reset button
Reg button
These features (Reset, Reboot, and Registration) can be performed from this web
setting
~59~
~60~
1.
Press MENU right soft key to enter menu mode while the phone is in standby
mode.
Re: You can either press
or
, followed by SELECT left soft key to
confirm the selected menu. Or Press the digit directly to confirm the
selected menu. For example, press MENU right soft key followed by 4 and
1 to select the Ring Volume.
2.
Press 1 to select Keyguard (see Key Guard operation on page 34 ).
3.
Press 2 to add, delete, edit, view and edit the phonebook (see Phonebook
instruction on page 40 ).
4.
Press 3 to set Sounds settings:
a. Press 1 to select Ring Volume:
Two options for ring volume: Line (for incoming call) and Intercom (for
intercom call). Set each option respectively.
b.
When setting each option, use
or
to scroll through 6 options:
“Off”, “Low”, “Medium”, “High”, “Vibrate” and “Vibrate & High”. Press
SELECT left soft key to save selection. Default = Medium.
Press 2 to select Ring Tone:
Two options for ring tone: Line (ring tone for incoming call) and Intercom
(ringer for intercom call). Set each option respectively.
c.
Use the
or
to scroll through 8 ringers, press SELECT left soft
key to save selection. Default = 1.
Press 3 to select Key Volume when a key is pressed:
d.
Use
or
to scroll through 4 options: Off, Low, Medium, and
High. Press SELECT left soft key to save selection. Default = Medium.
Press 4 to select Key Tone:
= Off.
If “On” is selected, the handset is prompted to enter the prefix
number, up to 14 digits can be entered.
(3)
Use Delete right soft key to edit prefix number.
Press SAVE left soft key to confirm the selection.
(4)
(5)
When this feature is turned on, the LCD will prompt the user “Dial
Prefix? Yes or No” on each outgoing phone call from call logs,
phonebook, and dial-and-send dialing, the current prefix is also
displayed.
Re: the prefix number will be added automatically in front of the
dialed number if press YES left soft key.
(6)
This feature is useful for access code, calling card, and credit card
calls, etc.
Press 2 to Group Select: see Handset Group Subscription on page 37 .
Press 3 to set Call Manager: see Call Manager operation on Page 48.
Press 4 to set Feature Call: see Feature Call operation on Page 44.
(2)
b.
c.
d.
6.
Press 5 to set Phone Settings:
a. Press 1 to set Mic Gain: See Mic Gain operation on Page 52.
b. Press 2 to set Any Key TALK:
Use CHANGE left soft key to select and confirm “On” or “Off".
Default is “Off”.
Re: When set “on”, press any key (except
and SILENT key) to answer
the incoming call.
c.
Press 3 to set LCD Contrast:
(1)
Use
or
to scroll through option 1~8. Default is 4.
(2) Press SAVE left soft key to confirm selection.
d.
Press 4 to set LCD Backlight:
(1)
Use the
or
to scroll through 4 options: 1, 2, 3 and 4. Press
SELECT left soft key to save selection. Default = 1.
Use
or
to scroll through option 1~3 (1.8 seconds 2.On
3.Off ). Default is “8 seconds”.
(2) Press SAVE left soft key to confirm selection.
5.
Press 4 to set Call Settings:
a. Press 1 to set Dial Prefix:
(1)
Press
or
e.
Press 5 to set Name Tag:
(1) Use CHANGE left soft key to select and confirm “On” or “Off". Default is
to turn on or off the dial prefix feature. Default
~61~
“Off”.
~62~
(1) Use
(2) Press SAVE left soft key to confirm selection.
Re: When Set “On”, the handset match the caller ID with the phone book
entries; once matched, the LCD screen will display the name or
nickname instead of pure caller ID info (needs Call Waiting with Caller
ID service from local telephone company)
c.
f.
d.
Press 6 to set Custom Name:
(1) Enter characters using the Character Table and method discussed in the
Phonebook section.
e.
(2) Use
or
to move the cursor backward or forward to insert
(to the left of the cursor) or delete (the character above the cursor, or
left of the cursor if cursor is on the right of the last character).
f.
(3) Press SAVE (Left) soft key to confirm setting.
Re: Once entering the custom name, the greeting of LCD in standby mode
will be changed as the entering.
Default greeting is “SP-935”.
g.
g.
Press 7 to Change Password:
(1) Enter original (4 digits) of handset then press OK left soft key when
f.
enter this menu.
(2) Enter new password (4 digits) then press SAVE left soft key to confirm
new password.
h.
7.
or
to scroll through option 1~9 (100~900ms). Or press
digit key (1~9) directly.
(2) Press SELECT left soft key to confirm selection.
Re: The default value (600 ms) works in most areas. Changing this setting
may cause Flash key not working. Change only when you are certain of
the new value would work.
Press 3 to set Assign Next HS
(1) Enter 2-digit handset ID followed by pressing OK left soft key.
(2) When register a new handset, the base will assign the specific handset
ID which assigned in advance to the new handset.
Press 4 to set Clear HS
(1) Enter 2-digit handset ID followed by pressing OK left soft key.
(2) The base will erase the handset ID from system.
Press 5 to Change PIN:
(1) Enter the new Base PIN followed by OK left soft key.
Re: Default Base PIN is “0000”.
Press 6 to set Auto Hang Up:
(1) Use CHANGE left soft key to select and confirm on or off.
Re: When setting “on”, the SP-935 will automatically hang up if the far end
caller hung up already. However, this function depends on if there is
“dial tone or busy tone” signal sent out by PBX or PSTN, after the call
hung up.
Press 7 to Set Time to support DTMF Caller ID:
(1) Use SAVE left soft key to select and confirm the Date and Time you
have set (see Set Time operation on page 20).
Press 8 to set Line Detection:
(1) Use CHANGE left soft key to select and confirm on or off.
Re: When setting “on”, the SP-935 will automatically see if the telephone
line is plugged in or not. Once the telephone line is not available, user
can’t select the line to make an outgoing call manually.
Press 8 to set Headset Ring: See Headset Ring operation on Page 52.
Press 6 to set Base Settings:
When enter this menu, you must enter Base PIN code first (4 digits).
Re: The PIN code is for Base Settings. Default is “0000”.
a. Press 1 to set DTMF Duration.
(1) Enter the DTMF duration (90~200ms), press OK left soft key to confirm
the setting. Default is 100ms.
Re: Please check with your dealer before you change it. If the duration not
matches with PSTN or PBX setting, it may operate faultily.
b. Press 2 select flash key timing. Default is 600ms.
~63~
8.
Press 7 to register, de-register handset : see Handset Registration operation on
Page 36,
9.
Press 8 to set Menu Display:
To avoid mis-setup of Call Settings (MENU-4), Phone Settings (MENU-5) and Base
Settings (MENU-6), you can hide these menus, so that other handset users won’t
have chance to mis-settup these settings.
Re: When entering the Menu Display, you have to enter password first.
~64~
a.
Press 1 to set hiding/un-hiding of the Call Settings menu.
(1) Use CHANGE left soft key to select and confirm on or off.
b.
Press 2 to set hiding/un-hiding of the Phone Settings menu.
(1) Use CHANGE left soft key to select and confirm on or off.
c.
Press 3 to set hiding/un-hiding of the Base Settings menu.
(1) Use CHANGE left soft key to select and confirm on or off.
Re: Select “On” means the menu will be displayed on screen. Select “Off” means
the menu will be hidden.
Technical Specifications
Electrical Specifications Base Station
Frequency 902-928 MHz
RF Power Peak: 708 mW
Average: 354 mW
Channel Spacing 200 kHz
Number of Channels 128
Modulation MSK
Multiple Access Frequency Hopping TDMA
Frequency Hopping Rate
TDMA Frame Length
Number of Slots/Frame
Number of Users/Carrier
Receiver Sensitivity
100 per second
10 ms
-2
< -108 dBm (@ BER 10 )
Antenna Connector Reverse TNC
Antenna Gain 2 dBi
5 dBi External (optional)
TX Power Control Range NA
Telephone Interface RJ11 x 1
VoIP interface RJ45 x 1
SIP protocol RFC 3261
Speech Coding 64Kbps G.711alaw, G.711
ulaw
Channel Coding 8 kbps Convolutional + CRC
Transmission Data Rate 170.667 kbps
User Data Rate 128 kbps duplex
Duplex Time Division Duplex (TDD)
Voice Quality
No. of System ID
Ring Signal
Auto-Attendant Coding
TIA/EIA-470B
65,536
20-50 Hz, 15-90 Vrms
64Kbps G.711alaw, G.711
ulaw
Flash Time 100-900 ms programmable
Power Source 100~240V/12V AC/DC
Adapter
Charger Current NA
~65~
~66~
Portable Handset
902-928 MHz
Peak: 708 mW
Average: 88.5 mW
200 kHz
128
MSK
Frequency Hopping
TDMA
100 per second
10 ms
< -108 dBm (@ BER 10
Non-standard
2 dBi (Long)
0.5 dBi (Short)
100-708 mW
NA
NA
NA
8 kbps G.729A
8 kbps Convolutional +
CRC
170.667 kbps
128 kbps duplex
Time Division Duplex
(TDD)
TIA/EIA-470B
65,536
NA
8 kbps G.729
NA
3.7V, 1700 mAh Li-ion
Battery
500 mA
Charge Time
Regulation Compliance
Operating Temperature
Storage Temperature
Humidity
Dimension without
antenna
Weight
NA
FCC Part 15, Part 68
0 – 50 °C
-10 – 70 °C
20 – 75 %
161W x 42D x 188H (mm)
6.3” x 16.5” x 7.4”
14.1 ounces
4 hours (from empty)
FCC Part 15, Part 68
-10 – 60 °C
-10 – 70 °C
20 – 75 %
161 x 58 x 31 mm
6.17 ounces
Base Station
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
15.214 (d) Cordless telephones shall incorporate circuitry which makes use of a
digital security code to provide protection against unintentional access to the public
switched telephone network by the base unit and unintentional ringing by the
handset. These functions shall operate such that each access of the telephone
network or ringing of the handset is preceded by the transmission of a code word.
~67~
~68~
Access to the telephone network shall occur only if the code transmitted by the
handset matches the code set in the base unit. Similarly, ringing of the handset shall
occur only if the code transmitted by the base unit matches the code set in the
handset. The security code required by this Section may also be employed to
perform other communications functions, such as providing telephone billing
information. This security code system is to operate in accordance with the
following provisions.
(1) There must be provision for at least 256 possible discrete digital codes. Factoryset codes must be continuously varied over at least 256 possible codes as each
telephone is manufactured. The codes may be varied either randomly, sequentially,
or using another systematic procedure.
(2) Manufacturers must use one of the following approaches for facilitating
variation in the geographic distribution of individual security codes:
(i) Provide a means for the user to readily select from among at least 256 possible
discrete digital codes. The cordless telephone shall be either in a non-operable
mode after manufacture until the user selects a security code or the manufacturer
must continuously vary the initial security code as each telephone is produced.
(ii) Provide a fixed code that is continuously varied among at least 256 discrete
digital codes as each telephone is manufactured.
(iii) Provide a means for the cordless telephone to automatically select a different
code from among at least 256 possible discrete digital codes each time it is
activated.
(iv) It is permissible to provide combinations of fixed, automatic, and userselectable coding provided the above criteria are met.
(3) A statement of the means and procedures used to achieve the required
protection shall be provided in any application for equipment authorization of a
cordless telephone.
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux
appareils radio exempts de licence. Son fonctionnement est sujet aux deux
conditions suivantes: (1) le dispositif ne doit pas produire de brouillage
préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un
brouillage susceptible de provoquer un fonctionnement indésirable.
IMPORTANT NOTE:
~69~
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain
of 2dBi. Antenna having a higher gain is strictly prohibited per regulations of
Industry Canada. The required antenna impedance is 50 ohms.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé
avec un minimum de 20cm de distance entre la source de rayonnement et votre
corps.
Ce dispositif a été conçu pour fonctionner avec une antenne ayant un gain maximal
de dB 2. Une antenne à gain plus élevé est strictement interdite par les règlements
d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.
Telecom
This equipment complies with Part 68 of the FCC rules and the requirements
adopted by the ACTA. On the EUT of this equipment is a label that contains, among
other information, a product identifier in the format US: SNIW401BSP935. If
requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected
to a telephone line. Excessive RENs on a telephone line may result in the devices
not ringing in response to an incoming call. In most but not all areas, the sum of
RENs should not exceed five (5.0). To be certain of the number of devices that may
be connected to a line, as determined by the total RENs, contact the local telephone
company. For products approved after July 23, 2001, the REN for this product is part
of the product identifier that has the format US: SNIW401BSP935. The digits
represented by 01 are the REN without a decimal point (e.g., 03 is a REN of 0.3). For
earlier products, the REN is separately shown on the label.
If your equipment causes harm to the telephone network, the telephone
company may discontinue your service temporarily. If possible, they will notify you
in advance. But if advance notice is not practical, you will be notified as soon as
possible. You will be informed of your right to file a complaint with the FCC. Your
telephone company may make changes in its facilities, equipment, operations or
procedures that could affect the proper functioning of your equipment. If they do,
you will be notified in advance to give you an opportunity to maintain
uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact the
following address and phone number for information on obtaining service or repairs.
~70~
The telephone company may ask that you disconnect this equipment from the
network until the problem has been corrected or until you are sure that the
equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs.
condition que la somme d'indicesd'équivalence de la sonnerie de tous les dispositifs
n'excède pas 5. »
Company: EnGenius Technologies
Address: 1580 Scenic Avenue, Costa Mesa, CA92626
Tel no.: 888.735.7888 ext. 827
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
requirements adopted by the ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible
modular jack that is also compliant. See installation instructions for details.
''NOTICE: This equipment meets the applicable Industry Canada Terminal
Equipment Technical Specifications. This is confirmed by the registration number.
The abbreviation, IC, before the registration number signifies that registration was
performed based on a Declaration of Conformity indicating that Industry Canada
technical specifications were met. It does not imply that Industry Canada approved
the equipment.”
''NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.
The REN assigned to each terminal equipment provides an indication of the
maximum number of terminals allowed to be connected to a telephone interface.
The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers of all the
devices does not exceed five.''
« AVIS : Le présent matériel est conforme aux spécifications techniques d’Industrie
Canadaapplicables au matériel terminal. Cette conformité est confirmée par le
numérod'enregistrement. Le sigle IC, placé devant le numéro d'enregistrement,
signifie quel’enregistrement s’est effectué conformément à une déclaration de
conformité et indique queles spécifications techniques d'Industrie Canada ont été
respectées. Il n’implique pasqu’Industrie Canada a approuvé le matériel. »
« AVIS : L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.
L'IESassigné à chaque dispositif terminal indique le nombre maximal de terminaux
qui peuvent êtreraccordés à une interface téléphonique. La terminaison d'une
interface peut consister en unecombinaison quelconque de dispositifs, à la seule
~71~
~72~
DTMF Duration, 12, 46
Index
Equipment Checklist, 4
2-WAY INTERCOM, 7
Adjust Handset Microphone Gain, 42
Adjust Headset, 42
Adjusting Handset Receiver (Earpiece) Voice Volume, 26
Adjusting Handset Speakerphone Voice Volume, 26
Auto Hang Up, 13, 47
Base Illustration, 14
Base Operation, 20
Base PIN, 13, 46, 47
Base Station, 4, 6, 15, 18, 19, 23
Battery Recharge a nd Replacement, 28
Battery Strength, 6
Broadcast, 23
Broadcasting a group of handsets, 23
Broadcasting all handsets, 23
Broadcasting an individual handset, 24
Call Barring, 10, 12, 39, 40, 41
Call Hold, 10
Call Log, 9, 38
Call Manager, 9, 39, 40, 45
Call Settings, 10, 11, 30, 40, 44, 47, 48
Call Timer, 11
Call Transfer, 31
Call Waiting with Caller ID, 8, 46
Caller ID, 8, 9, 25, 37, 38, 42, 47
Change PIN, 12, 47
Charger Features, 17
Charger Illustration, 16
De-registration, 29
Direct transfer, 31
DND, 9
Do Not Disturb (Silent Ring), 27
~73~
Feature Call, 11, 36, 45
Flash, 7, 12, 36, 47
Group ID, 8, 23
Group Selections, 30
Group Setting, 11
Handset and Charger Installation, 19
Handset Charging Slot, 17
Handset Features, 6, 8
Handset Group Subscription, 23, 30, 45
Handset ID, 6, 8, 24, 25, 29, 35
Handset Registration, 19, 29, 47
Handset to Handset Calls, 23
Headset Ring, 13, 42, 46
idle mode, 10
Incoming, 9, 39
Indirect transfer, 31
Key Guard, 27, 28, 44
Key Tone, 44
Key Volume, 44
Line Detection, 47
Making a Telephone Call, 22
Making an 2-Way/ Intercom Call, 22
Menu Display, 11, 12, 47
MENU mode, 20
Multiple handsets registration, 8
Mute, 10, 27
Name tagging with caller ID, 8
~74~
Outdoor Antenna, 4
Outgoing, 9, 39, 40
Phone Settings, 11, 13, 42, 45, 47, 48
Phonebook, 10, 32, 37, 44, 46
Placing a Call On Hold, 26
Programmable Feature Call, 36
Programmable Flash, 12
Receiving a Telephone Call, 24
Receiving an Intercom Call, 25
Redial, 9, 24
REG, 20
registration mode, 15, 29, 30
RESET Button, 15
Ring Volume, 44
Ringer, 6, 7, 8
RSSI, 6
Set Time, 13, 47
SILENT, 10, 25, 27, 45
speakerphone, 7, 23, 24, 26
Speed dial, 22
Talk mode, 8
TALK/FLASH, 7
transformer, 18, 19
Vibrator, 8
View Call Log, 38
Visual Message Waiting Indicator, 41
warning message, 17
~75~

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 38
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
Producer                        : GPL Ghostscript 9.04
Keywords                        : ()
Modify Date                     : 2015:01:30 11:16:53+08:00
Create Date                     : 2015:01:30 11:16:53+08:00
Creator Tool                    : PDFCreator Version 1.2.3
About                           : f71cfad6-aa89-11e4-0000-90f43f967d2.8�.2015-01-30T11:16:53+08:00
Document ID                     : uuid:f71cfad6-aa89-11e4-0000-90f43f967d2��„ �c..
Format                          : application/pdf
Title                           : SP-935_User Manual_Jan292015
Creator                         : aihsu
Description                     : ()
Author                          : aihsu
Subject                         : 

EXIF Metadata provided by EXIF.tools